If an error was detected when CMD23 was issued, command sequence should
be terminated with errors and CMD23 should be issued after retuning.
Fixes: 8b22c3c18b ("mmc: tmio: add CMD23 support")
Signed-off-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: <stable@vger.kernel.org> # 4.13+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
TMIO_MASK_CMD is properly enabled in tmio_mmc_start_command().
We have no reason to set it up in tmio_mmc_host_probe(). (If we
really wanted to set it in the probe, we would have to do likewise
when resuming.)
Even worse, the following code is extremely confusing:
_host->sdcard_irq_mask &= ~irq_mask;
The logic is opposite between "->sdcard_irq_mask" and "irq_mask".
The intention is not clear at a glance.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently, force_pio is cleared when the driver exits. Then, it
resulted in clearing it in multiple places since MMC drivers in
general have multiple exit points.
tmio_mmc_reset_work - bails out on timeout
tmio_process_mrq - error out when it cannot send a command
tmio_mmc_finish_request - successful exit
This is error-prone since we may miss to cover all bail-out points.
To simplify the code, the data structure should be initialized just
before used since we have a single entrance. force_pio is only used
for data transfer, so tmio_mmc_start_data() will be a suitable place
to clear this flag.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As far as I tested the IP on UniPhier SoCs, TMIO_STAT_{RXRDY,TXRQ}
are asserted for DMA mode as well as for PIO. I need to disable the
those IRQs in dma_ops->start hook, otherwise the DMA transfer fails
with the following error message:
PIO IRQ in DMA mode!
Renesas chips are the same cases since I see their dma_ops->start
hooks explicitly clear TMIO_STAT_{RXRDY,TXRQ} (with nice comment!).
If we do this sanity check in TMIO MMC core, RXRDY/TXRQ handling
should be entirely moved to the core. tmio_mmc_cmd_irq() will
be a suitable place to disable them.
The probe function sets TMIO_MASK_{READOP,WRITEOP} but this is odd.
/* Unmask the IRQs we want to know about */
if (!_host->chan_rx)
irq_mask |= TMIO_MASK_READOP;
if (!_host->chan_tx)
irq_mask |= TMIO_MASK_WRITEOP;
At this point, _host->{chan_rx,chan_tx} are _always_ NULL because
tmio_mmc_request_dma() is called after this code. Consequently,
TMIO_MASK_{READOP,WRITEOP} are set here whether DMA is used or not.
Remove this pointless code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
The TMIO mmc cannot detect the card insertion in native_hotplug mode
if the driver is probed without a card inserted.
The reason is obvious; all IRQs are disabled by tmio_mmc_host_probe(),
as follows:
tmio_mmc_disable_mmc_irqs(_host, TMIO_MASK_ALL);
The card event IRQs are first enabled by tmio_mmc_start_command() as
follows:
if (!host->native_hotplug)
irq_mask &= ~(TMIO_STAT_CARD_REMOVE | TMIO_STAT_CARD_INSERT);
tmio_mmc_enable_mmc_irqs(host, irq_mask);
If the driver is probed without a card, tmio_mmc_start_command() is
never called in the first place. So, the card is never detected.
The card event IRQs must be enabled in probe/resume functions.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
A card detect GPIO is set up only for platforms with "cd-gpios"
DT property or TMIO_MMC_USE_GPIO_CD flag. However, the driver
core always uses mmc_gpio_get_cd, which just fails with -ENOSYS
if ctx->cd_gpio is unset.
The bit 5 of the status register provides the current signal level
of the CD line. Allow to use it if the GPIO is unused.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
This property is equivalent to "disable-wp" defined in
Documentation/devicetree/bindings/mmc/mmc.txt
The TMIO MMC core calls mmc_of_parse(), and it sets
MMC_CAP2_NO_WRITE_PROTECT if "disable-wp" property is present.
We do not need a vendor-specific property to do the same thing.
Let's remove the description from the dt-binding to prevent new boards
from using it.
I am keeping the driver code for existing DT files, but added
comments that this is deprecated.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
The use of this flag has been replaced with MMC_CAP2_NO_WRITE_PROTECT.
No platform defines this flag any more. Remove.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
TMIO_MMC_WRPROTECT_DISABLE is equivalent to MMC_CAP2_NO_WRITE_PROTECT.
Only the difference is the TMIO_... makes tmio_mmc_get_ro() return 0
(i.e. it does not affect mmc_gpio_get_ro() at all), while MMC_CAP2_...
returns 0 before calling ->get_ro() hook (i.e. it affects both IP own
logic and GPIO detection).
The TMIO MMC drivers do not set-up gpio_ro by themselves. Only the
possibility, if any, would be DT specifies "wp-gpios" property, and
gpio_ro is set by mmc_gpiod_request_ro() called from mmc_of_parse().
However, it does not make sense to specify "wp-gpios" property and
"toshiba,mmc-wrprotect-disable" at the same time.
I checked under arch/arm/boot/dts/ and arch/arm64/boot/dts/renesas/,
and I did not see any Renesas boards with "wp-gpios". So, this
conversion should be safe.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
When CONFIG_PM is disabled, we get a warning about the clock handling
being unused:
drivers/mmc/host/tmio_mmc_core.c:937:13: error: 'tmio_mmc_clk_disable' defined but not used [-Werror=unused-function]
static void tmio_mmc_clk_disable(struct tmio_mmc_host *host)
^~~~~~~~~~~~~~~~~~~~
drivers/mmc/host/tmio_mmc_core.c:929:12: error: 'tmio_mmc_clk_enable' defined but not used [-Werror=unused-function]
static int tmio_mmc_clk_enable(struct tmio_mmc_host *host)
^~~~~~~~~~~~~~~~~~~
As the clock handling is now done elsewhere, this is only used when
power management is enabled. We could make the functions as __maybe_unused,
but since there is already an #ifdef section, it seems easier to move
the helpers closer to their callers.
Fixes: b21fc29438 ("mmc: tmio: move clk_enable/disable out of tmio_mmc_host_probe()")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This IP provides the write protect signal level in the status
register, but it is also possible to use GPIO for WP. They are
exclusive, so it is not efficient to call mmc_gpio_get_ro() every
time from tmio_mmc_get_ro() if we know gpio_ro is not used.
Check the capability of gpio_ro just once in the probe function,
then set mmc_gpio_get_ro to .get_ro if it is the case.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Drivers need to set up various struct members for tmio_mmc_host before
calling tmio_mmc_host_probe(). Do likewise for host->dma_ops instead
of passing it as a function argument.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_of_parse() parses various DT properties and sets capability flags
accordingly. However, drivers have no chance to run platform init
code depending on such flags because mmc_of_parse() is called from
tmio_mmc_host_probe().
Move mmc_of_parse() to tmio_mmc_host_alloc() so that drivers can
handle capabilities before mmc_add_host(). Move tmio_mmc_of_parse()
likewise.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The clock is enabled in the tmio_mmc_host_probe(). It also prevents
drivers from performing platform-specific settings before mmc_add_host()
because the register access generally requires a clock.
Enable/disable the clock in drivers' probe/remove. Also, I passed
tmio_mmc_data to tmio_mmc_host_alloc() because renesas_sdhi_clk_enable()
needs it to get the private data from tmio_mmc_host.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The register region is ioremap'ed in the tmio_mmc_host_probe(), i.e.
drivers cannot get access to the hardware before mmc_add_host().
Actually, renesas_sdhi_core.c reads out the CTL_VERSION register to
complete the platform-specific settings. However, at this point,
the MMC host is already running.
Move the register ioremap to tmio_mmc_host_alloc() so that drivers
can perform platform-specific settings between tmio_mmc_host_alloc()
and tmio_mmc_host_probe().
I changed tmio_mmc_host_alloc() to return an error pointer to
propagate the return code from devm_ioremap_resource().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To use a GPIO line for card detection, TMIO_MMC_USE_GPIO_CD is set
by a legacy board (arch/sh/boards/mach-ecovec24).
For DT platforms, the "cd-gpios" property is a legitimate way for that
in case the IP-builtin card detection can not be used for some reason.
mmc_of_parse() calls mmc_gpiod_request_cd() to set up ctx->cd_gpio if
the "cd-gpios" property is specified.
To cater to both cases, mmc_can_gpio_cd() is a correct way to check
which card detection logic is used.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Drivers do not need to call mmc_gpiod_request_cd_irq() explicitly
because mmc_start_host() calls it. To make it work, cd_gpio must
be set before mmc_add_host().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Drivers can set any mmc_host_ops hooks between tmio_mmc_host_alloc()
and tmio_mmc_host_probe(). Remove duplicated hooks in tmio_mmc_host.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently, tmio_mmc_ops is static data and tmio_mmc_host_probe()
updates some hooks in the static data. This is a problem when
two or more instances call tmio_mmc_host_probe() and each of them
requests to use its own card_busy/start_signal_voltage_switch.
We can borrow a solution from sdhci_alloc_host(). Copy the whole
ops structure to host->mmc_host_ops, then override the hooks in
malloc'ed data. Constify tmio_mmc_ops since it is now a template
ops used by default.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The TMIO core misses to call request_mem_region().
devm_ioremap_resource() takes care of it and makes the code cleaner.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The remove, suspend, resume hooks need to get tmio_mmc_host. It is
tedious to call mmc_priv() to convert mmc_host to tmio_mmc_host.
We can directly set tmio_mmc_host to driver data.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There are a few udelay() left which are in a range that they should be
usleep_range() these days.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As documented in Documentation/timers/timers-howto.txt
as follows, replace msleep() with usleep_range().
msleep(1~20) may not do what the caller intends, and
will often sleep longer (~20 ms actual sleep for any
value given in the 1~20ms range). In many cases this
is not the desired behavior.
Signed-off-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* Add a jump target so that a bit of exception handling can be better
reused at the end of this function.
* Adjust condition checks.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_regulator_get_supply returns -EPROBE_DEFER if either vmmc or
vqmmc regulators had their probing deferred.
vqmmc regulator is needed by UHS to work properly, therefore this
patch checks the value returned by mmc_regulator_get_supply to
make sure we have a reference to both vmmc and vqmmc (if found in
the DT).
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since the commit de3ee99b09 ("mmc: Delete bounce buffer handling")
deletes the bounce buffer handling, a request data size will be referred
to max_{req,seg}_size instead of MMC_QUEUE_BOUNCESZ (64k bytes).
In other hand, renesas_sdhi_internal_dmac.c will set very big value of
max_{req,seg}_size because the max_blk_count is set to 0xffffffff.
And then, "swiotlb buffer is full" happens because swiotlb can handle
a memory size up to 256k bytes only (IO_TLB_SEGSIZE = 128 and
IO_TLB_SHIFT = 11).
So, as a workaround, this patch avoids the issue by setting
the max_{req,seg}_size up to 256k bytes if swiotlb is running.
Reported-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some change for v4.14 broke the debug output for TMIO. But since it was
not helpful to me and too noisy for my taste anyhow, let's just remove
it instead of fixing it. We'll find something better if we'd need it...
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Our hardware engineers confirmed that it is unnecessary to wait when
turning the clock on/off. The documentation was a tad vague, so we
used to play safe.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
I always anticipated this code to be not correct, but now I had a test
case to prove it. According to all documentation I have, setting the
TMIO_STOP_STP bit ever only worked during block transfers. This bit is
like manually enforcing an autocmd12 during a so far seamless transfer.
It does NOT work when the block transfer had errors. It also does NOT
work with any other cmd except block commands. For all those, CMD12 has
to be treated like any other command. So, basically, we could use this
bit only for mrq->data->stop cmds. But for these, we happily use the
autocmd12 feature using the TMIO_STOP_SEC bit. As a result, the above
bit is not useful for us and we need to treat CMD12 as a regular cmd
always. Just remove the special handling code. Note that the BSP
recognized this issue as well yet had a more cautious solution to the
problem [1]. Which is understandable but makes CMD12 handling even more
complicated.
Checked with a Renesas Salvator-X/M3-W which needed to send CMD12 when
retuning one of my SD cards.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas-bsp.git/commit/?id=2838a2ff8ca776f6d18b7fbbe75f3df8dd64183a
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Jan Klötzke <jan.kloetzke@preh.de>
Tested-by: Nguyen Viet Dung <dung.nguyen.aj@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add dataend to DMA ops to allow DMAC implementation dependent
handling of DMA data end.
Also implement the operation for SDHI.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Allow TMIO and SDHI driver implementations to provide values for
max_segs and max_blk_count.
A follow-up patch will set these values for Renesas Gen3 SoCs
the using an SDHI driver.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Ai Kyuse <ai.kyuse.uw@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The existing code gives an incorrect pointer value.
The buffer pointer 'buf' was of type unsigned short *, and 'count' was a
number in bytes. A cast of buf should have been used.
However, instead of casting, just change the code to use u32 pointers.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 8185e51f35: ("mmc: tmio-mmc: add support for 32bit data port")
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Update copyrights to reflect work by Wolfram Sang and myself since last
year.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use EXPORT_SYMBOL_GPL rather than the non _GPL variant as there seems to be
no reason not to.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To achieve that, we set the registers in the generic HW reset routine
which gets called at both, init and resume. We also make sure to move
SDIO initialization before reset gets called in probe().
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Plain code move with no changes. Needed for refactoring. Also, looks
nicer if request and finish_request are next to each other.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The obviously wrong comment was added in 2011 with commit df3ef2d3c9
("mmc: protect the tmio_mmc driver against a theoretical race") but
already obsoleted half a year later with commit b9269fdd4f ("mmc:
tmio: fix recursive spinlock, don't schedule with interrupts disabled").
Fixes: b9269fdd4f ("mmc: tmio: fix recursive spinlock, don't schedule with interrupts disabled")
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Split handling mrq into a seperate function. We need to call it from
another place soon.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This part confused me and I had to read it twice until I got it. Let's
follow the standard pattern to bail out if something is wrong and keep
in the body of the function when everything is as expected.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Rename tmio_mmc_pio.c to tmio_mmc_core.c to more accurately reflect its
function: to provide core code for the tmio-mmc and sh-mobole-sdhi drivers.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
