This patch renders the inlined gpio accessors in gpio.h independent of the
underlying controller's register layout. This is done by including three new
fields in davinci_gpio_controller to hold the addresses of the set, clear, and
in data registers.
Other changes:
1. davinci_gpio_regs structure definition moved to gpio.c. This structure is
no longer common across all davinci socs (davinci_gpio_controller is).
2. controller base address calculation code (gpio2controller()) moved to
gpio.c as this was no longer necessary for the inline implementation.
3. modified inline range checks to use davinci_soc_info.gpio_num instead of
DAVINCI_N_GPIO.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Tested-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Renamed gpio types to something more sensible:
struct gpio_controller --> struct davinci_gpio_regs
struct davinci_gpio --> struct davinci_gpio_controller
gpio2controller() --> gpio2regs()
irq2controller() --> irq2regs()
This change also moves davinci_gpio_controller definition to gpio.h.
Eventually, the gpio registers structure will be moved to gpio.c and no longer
a common cross-soc definition.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Tested-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Adds a macro to convert the GPIO signal passed as bank number
and signal to GPIO pin number.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
DA850/OMAP-L138 has 144 pins configurable as GPIO, but
currently this has been configured as 128. This patch
corrects it.
Also, this patch adds the base address for GPIO pins
greater than 128.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Support DM365 GPIOs ... primarily by handling non-banked GPIO IRQs:
- Flag DM365 chips as using non-banked GPIO interrupts, using a
new soc_info field.
- Replace the gpio_to_irq() mapping logic. This now uses some
runtime infrastructure, keyed off that new soc_info field,
which doesn't handle irq_to_gpio().
- Provide a new irq_chip ... GPIO IRQs handled directly by AINTC
still need edge triggering managed by the GPIO controller.
DM365 chips no longer falsely report 104 GPIO IRQs as they boot.
Intelligence about IRQ muxing is missing, so for the moment this
only exposes the first eight DM365 GPIOs, which are never muxed.
The next eight are muxed, half with Ethernet (which uses most of
those pins anyway).
Tested on DM355 (10 unbanked IRQs _or_ 104 banked ones) and also
on DM365 (16 unbanked ones, only 8 made available).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The current gpio code needs to know the number of
gpio irqs there are and what the bank irq number is.
To determine those values, it checks the SoC type.
It also assumes that the base address and the number
of irqs the interrupt controller uses is fixed.
To clean up the SoC checks and make it support
different base addresses and interrupt controllers,
have the SoC-specific code set those values in
the soc_info structure and have the gpio code
reference them there.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Update the DaVinci GPIO code to work better on non-dm6446 parts,
notably the dm355:
- Only handle the number of GPIOs the chip actually has. So
for example on dm6467, GPIO-42 is the last GPIO, and trying
to use GPIO-43 now fails cleanly; or GPIO-72 on dm6446.
- Enable GPIO interrupts on each 16-bit GPIO-irq bank ...
previously, only the first five were enabled, so GPIO-80
and above (on dm355) wouldn't trigger IRQs.
- Use the right IRQ for each GPIO bank. The wrong values were
used for dm355 chips, so GPIO IRQs got routed incorrectly.
- Handle up to four pairs of 16-bit GPIO banks ... previously
only three were handled, so accessing GPIO-96 and up (e.g. on
dm355) would oops.
- Update several comments that were dm6446-specific.
Verified by receiving GPIO-1 (dm9000) and GPIO-5 (msp430) IRQs
on the DM355 EVM.
One thing this doesn't do is handle the way some of the GPIO
numbers on dm6467 are reserved but aren't valid as GPIOs. Some
bitmap logic could fix that if needed.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add arch-specific ioremap() which uses any existing static mappings in
place of doing a new mapping. From now on, drivers should always use
ioremap() instead of IO_ADDRESS().
In addition, remove the davinci_[read|write]* macros in favor of using
ioremap.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
arch/arm/mach-at91/at91cap9.c:337: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91rm9200.c:301: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9260.c:351: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9261.c:287: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9263.c:312: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9rl.c:304: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-h720x/h7202-eval.c:38: error: implicit declaration of function 'IRQ_CHAINED_GPIOB'
arch/arm/mach-ks8695/devices.c:46: error: 'KS8695_IRQ_WAN_RX_STATUS' undeclared here (not in a function)
arch/arm/mach-msm/devices.c:28: error: 'INT_UART1' undeclared here (not in a function)
arch/arm/mach-mx2/devices.c:233: error: 'MXC_GPIO_IRQ_START' undeclared here (not in a function)
arch/arm/mach-mx3/devices.c:128: error: 'MXC_GPIO_IRQ_START' undeclared here (not in a function)
arch/arm/mach-omap1/mcbsp.c:140: error: 'INT_730_McBSP1RX' undeclared here (not in a function)
arch/arm/mach-omap1/mcbsp.c:165: error: 'INT_McBSP1RX' undeclared here (not in a function)
arch/arm/mach-omap1/mcbsp.c:200: error: 'INT_McBSP1RX' undeclared here (not in a function)
arch/arm/mach-omap2/board-apollon.c:286: error: implicit declaration of function 'omap_set_gpio_direction'
arch/arm/mach-omap2/mcbsp.c:154: error: 'INT_24XX_MCBSP1_IRQ_RX' undeclared here (not in a function)
arch/arm/mach-omap2/mcbsp.c:181: error: 'INT_24XX_MCBSP1_IRQ_RX' undeclared here (not in a function)
arch/arm/mach-pxa/e350.c:36: error: 'IRQ_BOARD_START' undeclared here (not in a function)
arch/arm/plat-s3c/dev-i2c0.c:32: error: 'IRQ_IIC' undeclared here (not in a function)
...
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Switch DaVinci SOC gpios over to using the new GPIO library, so it can
access GPIO expanders and other non-SOC GPIOs using the same calls.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
