The SKB for a Tx packet is associated with an xgbe_ring_data structure
in the xgbe_map_tx_skb function. However, it is being saved in the
structure after the last structure used when the SKB is mapped. Use
the last used structure to save the SKB value.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupt value within the xgbe_ring_data structure is used as an
indicator of which Rx descriptor should have the INTE bit set to
generate an interrupt when that Rx descriptor is used. This bit was
mistakenly cleared in the xgbe_unmap_rdata function, effectively
nullifying the ethtool rx-frames support.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mvneta_tx() dereferences skb to get skb->len too late,
as hardware might have completed the transmit and TX completion
could have freed the skb from another cpu.
Fixes: 71f6d1b31f ("net: mvneta: replace Tx timer with a real interrupt")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvneta driver sets the amount of Tx coalesce packets to 16 by
default. Normally that does not cause any trouble since the driver
uses a much larger Tx ring size (532 packets). But some sockets
might run with very small buffers, much smaller than the equivalent
of 16 packets. This is what ping is doing for example, by setting
SNDBUF to 324 bytes rounded up to 2kB by the kernel.
The problem is that there is no documented method to force a specific
packet to emit an interrupt (eg: the last of the ring) nor is it
possible to make the NIC emit an interrupt after a given delay.
In this case, it causes trouble, because when ping sends packets over
its raw socket, the few first packets leave the system, and the first
15 packets will be emitted without an IRQ being generated, so without
the skbs being freed. And since the socket's buffer is small, there's
no way to reach that amount of packets, and the ping ends up with
"send: no buffer available" after sending 6 packets. Running with 3
instances of ping in parallel is enough to hide the problem, because
with 6 packets per instance, that's 18 packets total, which is enough
to grant a Tx interrupt before all are sent.
The original driver in the LSP kernel worked around this design flaw
by using a software timer to clean up the Tx descriptors. This timer
was slow and caused terrible network performance on some Tx-bound
workloads (such as routing) but was enough to make tools like ping
work correctly.
Instead here, we simply set the packet counts before interrupt to 1.
This ensures that each packet sent will produce an interrupt. NAPI
takes care of coalescing interrupts since the interrupt is disabled
once generated.
No measurable performance impact nor CPU usage were observed on small
nor large packets, including when saturating the link on Tx, and this
fixes tools like ping which rely on too small a send buffer. If one
wants to increase this value for certain workloads where it is safe
to do so, "ethtool -C $dev tx-frames" will override this default
setting.
This fix needs to be applied to stable kernels starting with 3.10.
Tested-By: Maggie Mae Roxas <maggie.mae.roxas@gmail.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
In sky2_change_mtu setting B0_IMSK to 0 may be delayed due to PCI write posting
which could result in irqs being still active when synchronize_irq is called.
Since we are not prepared to handle any further irqs after synchronize_irq
(our resources are freed after that) force the write by a consecutive read from
the same register.
Similar situation in sky2_all_down: Here we disabled irqs by a write to B0_IMSK
but did not ensure that this write took place before synchronize_irq. Fix that
too.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of a spurious interrupt dont forget to reenable the interrupts that
have been masked by reading the interrupt source register.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Acked-by: Mirko Lindner <mlindner@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In pxa168_eth_open() the irqs are enabled before napi. This opens a tiny time
window in which the irq handler is processed, disables irqs but then is not able
to schedule the not yet activated napi, leaving irqs disabled forever (since
irqs are reenabled in napi poll function).
Fix this race by activating napi before irqs are activated.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Original code only check/alloc plat_dat for the CONFIG_OF case, this
patch check/alloc it earlier and unconditionally to avoid kernel build
warnings:
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c:275
stmmac_pltfr_probe() warn: variable dereferenced before check 'plat_dat'
V2: Fix coding style.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current driver, allocation size of skb does not care the alignment
adjust after allocation.
And also, in the current implementation, buffer alignment method by
sh_eth_set_receive_align function has a bug that this function displace
buffer start address forcedly when the alignment is corrected.
In the result, tail of the skb will exceed allocated area and kernel panic
will be occurred.
This patch fix this issue.
Signed-off-by: Mitsuhiro Kimura <mitsuhiro.kimura.kc@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ndo_bridge_setlink() is currently only called on the slave if
IFLA_AF_SPEC is set but this is a very fragile assumption and may
change in the future.
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Payload is currently accessed blindly and may exceed valid message
boundaries.
Fixes: a77dcb8c8 ("be2net: set and query VEB/VEPA mode of the PF interface")
Fixes: 815cccbf1 ("ixgbe: add setlink, getlink support to ixgbe and ixgbevf")
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 3b57de958e brought the support for a different amount of
the filter bins, but didn't update the platform driver that without
CONFIG_OF.
Fixes: 3b57de958e (net: stmmac: Support devicetree configs for mcast
and ucast filter entries)
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some VF drivers use the upper byte of "param1" (the qp count field)
in mlx4_qp_reserve_range() to pass flags which are used to optimize
the range allocation.
Under the current code, if any of these flags are set, the 32-bit
count field yields a count greater than 2^24, which is out of range,
and this VF fails.
As these flags represent a "best-effort" allocation hint anyway, they may
safely be ignored. Therefore, the PF driver may simply mask out the bits.
Fixes: c82e9aa0a8 "mlx4_core: resource tracking for HCA resources used by guests"
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If TX channels are set to 4 and RX channels are set to less than 4,
using ethtool -L, the driver will try to initialize more RX channels
than it has allocated, causing an oops.
This fix only initializes the RX ring if it has been allocated.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds some checks in order to prevent panic's on surprise
removal of devices during S0, S3, S4. Without this patch, Thunderbolt
type device removal will panic the system.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While working on a different issue, I noticed an annoying use
after free bug on my machine when unloading the ixgbe driver:
[ 8642.318797] ixgbe 0000:02:00.1: removed PHC on p2p2
[ 8642.742716] ixgbe 0000:02:00.1: complete
[ 8642.743784] BUG: unable to handle kernel paging request at ffff8807d3740a90
[ 8642.744828] IP: [<ffffffffa01c77dc>] ixgbe_remove+0xfc/0x1b0 [ixgbe]
[ 8642.745886] PGD 20c6067 PUD 81c1f6067 PMD 81c15a067 PTE 80000007d3740060
[ 8642.746956] Oops: 0002 [#1] SMP DEBUG_PAGEALLOC
[ 8642.748039] Modules linked in: [...]
[ 8642.752929] CPU: 1 PID: 1225 Comm: rmmod Not tainted 3.18.0-rc2+ #49
[ 8642.754203] Hardware name: Supermicro X10SLM-F/X10SLM-F, BIOS 1.1b 11/01/2013
[ 8642.755505] task: ffff8807e34d3fe0 ti: ffff8807b7204000 task.ti: ffff8807b7204000
[ 8642.756831] RIP: 0010:[<ffffffffa01c77dc>] [<ffffffffa01c77dc>] ixgbe_remove+0xfc/0x1b0 [ixgbe]
[...]
[ 8642.774335] Stack:
[ 8642.775805] ffff8807ee824098 ffff8807ee824098 ffffffffa01f3000 ffff8807ee824000
[ 8642.777326] ffff8807b7207e18 ffffffff8137720f ffff8807ee824098 ffff8807ee824098
[ 8642.778848] ffffffffa01f3068 ffff8807ee8240f8 ffff8807b7207e38 ffffffff8144180f
[ 8642.780365] Call Trace:
[ 8642.781869] [<ffffffff8137720f>] pci_device_remove+0x3f/0xc0
[ 8642.783395] [<ffffffff8144180f>] __device_release_driver+0x7f/0xf0
[ 8642.784876] [<ffffffff814421f8>] driver_detach+0xb8/0xc0
[ 8642.786352] [<ffffffff814414a9>] bus_remove_driver+0x59/0xe0
[ 8642.787783] [<ffffffff814429d0>] driver_unregister+0x30/0x70
[ 8642.789202] [<ffffffff81375c65>] pci_unregister_driver+0x25/0xa0
[ 8642.790657] [<ffffffffa01eb38e>] ixgbe_exit_module+0x1c/0xc8e [ixgbe]
[ 8642.792064] [<ffffffff810f93a2>] SyS_delete_module+0x132/0x1c0
[ 8642.793450] [<ffffffff81012c61>] ? do_notify_resume+0x61/0xa0
[ 8642.794837] [<ffffffff816d2029>] system_call_fastpath+0x12/0x17
The issue is that test_and_set_bit() done on adapter->state is being
performed *after* the netdevice has been freed via free_netdev().
When netdev is being allocated on initialization time, it allocates
a private area, here struct ixgbe_adapter, that resides after the
net_device structure. In ixgbe_probe(), the device init routine,
we set up the adapter after alloc_etherdev_mq() on the private area
and add a reference for the pci_dev as well via pci_set_drvdata().
Both in the error path of ixgbe_probe(), but also on module unload
when ixgbe_remove() is being called, commit 41c62843eb ("ixgbe:
Fix rcu warnings induced by LER") accesses adapter after free_netdev().
The patch stores the result in a bool and thus fixes above oops on my
side.
Fixes: 41c62843eb ("ixgbe: Fix rcu warnings induced by LER")
Cc: stable <stable@vger.kernel.org>
Cc: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IXGBE adapter seems to require that VLAN filtering be enabled if
VMDQ or SRIOV are enabled. When those functions are disabled,
VLAN filtering may be disabled in promiscuous mode.
Prior to commit a9b8943ee1 ("ixgbe: remove vlan_filter_disable
and enable functions")
The logic was correct. However, after the commit the logic
got reversed and VLAN filtered in now turned on when VMDQ/SRIOV
is disabled.
This patch changes the condition to enable hw vlan filtered
when VMDQ or SRIOV is enabled.
Fixes: a9b8943ee1 ("ixgbe: remove vlan_filter_disable and enable functions")
Cc: stable <stable@vger.kernel.org>
CC: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Acked-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Peer priority groups were being reversed, but this was missed in the previous
fix sent out for this issue.
v2 : Previous patch was doing extra unnecessary work, result is the same.
Please ignore previous patch
Fixes : ee7bc3cdc2 ('cxgb4 : dcb open-lldp interop fixes')
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is currently missing, which results in a crash when one attempts
to set VXLAN tunnel over the mlx4_en when acting as PF.
[ 2408.785472] BUG: unable to handle kernel NULL pointer dereference at (null)
[...]
[ 2408.994104] Call Trace:
[ 2408.996584] [<ffffffffa021f7f5>] ? vxlan_get_rx_port+0xd6/0x103 [vxlan]
[ 2409.003316] [<ffffffffa021f71f>] ? vxlan_lowerdev_event+0xf2/0xf2 [vxlan]
[ 2409.010225] [<ffffffffa0630358>] mlx4_en_start_port+0x862/0x96a [mlx4_en]
[ 2409.017132] [<ffffffffa063070f>] mlx4_en_open+0x17f/0x1b8 [mlx4_en]
While here, make sure to invoke vxlan_get_rx_port() only when VXLAN
offloads are actually enabled and not when they are only supported.
Reported-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TX_IN_SEL offset for the CPSW_PORT/TX_IN_CTL register was
incorrect. This caused the Dual MAC mode to never get set when
it should. It also caused possible unintentional setting of a
bit in the CPSW_PORT/TX_BLKS_REM register.
The purpose of setting the Dual MAC mode for this register is to:
"... allow packets from both ethernet ports to be written into
the FIFO without one port starving the other port."
- AM335x ARM TRM
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use vxlan_gso_check() to advertise offload support for this NIC.
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Acked-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use vxlan_gso_check() to advertise offload support for this NIC.
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use vxlan_gso_check() to advertise offload support for this NIC.
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Acked-by: Sathya Perla <sperla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With commit be9dad1f9f ("net: phy: suspend phydev when going
to HALTED"), the PHY device will be put in a low-power mode using
BMCR_PDOWN if the the interface is set down. The smsc911x driver does
a software_reset opening the device driver (ndo_open). In such case,
the PHY must be powered-up before access to any register and before
calling the software_reset function. Otherwise, as the PHY is powered
down the software reset fails and the interface can not be enabled
again.
This patch fixes this scenario that is easy to reproduce setting down
the network interface and setting up again.
$ ifconfig eth0 down
$ ifconfig eth0 up
ifconfig: SIOCSIFFLAGS: Input/output error
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Increased delay in the smsc911x_phy_disable_energy_detect (from 1ms to 2ms).
Dropped delays in the smsc911x_phy_enable_energy_detect (100ms and 1ms).
The patch affect SMSC LAN generation 4 chips with integrated PHY (LAN9221).
I saw problems with soft reset due to wrong udelay timings.
After I fixed udelay, I measured the time needed to bring integrated PHY
from power-down to operational mode (the time beetween clearing EDPWRDOWN
bit and soft reset complete event). I got 1ms (measured using ktime_get).
The value is equal to the current value (1ms) used in the
smsc911x_phy_disable_energy_detect. It is near the upper bound and in order
to avoid rare soft reset faults it is doubled (2ms).
I don't know official timing for bringing up integrated PHY as specs doesn't
clarify this (or may be I didn't found).
It looks safe to drop delays before and after setting EDPWRDOWN bit
(enable PHY power-down mode). I didn't saw any regressions with the patch.
The patch was reviewed by Steve Glendinning and Microchip Team.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Acked-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch affect SMSC LAN generation 4 chips with integrated PHY (LAN9221).
It is possible that PHY could enter power-down mode (ENERGYON clear),
between ENERGYON bit check in smsc911x_phy_disable_energy_detect and SRST
bit set in smsc911x_soft_reset. This could happen, for example, if someone
disconnect ethernet cable between the checks. The PHY in a power-down mode
would prevent the MAC portion of chip to be software reseted.
Initially found by code review, confirmed later using test case.
This is low probability issue, and in order to reproduce it you have to
run the script:
while true; do
ifconfig eth0 down
ifconfig eth0 up || break
done
While the script is running you have to plug/unplug ethernet cable many
times (using gpio controlled ethernet switch, for example) until get:
[ 4516.477783] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 4516.512207] smsc911x smsc911x.0: eth0: SMSC911x/921x identified at 0xce006000, IRQ: 336
[ 4516.524658] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 4516.559082] smsc911x smsc911x.0: eth0: SMSC911x/921x identified at 0xce006000, IRQ: 336
[ 4516.571990] ADDRCONF(NETDEV_UP): eth0: link is not ready
ifconfig: SIOCSIFFLAGS: Input/output error
The patch was reviewed by Steve Glendinning and Microchip Team.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Acked-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit ae5c6c6d "ptp: Classify ptp over ip over vlan packets" changed the
code in two drivers that matches time stamps with PTP frames, with the goal
of allowing VLAN tagged PTP packets to receive hardware time stamps.
However, that commit failed to account for the VLAN header when parsing
IPv4 packets. This patch fixes those two drivers to correctly match VLAN
tagged IPv4/UDP PTP messages with their time stamps.
This patch should also be applied to v3.17.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* In LLD_MANAGED mode, traffic classes were being returned in reverse order to
lldp agent.
* Priotype of strict is no longer the default returned.
* Change behaviour of getdcbx() based on discussions on lldp-devel
These were missed as there was no working fetch interface for open-lldp when
running in LLD_MANAGED mode till now.
Fixes: 76bcb31efc ("cxgb4 : Add DCBx support codebase and dcbnl_ops")
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case an interface has been brought down before entering S3, and then
brought up out of S3, all the initialization done during
bcmgenet_probe() by bcmgenet_mii_init() calling bcmgenet_mii_config() is
just lost since register contents are restored to their reset values.
Re-apply this configuration anytime we call bcmgenet_open() to make sure
our port multiplexer is properly configured to match the PHY interface.
Since we are now calling bcmgenet_mii_config() everytime bcmgenet_open()
is called, make sure we only print the message during initialization
time not to pollute the console.
Fixes: b6e978e504 ("net: bcmgenet: add suspend/resume callbacks")
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_disconnect() is the only way to guarantee that we are not going to
schedule more work on the PHY state machine workqueue for that
particular PHY device.
This fixes an issue where a network interface was suspended prior to a
system suspend/resume cycle and would then be resumed as part of
mdio_bus_resume(), since the GENET interface clocks would have been
disabled, this basically resulted in bus errors to appear since we are
invoking the GENET driver adjust_link() callback.
Fixes: b6e978e504 ("net: bcmgenet: add suspend/resume callbacks")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the dependency of the VENDOR entry and fixes
the QCA7000 one.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Status variable is never initialized, can carry an arbitrary value
on the stack and thus may let the function fail.
Fixes: e90dd26456 ("ixgbe: Make return values more direct")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currenly we only support Large-Send and TX checksum offloads for
encapsulated traffic of type VXLAN. We must make sure to advertize
these offloads up to the stack only when VXLAN tunnel is set.
Failing to do so, would mislead the the networking stack to assume
that the driver can offload the internal TX checksum for GRE packets
and other buggy schemes.
Reported-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike CEE, IEEE has a bespoke app delete call and does not rely on priority
for app deletion
Fixes : 2376c879b8 ('cxgb4 : Improve handling of DCB negotiation or loss
thereof')
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Free List Starvation Threshold needs to be larger than the SGE's Egress
Congestion Threshold or we'll end up in a mutual stall where the driver waits
for Ingress Packets to drive replacing Free List Pointers and the SGE waits for
Free List Pointers before pushing Ingress Packets to the host.
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
T5 introduces the ability to have separate Packing and Padding Boundaries
for SGE DMA transfers from the chip to Host Memory. This change set takes
advantage of that to set up a smaller Padding Boundary to conserve PCI Link
and Memory Bandwidth with T5.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move fl_starv_thres into adapter->sge data structure since it
_could_ be different from adapter to adapter. Also move other per-adapter
SGE values which had been treated as driver globals into adapter->sge.
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 1b7bde6d65 ("net: fec: implement rx_copybreak to improve rx performance")
introduced a regression for i.MX28. The swap_buffer() function doing
the endian conversion of the received data on i.MX28 may access memory
beyond the actual packet size in the DMA buffer. fec_enet_copybreak()
does not copy those bytes, so that the last bytes of a packet may be
filled with invalid data after swapping.
This will likely lead to checksum errors on received packets.
E.g. when trying to mount an NFS rootfs:
UDP: bad checksum. From 192.168.1.225:111 to 192.168.100.73:44662 ulen 36
Do the byte swapping and copying to the new skb in one go if
necessary.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Poll for the link events only if firmware doesn't have capability
to notify the driver for the link events.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When events arrive at driver load, the event handler gets called even before
the spinlock and list are initialized. Fix this by moving the initialization
before EQs creation.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the EQ is created, it can possibly generate interrupts and the interrupt
handler is referencing eq->dev. It is therefore required to set eq->dev before
calling request_irq() so if an event is generated before request_irq() returns,
we will have a valid eq->dev field.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when cpsw is build as modulea and simple insert and removal of module
creates a deadlock, due to delete timer. the timer is created and destroyed
in cpsw_ale_start and cpsw_ale_stop which are from device open and close.
root@am437x-evm:~# modprobe -r ti_cpsw
[ 158.505333] INFO: trying to register non-static key.
[ 158.510623] the code is fine but needs lockdep annotation.
[ 158.516448] turning off the locking correctness validator.
[ 158.522282] CPU: 0 PID: 1339 Comm: modprobe Not tainted 3.14.23-00445-gd41c88f #44
[ 158.530359] [<c0015380>] (unwind_backtrace) from [<c0012088>] (show_stack+0x10/0x14)
[ 158.538603] [<c0012088>] (show_stack) from [<c054ad70>] (dump_stack+0x78/0x94)
[ 158.546295] [<c054ad70>] (dump_stack) from [<c0088008>] (__lock_acquire+0x176c/0x1b74)
[ 158.554711] [<c0088008>] (__lock_acquire) from [<c0088944>] (lock_acquire+0x9c/0x104)
[ 158.563043] [<c0088944>] (lock_acquire) from [<c004e520>] (del_timer_sync+0x44/0xd8)
[ 158.571289] [<c004e520>] (del_timer_sync) from [<bf2eac1c>] (cpsw_ale_destroy+0x10/0x3c [ti_cpsw])
[ 158.580821] [<bf2eac1c>] (cpsw_ale_destroy [ti_cpsw]) from [<bf2eb268>] (cpsw_remove+0x30/0xa0 [ti_cpsw])
[ 158.591000] [<bf2eb268>] (cpsw_remove [ti_cpsw]) from [<c035ef44>] (platform_drv_remove+0x18/0x1c)
[ 158.600527] [<c035ef44>] (platform_drv_remove) from [<c035d8bc>] (__device_release_driver+0x70/0xc8)
[ 158.610236] [<c035d8bc>] (__device_release_driver) from [<c035e0d4>] (driver_detach+0xb4/0xb8)
[ 158.619386] [<c035e0d4>] (driver_detach) from [<c035d6e4>] (bus_remove_driver+0x4c/0x90)
[ 158.627988] [<c035d6e4>] (bus_remove_driver) from [<c00af2a8>] (SyS_delete_module+0x10c/0x198)
[ 158.637144] [<c00af2a8>] (SyS_delete_module) from [<c000e580>] (ret_fast_syscall+0x0/0x48)
[ 179.524727] INFO: rcu_sched detected stalls on CPUs/tasks: {} (detected by 0, t=2102 jiffies, g=1487, c=1486, q=6)
[ 179.535741] INFO: Stall ended before state dump start
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ATM, txq_reclaim will dequeue and free an skb for each tx desc released
by the hw that has TX_LAST_DESC set. However, in case of TSO, each
hw desc embedding the last part of a segment has TX_LAST_DESC set,
losing the one-to-one 'last skb frag'/'TX_LAST_DESC set' correspondance,
which causes data corruption.
Fix this by checking TX_ENABLE_INTERRUPT instead of TX_LAST_DESC, and
warn when trying to dequeue from an empty txq (which can be symptomatic
of releasing skbs prematurely).
Fixes: 3ae8f4e0b9 ('net: mv643xx_eth: Implement software TSO')
Reported-by: Slawomir Gajzner <slawomir.gajzner@gmail.com>
Reported-by: Julien D'Ascenzio <jdascenzio@yahoo.fr>
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to fix the atomicity when suspend and resume the
driver. The clk api have been changed (as reported by Hao Liang)
and the skb allocation is done out of the hw setup function and
taking care about the GFP flags.
Reported-by: Hao Liang <hliang1025@gmail.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexey Khoroshilov <khoroshilov@ispras.ru>
Cc: Hao Liang <hliang1025@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch aims to fix the concurrency in eee initialization
inside the stmmac driver and related warnings when enable
DEBUG_ATOMIC_SLEEP.
Prior this patch, the stmmac_eee_init could be called in several places
as shown below:
stmmac_open stmmac_resume PHY Layer
| | |
stmmac_hw_setup stmmac_adjust_link
| | stmmac ethtool
|__________________________|______________|
|
stmmac_eee_init
The patch removes the stmmac_eee_init call inside the stmmac_hw_setup
that is unnecessary. It is sufficient to call it in the adjust_link to
always guarantee that EEE is always configured at mac level too.
Fixing the lock protection now it is covered another case (not
considered before). The stmmac_eee_init could be called by the ethtool
so critical sections must be protected inside this function too.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
