This adds a driver for panels based on the WideChips WS2401 display
controller. This display controller is used in the Samsung LMS380KF01
display found in the Samsung GT-I8160 (Codina) mobile phone and
possibly others.
As is common with Samsung displays manufacturer commands are necessary
to configure the display to a working state.
The display optionally supports internal backlight control, but can
also use an external backlight.
This driver re-uses the DBI infrastructure to communicate with the
display.
Cc: phone-devel@vger.kernel.org
Cc: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210714225002.1065107-2-linus.walleij@linaro.org
When I tried booting up a device that needed the DP AUX backlight, I
found an error in the logs:
panel-simple-dp-aux: probe of aux-ti_sn65dsi86.aux.0 failed with error -110
The aux transfers were failing because the panel wasn't powered. Just
like when reading the EDID we need to power the panel when trying to
talk to it. Add the needed pm_runtime calls.
After I do this I can successfully probe the panel and adjust the
backlight on my board.
Fixes: bfd451403d ("drm/panel-simple: Support DP AUX backlight")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210714093334.1.Idb41f87e5abae4aee0705db7458b0097fc50e7ab@changeid
Add support for the Innolux/Chimei EJ030NA 3.0"
320x480 TFT panel.
This panel can be found in the LDKs, RS97 V2.1 and RG300 (non IPS)
handheld gaming consoles.
While being 320x480, it is actually a horizontal 4:3
panel with non-square pixels in delta arrangement.
Signed-off-by: Christophe Branchereau <cbranchereau@gmail.com>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210625121045.81711-2-paul@crapouillou.net
This patch adds support for the EDT ETM0350G0DH6 3.5" (320x240) lcd
panel to DRM simple panel driver.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Yunus Bas <y.bas@phytec.de>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210709200349.2665205-2-y.bas@phytec.de
This patch adds support for the EDT ETMV570G2DHU 5.7" (640x480) lcd panel
to DRM simple panel driver.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Yunus Bas <y.bas@phytec.de>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210709200349.2665205-1-y.bas@phytec.de
Do not give a warning for the eDP panels if the "bus_format" is
not specified, since most eDP panels can support more than one
bus formats and this can be auto-detected.
Also, update the check to include bpc=10 for the eDP panel.
Signed-off-by: Rajeev Nandan <rajeevny@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1624726268-14869-5-git-send-email-rajeevny@codeaurora.org
If there is no backlight specified in the device tree and the panel
has access to the DP AUX channel then create a DP AUX backlight if
supported by the panel.
Signed-off-by: Rajeev Nandan <rajeevny@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1624726268-14869-3-git-send-email-rajeevny@codeaurora.org
The connector_type for following two EDT displays is missing:
- EDT ETM0430G0DH6
- EDT ETM0700G0BDH6
Both are parallel displays thus add the corresponding connector_type.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210621150930.86617-2-s.riedmueller@phytec.de
The AUO G104SN02 V2 is an LVDS display which supports 6 and 8 bpc PSWG.
Add the corresponding connector type and 8 bpc as default bus_format.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210621150930.86617-1-s.riedmueller@phytec.de
The SPI access to s6e63m0 is using the DBI protocol, so switch
to using the elaborate DBI protocol implementation in the DRM
DBI helper library.
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210614181135.1124445-2-linus.walleij@linaro.org
If panel-simple is instantiated as a DP AUX bus endpoint then we have
access to the DP AUX bus. Let's stash it in the panel-simple
structure, leaving it NULL for the cases where the panel is
instantiated in other ways.
If we happen to have access to the DP AUX bus and we weren't provided
the ddc-i2c-bus in some other manner, let's use the DP AUX bus for it.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210611101711.v10.6.I18e60221f6d048d14d6c50a770b15f356fa75092@changeid
The panel-simple driver can already have devices instantiated as
platform devices or MIPI DSI devices. Let's add a 3rd way to
instantiate it: as DP AUX endpoint devices.
At the moment there is no benefit to instantiating it in this way,
but:
- In the next patch we'll give it access to the DDC channel via the DP
AUX bus.
- Possibly in the future we may use this channel to configure the
backlight.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210611101711.v10.5.Iada41f76a7342354bae929d0bb3ceba40f27f0ea@changeid
This adds a new driver for the Samsung DB7430 DPI display
controller as controlled over SPI.
Right now the only panel product we know that is using this
display controller is the LMS397KF04 but there may be more.
This is the first regular panel driver making use of the
MIPI DBI helper library. The DBI "device" portions can not
be used because that code assumes the use of a single
regulator and specific timings around the reset pulse that
do not match the DB7430 datasheet.
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: Doug Anderson <dianders@chromium.org>
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210610220527.366432-1-linus.walleij@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/panel/panel-raspberrypi-touchscreen.c:33: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Eric Anholt <eric@anholt.net>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210602143300.2330146-21-lee.jones@linaro.org
The PM Runtime docs specifically call out the need to call
pm_runtime_dont_use_autosuspend() in the remove() callback if
pm_runtime_use_autosuspend() was called in probe():
> Drivers in ->remove() callback should undo the runtime PM changes done
> in ->probe(). Usually this means calling pm_runtime_disable(),
> pm_runtime_dont_use_autosuspend() etc.
We should do this. This fixes a warning splat that I saw when I was
testing out the panel-simple's remove().
Fixes: 3235b0f20a ("drm/panel: panel-simple: Use runtime pm to avoid excessive unprepare / prepare")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210517130450.v7.1.I9e947183e95c9bd067c9c1d51208ac6a96385139@changeid
It doesn't make sense to go out to the bus and read the EDID over and
over again. Let's cache it and throw away the cache when we turn power
off from the panel. Autosuspend means that even if there are several
calls to read the EDID before we officially turn the power on then we
should get good use out of this cache.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210423095743.v5.18.If050957eaa85cf45b10bcf61e6f7fa61c9750ebf@changeid
I don't believe that it ever makes sense to read the EDID when a panel
is not powered and the powering on of the panel is the job of
prepare(). Let's make sure that this happens before we try to read the
EDID. We use the pm_runtime functions directly rather than directly
calling the normal prepare() function because the pm_runtime functions
are definitely refcounted whereas it's less clear if the prepare() one
is.
NOTE: I'm not 100% sure how EDID reading was working for folks in the
past, but I can only assume that it was failing on the initial attempt
and then working only later. This patch, presumably, will fix that. If
some panel out there really can read the EDID without powering up and
it's a big advantage to preserve the old behavior we can add a
per-panel flag. It appears that providing the DDC bus to the panel in
the past was somewhat uncommon in any case.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210423095743.v5.17.Ibd31b8f7c73255d68c5c9f5b611b4bfaa036f727@changeid
As of commit 5186421cbf ("drm: Introduce epoch counter to
drm_connector") the drm_get_edid() function calls
drm_connector_update_edid_property() for us. There's no reason for us
to call it again.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210423095743.v5.16.Icb581b0273d95cc33ca38676c61ae6d7d2e75357@changeid
When I added support for the hpd-gpio to simple-panel in commit
48834e6084 ("drm/panel-simple: Support hpd-gpios for delaying
prepare()"), I added a special case to handle a circular dependency I
was running into on the ti-sn65dsi86 bridge chip. On my board the
hpd-gpio is actually provided by the bridge chip. That was causing
some circular dependency problems that I had to work around by getting
the hpd-gpio late.
I've now reorganized the ti-sn65dsi86 bridge chip driver to be a
collection of sub-drivers. Now the GPIO part can probe separately and
that breaks the chain. Let's get rid of the old code to clean things
up.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210423095743.v5.10.I40eeedc23459d1e3fc96fa6cdad775d88c6e706c@changeid
In commit 3235b0f20a ("drm/panel: panel-simple: Use runtime pm to
avoid excessive unprepare / prepare") we started using pm_runtime, but
my patch neglected to add the proper pm_runtime_disable(). Doh! Add
them now.
Fixes: 3235b0f20a ("drm/panel: panel-simple: Use runtime pm to avoid excessive unprepare / prepare")
Reported-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210423095743.v5.1.I9e6af2529d6c61e5daf86a15a1211121c5223b9a@changeid
Unpreparing and re-preparing a panel can be a really heavy
operation. Panels datasheets often specify something on the order of
500ms as the delay you should insert after turning off the panel
before turning it on again. In addition, turning on a panel can have
delays on the order of 100ms - 200ms before the panel will assert HPD
(AKA "panel ready"). The above means that we should avoid turning a
panel off if we're going to turn it on again shortly.
The above becomes a problem when we want to read the EDID of a
panel. The way that ordering works is that userspace wants to read the
EDID of the panel _before_ fully enabling it so that it can set the
initial mode correctly. However, we can't read the EDID until we power
it up. This leads to code that does this dance (like
ps8640_bridge_get_edid()):
1. When userspace requests EDID / the panel modes (through an ioctl),
we power on the panel just enough to read the EDID and then power
it off.
2. Userspace then turns the panel on.
There's likely not much time between step #1 and #2 and so we want to
avoid powering the panel off and on again between those two steps.
Let's use Runtime PM to help us. We'll move the existing prepare() and
unprepare() to be runtime resume() and runtime suspend(). Now when we
want to prepare() or unprepare() we just increment or decrement the
refcount. We'll default to a 1 second autosuspend delay which seems
sane given the typical delays we see for panels.
A few notes:
- It seems the existing unprepare() and prepare() are defined to be
no-ops if called extra times. We'll preserve that behavior but may
try to remove it in a future patch.
- This is a slight change in the ABI of simple panel. If something was
absolutely relying on the unprepare() to happen instantly that
simply won't be the case anymore. I'm not aware of anyone relying on
that behavior, but if there is someone then we'll need to figure out
how to enable (or disable) this new delayed behavior selectively.
- In order for this to work we now have a hard dependency on
"PM". From memory this is a legit thing to assume these days and we
don't have to find some fallback to keep working if someone wants to
build their system without "PM".
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210416153909.v4.7.I9e8bd33b49c496745bfac58ea9ab418bd3b6f5ce@changeid
msm-next pull request has a baseline with stuff from -fixes, roll
forward first.
Some simple conflicts in amdgpu, ttm and one in i915 where git gets
confused and tries to add the same function twice.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fix the following coccicheck warning:
drivers/gpu/drm/panel//panel-tpo-td043mtea1.c:217:8-16: WARNING:
use scnprintf or sprintf
drivers/gpu/drm/panel//panel-tpo-td043mtea1.c:189:8-16: WARNING:
use scnprintf or sprintf
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1617069288-8317-1-git-send-email-tiantao6@hisilicon.com
Disable TE for Droid 4 panel, since implementation is currently
broken. Also disable it for N950 panel, which is untested.
Reported-by: Tony Lindgren <tony@atomide.com>
Reported-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Fixes: 4c1b935fea ("drm/omap: dsi: move TE GPIO handling into core")
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210227214542.99961-1-sebastian.reichel@collabora.com
Noralf needs some patches in 5.12-rc3, and we've been delaying the 5.12
merge due to the swap issue so it looks like a good time.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Panel power sequence says timing T8 (time from link idle to turn on
the backlight) should be at least 50 ms. This is what the .enable
delay in simple-panel is for, so set it. NOTE: this overlaps with the
80 ms .prepare_to_enable delay on purpose. The data sheet says that
at least 80 ms needs to pass between HPD going high and turning on the
backlight and that at least 50 ms needs to pass between the link idle
and the backlight going on. Thus it works like this on the system in
front of me:
* In bridge chip pre_enable call drm_panel_prepare()
* drm_panel_prepare() -> panel_simple_prepare()
* Wait for HPD GPIO to go high.
* Start counting for 80 ms (store in prepared_time)
* In bridge chip enable, train link then call drm_panel_enable()
* drm_panel_enable() -> panel_simple_enable()
* panel_simple_enable() does hardcoded 50 ms delay then enforces 80 ms
from HPD going high (in case the bridge took less than 30 ms to
enable / link train).
* drm_panel_enable() -> backlight_enable().
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210222081716.1.I1a45aece5d2ac6a2e73bbec50da2086e43e0862b@changeid
This panel is quite similar to the similarly named N116BGE panel (the
nominal timings are, in fact identical). However, let's add a new
entry because the full range of clocks listed for N116BGE aren't
supported for N116BCA-EA1, at least according to the datasheet.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210115144345.v2.5.I3c01f3aab8335cb509da7009d8938c1a27a266dc@changeid
On an Innolux N116BCA panel that I have in front of me, sometimes HPD
simply doesn't assert no matter how long you wait for it. As per the
very wise advice of The IT Crowd ("Have you tried turning it off and
on again?") it appears that power cycling is enough to kick this panel
back into a sane state.
>From tests on this panel, it appears that leaving it powered off for a
while stimulates the problem. Adding a 6 second sleep at the start of
panel_simple_prepare_once() makes it happen fairly reliably and, with
this delay, I saw up to 3 retries needed sometimes. Without the 6
second sleep, however, the panel came up much more reliably the first
time or after only 1 retry.
While it's unknown what the problems are with this panel (and probably
the hardware should be debugged), adding a few retries to the power on
routine doesn't seem insane. Even if this panel's problems are
attributed to the fact that it's pre-production and/or can be fixed,
retries clearly can help in some cases and really don't hurt.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210115144345.v2.3.I6916959daa7c5c915e889442268d23338de17923@changeid
If a panel has an hpd_absent_delay specified then we know exactly how
long the maximum time is before HPD must be asserted. That means we
can use it as a timeout for polling the HPD pin instead of using an
arbitrary timeout. This is especially useful for dealing with panels
that periodically fail to power on and need to be retried. We can
detect the problem sooner.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210115144345.v2.2.I183b1817610d7a82fdd3bc852e96d2985df9623f@changeid
If the HPD signal never asserts in panel_simple_prepare() and we
return an error, we should unset the enable GPIO and disable the
regulator to make it consistent for the caller.
At the moment I have some hardware where HPD sometimes doesn't assert.
Obviously that needs to be debugged, but this patch makes it so that
if I add a retry that I can make things work.
Fixes: 48834e6084 ("drm/panel-simple: Support hpd-gpios for delaying prepare()")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210115144345.v2.1.I33fcbd64ab409cfe4f9491bf449f51925a4d3281@changeid
A recent patch renaming MIPI_DSI_MODE_EOT_PACKET to
MIPI_DSI_MODE_NO_EOT_PACKET brought to light the
misunderstanding in the current MCDE driver and all
its associated panel drivers that MIPI_DSI_MODE_EOT_PACKET
would mean "use EOT packet" when in fact it means the
reverse.
Fix it up by implementing the flag right in the MCDE
DSI driver and remove the flag from panels that actually
want the EOT packet.
Suggested-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Fixes: 5fc537bfd0 ("drm/mcde: Add new driver for ST-Ericsson MCDE")
Fixes: 899f24ed8d ("drm/panel: Add driver for Novatek NT35510-based panels")
Fixes: ac1d6d7488 ("drm/panel: Add driver for Samsung S6D16D0 panel")
Fixes: 435e06c06c ("drm/panel: s6e63m0: Add DSI transport")
Fixes: 8152c2bfd7 ("drm/panel: Add driver for Sony ACX424AKP panel")
Link: https://patchwork.freedesktop.org/patch/msgid/20210304004138.1785057-1-linus.walleij@linaro.org
The panel is able to work when dsi clock is non-continuous, thus
the system power consumption can be reduced using such feature.
Add MIPI_DSI_CLOCK_NON_CONTINUOUS to panel's mode_flags.
Also the flag actually becomes necessary after
commit c6d94e37bd ("drm/bridge/synopsys: dsi: add support for non-continuous HS clock")
and without it the panel only emits stripes instead of output.
Fixes: c6d94e37bd ("drm/bridge/synopsys: dsi: add support for non-continuous HS clock")
Cc: stable@vger.kernel.org # 5.10+
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Christopher Morgan <macromorgan@hotmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210206135020.1991820-1-heiko@sntech.de
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
The "max-brightness" is a standard backlight property that
we need to support for the Samsung GT-I8190 Golden because
the display will go black if we crank up the brightness
too high.
As the platform needs this ability to give picture this is
a regression fix along with the addition of the property
to the GT-I8190 device tree.
Cc: Stephan Gerhold <stephan@gerhold.net>
Fixes: 9c3f0a0dd6 ("drm/panel: s6e63m0: Implement 28 backlight levels")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20201214222210.238081-1-linus.walleij@linaro.org
Add a panel database to the driver instead of reading propertes from DT
data. This is similar to panel-simple, and I believe it's more future
safe way to handle the panels.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201215104657.802264-73-tomi.valkeinen@ti.com
We have a useless 'if' in the dsicm_bl_update_status(), a left over from
the conversion to DRM model. Drop the if.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201215104657.802264-72-tomi.valkeinen@ti.com
Set the column & page address once during setup, instead of relying the
DSI host driver to set those.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201215104657.802264-61-tomi.valkeinen@ti.com
Simplify the code by moving code from _dsicm_enable_te() into
dsicm_power_on().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201215104657.802264-57-tomi.valkeinen@ti.com
Use the common MIPI_DCS_GET_ERROR_COUNT_ON_DSI define instead of
driver's own.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201215104657.802264-56-tomi.valkeinen@ti.com
The panel driver is no longer using any OMAP specific APIs, so
let's move it into the generic panel directory.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201215104657.802264-40-tomi.valkeinen@ti.com
