Trace successful packet transmission (kernel_sendmsg() succeeded, that is)
in AF_RXRPC. We can share the enum that defines the transmission points
with the trace_rxrpc_tx_fail() tracepoint, so rename its constants to be
applicable to both.
Also, save the internal call->debug_id in the rxrpc_channel struct so that
it can be used in retransmission trace lines.
Signed-off-by: David Howells <dhowells@redhat.com>
Show the four current call IDs in /proc/net/rxrpc/conns.
Show the current packet Rx serial number in /proc/net/rxrpc/calls.
Signed-off-by: David Howells <dhowells@redhat.com>
Display in /proc/net/rxrpc/calls the timeout by which a call next expects
to receive a packet.
This makes it easier to debug timeout issues.
Signed-off-by: David Howells <dhowells@redhat.com>
Variables 'sp' and 'did_discard' are being assigned,
but are never used, hence they are redundant and can be removed.
fix following warning:
net/rxrpc/call_event.c:165:25: warning: variable 'sp' set but not used [-Wunused-but-set-variable]
net/rxrpc/conn_client.c:1054:7: warning: variable 'did_discard' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Merge turbostat utility fixes for final 4.18:
- Fix the -S option on 1-CPU systems.
- Fix computations using incorrect processor core counts.
- Fix the x2apic debug message.
- Fix logical node enumeration to allow for non-sequential physical nodes.
- Fix reported family on modern AMD processors.
- Clarify the RAPL column information in the man page.
* pm-tools:
tools/power turbostat: version 18.07.27
tools/power turbostat: Read extended processor family from CPUID
tools/power turbostat: Fix logical node enumeration to allow for non-sequential physical nodes
tools/power turbostat: fix x2apic debug message output file
tools/power turbostat: fix bogus summary values
tools/power turbostat: fix -S on UP systems
tools/power turbostat: Update turbostat(8) RAPL throttling column description
In commit ab123fe071 ("enic: handle mtu change for vf properly")
ASSERT_RTNL() is added to _enic_change_mtu() to prevent it from being
called without rtnl held. enic_probe() calls enic_change_mtu()
without rtnl held. At this point netdev is not registered yet.
Remove call to enic_change_mtu and assign the mtu to netdev->mtu.
Fixes: ab123fe071 ("enic: handle mtu change for vf properly")
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_frag_queue() might call pskb_pull() on one skb that
is already in the fragment queue.
We need to take care of possible truesize change, or we
might have an imbalance of the netns frags memory usage.
IPv6 is immune to this bug, because RFC5722, Section 4,
amended by Errata ID 3089 states :
When reassembling an IPv6 datagram, if
one or more its constituent fragments is determined to be an
overlapping fragment, the entire datagram (and any constituent
fragments) MUST be silently discarded.
Fixes: 158f323b98 ("net: adjust skb->truesize in pskb_expand_head()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently check current frags memory usage only when
a new frag queue is created. This allows attackers to first
consume the memory budget (default : 4 MB) creating thousands
of frag queues, then sending tiny skbs to exceed high_thresh
limit by 2 to 3 order of magnitude.
Note that before commit 648700f76b ("inet: frags: use rhashtables
for reassembly units"), work queue could be starved under DOS,
getting no cpu cycles.
After commit 648700f76b, only the per frag queue timer can eventually
remove an incomplete frag queue and its skbs.
Fixes: b13d3cbfb8 ("inet: frag: move eviction of queues to work queue")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jann Horn <jannh@google.com>
Cc: Florian Westphal <fw@strlen.de>
Cc: Peter Oskolkov <posk@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJbYMQXAAoJEEg/ir3gV/o+BNcH/R6X7oxLoskYIO9nWejdMKUj
GzojL3mne33mKGEwGyFfLmRWQMbgPUvYrk5mXu/1uFPAHzRA+BwioZeyeWxfCYFe
blJuv59A1EBudSvQKUDEMeXaQYD7/6T92fbu3ZvGiZEZI+OTj3z6PtBU0Tr6NEMZ
zxRKWkpLPdjUwJh51tXEgfmEqy+gnn9tNIZt8ClRJ0w5wbgnignhzx1lCry1SE95
6zNS8aZKRxSIaVY41MxLSTRb9jLBmeZtiD67ntJAZIaLaMIMUqZbhW5Rtt7rz8HZ
chAiY8KdmEM35Ix6+ovzT9FKz/Jhp6/0nDioNYPRT5D3rHcqe+wUb8/8zROnhgs=
=b9YA
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2018-07-31' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2018-07-31
The following series includes four mlx5 fixes.
Please pull and let me know if there's any problem.
For -stable v4.14
net/mlx5e: E-Switch, Initialize eswitch only if eswitch manager
For -stable v4.16
net/mlx5e: Set port trust mode to PCP as default
For -stable v4.17
net/mlx5e: IPoIB, Set the netdevice sw mtu in ipoib enhanced flow
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=MN3z
-----END PGP SIGNATURE-----
Merge tag 'audit-pr-20180731' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit
Pull audit fix from Paul Moore:
"A single small audit fix to guard against memory allocation failures
when logging information about a kernel module load.
It's small, easy to understand, and self-contained; while nothing is
zero risk, this should be pretty low"
* tag 'audit-pr-20180731' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit:
audit: fix potential null dereference 'context->module.name'
local_timer_softirq_pending() checks whether the timer softirq is
pending with: local_softirq_pending() & TIMER_SOFTIRQ.
This is wrong because TIMER_SOFTIRQ is the softirq number and not a
bitmask. So the test checks for the wrong bit.
Use BIT(TIMER_SOFTIRQ) instead.
Fixes: 5d62c183f9 ("nohz: Prevent a timer interrupt storm in tick_nohz_stop_sched_tick()")
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Daniel Bristot de Oliveira <bristot@redhat.com>
Acked-by: Frederic Weisbecker <frederic@kernel.org>
Cc: bigeasy@linutronix.de
Cc: peterz@infradead.org
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20180731161358.29472-1-anna-maria@linutronix.de
After introduction of the cited commit, mlx5e_build_nic_params
receives the netdevice mtu in order to set the sw_mtu of mlx5e_params.
For enhanced IPoIB, the netdevice mtu is not set in this stage,
therefore, the initial sw_mtu equals zero. As a result, the hw_mtu
of the receive queue will be calculated incorrectly causing traffic
issues.
To fix this issue, query for port mtu before building the nic params.
Fixes: 472a1e44b3 ("net/mlx5e: Save MTU in channels params")
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
MTU helper function is used by both conventional mlx5e
instances (PF/VF) and the eswitch representors. The representor
shouldn't change the nic vport context MTU, the VF is responsible for
that. Therefore set_mtu_cb has a null value when changing the
representor MTU.
Fixes: 250a42b6a7 ("net/mlx5e: Support configurable MTU for vport representors")
Signed-off-by: Adi Nissim <adin@mellanox.com>
Reviewed-by: Yevgeny Kliteynik <kliteyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The hairpin offload code has dependency on the trust mode being PCP.
Hence we should set PCP as the default for handling cases where we are
disallowed to read the trust mode from the FW, or failed to initialize it.
Fixes: 106be53b6b ('net/mlx5e: Set per priority hairpin pairs')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Execute mlx5_eswitch_init() only if we have MLX5_ESWITCH_MANAGER
capabilities.
Do the same for mlx5_eswitch_cleanup().
Fixes: a9f7705ffd ("net/mlx5: Unify vport manager capability check")
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
We never use RCU protection for it, just a lot of cargo-cult
rcu_deference_protects calls.
Note that we do keep the kfree_rcu call for it, as the references through
struct sock are RCU protected and thus might require a grace period before
freeing.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Version 1 of the patch adding SERDES support to the 88E6141/6341
correctly added the ops to the 88E6141/6341. However, by the time
version 3 was committed, the ops had moved to the 88E6085/6175. Put
them back where they belong.
Fixes: 5bafeb6e7e ("net: dsa: mv88e6xxx: 88E6141/6341 SERDES support")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Last set of fixes before 4.18 is released
iwlwifi
* add new IDs for cards already available on the market
brcmfmac
* fix a regression introduced in v4.17
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJbYDWEAAoJEG4XJFUm622bPGUH+QHGcuazgPqR4TsQXwmfNdJB
HJdsx90WW6TLMDzF9EquA4ontBggq2Mdnorxt1SIXK+ZeajFWZlKyl5ol24TtOH3
9uFhQRID2KlWPnwgrBTsFAiNNJar+X4GoUX1SqFz8VJnkYgfdtBHaVK59HdWSp5e
2rVaG/ORUMNnY58f6jr9wOhn/miC1CKuJk5j83CN2KlETkqj/VoGUE2dShdJl0wu
+4iYznIwhG9f6KykReaBmJbh4xu6AEqkFbadKGwWcChR3DDmzDAsWzkcWEocx8ZY
EpoF6vW8GoBB2RE2Syg/Y6exQGnDb4itYQYxvJV1qV52XwYfvDzCdlbLn+kv34I=
=4wJj
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2018-07-31' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.18
Last set of fixes before 4.18 is released
iwlwifi
* add new IDs for cards already available on the market
brcmfmac
* fix a regression introduced in v4.17
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't maintain tx counters in rx stats any more. There's no need
for an extra container of rq stats.
Cc: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 5b8f3c8d30 ("virtio_net: Add XDP related stats") tries to
count TX XDP stats in virtnet_receive(). This will cause several
issues:
- virtnet_xdp_sq() was called without checking whether or not XDP is
set. This may cause out of bound access when there's no enough txq
for XDP.
- Stats were updated even if there's no XDP/XDP_TX.
Fixing this by reusing virtnet_xdp_xmit() for XDP_TX which can counts
TX XDP counter itself and remove the unnecessary tx stats embedded in
rx stats.
Reported-by: syzbot+604f8271211546f5b3c7@syzkaller.appspotmail.com
Fixes: 5b8f3c8d30 ("virtio_net: Add XDP related stats")
Cc: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski says:
====================
xsk: improvements to RX queue check and replace
First 3 patches of my recent RFC. The first one make the check against
real_num_rx_queues slightly more reliable, while the latter two redefine
XDP_QUERY_XSK_UMEM slightly to disallow replacing UMEM in the driver at
the stack level.
I'm not sure where this lays on the bpf vs net trees scale, but there
should be no conflicts with either tree.
====================
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently drivers have to check if they already have a umem
installed for a given queue and return an error if so. Make
better use of XDP_QUERY_XSK_UMEM and move this functionality
to the core.
We need to keep rtnl across the calls now.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Acked-by: Björn Töpel <bjorn.topel@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return early and only take the ref on dev once there is no possibility
of failing.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Acked-by: Björn Töpel <bjorn.topel@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We used to depend on real_num_rx_queues as a upper bound for sanity
checks. For AF_XDP socket validation it's useful if the check behaves
the same regardless of CONFIG_SYSFS setting.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nine fixes, five in the qla2xxx driver, the most serious of which is
the uninitialized list head crash which can be observed in most
systems under a sufficiently loaded low memory environment. The two
sg fixes are minor but obvious and two target ones which seem
reasonable but not high impact.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCW2B83yYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishfjaAQDN5p+O
kB54JeM3Ae0IT7StDsK+LECoeGj2fYACBH+wUQD/eOZEXi6pDJ796VJWwjfqnxWb
6Eonm3Qtikxj/Q4Z78w=
=k2Af
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Nine fixes, five in the qla2xxx driver, the most serious of which is
the uninitialized list head crash which can be observed in most
systems under a sufficiently loaded low memory environment.
The two sg fixes are minor but obvious and two target ones which seem
reasonable but not high impact"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: qla2xxx: Return error when TMF returns
scsi: qla2xxx: Fix ISP recovery on unload
scsi: qla2xxx: Fix driver unload by shutting down chip
scsi: qla2xxx: Fix NPIV deletion by calling wait_for_sess_deletion
scsi: qla2xxx: Fix unintialized List head crash
scsi: sg: update comment for blk_get_request()
scsi: sg: fix minor memory leak in error path
scsi: libiscsi: fix possible NULL pointer dereference in case of TMF
scsi: target: iscsi: cxgbit: fix max iso npdu calculation
Commit 58b99ee3e3 ("net/mlx5e: Add support for XDP_REDIRECT in device-out side")
forgot to return/free the xdp_frame in case the DMA mapping failed, correct this.
Also DMA unmap the frame in case mlx5e_xmit_xdp_frame() fails.
Fixes: 58b99ee3e3 ("net/mlx5e: Add support for XDP_REDIRECT in device-out side")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some bugfixes that seem important and safe enough to merge at the last
minute.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJbXxanAAoJECgfDbjSjVRpDqoH/iqUcK2KkLQTUut4KWF0xjfs
0AZxB9sT2fXNAwF4dDS0SywN8oXKRA0c83AY5WgtcJfndPYEhg4mZsiQThLN6GVw
/CRVizpN1mSbn7ds4Xl5htD2Ml8OxRkAdulOXfG/DZ2eIiEgoQ6vPzDF2jqy1dIj
yWjBNWoSKIqElkN310BlkDX0hjqSP9zr4kEDFSB7AHcsNRhUDcgRqFzA83bRZU0b
qKNzeLwU28jYnjzBPjQ449lkHGXtSjSkBnxUOXHU2CVCiQ5I0rBPi/Xdhtd94gDM
Bbl4Spf74IiwPdfMwk4pa6rO8JPLpYhrFHIG0Gkk8AFV4Gwh1IYQ9s3On3ADWSQ=
=p1AG
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio fixes from Michael Tsirkin:
"Some bugfixes that seem important and safe enough to merge at the last
minute"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_balloon: fix another race between migration and ballooning
tools/virtio: add kmalloc_array stub
tools/virtio: add dma barrier stubs
- Fix a recent ACPICA regression introduced by a previous fix
that caused control method execution at the table level to be
mishandled by mistake (Erik Schmauss).
- Fix a hibernation regression from the 4.15 cycle in the ACPI
driver for Intel SoCs (LPSS) that caused the platform firmware
to be confused during resume from hibernation by the driver's
PM quirks which was fixed for system-wide suspend/resume (ACPI
S3) earlier in this cycle, but that previous fix missed the
hibernation (ACPI S4) case (Rafael Wysocki).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=N9R3
-----END PGP SIGNATURE-----
Merge tag 'acpi-urgent-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These fix a recent ACPICA regression affecting control method
execution at the table level and an earlier hibernation regression in
the ACPI driver for Intel SoCs (LPSS) that was missed by a previous
fix in this cycle.
Specifics:
- Fix a recent ACPICA regression introduced by a previous fix that
caused control method execution at the table level to be mishandled
by mistake (Erik Schmauss).
- Fix a hibernation regression from the 4.15 cycle in the ACPI driver
for Intel SoCs (LPSS) that caused the platform firmware to be
confused during resume from hibernation by the driver's PM quirks
which was fixed for system-wide suspend/resume (ACPI S3) earlier in
this cycle, but that previous fix missed the hibernation (ACPI S4)
case (Rafael Wysocki)"
* tag 'acpi-urgent-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPICA: AML Parser: ignore control method status in module-level code
ACPI / LPSS: Avoid PM quirks on suspend and resume from hibernation
When a PCI device is detected, pdev->is_added is set to 1 and proc and
sysfs entries are created.
When the device is removed, pdev->is_added is checked for one and then
device is detached with clearing of proc and sys entries and at end,
pdev->is_added is set to 0.
is_added and is_busmaster are bit fields in pci_dev structure sharing same
memory location.
A strange issue was observed with multiple removal and rescan of a PCIe
NVMe device using sysfs commands where is_added flag was observed as zero
instead of one while removing device and proc,sys entries are not cleared.
This causes issue in later device addition with warning message
"proc_dir_entry" already registered.
Debugging revealed a race condition between the PCI core setting the
is_added bit in pci_bus_add_device() and the NVMe driver reset work-queue
setting the is_busmaster bit in pci_set_master(). As these fields are not
handled atomically, that clears the is_added bit.
Move the is_added bit to a separate private flag variable and use atomic
functions to set and retrieve the device addition state. This avoids the
race because is_added no longer shares a memory location with is_busmaster.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=200283
Signed-off-by: Hari Vyas <hari.vyas@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Calling pmull_gcm_encrypt_block() requires kernel_neon_begin() and
kernel_neon_end() to be used since the routine touches the NEON
register file. Add the missing calls.
Also, since NEON register contents are not preserved outside of
a kernel mode NEON region, pass the key schedule array again.
Fixes: 7c50136a8a ("crypto: arm64/aes-ghash - yield NEON after every ...")
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Dynamic boosting of HWP performance on IO wake showed significant
improvement to IO workloads. This series was intended for Skylake Xeon
platforms only and feature was enabled by default based on CPU model
number.
But some Xeon platforms reused the Skylake desktop CPU model number. This
caused some undesirable side effects to some graphics workloads. Since
they are heavily IO bound, the increase in CPU performance decreased the
power available for GPU to do its computing and hence decrease in graphics
benchmark performance.
For example on a Skylake desktop, GpuTest benchmark showed average FPS
reduction from 529 to 506.
This change makes sure that HWP boost feature is only enabled for Skylake
server platforms by using ACPI FADT preferred PM Profile. If some desktop
users wants to get benefit of boost, they can still enable boost from
intel_pstate sysfs attribute "hwp_dynamic_boost".
Fixes: 41ab43c9c8 (cpufreq: intel_pstate: enable boost for Skylake Xeon)
Link: https://bugs.freedesktop.org/show_bug.cgi?id=107410
Reported-by: Eero Tamminen <eero.t.tamminen@intel.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Reviewed-by: Francisco Jerez <currojerez@riseup.net>
Acked-by: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Merge a fix for hibernation regression in the ACPI driver for Intel
SoCs (LPSS).
* acpi-soc:
ACPI / LPSS: Avoid PM quirks on suspend and resume from hibernation
- Update the tools copy of several files, including perf_event.h,
powerpc's asm/unistd.h (new io_pgetevents syscall), bpf.h and
x86's memcpy_64.s (used in 'perf bench mem'), silencing the
respective warnings during the perf tools build.
- Fix the build on the alpine:edge distro.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEELb9bqkb7Te0zijNb1lAW81NSqkAFAltfcukACgkQ1lAW81NS
qkDlVA//fNnB+pDgqDI9MHhaAxPWxWmmBfz49g1i+Yv5MqBTSAXUkdP6MuTSHXkS
KHGWBHYjb56gORqQZRLf9hFbiM1XYHL97uU55zKd/9zhuqhpIIDCEBq+RS9hwPzH
DMrpHvOKHGwr0NE/O90HPYcnqSZUWarpwY8O+l1o5R6KW8EMneNvZypc7AbBcRfv
P8QzdJ2NpeFgkvO6xEk0LnwrQQkgs/7VlpwJ0bsJ471Q9ujB+YgHd6PnX+hvxsy+
QdTrpN0NSgBYtRPanprXyMnYsWEUhLlVqlY4qpGJBzdQKfMGWriG9a+jihKQXwdl
ntgfs/aUphRhDcd0Rk6pR3dcozzB4mHYLI4ieN8t+QqisLJZV4RVppgLflq5sMAj
xC3Gbn/GZqxLnh4qgoWvYndOEEDm3KNvEtCTe+rBVxdXvLksQevXrpMi8QbCZsZ9
xU5DB42fK+8Vd9Bg89UxhI6BKgA8CDzHps3JXSp64314m4+0bswXdpCauhT3LUqg
/W57VL2py8f8xrJqDmWohVH02qVgLU5RElFZWKmq04scfV8ypwEyWQSOb5MNCOgH
+Malh+LbTrqz2VxIprjszNIejqp7dyoMgcJeGkvBJvwtw6uViubY30YOuwewwoGI
UeNFwbNXzT6KgsJmlQCB6h9RnvY/vaU01rG0LSoxRjU9WReHPqw=
=r5Gg
-----END PGP SIGNATURE-----
Merge tag 'perf-urgent-for-mingo-4.18-20180730' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent
Pull perf/urgent fixes from Arnaldo Carvalho de Melo:
- Update the tools copy of several files, including perf_event.h,
powerpc's asm/unistd.h (new io_pgetevents syscall), bpf.h and
x86's memcpy_64.s (used in 'perf bench mem'), silencing the
respective warnings during the perf tools build.
- Fix the build on the alpine:edge distro.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Masayoshi Mizuma reported that a warning message is shown while a CPU is
hot-removed on Broadwell servers:
WARNING: CPU: 126 PID: 6 at arch/x86/events/intel/uncore.c:988
uncore_pci_remove+0x10b/0x150
Call Trace:
pci_device_remove+0x42/0xd0
device_release_driver_internal+0x148/0x220
pci_stop_bus_device+0x76/0xa0
pci_stop_root_bus+0x44/0x60
acpi_pci_root_remove+0x1f/0x80
acpi_bus_trim+0x57/0x90
acpi_bus_trim+0x2e/0x90
acpi_device_hotplug+0x2bc/0x4b0
acpi_hotplug_work_fn+0x1a/0x30
process_one_work+0x174/0x3a0
worker_thread+0x4c/0x3d0
kthread+0xf8/0x130
This bug was introduced by:
commit 15a3e845b0 ("perf/x86/intel/uncore: Fix SBOX support for Broadwell CPUs")
The index of "QPI Port 2 filter" was hardcode to 2, but this conflicts with the
index of "PCU.3" which is "HSWEP_PCI_PCU_3", which equals to 2 as well.
To fix the conflict, the hardcoded index needs to be cleaned up:
- introduce a new enumerator "BDX_PCI_QPI_PORT2_FILTER" for "QPI Port 2
filter" on Broadwell,
- increase UNCORE_EXTRA_PCI_DEV_MAX by one,
- clean up the hardcoded index.
Debugged-by: Masayoshi Mizuma <m.mizuma@jp.fujitsu.com>
Suggested-by: Ingo Molnar <mingo@kernel.org>
Reported-by: Masayoshi Mizuma <m.mizuma@jp.fujitsu.com>
Tested-by: Masayoshi Mizuma <m.mizuma@jp.fujitsu.com>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: msys.mizuma@gmail.com
Cc: stable@vger.kernel.org
Fixes: 15a3e845b0 ("perf/x86/intel/uncore: Fix SBOX support for Broadwell CPUs")
Link: http://lkml.kernel.org/r/1532953688-15008-1-git-send-email-kan.liang@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull networking fixes from David Miller:
"Several smallish fixes, I don't think any of this requires another -rc
but I'll leave that up to you:
1) Don't leak uninitialzed bytes to userspace in xfrm_user, from Eric
Dumazet.
2) Route leak in xfrm_lookup_route(), from Tommi Rantala.
3) Premature poll() returns in AF_XDP, from Björn Töpel.
4) devlink leak in netdevsim, from Jakub Kicinski.
5) Don't BUG_ON in fib_compute_spec_dst, the condition can
legitimately happen. From Lorenzo Bianconi.
6) Fix some spectre v1 gadgets in generic socket code, from Jeremy
Cline.
7) Don't allow user to bind to out of range multicast groups, from
Dmitry Safonov with a follow-up by Dmitry Safonov.
8) Fix metrics leak in fib6_drop_pcpu_from(), from Sabrina Dubroca"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (41 commits)
netlink: Don't shift with UB on nlk->ngroups
net/ipv6: fix metrics leak
xen-netfront: wait xenbus state change when load module manually
can: ems_usb: Fix memory leak on ems_usb_disconnect()
openvswitch: meter: Fix setting meter id for new entries
netlink: Do not subscribe to non-existent groups
NET: stmmac: align DMA stuff to largest cache line length
tcp_bbr: fix bw probing to raise in-flight data for very small BDPs
net: socket: Fix potential spectre v1 gadget in sock_is_registered
net: socket: fix potential spectre v1 gadget in socketcall
net: mdio-mux: bcm-iproc: fix wrong getter and setter pair
ipv4: remove BUG_ON() from fib_compute_spec_dst
enic: handle mtu change for vf properly
net: lan78xx: fix rx handling before first packet is send
nfp: flower: fix port metadata conversion bug
bpf: use GFP_ATOMIC instead of GFP_KERNEL in bpf_parse_prog()
bpf: fix bpf_skb_load_bytes_relative pkt length check
perf build: Build error in libbpf missing initialization
net: ena: Fix use of uninitialized DMA address bits field
bpf: btf: Use exact btf value_size match in map_check_btf()
...
Pull sparc fixes from David Miller:
"Some small __init annotation and build fixes from Stephen Rostedt and
Thomas Petazzoni"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc: use asm-generic version of msi.h
sparc: move MSI related definitions to where they are used
sparc/time: Add missing __init to init_tick_ops()
Anatoly reports another squashfs fuzzing issue, where the decompression
parameters themselves are in a compressed block.
This causes squashfs_read_data() to be called in order to read the
decompression options before the decompression stream having been set
up, making squashfs go sideways.
Reported-by: Anatoly Trosinenko <anatoly.trosinenko@gmail.com>
Acked-by: Phillip Lougher <phillip.lougher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
xdp_return_buff() is used when frame has been successfully
handled (transmitted) or if an error occurred during delayed
processing and there is no way to report it back to
xdp_do_redirect().
In case of __xsk_rcv_zc() error is propagated all the way
back to the driver, so there is no need to call
xdp_return_buff(). Driver will recycle the frame anyway
after seeing that error happened.
Fixes: 173d3adb6f ("xsk: add zero-copy support for Rx")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
I hit the following problem when I tried to use bpftool
to dump a percpu array.
$ sudo ./bpftool map show
61: percpu_array name stub flags 0x0
key 4B value 4B max_entries 1 memlock 4096B
...
$ sudo ./bpftool map dump id 61
bpftool: malloc.c:2406: sysmalloc: Assertion
`(old_top == initial_top (av) && old_size == 0) || \
((unsigned long) (old_size) >= MINSIZE && \
prev_inuse (old_top) && \
((unsigned long) old_end & (pagesize - 1)) == 0)'
failed.
Aborted
Further debugging revealed that this is due to
miscommunication between bpftool and kernel.
For example, for the above percpu_array with value size of 4B.
The map info returned to user space has value size of 4B.
In bpftool, the values array for lookup is allocated like:
info->value_size * get_possible_cpus() = 4 * get_possible_cpus()
In kernel (kernel/bpf/syscall.c), the values array size is
rounded up to multiple of 8.
round_up(map->value_size, 8) * num_possible_cpus()
= 8 * num_possible_cpus()
So when kernel copies the values to user buffer, the kernel will
overwrite beyond user buffer boundary.
This patch fixed the issue by allocating and stepping through
percpu map value array properly in bpftool.
Fixes: 71bb428fe2 ("tools: bpf: add bpftool")
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The variable 'context->module.name' may be null pointer when
kmalloc return null, so it's better to check it before using
to avoid null dereference.
Another one more thing this patch does is using kstrdup instead
of (kmalloc + strcpy), and signal a lost record via audit_log_lost.
Cc: stable@vger.kernel.org # 4.11
Signed-off-by: Yi Wang <wang.yi59@zte.com.cn>
Reviewed-by: Jiang Biao <jiang.biao2@zte.com.cn>
Reviewed-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
This is necessary to be able to include <linux/msi.h> when
CONFIG_GENERIC_MSI_IRQ_DOMAIN is enabled. Without this, a build with
CONFIG_GENERIC_MSI_IRQ_DOMAIN fails with:
In file included from drivers//ata/ahci.c:45:0:
>> include/linux/msi.h:226:10: error: unknown type name 'msi_alloc_info_t'; did you mean 'sg_alloc_fn'?
msi_alloc_info_t *arg);
^~~~~~~~~~~~~~~~
sg_alloc_fn
include/linux/msi.h:230:9: error: unknown type name 'msi_alloc_info_t'; did you mean 'sg_alloc_fn'?
msi_alloc_info_t *arg);
^~~~~~~~~~~~~~~~
sg_alloc_fn
include/linux/msi.h:239:12: error: unknown type name 'msi_alloc_info_t'; did you mean 'sg_alloc_fn'?
msi_alloc_info_t *arg);
^~~~~~~~~~~~~~~~
sg_alloc_fn
include/linux/msi.h:240:22: error: unknown type name 'msi_alloc_info_t'; did you mean 'sg_alloc_fn'?
void (*msi_finish)(msi_alloc_info_t *arg, int retval);
^~~~~~~~~~~~~~~~
sg_alloc_fn
include/linux/msi.h:241:20: error: unknown type name 'msi_alloc_info_t'; did you mean 'sg_alloc_fn'?
void (*set_desc)(msi_alloc_info_t *arg,
^~~~~~~~~~~~~~~~
sg_alloc_fn
include/linux/msi.h:316:18: error: unknown type name 'msi_alloc_info_t'; did you mean 'sg_alloc_fn'?
int nvec, msi_alloc_info_t *args);
^~~~~~~~~~~~~~~~
sg_alloc_fn
include/linux/msi.h:318:29: error: unknown type name 'msi_alloc_info_t'; did you mean 'sg_alloc_fn'?
int virq, int nvec, msi_alloc_info_t *args);
^~~~~~~~~~~~~~~~
sg_alloc_fn
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The definitions in arch/sparc/include/asm/msi.h are only used in
arch/sparc/mm/srmmu.c, so it makes sense to have them in the C file
directly.
In addition, having a custom arch/sparc/include/asm/msi.h prevents
from using the asm-generic version of this header, which is necessary
to be able to include <linux/msi.h> when CONFIG_GENERIC_MSI_IRQ_DOMAIN
is enabled.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Code that was added to force gcc not to inline any function that isn't
explicitly declared as inline uncovered that init_tick_ops() isn't
marked as "__init". It is only called by __init functions and more
importantly it too calls an __init function which would require it to be
__init as well.
Link: http://lkml.kernel.org/r/201806060444.hdHcKOBy%fengguang.wu@intel.com
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
On i386 nlk->ngroups might be 32 or 0. Which leads to UB, resulting in
hang during boot.
Check for 0 ngroups and use (unsigned long long) as a type to shift.
Fixes: 7acf9d4237 ("netlink: Do not subscribe to non-existent groups").
Reported-by: kernel test robot <rong.a.chen@intel.com>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements following ethtool stats fields for netvsc:
cpu<n>_tx/rx_packets/bytes
cpu<n>_vf_tx/rx_packets/bytes
Corresponding per-cpu counters already exist in current code. Exposing
these counters will help troubleshooting performance issues.
for_each_present_cpu() was used instead of for_each_possible_cpu().
for_each_possible_cpu() would create very long and useless output.
It is still being used for internal buffer, but not for ethtool
output.
There could be an overflow if cpu was added between ethtool
call netvsc_get_sset_count() and netvsc_get_ethtool_stats() and
netvsc_get_strings(). (still safe if cpu was removed)
ethtool makes these three function calls separately.
As long as we use ethtool, I can't see any clean solution.
Currently and in foreseeable short term, Hyper-V doesn't support
cpu hot-plug. Plus, ethtool is for admin use. Unlikely the admin
would perform such combo operations.
Changes in v2:
- Remove cpp style comment
- Resubmit after freeze
Changes in v3:
- Reimplemented with kvmalloc instead of alloc_percpu
Changes in v4:
- Fixed inconsistent array size
- Use kvmalloc_array instead of kvmalloc
Signed-off-by: Yidong Ren <yidren@microsoft.com>
Reviewed-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEENrCndlB/VnAEWuH5k9IU1zQoZfEFAlte1NUTHG1rbEBwZW5n
dXRyb25peC5kZQAKCRCT0hTXNChl8Z0zB/9CkuxbUOB8QsoorZ6NwoVcK4wNZNhN
SRB8BpJpZn+Bye5hxKvMXU3yeoZj5xIR4mopLiiKM/pp3y3yqk3uhh971SQmAhfa
ULv+leBiCaFatXgYQTngOi6Xg6faJvu6ZYKUzvNPT1gW40HQTYUCCJwdgvlCbGLs
AVa04gV6o5lSolCboEjeKLnsW9ByHBBkLaOOZCixt+VfS76gO29fYJmplz7WC9pW
Udw2KiQBSz/D5iMUoYxb9KiMAa5OL9dJfHfy4jIdsEMekBUj66KjzbFOBq90c1Pg
PVEABATxFTplL1He+PzkJLu15csnhH0VSurUenkoOfdMkbu1LCmdwd4S
=053y
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-4.18-20180730' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2018-07-30
this is a pull request of one patch for net/master.
The patch by Anton Vasilyev and the Linux Driver Verification project
fixes a memory leak in the ems_usb driver's disconnect function.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull scheduler fixes from Ingo Molnar:
"Misc fixes:
- a deadline scheduler related bug fix which triggered a kernel
warning
- an RT_RUNTIME_SHARE fix
- a stop_machine preemption fix
- a potential NULL dereference fix in sched_domain_debug_one()"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/rt: Restore rt_runtime after disabling RT_RUNTIME_SHARE
sched/deadline: Update rq_clock of later_rq when pushing a task
stop_machine: Disable preemption after queueing stopper threads
sched/topology: Check variable group before dereferencing it
