Braswell eMMC host controller specifies an incorrect
timeout clock frequncy in the capabilities registers.
The correct value is 1 MHz.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for card detect for Bay Trail
and Braswell SD Card host controllers in PCI
mode.
This uses the gpio descriptor API which can find
gpio descriptors, for example, on an ACPI comapnion
device.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Due to HW issue, SDHCI host controller on Intel
Baytrail/Merrifield platforms can not use preset
register. So, disable preset registers for them by quirks.
Signed-off-by: Yunpeng Gao <yunpeng.gao@intel.com>
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The hardware is the same as used in Baytrail. Add these new PCI IDs to the
driver's list of supported IDs.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This allows us to get rid of the #else condition, as the macro compiles
away to nothing if not enabled.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It is not required (in fact it even is not recommended) that a PCI
driver's suspend() callback save the standard configuration registers
of the device, prepare it for waking up the system, or put it into a
low-power state. All of these operations can very well be taken
care of by the PCI subsystem, without the driver's participation. Thus
remove these PCI functions.
For the device which has wake up capability, use device_init_wakeup to
init the wake up capability so that PCI core will help to enable the wakeup
for it.
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This is to enable DDR50 bus speed mode with 1.8V signaling capability
for BayTrail ACPI and PCI mode eMMC Controller.
Signed-off-by: Maurice Petallo <mauricex.r.petallo@intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
"SDHCI_QUIRK2_PRESET_VALUE_BROKEN" quirk is added to prohibit
preset value enabling for Baytrail eMMC controller.
Signed-off-by: Maurice Petallo <mauricex.r.petallo@intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add sdhci_set_uhs_signaling() and always call the set_uhs_signaling
method. This avoids quirks being added into sdhci_set_uhs_signaling().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
[Ulf Hansson] Resolved conflict
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Rather than having platform_reset_enter/platform_reset_exit methods,
turn the core of the reset handling into a library function which
platforms can call at the appropriate moment in their (new) reset
method.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Add support for realtek rts5250 pci card reader. The card reader has
some problems with DDR50 mode, so add a new quirks2 for broken ddr50.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Chris Ball <chris@printf.net>
It is possible for chip->fixes to be null. Check before dereferencing it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable <stable@vger.kernel.org> # 3.11+
Signed-off-by: Chris Ball <chris@printf.net>
A host controller for a SD card may need a GPIO for card detect in order
to wake up from runtime suspend when a card is inserted. If that GPIO is
not configured, then the host controller will not wake up. Fix that for
the affected devices by not enabling runtime PM unless the GPIO is
successfully set up.
This affects BYT sd card host controller which had runtime PM enabled from
v3.11. For completeness, the MFD sd card host controller is flagged also.
The original patch before rebasing (see link below) was tested on v3.11.10
and v3.12.4 although the patch applied with some offsets and fuzz. The
original patch is here:
http://marc.info/?l=linux-mmc&m=138676702327057
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable <stable@vger.kernel.org> # 3.11+
Signed-off-by: Chris Ball <chris@printf.net>
Add O2Micro/BayHubTech SD Host DeviceId 8520 support.
Add O2Micro/BayHubTech SD Host DeviceId 8420 & 8421 support.
Add O2Micro/BayHubTech SD Host DeviceId 8620 & 8621 support.
These card readers are used in laptops like Lenovo ThinkPad W540,
Dell Latitude E5440, Dell Latitude E6540.
Signed-off-by: Peter Guo <peter.guo@bayhubtech.com>
Signed-off-by: Adam Lee <adam.lee@canonical.com>
Signed-off-by: Chris Ball <chris@printf.net>
Break out definitions in sdhci-pci.c to sdhci-pci.h, for introducing
module files like sdhci-pci-xxx.c
Signed-off-by: Adam Lee <adam.lee@canonical.com>
Signed-off-by: Chris Ball <chris@printf.net>
This patch adds intel_mid clovertrail SDIO and eMMC device
IDs to the sdhci-pci driver.
Signed-off-by: Eric Ernst <eric.ernst@linux.intel.com>
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Implement initial SDHCI Intel Merrifield support. This patch is based
on previous one from Yunpeng Gao <yunpeng.gao@intel.com>.
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add another PCI device id for an eMMC host controller.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add MMC_CAP2_NO_PRESCAN_POWERUP to sdhci-pci.c also, use mmc_power_off()
for MMC_CAP2_NO_PRESCAN_POWERUP.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
[cjb: previously applied v1 of this patch instead of v4]
Signed-off-by: Chris Ball <cjb@laptop.org>
ACPI spec 5 defined the _ADR encoding for sdio bus as:
High word - slot number (0 based)
Low word - function number
This patch adds support for binding sdio function device with acpi node,
and if successful, involve acpi into its power management.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The 8bit in the function name is misleading. When set, it will be
used to set the bus width, regardless of whether 8bit or another
bus width is requested, so change the function name to
platform_bus_width.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Here's the large driver core updates for 3.8-rc1.
The biggest thing here is the various __dev* marking removals. This is
going to be a pain for the merge with different subsystem trees, I know,
but all of the patches included here have been ACKed by their various
subsystem maintainers, as they wanted them to go through here.
If this is too much of a pain, I can pull all of them out of this tree
and just send you one with the other fixes/updates and then, after
3.8-rc1 is out, do the rest of the removals to ensure we catch them all,
it's up to you. The merges should all be trivial, and Stephen has been
doing them all in linux-next for a few weeks now quite easily.
Other than the __dev* marking removals, there's nothing major here, some
firmware loading updates and other minor things in the driver core.
All of these have (much to Stephen's annoyance), been in linux-next for
a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlDHkPkACgkQMUfUDdst+ykaWgCfW7AM30cv0nzoVO08ax6KjlG1
KVYAn3z/KYazvp4B6LMvrW9y0G34Wmad
=yvVr
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg Kroah-Hartman:
"Here's the large driver core updates for 3.8-rc1.
The biggest thing here is the various __dev* marking removals. This
is going to be a pain for the merge with different subsystem trees, I
know, but all of the patches included here have been ACKed by their
various subsystem maintainers, as they wanted them to go through here.
If this is too much of a pain, I can pull all of them out of this tree
and just send you one with the other fixes/updates and then, after
3.8-rc1 is out, do the rest of the removals to ensure we catch them
all, it's up to you. The merges should all be trivial, and Stephen
has been doing them all in linux-next for a few weeks now quite
easily.
Other than the __dev* marking removals, there's nothing major here,
some firmware loading updates and other minor things in the driver
core.
All of these have (much to Stephen's annoyance), been in linux-next
for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fixed up trivial conflicts in drivers/gpio/gpio-{em,stmpe}.c due to gpio
update.
* tag 'driver-core-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (93 commits)
modpost.c: Stop checking __dev* section mismatches
init.h: Remove __dev* sections from the kernel
acpi: remove use of __devinit
PCI: Remove __dev* markings
PCI: Always build setup-bus when PCI is enabled
PCI: Move pci_uevent into pci-driver.c
PCI: Remove CONFIG_HOTPLUG ifdefs
unicore32/PCI: Remove CONFIG_HOTPLUG ifdefs
sh/PCI: Remove CONFIG_HOTPLUG ifdefs
powerpc/PCI: Remove CONFIG_HOTPLUG ifdefs
mips/PCI: Remove CONFIG_HOTPLUG ifdefs
microblaze/PCI: Remove CONFIG_HOTPLUG ifdefs
dma: remove use of __devinit
dma: remove use of __devexit_p
firewire: remove use of __devinitdata
firewire: remove use of __devinit
leds: remove use of __devexit
leds: remove use of __devinit
leds: remove use of __devexit_p
mmc: remove use of __devexit
...
The Ricoh SDHCI controllers support Highspeed clocks as evident from
the ricoh_mmc_probe_slot() settings. Hence, SDHCI_CAN_DO_HISPD needs
to be set to enable SDIO client drivers to set/enable high speed clock
settings
Signed-off-by: Madhvapathi Sriram <Madhvapathi.Sriram@csr.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Chris Ball <cjb@laptop.org>
Cc: "Michał Mirosław" <mirq-linux@rere.qmqm.pl>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Venkatraman S <svenkatr@ti.com>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: Bruce Chang <brucechang@via.com.tw>
Cc: Harald Welte <HaraldWelte@viatech.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devinitconst is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Chris Ball <cjb@laptop.org>
Cc: linux-mmc@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Chris Ball <cjb@laptop.org>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Cc: "Michał Mirosław" <mirq-linux@rere.qmqm.pl>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Venkatraman S <svenkatr@ti.com>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: Bruce Chang <brucechang@via.com.tw>
Cc: Harald Welte <HaraldWelte@viatech.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Chris Ball <cjb@laptop.org>
Cc: "Michał Mirosław" <mirq-linux@rere.qmqm.pl>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Venkatraman S <svenkatr@ti.com>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: Bruce Chang <brucechang@via.com.tw>
Cc: Harald Welte <HaraldWelte@viatech.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SDHCI standard defines a 256 byte register set but a device
that specifies a larger iomem region is not an error. Alter the
message condition accordingly.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Core:
- Add DT properties for card detection (broken-cd, cd-gpios, non-removable)
- Don't poll non-removable devices
- Fixup/rework eMMC sleep mode/"power off notify" feature
- Support eMMC background operations (BKOPS). To set the one-time
programmable fuse that enables bkops on an eMMC that doesn't already
have it set, you can use the "mmc bkops enable" command in:
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc-utils.git
Drivers:
- atmel-mci, dw_mmc, pxa-mci, dove, s3c, spear: Add device tree support
- bfin_sdh: Add support for the controller in bf60x
- dw_mmc: Support Samsung Exynos SoCs
- eSDHC: Add ADMA support
- sdhci: Support testing a cd-gpio (from slot-gpio) instead of presence bit
- sdhci-pltfm: Support broken-cd DT property
- tegra: Convert to only supporting DT (mach-tegra has gone DT-only)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=qyY5
-----END PGP SIGNATURE-----
Merge tag 'mmc-merge-for-3.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"Core:
- Add DT properties for card detection (broken-cd, cd-gpios,
non-removable)
- Don't poll non-removable devices
- Fixup/rework eMMC sleep mode/"power off notify" feature
- Support eMMC background operations (BKOPS). To set the one-time
programmable fuse that enables bkops on an eMMC that doesn't
already have it set, you can use the "mmc bkops enable" command in:
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc-utils.git
Drivers:
- atmel-mci, dw_mmc, pxa-mci, dove, s3c, spear: Add device tree
support
- bfin_sdh: Add support for the controller in bf60x
- dw_mmc: Support Samsung Exynos SoCs
- eSDHC: Add ADMA support
- sdhci: Support testing a cd-gpio (from slot-gpio) instead of
presence bit
- sdhci-pltfm: Support broken-cd DT property
- tegra: Convert to only supporting DT (mach-tegra has gone DT-only)"
* tag 'mmc-merge-for-3.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (67 commits)
mmc: core: Fixup broken suspend and eMMC4.5 power off notify
mmc: sdhci-spear: Add clk_{un}prepare() support
mmc: sdhci-spear: add device tree bindings
mmc: sdhci-s3c: Add clk_(enable/disable) in runtime suspend/resume
mmc: core: Replace MMC_CAP2_BROKEN_VOLTAGE with test for fixed regulator
mmc: sdhci-pxav3: Use sdhci_get_of_property for parsing DT quirks
mmc: dt: Support "broken-cd" property in sdhci-pltfm
mmc: sdhci-s3c: fix the wrong number of max bus clocks
mmc: sh-mmcif: avoid oops on spurious interrupts
mmc: sh-mmcif: properly handle MMC_WRITE_MULTIPLE_BLOCK completion IRQ
mmc: sdhci-s3c: Fix crash on module insertion for second time
mmc: sdhci-s3c: Enable only required bus clock
mmc: Revert "mmc: dw_mmc: Add check for IDMAC configuration"
mmc: mxcmmc: fix bug that may block a data transfer forever
mmc: omap_hsmmc: Pass on the suspend failure to the PM core
mmc: atmel-mci: AP700x PDC is not connected to MCI
mmc: atmel-mci: DMA can be used with other controllers
mmc: mmci: use clk_prepare_enable and clk_disable_unprepare
mmc: sdhci-s3c: Add device tree support
mmc: dw_mmc: add support for exynos specific implementation of dw-mshc
...
module_pci_driver makes the code simpler by eliminating
module_init and module_exit calls.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
At http://dev.laptop.org/ticket/11980 we have determined that the
Marvell CaFe SDHCI controller reports bad card presence during
resume. It reports that no card is present even when it is.
This is a regression -- resume worked back around 2.6.37.
Around 400ms after resuming, a "card inserted" interrupt is
generated, at which point it starts reporting presence.
Work around this hardware oddity by setting the
SDHCI_QUIRK_BROKEN_CARD_DETECTION flag.
Thanks to Chris Ball for helping with diagnosis.
Signed-off-by: Daniel Drake <dsd@laptop.org>
[stable@: please apply to 3.0+]
Cc: <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This reverts commit e6039832be.
There are reports of MSI breaking SDHCI on multiple chipsets (JMicron
and O2Micro, at least), so this should be reverted until we come up
with a whitelist or something.
Signed-off-by: Chris Ball <cjb@laptop.org>
This reverts commit c16e981b2fd9455af670a69a84f4c8cf07e12658, because
it's no longer useful once MSI support is reverted.
Signed-off-by: Chris Ball <cjb@laptop.org>
MSI on my O2Micro OZ600 SD card reader is broken. This patch adds a quirk
to disable MSI on these controllers.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
SDIO is powered separately from the host controller, so the card can
remain on while the host controller is powered off during suspend.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Set Medfield SDIO as non-removable to avoid un-necessary
card detect activity.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
