This reverts commit 36ae3c0a36.
The commit broke compilation on !CONFIG_HAVE_KVM_IRQ_ROUTING. Also,
there may be cases with CONFIG_HAVE_KVM_IRQ_ROUTING, where larger
gsi values make sense.
As the commit was meant as an early indicator to user space that
something is wrong, reverting just restores the previous behavior
where overly large values are ignored when encountered (without
any direct feedback).
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: Jan H. Schönherr <jschoenh@amazon.de>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
This is a generic call and can be suceptible to races
in reading the wq task_list while another task is adding
itself to the list. Add a full barrier by using the
swq_has_sleeper() helper.
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
... as we've got the new helper now. This caller already
does the right thing, hence no changes in semantics.
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We cannot add routes for gsi values >= KVM_MAX_IRQ_ROUTES -- see
kvm_set_irq_routing(). Hence, there is no sense in accepting them
via KVM_IRQFD. Prevent them from entering the system in the first
place.
Signed-off-by: Jan H. Schönherr <jschoenh@amazon.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
commit 3898da947b ("KVM: avoid using rcu_dereference_protected") can
trigger the following lockdep/rcu splat if the VM_CREATE ioctl fails,
for example if kvm_arch_init_vm fails:
WARNING: suspicious RCU usage
4.13.0+ #105 Not tainted
-----------------------------
./include/linux/kvm_host.h:481 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
no locks held by qemu-system-s39/79.
stack backtrace:
CPU: 0 PID: 79 Comm: qemu-system-s39 Not tainted 4.13.0+ #105
Hardware name: IBM 2964 NC9 704 (KVM/Linux)
Call Trace:
([<00000000001140b2>] show_stack+0xea/0xf0)
[<00000000008a68a4>] dump_stack+0x94/0xd8
[<0000000000134c12>] kvm_dev_ioctl+0x372/0x7a0
[<000000000038f940>] do_vfs_ioctl+0xa8/0x6c8
[<0000000000390004>] SyS_ioctl+0xa4/0xb8
[<00000000008c7a8c>] system_call+0xc4/0x27c
no locks held by qemu-system-s39/79.
We have to reset the just created users_count back to 0 to
tell the check to not trigger.
Reported-by: Stefan Haberland <sth@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Fixes: 3898da947b ("KVM: avoid using rcu_dereference_protected")
Cc: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Common:
- improve heuristic for boosting preempted spinlocks by ignoring VCPUs
in user mode
ARM:
- fix for decoding external abort types from guests
- added support for migrating the active priority of interrupts when
running a GICv2 guest on a GICv3 host
- minor cleanup
PPC:
- expose storage keys to userspace
- merge powerpc/topic/ppc-kvm branch that contains
find_linux_pte_or_hugepte and POWER9 thread management cleanup
- merge kvm-ppc-fixes with a fix that missed 4.13 because of vacations
- fixes
s390:
- merge of topic branch tlb-flushing from the s390 tree to get the
no-dat base features
- merge of kvm/master to avoid conflicts with additional sthyi fixes
- wire up the no-dat enhancements in KVM
- multiple epoch facility (z14 feature)
- Configuration z/Architecture Mode
- more sthyi fixes
- gdb server range checking fix
- small code cleanups
x86:
- emulate Hyper-V TSC frequency MSRs
- add nested INVPCID
- emulate EPTP switching VMFUNC
- support Virtual GIF
- support 5 level page tables
- speedup nested VM exits by packing byte operations
- speedup MMIO by using hardware provided physical address
- a lot of fixes and cleanups, especially nested
-----BEGIN PGP SIGNATURE-----
iQEcBAABCAAGBQJZspE1AAoJEED/6hsPKofoDcMIALT11n+LKV50QGwQdg2W1GOt
aChbgnj/Kegit3hQlDhVNb8kmdZEOZzSL81Lh0VPEr7zXU8QiWn2snbizDPv8sde
MpHhcZYZZ0YrpoiZKjl8yiwcu88OWGn2qtJ7OpuTS5hvEGAfxMncp0AMZho6fnz/
ySTwJ9GK2MTgBw39OAzCeDOeoYn4NKYMwjJGqBXRhNX8PG/1wmfqv0vPrd6wfg31
KJ58BumavwJjr8YbQ1xELm9rpQrAmaayIsG0R1dEUqCbt5a1+t2gt4h2uY7tWcIv
ACt2bIze7eF3xA+OpRs+eT+yemiH3t9btIVmhCfzUpnQ+V5Z55VMSwASLtTuJRQ=
=R8Ry
-----END PGP SIGNATURE-----
Merge tag 'kvm-4.14-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Radim Krčmář:
"First batch of KVM changes for 4.14
Common:
- improve heuristic for boosting preempted spinlocks by ignoring
VCPUs in user mode
ARM:
- fix for decoding external abort types from guests
- added support for migrating the active priority of interrupts when
running a GICv2 guest on a GICv3 host
- minor cleanup
PPC:
- expose storage keys to userspace
- merge kvm-ppc-fixes with a fix that missed 4.13 because of
vacations
- fixes
s390:
- merge of kvm/master to avoid conflicts with additional sthyi fixes
- wire up the no-dat enhancements in KVM
- multiple epoch facility (z14 feature)
- Configuration z/Architecture Mode
- more sthyi fixes
- gdb server range checking fix
- small code cleanups
x86:
- emulate Hyper-V TSC frequency MSRs
- add nested INVPCID
- emulate EPTP switching VMFUNC
- support Virtual GIF
- support 5 level page tables
- speedup nested VM exits by packing byte operations
- speedup MMIO by using hardware provided physical address
- a lot of fixes and cleanups, especially nested"
* tag 'kvm-4.14-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (67 commits)
KVM: arm/arm64: Support uaccess of GICC_APRn
KVM: arm/arm64: Extract GICv3 max APRn index calculation
KVM: arm/arm64: vITS: Drop its_ite->lpi field
KVM: arm/arm64: vgic: constify seq_operations and file_operations
KVM: arm/arm64: Fix guest external abort matching
KVM: PPC: Book3S HV: Fix memory leak in kvm_vm_ioctl_get_htab_fd
KVM: s390: vsie: cleanup mcck reinjection
KVM: s390: use WARN_ON_ONCE only for checking
KVM: s390: guestdbg: fix range check
KVM: PPC: Book3S HV: Report storage key support to userspace
KVM: PPC: Book3S HV: Fix case where HDEC is treated as 32-bit on POWER9
KVM: PPC: Book3S HV: Fix invalid use of register expression
KVM: PPC: Book3S HV: Fix H_REGISTER_VPA VPA size validation
KVM: PPC: Book3S HV: Fix setting of storage key in H_ENTER
KVM: PPC: e500mc: Fix a NULL dereference
KVM: PPC: e500: Fix some NULL dereferences on error
KVM: PPC: Book3S HV: Protect updates to spapr_tce_tables list
KVM: s390: we are always in czam mode
KVM: s390: expose no-DAT to guest and migration support
KVM: s390: sthyi: remove invalid guest write access
...
When migrating guests around we need to know the active priorities to
ensure functional virtual interrupt prioritization by the GIC.
This commit clarifies the API and how active priorities of interrupts in
different groups are represented, and implements the accessor functions
for the uaccess register range.
We live with a slight layering violation in accessing GICv3 data
structures from vgic-mmio-v2.c, because anything else just adds too much
complexity for us to deal with (it's not like there's a benefit
elsewhere in the code of an intermediate representation as is the case
with the VMCR). We accept this, because while doing v3 processing from
a file named something-v2.c can look strange at first, this really is
specific to dealing with the user space interface for something that
looks like a GICv2.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
As we are about to access the APRs from the GICv2 uaccess interface,
make this logic generally available.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
For unknown reasons, the its_ite data structure carries an "lpi" field
which contains the intid of the LPI. This is an obvious duplication
of the vgic_irq->intid field, so let's fix the only user and remove
the now useless field.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
vgic_debug_seq_ops and file_operations are not supposed to change
at runtime and none of the structures is modified.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
The ARM-ARM has two bits in the ESR/HSR relevant to external aborts.
A range of {I,D}FSC values (of which bit 5 is always set) and bit 9 'EA'
which provides:
> an IMPLEMENTATION DEFINED classification of External Aborts.
This bit is in addition to the {I,D}FSC range, and has an implementation
defined meaning. KVM should always ignore this bit when handling external
aborts from a guest.
Remove the ESR_ELx_EA definition and rewrite its helper
kvm_vcpu_dabt_isextabt() to check the {I,D}FSC range. This merges
kvm_vcpu_dabt_isextabt() and the recently added is_abort_sea() helper.
CC: Tyler Baicar <tbaicar@codeaurora.org>
Reported-by: gengdongjiu <gengdj.1984@gmail.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Calls to mmu_notifier_invalidate_page() were replaced by calls to
mmu_notifier_invalidate_range() and are now bracketed by calls to
mmu_notifier_invalidate_range_start()/end()
Remove now useless invalidate_page callback.
Changed since v1 (Linus Torvalds)
- remove now useless kvm_arch_mmu_notifier_invalidate_page()
Signed-off-by: Jérôme Glisse <jglisse@redhat.com>
Tested-by: Mike Galbraith <efault@gmx.de>
Tested-by: Adam Borowski <kilobyte@angband.pl>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: kvm@vger.kernel.org
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When PAGE_OFFSET is not a compile-time constant, we run into
warnings from the use of kvm_is_error_hva() that the compiler
cannot optimize out:
arch/arm/kvm/../../../virt/kvm/kvm_main.c: In function '__kvm_gfn_to_hva_cache_init':
arch/arm/kvm/../../../virt/kvm/kvm_main.c:1978:14: error: 'nr_pages_avail' may be used uninitialized in this function [-Werror=maybe-uninitialized]
arch/arm/kvm/../../../virt/kvm/kvm_main.c: In function 'gfn_to_page_many_atomic':
arch/arm/kvm/../../../virt/kvm/kvm_main.c:1660:5: error: 'entry' may be used uninitialized in this function [-Werror=maybe-uninitialized]
This adds fake initializations to the two instances I ran into.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
This implements the kvm_arch_vcpu_in_kernel() for ARM, and adjusts
the calls to kvm_vcpu_on_spin().
Signed-off-by: Longpeng(Mike) <longpeng2@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If a vcpu exits due to request a user mode spinlock, then
the spinlock-holder may be preempted in user mode or kernel mode.
(Note that not all architectures trap spin loops in user mode,
only AMD x86 and ARM/ARM64 currently do).
But if a vcpu exits in kernel mode, then the holder must be
preempted in kernel mode, so we should choose a vcpu in kernel mode
as a more likely candidate for the lock holder.
This introduces kvm_arch_vcpu_in_kernel() to decide whether the
vcpu is in kernel-mode when it's preempted. kvm_vcpu_on_spin's
new argument says the same of the spinning VCPU.
Signed-off-by: Longpeng(Mike) <longpeng2@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- Yet another race with VM destruction plugged
- A set of small vgic fixes
-----BEGIN PGP SIGNATURE-----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=TMR9
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-for-v4.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm
KVM/ARM Fixes for v4.13-rc4
- Yet another race with VM destruction plugged
- A set of small vgic fixes
There is a small chance that the compiler could generate separate loads
for the dist->propbaser which could be modified from another CPU. As we
want to make sure we atomically update the entire value, and don't race
with other updates, guarantee that the cmpxchg operation compares
against the original value.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
During teardown, accesses to memslots and buses are using
rcu_dereference_protected with an always-true condition because
these accesses are done outside the usual mutexes. This
is because the last reference is gone and there cannot be any
concurrent modifications, but rcu_dereference_protected is
ugly and unobvious.
Instead, check the refcount in kvm_get_bus and __kvm_memslots.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Simplify and improve the code so that the PID is always available in
the uevent even when debugfs is not available.
This adds a userspace_pid field to struct kvm, as per Radim's
suggestion, so that the PID can be retrieved on destruction too.
Acked-by: Janosch Frank <frankja@linux.vnet.ibm.com>
Fixes: 286de8f6ac ("KVM: trigger uevents when creating or destroying a VM")
Signed-off-by: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The mmu_notifier_release() callback of KVM triggers cleaning up
the stage2 page table on kvm-arm. However there could be other
notifier callbacks in parallel with the mmu_notifier_release(),
which could cause the call backs ending up in an empty stage2
page table. Make sure we check it for all the notifier callbacks.
Cc: stable@vger.kernel.org
Fixes: commit 293f29363 ("kvm-arm: Unmap shadow pagetables properly")
Reported-by: Alex Graf <agraf@suse.de>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
kvm_pmu_overflow_set() is called from perf's interrupt handler,
making the call of kvm_vgic_inject_irq() from it introduced with
"KVM: arm/arm64: PMU: remove request-less vcpu kick" a really bad
idea, as it's quite easy to try and retake a lock that the
interrupted context is already holding. The fix is to use a vcpu
kick, leaving the interrupt injection to kvm_pmu_sync_hwstate(),
like it was doing before the refactoring. We don't just revert,
though, because before the kick was request-less, leaving the vcpu
exposed to the request-less vcpu kick race, and also because the
kick was used unnecessarily from register access handlers.
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Commit 0e4e82f154 ("KVM: arm64: vgic-its: Enable ITS emulation as
a virtual MSI controller") tried to advertise KVM_CAP_MSI_DEVID, but
the code logic was not updating the dist->msis_require_devid field
correctly. If hypervisor tool creates the ITS device after VGIC
initialization then we don't advertise KVM_CAP_MSI_DEVID capability.
Update the field msis_require_devid to true inside vgic_its_create()
to fix the issue.
Fixes: 0e4e82f154 ("vgic-its: Enable ITS emulation as a virtual MSI controller")
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Common:
- add uevents for VM creation/destruction
- annotate and properly access RCU-protected objects
s390:
- rename IOCTL added in the first v4.13 merge
x86:
- emulate VMLOAD VMSAVE feature in SVM
- support paravirtual asynchronous page fault while nested
- add Hyper-V userspace interfaces for better migration
- improve master clock corner cases
- extend internal error reporting after EPT misconfig
- correct single-stepping of emulated instructions in SVM
- handle MCE during VM entry
- fix nVMX VM entry checks and nVMX VMCS shadowing
-----BEGIN PGP SIGNATURE-----
iQEcBAABCAAGBQJZaOm6AAoJEED/6hsPKofoqO8H/3breVIyVv9mwg7A5+o+6LTq
GzV/YXHSC8NtfxZn8ViS/TCziYiBSFv7XiPSodkXbOgYSz8Yya5x9D+dbEH+xgG7
l+LsZEqdSFbHCkvKrMiwSsoXtsT5WygA56+KZiBmu8cvlwqSyXWHFn3ZJ1wKzGq/
zivlkfCoh2m6bGdNmrG9pHUSgxvDh94pXesaVBKy4hgeovY1qjzby3Lo+HuIUzai
exuEU1EKRlUIfLK1B2Anp5IIv5Q1lFnMSvD6YSiWYywZb95dN/adsX1bv+MKeOdt
TIAgotsWjaAuT9JolAJjfVPHG0+uMBMsWg4Zh9Ra/gPPaSh3KEC2h1++zEYKjvw=
=1zII
-----END PGP SIGNATURE-----
Merge tag 'kvm-4.13-2' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull more KVM updates from Radim Krčmář:
"Second batch of KVM updates for v4.13
Common:
- add uevents for VM creation/destruction
- annotate and properly access RCU-protected objects
s390:
- rename IOCTL added in the first v4.13 merge
x86:
- emulate VMLOAD VMSAVE feature in SVM
- support paravirtual asynchronous page fault while nested
- add Hyper-V userspace interfaces for better migration
- improve master clock corner cases
- extend internal error reporting after EPT misconfig
- correct single-stepping of emulated instructions in SVM
- handle MCE during VM entry
- fix nVMX VM entry checks and nVMX VMCS shadowing"
* tag 'kvm-4.13-2' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (28 commits)
kvm: x86: hyperv: make VP_INDEX managed by userspace
KVM: async_pf: Let guest support delivery of async_pf from guest mode
KVM: async_pf: Force a nested vmexit if the injected #PF is async_pf
KVM: async_pf: Add L1 guest async_pf #PF vmexit handler
KVM: x86: Simplify kvm_x86_ops->queue_exception parameter list
kvm: x86: hyperv: add KVM_CAP_HYPERV_SYNIC2
KVM: x86: make backwards_tsc_observed a per-VM variable
KVM: trigger uevents when creating or destroying a VM
KVM: SVM: Enable Virtual VMLOAD VMSAVE feature
KVM: SVM: Add Virtual VMLOAD VMSAVE feature definition
KVM: SVM: Rename lbr_ctl field in the vmcb control area
KVM: SVM: Prepare for new bit definition in lbr_ctl
KVM: SVM: handle singlestep exception when skipping emulated instructions
KVM: x86: take slots_lock in kvm_free_pit
KVM: s390: Fix KVM_S390_GET_CMMA_BITS ioctl definition
kvm: vmx: Properly handle machine check during VM-entry
KVM: x86: update master clock before computing kvmclock_offset
kvm: nVMX: Shadow "high" parts of shadowed 64-bit VMCS fields
kvm: nVMX: Fix nested_vmx_check_msr_bitmap_controls
kvm: nVMX: Validate the I/O bitmaps on nested VM-entry
...
- Include Intel XXV710 in INTx workaround (Alex Williamson)
- Make use of ERR_CAST() for error return (Dan Carpenter)
- Fix vfio_group release deadlock from iommu notifier (Alex Williamson)
- Unset KVM-VFIO attributes only on group match (Alex Williamson)
- Fix release path group/file matching with KVM-VFIO (Alex Williamson)
- Remove unnecessary lock uses triggering lockdep splat (Alex Williamson)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)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=3A4K
-----END PGP SIGNATURE-----
Merge tag 'vfio-v4.13-rc1' of git://github.com/awilliam/linux-vfio
Pull VFIO updates from Alex Williamson:
- Include Intel XXV710 in INTx workaround (Alex Williamson)
- Make use of ERR_CAST() for error return (Dan Carpenter)
- Fix vfio_group release deadlock from iommu notifier (Alex Williamson)
- Unset KVM-VFIO attributes only on group match (Alex Williamson)
- Fix release path group/file matching with KVM-VFIO (Alex Williamson)
- Remove unnecessary lock uses triggering lockdep splat (Alex Williamson)
* tag 'vfio-v4.13-rc1' of git://github.com/awilliam/linux-vfio:
vfio: Remove unnecessary uses of vfio_container.group_lock
vfio: New external user group/file match
kvm-vfio: Decouple only when we match a group
vfio: Fix group release deadlock
vfio: Use ERR_CAST() instead of open coding it
vfio/pci: Add Intel XXV710 to hidden INTx devices
This patch adds a few lines to the KVM common code to fire a
KOBJ_CHANGE uevent whenever a KVM VM is created or destroyed. The event
carries five environment variables:
CREATED indicates how many times a new VM has been created. It is
useful for example to trigger specific actions when the first
VM is started
COUNT indicates how many VMs are currently active. This can be used for
logging or monitoring purposes
PID has the pid of the KVM process that has been started or stopped.
This can be used to perform process-specific tuning.
STATS_PATH contains the path in debugfs to the directory with all the
runtime statistics for this VM. This is useful for performance
monitoring and profiling.
EVENT described the type of event, its value can be either "create" or
"destroy"
Specific udev rules can be then set up in userspace to deal with the
creation or destruction of VMs as needed.
Signed-off-by: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
The uniprocessor version of smp_call_function_many does not evaluate
all of its argument, and the compiler emits a warning about "wait"
being unused. This breaks the build on architectures for which
"-Werror" is enabled by default.
Work around it by moving the invocation of smp_call_function_many to
its own inline function.
Reported-by: Paul Mackerras <paulus@ozlabs.org>
Cc: stable@vger.kernel.org
Fixes: 7a97cec26b
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
we access the memslots array via srcu. Mark it as such and
use the right access functions also for the freeing of
memory slots.
Found by sparse:
./include/linux/kvm_host.h:565:16: error: incompatible types in
comparison expression (different address spaces)
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
mark kvm->busses as rcu protected and use the correct access
function everywhere.
found by sparse
virt/kvm/kvm_main.c:3490:15: error: incompatible types in comparison expression (different address spaces)
virt/kvm/kvm_main.c:3509:15: error: incompatible types in comparison expression (different address spaces)
virt/kvm/kvm_main.c:3561:15: error: incompatible types in comparison expression (different address spaces)
virt/kvm/kvm_main.c:3644:15: error: incompatible types in comparison expression (different address spaces)
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
irq routing is rcu protected. Use the proper access functions.
Found by sparse
virt/kvm/irqchip.c:233:13: warning: incorrect type in assignment (different address spaces)
virt/kvm/irqchip.c:233:13: expected struct kvm_irq_routing_table *old
virt/kvm/irqchip.c:233:13: got struct kvm_irq_routing_table [noderef] <asn:4>*irq_routing
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
We do use rcu to protect the pid pointer. Mark it as such and
adopt all code to use the proper access methods.
This was detected by sparse.
"virt/kvm/kvm_main.c:2248:15: error: incompatible types in comparison
expression (different address spaces)"
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
- Better machine check handling for HV KVM
- Ability to support guests with threads=2, 4 or 8 on POWER9
- Fix for a race that could cause delayed recognition of signals
- Fix for a bug where POWER9 guests could sleep with interrupts pending.
ARM:
- VCPU request overhaul
- allow timer and PMU to have their interrupt number selected from userspace
- workaround for Cavium erratum 30115
- handling of memory poisonning
- the usual crop of fixes and cleanups
s390:
- initial machine check forwarding
- migration support for the CMMA page hinting information
- cleanups and fixes
x86:
- nested VMX bugfixes and improvements
- more reliable NMI window detection on AMD
- APIC timer optimizations
Generic:
- VCPU request overhaul + documentation of common code patterns
- kvm_stat improvements
There is a small conflict in arch/s390 due to an arch-wide field rename.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJZW4XTAAoJEL/70l94x66DkhMH/izpk54KI17PtyQ9VYI2sYeZ
BWK6Kl886g3ij4pFi3pECqjDJzWaa3ai+vFfzzpJJ8OkCJT5Rv4LxC5ERltVVmR8
A3T1I/MRktSC0VJLv34daPC2z4Lco/6SPipUpPnL4bE2HATKed4vzoOjQ3tOeGTy
dwi7TFjKwoVDiM7kPPDRnTHqCe5G5n13sZ49dBe9WeJ7ttJauWqoxhlYosCGNPEj
g8ZX8+cvcAhVnz5uFL8roqZ8ygNEQq2mgkU18W8ZZKuiuwR0gdsG0gSBFNTdwIMK
NoreRKMrw0+oLXTIB8SZsoieU6Qi7w3xMAMabe8AJsvYtoersugbOmdxGCr1lsA=
=OD7H
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"PPC:
- Better machine check handling for HV KVM
- Ability to support guests with threads=2, 4 or 8 on POWER9
- Fix for a race that could cause delayed recognition of signals
- Fix for a bug where POWER9 guests could sleep with interrupts pending.
ARM:
- VCPU request overhaul
- allow timer and PMU to have their interrupt number selected from userspace
- workaround for Cavium erratum 30115
- handling of memory poisonning
- the usual crop of fixes and cleanups
s390:
- initial machine check forwarding
- migration support for the CMMA page hinting information
- cleanups and fixes
x86:
- nested VMX bugfixes and improvements
- more reliable NMI window detection on AMD
- APIC timer optimizations
Generic:
- VCPU request overhaul + documentation of common code patterns
- kvm_stat improvements"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (124 commits)
Update my email address
kvm: vmx: allow host to access guest MSR_IA32_BNDCFGS
x86: kvm: mmu: use ept a/d in vmcs02 iff used in vmcs12
kvm: x86: mmu: allow A/D bits to be disabled in an mmu
x86: kvm: mmu: make spte mmio mask more explicit
x86: kvm: mmu: dead code thanks to access tracking
KVM: PPC: Book3S: Fix typo in XICS-on-XIVE state saving code
KVM: PPC: Book3S HV: Close race with testing for signals on guest entry
KVM: PPC: Book3S HV: Simplify dynamic micro-threading code
KVM: x86: remove ignored type attribute
KVM: LAPIC: Fix lapic timer injection delay
KVM: lapic: reorganize restart_apic_timer
KVM: lapic: reorganize start_hv_timer
kvm: nVMX: Check memory operand to INVVPID
KVM: s390: Inject machine check into the nested guest
KVM: s390: Inject machine check into the guest
tools/kvm_stat: add new interactive command 'b'
tools/kvm_stat: add new command line switch '-i'
tools/kvm_stat: fix error on interactive command 'g'
KVM: SVM: suppress unnecessary NMI singlestep on GIF=0 and nested exit
...
- vcpu request overhaul
- allow timer and PMU to have their interrupt number
selected from userspace
- workaround for Cavium erratum 30115
- handling of memory poisonning
- the usual crop of fixes and cleanups
-----BEGIN PGP SIGNATURE-----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=6hNK
-----END PGP SIGNATURE-----
Merge tag 'kvmarm-for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/ARM updates for 4.13
- vcpu request overhaul
- allow timer and PMU to have their interrupt number
selected from userspace
- workaround for Cavium erratum 30115
- handling of memory poisonning
- the usual crop of fixes and cleanups
Conflicts:
arch/s390/include/asm/kvm_host.h
At the point where the kvm-vfio pseudo device wants to release its
vfio group reference, we can't always acquire a new reference to make
that happen. The group can be in a state where we wouldn't allow a
new reference to be added. This new helper function allows a caller
to match a file to a group to facilitate this. Given a file and
group, report if they match. Thus the caller needs to already have a
group reference to match to the file. This allows the deletion of a
group without acquiring a new reference.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Cc: stable@vger.kernel.org
Unset-KVM and decrement-assignment only when we find the group in our
list. Otherwise we can get out of sync if the user triggers this for
groups that aren't currently on our list.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: stable@vger.kernel.org
The call to kvm_put_kvm was removed from error handling in commit
506cfba9e7 ("KVM: don't use anon_inode_getfd() before possible
failures"), but it is _not_ a memory leak. Reuse Al's explanation
to avoid that someone else makes the same mistake.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Replaces "S_IRUGO | S_IWUSR" with 0644. The reason is that symbolic
permissions considered harmful:
https://lwn.net/Articles/696229/
Signed-off-by: Roman Storozhenko <romeusmeister@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently external aborts are unsupported by the guest abort
handling. Add handling for SEAs so that the host kernel reports
SEAs which occur in the guest kernel.
When an SEA occurs in the guest kernel, the guest exits and is
routed to kvm_handle_guest_abort(). Prior to this patch, a print
message of an unsupported FSC would be printed and nothing else
would happen. With this patch, the code gets routed to the APEI
handling of SEAs in the host kernel to report the SEA information.
Signed-off-by: Tyler Baicar <tbaicar@codeaurora.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Once we enable ARCH_SUPPORTS_MEMORY_FAILURE on arm64, notifications for
broken memory can call memory_failure() in mm/memory-failure.c to offline
pages of memory, possibly signalling user space processes and notifying all
the in-kernel users.
memory_failure() has two modes, early and late. Early is used by
machine-managers like Qemu to receive a notification when a memory error is
notified to the host. These can then be relayed to the guest before the
affected page is accessed. To enable this, the process must set
PR_MCE_KILL_EARLY in PR_MCE_KILL_SET using the prctl() syscall.
Once the early notification has been handled, nothing stops the
machine-manager or guest from accessing the affected page. If the
machine-manager does this the page will fail to be mapped and SIGBUS will
be sent. This patch adds the equivalent path for when the guest accesses
the page, sending SIGBUS to the machine-manager.
These two signals can be distinguished by the machine-manager using their
si_code: BUS_MCEERR_AO for 'action optional' early notifications, and
BUS_MCEERR_AR for 'action required' synchronous/late notifications.
Do as x86 does, and deliver the SIGBUS when we discover pfn ==
KVM_PFN_ERR_HWPOISON. Use the hugepage size as si_addr_lsb if this vma was
allocated as a hugepage. Transparent hugepages will be split by
memory_failure() before we see them here.
Cc: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Rename:
wait_queue_t => wait_queue_entry_t
'wait_queue_t' was always a slight misnomer: its name implies that it's a "queue",
but in reality it's a queue *entry*. The 'real' queue is the wait queue head,
which had to carry the name.
Start sorting this out by renaming it to 'wait_queue_entry_t'.
This also allows the real structure name 'struct __wait_queue' to
lose its double underscore and become 'struct wait_queue_entry',
which is the more canonical nomenclature for such data types.
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When reading the cntpct_el0 in guest with VHE (Virtual Host Extension)
enabled in host, the "Unsupported guest sys_reg access" error reported.
The reason is cnthctl_el2.EL1PCTEN is not enabled, which is expected
to be done in kvm_timer_init_vhe(). The problem is kvm_timer_init_vhe
is called by cpu_init_hyp_mode, and which is called when VHE is disabled.
This patch remove the incorrect call to kvm_timer_init_vhe() from
cpu_init_hyp_mode(), and calls kvm_timer_init_vhe() to enable
cnthctl_el2.EL1PCTEN in cpu_hyp_reinit().
Fixes: 488f94d721 ("KVM: arm64: Access CNTHCTL_EL2 bit fields correctly on VHE systems")
Cc: stable@vger.kernel.org
Signed-off-by: Hu Huajun <huhuajun@huawei.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Per ARM DDI 0487B.a, the registers are named ICC_IGRPEN*_EL1 rather than
ICC_GRPEN*_EL1. Correct our mnemonics and comments to match, before we
add more GICv3 register definitions.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: kvmarm@lists.cs.columbia.edu
Acked-by: Christoffer Dall <cdall@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
A write-to-read-only GICv3 access should UNDEF at EL1. But since
we're in complete paranoia-land with broken CPUs, let's assume the
worse and gracefully handle the case.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
A read-from-write-only GICv3 access should UNDEF at EL1. But since
we're in complete paranoia-land with broken CPUs, let's assume the
worse and gracefully handle the case.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
In order to facilitate debug, let's log which class of GICv3 system
registers are trapped.
Tested-by: Alexander Graf <agraf@suse.de>
Acked-by: David Daney <david.daney@cavium.com>
Acked-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Now that we're able to safely handle common sysreg access, let's
give the user the opportunity to enable it by passing a specific
command-line option (vgic_v3.common_trap).
Tested-by: Alexander Graf <agraf@suse.de>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Add a handler for reading/writing the guest's view of the ICC_PMR_EL1
register, which is located in the ICH_VMCR_EL2.VPMR field.
Tested-by: Alexander Graf <agraf@suse.de>
Acked-by: David Daney <david.daney@cavium.com>
Acked-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Add a handler for reading/writing the guest's view of the ICV_CTLR_EL1
register. only EOIMode and CBPR are of interest here, as all the other
bits directly come from ICH_VTR_EL2 and are Read-Only.
Tested-by: Alexander Graf <agraf@suse.de>
Acked-by: David Daney <david.daney@cavium.com>
Acked-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Add a handler for reading the guest's view of the ICV_RPR_EL1
register, returning the highest active priority.
Tested-by: Alexander Graf <agraf@suse.de>
Acked-by: David Daney <david.daney@cavium.com>
Acked-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Add a handler for writing the guest's view of the ICC_DIR_EL1
register, performing the deactivation of an interrupt if EOImode
is set ot 1.
Tested-by: Alexander Graf <agraf@suse.de>
Acked-by: David Daney <david.daney@cavium.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Some Cavium Thunder CPUs suffer a problem where a KVM guest may
inadvertently cause the host kernel to quit receiving interrupts.
Use the Group-0/1 trapping in order to deal with it.
[maz]: Adapted patch to the Group-0/1 trapping, reworked commit log
Tested-by: Alexander Graf <agraf@suse.de>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Now that we're able to safely handle Group-0 sysreg access, let's
give the user the opportunity to enable it by passing a specific
command-line option (vgic_v3.group0_trap).
Tested-by: Alexander Graf <agraf@suse.de>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
In order to be able to trap Group-0 GICv3 system registers, we need to
set ICH_HCR_EL2.TALL0 begore entering the guest. This is conditionnaly
done after having restored the guest's state, and cleared on exit.
Tested-by: Alexander Graf <agraf@suse.de>
Acked-by: David Daney <david.daney@cavium.com>
Acked-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
A number of Group-0 registers can be handled by the same accessors
as that of Group-1, so let's add the required system register encodings
and catch them in the dispatching function.
Tested-by: Alexander Graf <agraf@suse.de>
Acked-by: David Daney <david.daney@cavium.com>
Acked-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Add a handler for reading/writing the guest's view of the ICC_IGRPEN0_EL1
register, which is located in the ICH_VMCR_EL2.VENG0 field.
Tested-by: Alexander Graf <agraf@suse.de>
Acked-by: David Daney <david.daney@cavium.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Add a handler for reading/writing the guest's view of the ICC_BPR0_EL1
register, which is located in the ICH_VMCR_EL2.BPR0 field.
Tested-by: Alexander Graf <agraf@suse.de>
Acked-by: David Daney <david.daney@cavium.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Now that we're able to safely handle Group-1 sysreg access, let's
give the user the opportunity to enable it by passing a specific
command-line option (vgic_v3.group1_trap).
Tested-by: Alexander Graf <agraf@suse.de>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
In order to be able to trap Group-1 GICv3 system registers, we need to
set ICH_HCR_EL2.TALL1 before entering the guest. This is conditionally
done after having restored the guest's state, and cleared on exit.
Tested-by: Alexander Graf <agraf@suse.de>
Acked-by: David Daney <david.daney@cavium.com>
Acked-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Add a handler for reading the guest's view of the ICV_HPPIR1_EL1
register. This is a simple parsing of the available LRs, extracting the
highest available interrupt.
Tested-by: Alexander Graf <agraf@suse.de>
Acked-by: David Daney <david.daney@cavium.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Add a handler for reading/writing the guest's view of the ICV_AP1Rn_EL1
registers. We just map them to the corresponding ICH_AP1Rn_EL2 registers.
Tested-by: Alexander Graf <agraf@suse.de>
Acked-by: David Daney <david.daney@cavium.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Add a handler for writing the guest's view of the ICC_EOIR1_EL1
register. This involves dropping the priority of the interrupt,
and deactivating it if required (EOImode == 0).
Tested-by: Alexander Graf <agraf@suse.de>
Acked-by: David Daney <david.daney@cavium.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Add a handler for reading the guest's view of the ICC_IAR1_EL1
register. This involves finding the highest priority Group-1
interrupt, checking against both PMR and the active group
priority, activating the interrupt and setting the group
priority as active.
Tested-by: Alexander Graf <agraf@suse.de>
Acked-by: David Daney <david.daney@cavium.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Add a handler for reading/writing the guest's view of the ICC_IGRPEN1_EL1
register, which is located in the ICH_VMCR_EL2.VENG1 field.
Tested-by: Alexander Graf <agraf@suse.de>
Acked-by: David Daney <david.daney@cavium.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Add a handler for reading/writing the guest's view of the ICC_BPR1_EL1
register, which is located in the ICH_VMCR_EL2.BPR1 field.
Tested-by: Alexander Graf <agraf@suse.de>
Acked-by: David Daney <david.daney@cavium.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
In order to start handling guest access to GICv3 system registers,
let's add a hook that will get called when we trap a system register
access. This is gated by a new static key (vgic_v3_cpuif_trap).
Tested-by: Alexander Graf <agraf@suse.de>
Acked-by: David Daney <david.daney@cavium.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
As we're about to trap CP15 accesses and handle them at EL2, we
need to evaluate whether or not the condition flags are valid,
as an implementation is allowed to trap despite the condition
not being met.
Tagging the function as __hyp_text allows this. We still rely on
the cc_map array to be mapped at EL2 by virtue of being "const",
and the linker to only emit relative references.
Tested-by: Alexander Graf <agraf@suse.de>
Acked-by: David Daney <david.daney@cavium.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
As we're about to access the Active Priority registers a lot more,
let's define accessors that take the register number as a parameter.
Tested-by: Alexander Graf <agraf@suse.de>
Acked-by: David Daney <david.daney@cavium.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
The PMU IRQ number is set through the VCPU device's KVM_SET_DEVICE_ATTR
ioctl handler for the KVM_ARM_VCPU_PMU_V3_IRQ attribute, but there is no
enforced or stated requirement that this must happen after initializing
the VGIC. As a result, calling vgic_valid_spi() which relies on the
nr_spis being set during the VGIC init can incorrectly fail.
Introduce irq_is_spi, which determines if an IRQ number is within the
SPI range without verifying it against the actual VGIC properties.
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
When injecting an IRQ to the VGIC, you now have to present an owner
token for that IRQ line to show that you are the owner of that line.
IRQ lines driven from userspace or via an irqfd do not have an owner and
will simply pass a NULL pointer.
Also get rid of the unused kvm_vgic_inject_mapped_irq prototype.
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
We check if other in-kernel devices have already been connected to the
GIC for a particular interrupt line when possible.
For the PMU, we can do this whenever setting the PMU interrupt number
from userspace.
For the timers, we have to wait until we try to enable the timer,
because we have a concept of default IRQ numbers that userspace
shouldn't have to work around in the initialization phase.
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Having multiple devices being able to signal the same interrupt line is
very confusing and almost certainly guarantees a configuration error.
Therefore, introduce a very simple allocator which allows a device to
claim an interrupt line from the vgic for a given VM.
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
First we define an ABI using the vcpu devices that lets userspace set
the interrupt numbers for the various timers on both the 32-bit and
64-bit KVM/ARM implementations.
Second, we add the definitions for the groups and attributes introduced
by the above ABI. (We add the PMU define on the 32-bit side as well for
symmetry and it may get used some day.)
Third, we set up the arch-specific vcpu device operation handlers to
call into the timer code for anything related to the
KVM_ARM_VCPU_TIMER_CTRL group.
Fourth, we implement support for getting and setting the timer interrupt
numbers using the above defined ABI in the arch timer code.
Fifth, we introduce error checking upon enabling the arch timer (which
is called when first running a VCPU) to check that all VCPUs are
configured to use the same PPI for the timer (as mandated by the
architecture) and that the virtual and physical timers are not
configured to use the same IRQ number.
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
We currently initialize the arch timer IRQ numbers from the reset code,
presumably because we once intended to model multiple CPU or SoC types
from within the kernel and have hard-coded reset values in the reset
code.
As we are moving towards userspace being in charge of more fine-grained
CPU emulation and stitching together the pieces needed to emulate a
particular type of CPU, we should no longer have a tight coupling
between resetting a VCPU and setting IRQ numbers.
Therefore, move the logic to define and use the default IRQ numbers to
the timer code and set the IRQ number immediately when creating the
VCPU.
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
We are about to need this define in the arch timer code as well so move
it to a common location.
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Since we got support for devices in userspace which allows reporting the
PMU overflow output status to userspace, we should actually allow
creating the PMU on systems without an in-kernel irqchip, which in turn
requires us to slightly clarify error codes for the ABI and move things
around for the initialization phase.
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
We used to extract PRIbits from the ICH_VT_EL2 which was the upper field
in the register word, so a mask wasn't necessary, but as we switched to
looking at PREbits, which is bits 26 through 28 with the PRIbits field
being potentially non-zero, we really need to mask off the field value,
otherwise fun things may happen.
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
The timer work is only scheduled for a VCPU when that VCPU is
blocked. This means we only need to wake it up, not kick (IPI)
it. While calling kvm_vcpu_kick() would just do the wake up,
and not kick, anyway, let's change this to avoid request-less
vcpu kicks, as they're generally not a good idea (see
"Request-less VCPU Kicks" in
Documentation/virtual/kvm/vcpu-requests.rst)
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Refactor PMU overflow handling in order to remove the request-less
vcpu kick. Now, since kvm_vgic_inject_irq() uses vcpu requests,
there should be no chance that a kick sent at just the wrong time
(between the VCPU's call to kvm_pmu_flush_hwstate() and before it
enters guest mode) results in a failure for the guest to see updated
GIC state until its next exit some time later for some other reason.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Don't use request-less VCPU kicks when injecting IRQs, as a VCPU
kick meant to trigger the interrupt injection could be sent while
the VCPU is outside guest mode, which means no IPI is sent, and
after it has called kvm_vgic_flush_hwstate(), meaning it won't see
the updated GIC state until its next exit some time later for some
other reason. The receiving VCPU only needs to check this request
in VCPU RUN to handle it. By checking it, if it's pending, a
memory barrier will be issued that ensures all state is visible.
See "Ensuring Requests Are Seen" of
Documentation/virtual/kvm/vcpu-requests.rst
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
A request called EXIT is too generic. All requests are meant to cause
exits, but different requests have different flags. Let's not make
it difficult to decide if the EXIT request is correct for some case
by just always providing unique requests for each case. This patch
changes EXIT to SLEEP, because that's what the request is asking the
VCPU to do.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Acked-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
We can make a small optimization by not checking the state of
the power_off field on each run. This is done by treating
power_off like pause, only checking it when we get the EXIT
VCPU request. When a VCPU powers off another VCPU the EXIT
request is already made, so we just need to make sure the
request is also made on self power off. kvm_vcpu_kick() isn't
necessary for these cases, as the VCPU would just be kicking
itself, but we add it anyway as a self kick doesn't cost much,
and it makes the code more future-proof.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
System shutdown is currently using request-less VCPU kicks. This
leaves open a tiny race window, as it doesn't ensure the state
change to power_off is seen by a VCPU just about to enter guest
mode. VCPU requests, OTOH, are guaranteed to be seen (see "Ensuring
Requests Are Seen" of Documentation/virtual/kvm/vcpu-requests.rst)
This patch applies the EXIT request used by pause to power_off,
fixing the race.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
The current use of KVM_REQ_VCPU_EXIT for pause is fine. Even the
requester clearing the request is OK, as this is the special case
where the sole requesting thread and receiving VCPU are executing
synchronously (see "Clearing Requests" in
Documentation/virtual/kvm/vcpu-requests.rst) However, that's about
to change, so let's ensure only the receiving VCPU clears the
request. Additionally, by guaranteeing KVM_REQ_VCPU_EXIT is always
set when pause is, we can avoid checking pause directly in VCPU RUN.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
arm/arm64 already has one VCPU request used when setting pause,
but it doesn't properly check requests in VCPU RUN. Check it
and also make sure we set vcpu->mode at the appropriate time
(before the check) and with the appropriate barriers. See
Documentation/virtual/kvm/vcpu-requests.rst. Also make sure we
don't leave any vcpu requests we don't intend to handle later
set in the request bitmap. If we don't clear them, then
kvm_request_pending() may return true when it shouldn't.
Using VCPU requests properly fixes a small race where pause
could get set just as a VCPU was entering guest mode.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
We recently rewrote the sactive and cactive handlers to take the kvm
lock for guest accesses to these registers. However, when accessed from
userspace this lock is already held. Unfortunately we forgot to change
the private accessors for GICv3, because these are redistributor
registers and not distributor registers.
Signed-off-by: Christoffer Dall <cdall@linaro.org>
We have been a little loose with our intermediate VMCR representation
where we had a 'ctlr' field, but we failed to differentiate between the
GICv2 GICC_CTLR and ICC_CTLR_EL1 layouts, and therefore ended up mapping
the wrong bits into the individual fields of the ICH_VMCR_EL2 when
emulating a GICv2 on a GICv3 system.
Fix this by using explicit fields for the VMCR bits instead.
Cc: Eric Auger <eric.auger@redhat.com>
Reported-by: wanghaibin <wanghaibin.wang@huawei.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
We don't need to stop a specific VCPU when changing the active state,
because private IRQs can only be modified by a running VCPU for the
VCPU itself and it is therefore already stopped.
However, it is also possible for two VCPUs to be modifying the active
state of SPIs at the same time, which can cause the thread being stuck
in the loop that checks other VCPU threads for a potentially very long
time, or to modify the active state of a running VCPU. Fix this by
serializing all accesses to setting and clearing the active state of
interrupts using the KVM mutex.
Reported-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Factor out the core register modifier functionality from the entry
points from the register description table, and only call the
prepare/finish functions from the guest path, not the uaccess path.
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
We are about to differentiate between writes from a VCPU and from
userspace to the GIC's GICD_ISACTIVER and GICD_ICACTIVER registers due
to different synchronization requirements.
Expand the macro to define a register description for the GIC to take
uaccess functions as well.
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
We were not holding the kvm->slots_lock as required when calling
kvm_io_bus_unregister_dev() as required.
This only affects the error path, but still, let's do our due
diligence.
Reported by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
If userspace creates the VCPUs after initializing the VGIC, then we end
up in a situation where we trigger a bug in kvm_vcpu_get_idx(), because
it is called prior to adding the VCPU into the vcpus array on the VM.
There is no tight coupling between the VCPU index and the area of the
redistributor region used for the VCPU, so we can simply ensure that all
creations of redistributors are serialized per VM, and increment an
offset when we successfully add a redistributor.
The vgic_register_redist_iodev() function can be called from two paths:
vgic_redister_all_redist_iodev() which is called via the kvm_vgic_addr()
device attribute handler. This patch already holds the kvm->lock mutex.
The other path is via kvm_vgic_vcpu_init, which is called through a
longer chain from kvm_vm_ioctl_create_vcpu(), which releases the
kvm->lock mutex just before calling kvm_arch_vcpu_create(), so we can
simply take this mutex again later for our purposes.
Fixes: ab6f468c10 ("KVM: arm/arm64: Register iodevs when setting redist base and creating VCPUs")
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Tested-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
We yield the kvm->mmu_lock occassionaly while performing an operation
(e.g, unmap or permission changes) on a large area of stage2 mappings.
However this could possibly cause another thread to clear and free up
the stage2 page tables while we were waiting for regaining the lock and
thus the original thread could end up in accessing memory that was
freed. This patch fixes the problem by making sure that the stage2
pagetable is still valid after we regain the lock. The fact that
mmu_notifer->release() could be called twice (via __mmu_notifier_release
and mmu_notifier_unregsister) enhances the possibility of hitting
this race where there are two threads trying to unmap the entire guest
shadow pages.
While at it, cleanup the redudant checks around cond_resched_lock in
stage2_wp_range(), as cond_resched_lock already does the same checks.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: andreyknvl@google.com
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: stable@vger.kernel.org
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Make sure we don't use a cached value of the KVM stage2 PGD while
resetting the PGD.
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
In kvm_free_stage2_pgd() we check the stage2 PGD before holding
the lock and proceed to take the lock if it is valid. And we unmap
the page tables, followed by releasing the lock. We reset the PGD
only after dropping this lock, which could cause a race condition
where another thread waiting on or even holding the lock, could
potentially see that the PGD is still valid and proceed to perform
a stage2 operation and later encounter a NULL PGD.
[223090.242280] Unable to handle kernel NULL pointer dereference at
virtual address 00000040
[223090.262330] PC is at unmap_stage2_range+0x8c/0x428
[223090.262332] LR is at kvm_unmap_hva_handler+0x2c/0x3c
[223090.262531] Call trace:
[223090.262533] [<ffff0000080adb78>] unmap_stage2_range+0x8c/0x428
[223090.262535] [<ffff0000080adf40>] kvm_unmap_hva_handler+0x2c/0x3c
[223090.262537] [<ffff0000080ace2c>] handle_hva_to_gpa+0xb0/0x104
[223090.262539] [<ffff0000080af988>] kvm_unmap_hva+0x5c/0xbc
[223090.262543] [<ffff0000080a2478>]
kvm_mmu_notifier_invalidate_page+0x50/0x8c
[223090.262547] [<ffff0000082274f8>]
__mmu_notifier_invalidate_page+0x5c/0x84
[223090.262551] [<ffff00000820b700>] try_to_unmap_one+0x1d0/0x4a0
[223090.262553] [<ffff00000820c5c8>] rmap_walk+0x1cc/0x2e0
[223090.262555] [<ffff00000820c90c>] try_to_unmap+0x74/0xa4
[223090.262557] [<ffff000008230ce4>] migrate_pages+0x31c/0x5ac
[223090.262561] [<ffff0000081f869c>] compact_zone+0x3fc/0x7ac
[223090.262563] [<ffff0000081f8ae0>] compact_zone_order+0x94/0xb0
[223090.262564] [<ffff0000081f91c0>] try_to_compact_pages+0x108/0x290
[223090.262569] [<ffff0000081d5108>] __alloc_pages_direct_compact+0x70/0x1ac
[223090.262571] [<ffff0000081d64a0>] __alloc_pages_nodemask+0x434/0x9f4
[223090.262572] [<ffff0000082256f0>] alloc_pages_vma+0x230/0x254
[223090.262574] [<ffff000008235e5c>] do_huge_pmd_anonymous_page+0x114/0x538
[223090.262576] [<ffff000008201bec>] handle_mm_fault+0xd40/0x17a4
[223090.262577] [<ffff0000081fb324>] __get_user_pages+0x12c/0x36c
[223090.262578] [<ffff0000081fb804>] get_user_pages_unlocked+0xa4/0x1b8
[223090.262579] [<ffff0000080a3ce8>] __gfn_to_pfn_memslot+0x280/0x31c
[223090.262580] [<ffff0000080a3dd0>] gfn_to_pfn_prot+0x4c/0x5c
[223090.262582] [<ffff0000080af3f8>] kvm_handle_guest_abort+0x240/0x774
[223090.262584] [<ffff0000080b2bac>] handle_exit+0x11c/0x1ac
[223090.262586] [<ffff0000080ab99c>] kvm_arch_vcpu_ioctl_run+0x31c/0x648
[223090.262587] [<ffff0000080a1d78>] kvm_vcpu_ioctl+0x378/0x768
[223090.262590] [<ffff00000825df5c>] do_vfs_ioctl+0x324/0x5a4
[223090.262591] [<ffff00000825e26c>] SyS_ioctl+0x90/0xa4
[223090.262595] [<ffff000008085d84>] el0_svc_naked+0x38/0x3c
This patch moves the stage2 PGD manipulation under the lock.
Reported-by: Alexander Graf <agraf@suse.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
The GICv3 documentation is extremely confusing, as it talks about
the number of priorities represented by the ICH_APxRn_EL2 registers,
while it should really talk about the number of preemption levels.
This leads to a bug where we may access undefined ICH_APxRn_EL2
registers, since PREbits is allowed to be smaller than PRIbits.
Thankfully, nobody seem to have taken this path so far...
The fix is to use ICH_VTR_EL2.PREbits instead.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
When an interrupt is injected with the HW bit set (indicating that
deactivation should be propagated to the physical distributor),
special care must be taken so that we never mark the corresponding
LR with the Active+Pending state (as the pending state is kept in
the physycal distributor).
Cc: stable@vger.kernel.org
Fixes: 59529f69f5 ("KVM: arm/arm64: vgic-new: Add GICv3 world switch backend")
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
When an interrupt is injected with the HW bit set (indicating that
deactivation should be propagated to the physical distributor),
special care must be taken so that we never mark the corresponding
LR with the Active+Pending state (as the pending state is kept in
the physycal distributor).
Cc: stable@vger.kernel.org
Fixes: 140b086dd1 ("KVM: arm/arm64: vgic-new: Add GICv2 world switch backend")
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Changes include:
- A fix related to the 32-bit idmap stub
- A fix to the bitmask used to deode the operands of an AArch32 CP
instruction
- We have moved the files shared between arch/arm/kvm and
arch/arm64/kvm to virt/kvm/arm
- We add support for saving/restoring the virtual ITS state to
userspace
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZEZihAAoJEEtpOizt6ddyGDYH/jmGjDMnryORn2P2o10dUQKJ
RnHTQYnpOYqnprlkFtZFpmK+mjl/a8R1Btb7GK2EwmovTR95pMYPRqtrCTOL0aQA
4OToh7+vFGatwxsGCS6utazdhmx0UT/LhO/GEF4G1zOb7eVa4ZtS1NKLP2WjPD1E
RU3Qn8wa0pESv3tJScv8qo2+PWVX4krbFllhY2Hk0AkVQcI66ExkdVq4ikm1eUXn
rxzIayLG2bv3KEPNCzozdwoY9tDL+b40q6vN/RHGJmM05SZbbSx2/Bkw2RbslSpD
2hvhHWX7xeuEBcd5mZO7sP4WS3hM/BI8eX7q+uMeNJ9B+nM82yjGfOTtglVi2cc=
=JfvQ
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-for-v4.12-round2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
Second round of KVM/ARM Changes for v4.12.
Changes include:
- A fix related to the 32-bit idmap stub
- A fix to the bitmask used to deode the operands of an AArch32 CP
instruction
- We have moved the files shared between arch/arm/kvm and
arch/arm64/kvm to virt/kvm/arm
- We add support for saving/restoring the virtual ITS state to
userspace
When failing to restore the ITT for a DTE, we should remove the failed
device entry from the list and free the object.
We slightly refactor vgic_its_destroy to be able to reuse the now
separate vgic_its_free_dte() function.
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
The only reason we called kvm_vgic_map_resources() when restoring the
ITS tables was because we wanted to have the KVM iodevs registered in
the KVM IO bus framework at the time when the ITS was restored such that
a restored and active device can inject MSIs prior to otherwise calling
kvm_vgic_map_resources() from the first run of a VCPU.
Since we now register the KVM iodevs for the redestributors and ITS as
soon as possible (when setting the base addresses), we no longer need
this call and kvm_vgic_map_resources() is again called only when first
running a VCPU.
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
We have to register the ITS iodevice before running the VM, because in
migration scenarios, we may be restoring a live device that wishes to
inject MSIs before the VCPUs have started.
All we need to register the ITS io device is the base address of the
ITS, so we can simply register that when the base address of the ITS is
set.
[ Code to fix concurrency issues when setting the ITS base address and
to fix the undef base address check written by Marc Zyngier ]
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
The its->initialized doesn't bring much to the table, and creates
unnecessary ordering between setting the address and initializing it
(which amounts to exactly nothing).
Let's kill it altogether, making KVM_DEV_ARM_VGIC_CTRL_INIT the no-op
it deserves to be.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Instead of waiting with registering KVM iodevs until the first VCPU is
run, we can actually create the iodevs when the redist base address is
set. The only downside is that we must now also check if we need to do
this for VCPUs which are created after creating the VGIC, because there
is no enforced ordering between creating the VGIC (and setting its base
addresses) and creating the VCPUs.
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
As we are about to handle setting the address for the redistributor base
region separately from some of the other base addresses, let's rework
this function to leave a little more room for being flexible in what
each type of base address does.
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
As we are about to fiddle with the IO device registration mechanism,
let's be a little more careful when setting base addresses as early as
possible. When setting a base address, we can check that there's
address space enough for its scope and when the last of the two
base addresses (dist and redist) get set, we can also check if the
regions overlap at that time.
This allows us to provide error messages to the user at time when trying
to set the base address, as opposed to later when trying to run the VM.
To do this, we make vgic_v3_check_base available in the core vgic-v3
code as well as in the other parts of the GICv3 code, namely the MMIO
config code.
We also return true for undefined base addresses so that the function
can be used before all base addresses are set; all callers already check
for uninitialized addresses before calling this function.
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Split out the function to register all the redistributor iodevs into a
function that handles a single redistributor at a time in preparation
for being able to call this per VCPU as these get created.
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
The main thing here is a new implementation of the in-kernel
XICS interrupt controller emulation for POWER9 machines, from Ben
Herrenschmidt.
POWER9 has a new interrupt controller called XIVE (eXternal Interrupt
Virtualization Engine) which is able to deliver interrupts directly
to guest virtual CPUs in hardware without hypervisor intervention.
With this new code, the guest still sees the old XICS interface but
performance is better because the XICS emulation in the host uses the
XIVE directly rather than going through a XICS emulation in firmware.
Conflicts:
arch/powerpc/kernel/cpu_setup_power.S [cherry-picked fix]
arch/powerpc/kvm/book3s_xive.c [include asm/debugfs.h]
In vm_stat_get_per_vm_fops and vcpu_stat_get_per_vm_fops, since we
use nonseekable_open() to open, we should use no_llseek() to seek,
not generic_file_llseek().
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This function really doesn't init anything, it enables the CPU
interface, so name it as such, which gives us the name to use for actual
init work later on.
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Merge more updates from Andrew Morton:
- the rest of MM
- various misc things
- procfs updates
- lib/ updates
- checkpatch updates
- kdump/kexec updates
- add kvmalloc helpers, use them
- time helper updates for Y2038 issues. We're almost ready to remove
current_fs_time() but that awaits a btrfs merge.
- add tracepoints to DAX
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (114 commits)
drivers/staging/ccree/ssi_hash.c: fix build with gcc-4.4.4
selftests/vm: add a test for virtual address range mapping
dax: add tracepoint to dax_insert_mapping()
dax: add tracepoint to dax_writeback_one()
dax: add tracepoints to dax_writeback_mapping_range()
dax: add tracepoints to dax_load_hole()
dax: add tracepoints to dax_pfn_mkwrite()
dax: add tracepoints to dax_iomap_pte_fault()
mtd: nand: nandsim: convert to memalloc_noreclaim_*()
treewide: convert PF_MEMALLOC manipulations to new helpers
mm: introduce memalloc_noreclaim_{save,restore}
mm: prevent potential recursive reclaim due to clearing PF_MEMALLOC
mm/huge_memory.c: deposit a pgtable for DAX PMD faults when required
mm/huge_memory.c: use zap_deposited_table() more
time: delete CURRENT_TIME_SEC and CURRENT_TIME
gfs2: replace CURRENT_TIME with current_time
apparmorfs: replace CURRENT_TIME with current_time()
lustre: replace CURRENT_TIME macro
fs: ubifs: replace CURRENT_TIME_SEC with current_time
fs: ufs: use ktime_get_real_ts64() for birthtime
...
Patch series "kvmalloc", v5.
There are many open coded kmalloc with vmalloc fallback instances in the
tree. Most of them are not careful enough or simply do not care about
the underlying semantic of the kmalloc/page allocator which means that
a) some vmalloc fallbacks are basically unreachable because the kmalloc
part will keep retrying until it succeeds b) the page allocator can
invoke a really disruptive steps like the OOM killer to move forward
which doesn't sound appropriate when we consider that the vmalloc
fallback is available.
As it can be seen implementing kvmalloc requires quite an intimate
knowledge if the page allocator and the memory reclaim internals which
strongly suggests that a helper should be implemented in the memory
subsystem proper.
Most callers, I could find, have been converted to use the helper
instead. This is patch 6. There are some more relying on __GFP_REPEAT
in the networking stack which I have converted as well and Eric Dumazet
was not opposed [2] to convert them as well.
[1] http://lkml.kernel.org/r/20170130094940.13546-1-mhocko@kernel.org
[2] http://lkml.kernel.org/r/1485273626.16328.301.camel@edumazet-glaptop3.roam.corp.google.com
This patch (of 9):
Using kmalloc with the vmalloc fallback for larger allocations is a
common pattern in the kernel code. Yet we do not have any common helper
for that and so users have invented their own helpers. Some of them are
really creative when doing so. Let's just add kv[mz]alloc and make sure
it is implemented properly. This implementation makes sure to not make
a large memory pressure for > PAGE_SZE requests (__GFP_NORETRY) and also
to not warn about allocation failures. This also rules out the OOM
killer as the vmalloc is a more approapriate fallback than a disruptive
user visible action.
This patch also changes some existing users and removes helpers which
are specific for them. In some cases this is not possible (e.g.
ext4_kvmalloc, libcfs_kvzalloc) because those seems to be broken and
require GFP_NO{FS,IO} context which is not vmalloc compatible in general
(note that the page table allocation is GFP_KERNEL). Those need to be
fixed separately.
While we are at it, document that __vmalloc{_node} about unsupported gfp
mask because there seems to be a lot of confusion out there.
kvmalloc_node will warn about GFP_KERNEL incompatible (which are not
superset) flags to catch new abusers. Existing ones would have to die
slowly.
[sfr@canb.auug.org.au: f2fs fixup]
Link: http://lkml.kernel.org/r/20170320163735.332e64b7@canb.auug.org.au
Link: http://lkml.kernel.org/r/20170306103032.2540-2-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reviewed-by: Andreas Dilger <adilger@dilger.ca> [ext4 part]
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
support; virtual interrupt controller performance improvements; support
for userspace virtual interrupt controller (slower, but necessary for
KVM on the weird Broadcom SoCs used by the Raspberry Pi 3)
* MIPS: basic support for hardware virtualization (ImgTec
P5600/P6600/I6400 and Cavium Octeon III)
* PPC: in-kernel acceleration for VFIO
* s390: support for guests without storage keys; adapter interruption
suppression
* x86: usual range of nVMX improvements, notably nested EPT support for
accessed and dirty bits; emulation of CPL3 CPUID faulting
* generic: first part of VCPU thread request API; kvm_stat improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJZEHUkAAoJEL/70l94x66DBeYH/09wrpJ2FjU4Rqv7FxmqgWfH
9WGi4wvn/Z+XzQSyfMJiu2SfZVzU69/Y67OMHudy7vBT6knB+ziM7Ntoiu/hUfbG
0g5KsDX79FW15HuvuuGh9kSjUsj7qsQdyPZwP4FW/6ZoDArV9mibSvdjSmiUSMV/
2wxaoLzjoShdOuCe9EABaPhKK0XCrOYkygT6Paz1pItDxaSn8iW3ulaCuWMprUfG
Niq+dFemK464E4yn6HVD88xg5j2eUM6bfuXB3qR3eTR76mHLgtwejBzZdDjLG9fk
32PNYKhJNomBxHVqtksJ9/7cSR6iNPs7neQ1XHemKWTuYqwYQMlPj1NDy0aslQU=
=IsiZ
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"ARM:
- HYP mode stub supports kexec/kdump on 32-bit
- improved PMU support
- virtual interrupt controller performance improvements
- support for userspace virtual interrupt controller (slower, but
necessary for KVM on the weird Broadcom SoCs used by the Raspberry
Pi 3)
MIPS:
- basic support for hardware virtualization (ImgTec P5600/P6600/I6400
and Cavium Octeon III)
PPC:
- in-kernel acceleration for VFIO
s390:
- support for guests without storage keys
- adapter interruption suppression
x86:
- usual range of nVMX improvements, notably nested EPT support for
accessed and dirty bits
- emulation of CPL3 CPUID faulting
generic:
- first part of VCPU thread request API
- kvm_stat improvements"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (227 commits)
kvm: nVMX: Don't validate disabled secondary controls
KVM: put back #ifndef CONFIG_S390 around kvm_vcpu_kick
Revert "KVM: Support vCPU-based gfn->hva cache"
tools/kvm: fix top level makefile
KVM: x86: don't hold kvm->lock in KVM_SET_GSI_ROUTING
KVM: Documentation: remove VM mmap documentation
kvm: nVMX: Remove superfluous VMX instruction fault checks
KVM: x86: fix emulation of RSM and IRET instructions
KVM: mark requests that need synchronization
KVM: return if kvm_vcpu_wake_up() did wake up the VCPU
KVM: add explicit barrier to kvm_vcpu_kick
KVM: perform a wake_up in kvm_make_all_cpus_request
KVM: mark requests that do not need a wakeup
KVM: remove #ifndef CONFIG_S390 around kvm_vcpu_wake_up
KVM: x86: always use kvm_make_request instead of set_bit
KVM: add kvm_{test,clear}_request to replace {test,clear}_bit
s390: kvm: Cpu model support for msa6, msa7 and msa8
KVM: x86: remove irq disablement around KVM_SET_CLOCK/KVM_GET_CLOCK
kvm: better MWAIT emulation for guests
KVM: x86: virtualize cpuid faulting
...
This patch adds a new attribute to GICV3 KVM device
KVM_DEV_ARM_VGIC_GRP_CTRL group. This allows userspace to
flush all GICR pending tables into guest RAM.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
In its_sync_lpi_pending_table() we currently ignore the
target_vcpu of the LPIs. We sync the pending bit found in
the vcpu pending table even if the LPI is not targeting it.
Also in vgic_its_cmd_handle_invall() we are supposed to
read the config table data for the LPIs associated to the
collection ID. At the moment we refresh all LPI config
information.
This patch passes a vpcu to vgic_copy_lpi_list() so that
this latter returns a snapshot of the LPIs targeting this
CPU and only those.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Implement routines to save and restore device ITT and their
interrupt table entries (ITE).
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
This patch saves the device table entries into guest RAM.
Both flat table and 2 stage tables are supported. DeviceId
indexing is used.
For each device listed in the device table, we also save
the translation table using the vgic_its_save/restore_itt
routines. Those functions will be implemented in a subsequent
patch.
On restore, devices are re-allocated and their itt are
re-built.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
As vgic_its_check_id() computes the device/collection entry's
GPA, let's return it so that new callers can retrieve it easily.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Acked-by: Christoffer Dall <cdall@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
The save path copies the collection entries into guest RAM
at the GPA specified in the BASER register. This obviously
requires the BASER to be set. The last written element is a
dummy collection table entry.
We do not index by collection ID as the collection entry
can fit into 8 bytes while containing the collection ID.
On restore path we re-allocate the collection objects.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Add a generic scan_its_table() helper whose role consists in
scanning a contiguous table located in guest RAM and applying
a callback on each entry. Entries can be handled as linked lists
since the callback may return an id offset to the next entry and
also indicate whether the entry is the last one.
Helper functions also are added to compute the device/event ID
offset to the next DTE/ITE.
compute_next_devid_offset, compute_next_eventid_offset and
scan_table will become static in subsequent patches
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Add two new helpers to allocate an its ite and an its device.
This will avoid duplication on restore path.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Introduce new attributes in KVM_DEV_ARM_VGIC_GRP_CTRL group:
- KVM_DEV_ARM_ITS_SAVE_TABLES: saves the ITS tables into guest RAM
- KVM_DEV_ARM_ITS_RESTORE_TABLES: restores them into VGIC internal
structures.
We hold the vcpus lock during the save and restore to make
sure no vcpu is running.
At this stage the functionality is not yet implemented. Only
the skeleton is put in place.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
[Given we will move the iodev register until setting the base addr]
Reviewed-by: Christoffer Dall <cdall@linaro.org>
When creating the lpi we now ask the redistributor what is the state
of the LPI (priority, enabled, pending).
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
this new helper synchronizes the irq pending_latch
with the LPI pending bit status found in rdist pending table.
As the status is consumed, we reset the bit in pending table.
As we need the PENDBASER_ADDRESS() in vgic-v3, let's move its
definition in the irqchip header. We restore the full length
of the field, ie [51:16]. Same for PROPBASER_ADDRESS with full
field length of [51:12].
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
On MAPD we currently check the device id can be stored in the device table.
Let's first check it can be encoded within the range defined by TYPER
DEVBITS.
Also check the collection ID belongs to the 16 bit range as GITS_TYPER
CIL field equals to 0.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Up to now the MAPD ITT_addr had been ignored. We will need it
for save/restore. Let's record it in the its_device struct.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Up to now the MAPD's ITT size field has been ignored. It encodes
the number of eventid bit minus 1. It should be used to check
the eventid when a MAPTI command is issued on a device. Let's
store the number of eventid bits in the its_device and do the
check on MAPTI. Also make sure the ITT size field does
not exceed the GITS_TYPER IDBITS field.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
The GITS_IIDR revision field is used to encode the migration ABI
revision. So we need to restore it to check the table layout is
readable by the destination.
By writing the IIDR, userspace thus forces the ABI revision to be
used and this must be less than or equal to the max revision KVM
supports.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
We plan to support different migration ABIs, ie. characterizing
the ITS table layout format in guest RAM. For example, a new ABI
will be needed if vLPIs get supported for nested use case.
So let's introduce an array of supported ABIs (at the moment a single
ABI is supported though). The following characteristics are foreseen
to vary with the ABI: size of table entries, save/restore operation,
the way abi settings are applied.
By default the MAX_ABI_REV is applied on its creation. In subsequent
patches we will introduce a way for the userspace to change the ABI
in use.
The entry sizes now are set according to the ABI version and not
hardcoded anymore.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
GITS_CREADR needs to be restored so let's implement the associated
uaccess_write_its callback. The write only is allowed if the its
is disabled.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
This patch implements vgic_its_has_attr_regs and vgic_its_attr_regs_access
upon the MMIO framework. VGIC ITS KVM device KVM_DEV_ARM_VGIC_GRP_ITS_REGS
group becomes functional.
At least GITS_CREADR and GITS_IIDR require to differentiate a guest write
action from a user access. As such let's introduce a new uaccess_its_write
vgic_register_region callback.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
We need to use those helpers in vgic-its.c so let's
expose them in the private vgic header.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Christoffer Dall <cdall@linaro.org>
The ITS KVM device exposes a new KVM_DEV_ARM_VGIC_GRP_ITS_REGS
group which allows the userspace to save/restore ITS registers.
At this stage the get/set/has operations are not yet implemented.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
We plan to use vgic_find_mmio_region in vgic-its.c so let's
turn it into a public function.
Also let's take the opportunity to rename the region parameter
into regions to emphasize this latter is an array of regions.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Christoffer Dall <cdall@linaro.org>
The actual abbreviation for the interrupt translation table entry
is ITE. Let's rename all itte instances by ite.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Christoffer Dall <cdall@linaro.org>
- kdump support, including two necessary memblock additions:
memblock_clear_nomap() and memblock_cap_memory_range()
- ARMv8.3 HWCAP bits for JavaScript conversion instructions, complex
numbers and weaker release consistency
- arm64 ACPI platform MSI support
- arm perf updates: ACPI PMU support, L3 cache PMU in some Qualcomm
SoCs, Cortex-A53 L2 cache events and DTLB refills, MAINTAINERS update
for DT perf bindings
- architected timer errata framework (the arch/arm64 changes only)
- support for DMA_ATTR_FORCE_CONTIGUOUS in the arm64 iommu DMA API
- arm64 KVM refactoring to use common system register definitions
- remove support for ASID-tagged VIVT I-cache (no ARMv8 implementation
using it and deprecated in the architecture) together with some
I-cache handling clean-up
- PE/COFF EFI header clean-up/hardening
- define BUG() instruction without CONFIG_BUG
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=SDkm
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
- kdump support, including two necessary memblock additions:
memblock_clear_nomap() and memblock_cap_memory_range()
- ARMv8.3 HWCAP bits for JavaScript conversion instructions, complex
numbers and weaker release consistency
- arm64 ACPI platform MSI support
- arm perf updates: ACPI PMU support, L3 cache PMU in some Qualcomm
SoCs, Cortex-A53 L2 cache events and DTLB refills, MAINTAINERS update
for DT perf bindings
- architected timer errata framework (the arch/arm64 changes only)
- support for DMA_ATTR_FORCE_CONTIGUOUS in the arm64 iommu DMA API
- arm64 KVM refactoring to use common system register definitions
- remove support for ASID-tagged VIVT I-cache (no ARMv8 implementation
using it and deprecated in the architecture) together with some
I-cache handling clean-up
- PE/COFF EFI header clean-up/hardening
- define BUG() instruction without CONFIG_BUG
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (92 commits)
arm64: Fix the DMA mmap and get_sgtable API with DMA_ATTR_FORCE_CONTIGUOUS
arm64: Print DT machine model in setup_machine_fdt()
arm64: pmu: Wire-up Cortex A53 L2 cache events and DTLB refills
arm64: module: split core and init PLT sections
arm64: pmuv3: handle pmuv3+
arm64: Add CNTFRQ_EL0 trap handler
arm64: Silence spurious kbuild warning on menuconfig
arm64: pmuv3: use arm_pmu ACPI framework
arm64: pmuv3: handle !PMUv3 when probing
drivers/perf: arm_pmu: add ACPI framework
arm64: add function to get a cpu's MADT GICC table
drivers/perf: arm_pmu: split out platform device probe logic
drivers/perf: arm_pmu: move irq request/free into probe
drivers/perf: arm_pmu: split cpu-local irq request/free
drivers/perf: arm_pmu: rename irq request/free functions
drivers/perf: arm_pmu: handle no platform_device
drivers/perf: arm_pmu: simplify cpu_pmu_request_irqs()
drivers/perf: arm_pmu: factor out pmu registration
drivers/perf: arm_pmu: fold init into alloc
drivers/perf: arm_pmu: define armpmu_init_fn
...
The #ifndef was removed in 75aaafb79f,
but it was also protecting smp_send_reschedule() in kvm_vcpu_kick().
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
For some time now we have been having a lot of shared functionality
between the arm and arm64 KVM support in arch/arm, which not only
required a horrible inter-arch reference from the Makefile in
arch/arm64/kvm, but also created confusion for newcomers to the code
base, as was recently seen on the mailing list.
Further, it causes confusion for things like cscope, which needs special
attention to index specific shared files for arm64 from the arm tree.
Move the shared files into virt/kvm/arm and move the trace points along
with it. When moving the tracepoints we have to modify the way the vgic
creates definitions of the trace points, so we take the chance to
include the VGIC tracepoints in its very own special vgic trace.h file.
Signed-off-by: Christoffer Dall <cdall@linaro.org>
This reverts commit bbd6411513.
I've been sitting on this revert for too long and it unfortunately
missed 4.11. It's also the reason why I haven't merged ring-based
dirty tracking for 4.12.
Using kvm_vcpu_memslots in kvm_gfn_to_hva_cache_init and
kvm_vcpu_write_guest_offset_cached means that the MSR value can
now be used to access SMRAM, simply by making it point to an SMRAM
physical address. This is problematic because it lets the guest
OS overwrite memory that it shouldn't be able to touch.
Cc: stable@vger.kernel.org
Fixes: bbd6411513
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We needed the lock to avoid racing with creation of the irqchip on x86. As
kvm_set_irq_routing() calls srcu_synchronize_expedited(), this lock
might be held for a longer time.
Let's introduce an arch specific callback to check if we can actually
add irq routes. For x86, all we have to do is check if we have an
irqchip in the kernel. We don't need kvm->lock at that point as the
irqchip is marked as inititalized only when actually fully created.
Reported-by: Steve Rutherford <srutherford@google.com>
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Fixes: 1df6ddede1 ("KVM: x86: race between KVM_SET_GSI_ROUTING and KVM_CREATE_IRQCHIP")
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This merges in the powerpc topic/xive branch to bring in the code for
the in-kernel XICS interrupt controller emulation to use the new XIVE
(eXternal Interrupt Virtualization Engine) hardware in the POWER9 chip
directly, rather than via a XICS emulation in firmware.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Changes include:
- Using the common sysreg definitions between KVM and arm64
- Improved hyp-stub implementation with support for kexec and kdump on the 32-bit side
- Proper PMU exception handling
- Performance improvements of our GIC handling
- Support for irqchip in userspace with in-kernel arch-timers and PMU support
- A fix for a race condition in our PSCI code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJY/IasAAoJEEtpOizt6ddyd7gH/2N3BIMxi/Uqigx0e0byA43s
f+8gNq8A71VBTERGW2l9QP1/AZAXpQYNWdWmN2jn+91x2yoVL7AT00gEsliSLEZv
tqZaTGFXKi1vNihYrxEWm1mfVNzhRrnbW6vjLrO4J5Advq7T3OWhNuVt2BLTxz3Y
h0iqOWNVrUD9h3QSBFH8tz7yXhguDTSppAcXbE0tACdRu4vN50wqEWokHJG5TsMG
Tl3KYWrcc3YCKlAJGuJi7t5rMrXk+g1q6HnxlIN6OSk0POC2Vmw9/Gigtltj1Qwh
ZEAwsnka/U8ak8WaWeZa3EsGTSFSoAk/+pKv2FB8mFN+uOmWDqVlEiol4dW49AY=
=mEOk
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-for-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/ARM Changes for v4.12.
Changes include:
- Using the common sysreg definitions between KVM and arm64
- Improved hyp-stub implementation with support for kexec and kdump on the 32-bit side
- Proper PMU exception handling
- Performance improvements of our GIC handling
- Support for irqchip in userspace with in-kernel arch-timers and PMU support
- A fix for a race condition in our PSCI code
Conflicts:
Documentation/virtual/kvm/api.txt
include/uapi/linux/kvm.h
kvm_make_all_requests() provides a synchronization that waits until all
kicked VCPUs have acknowledged the kick. This is important for
KVM_REQ_MMU_RELOAD as it prevents freeing while lockless paging is
underway.
This patch adds the synchronization property into all requests that are
currently being used with kvm_make_all_requests() in order to preserve
the current behavior and only introduce a new framework. Removing it
from requests where it is not necessary is left for future patches.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
No need to kick a VCPU that we have just woken up.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
kvm_vcpu_kick() must issue a general memory barrier prior to reading
vcpu->mode in order to ensure correctness of the mutual-exclusion
memory barrier pattern used with vcpu->requests. While the cmpxchg
called from kvm_vcpu_kick():
kvm_vcpu_kick
kvm_arch_vcpu_should_kick
kvm_vcpu_exiting_guest_mode
cmpxchg
implies general memory barriers before and after the operation, that
implication is only valid when cmpxchg succeeds. We need an explicit
barrier for when it fails, otherwise a VCPU thread on its entry path
that reads zero for vcpu->requests does not exclude the possibility
the requesting thread sees !IN_GUEST_MODE when it reads vcpu->mode.
kvm_make_all_cpus_request already had a barrier, so we remove it, as
now it would be redundant.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We want to have kvm_make_all_cpus_request() to be an optmized version of
kvm_for_each_vcpu(i, vcpu, kvm) {
kvm_make_request(vcpu, request);
kvm_vcpu_kick(vcpu);
}
and kvm_vcpu_kick() wakes up the target vcpu. We know which requests do
not need the wake up and use it to optimize the loop.
Thanks to that, this patch doesn't change the behavior of current users
(the all don't need the wake up) and only prepares for future where the
wake up is going to be needed.
I think that most requests do not need the wake up, so we would flip the
bit then.
Later on, kvm_make_request() will take care of kicking too, using this
bit to make the decision whether to kick or not.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The #ifndef was protecting a missing halt_wakeup stat, but that is no
longer necessary.
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch makes KVM capable of using the XIVE interrupt controller
to provide the standard PAPR "XICS" style hypercalls. It is necessary
for proper operations when the host uses XIVE natively.
This has been lightly tested on an actual system, including PCI
pass-through with a TG3 device.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[mpe: Cleanup pr_xxx(), unsplit pr_xxx() strings, etc., fix build
failures by adding KVM_XIVE which depends on KVM_XICS and XIVE, and
adding empty stubs for the kvm_xive_xxx() routines, fixup subject,
integrate fixes from Paul for building PR=y HV=n]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This allows the host kernel to handle H_PUT_TCE, H_PUT_TCE_INDIRECT
and H_STUFF_TCE requests targeted an IOMMU TCE table used for VFIO
without passing them to user space which saves time on switching
to user space and back.
This adds H_PUT_TCE/H_PUT_TCE_INDIRECT/H_STUFF_TCE handlers to KVM.
KVM tries to handle a TCE request in the real mode, if failed
it passes the request to the virtual mode to complete the operation.
If it a virtual mode handler fails, the request is passed to
the user space; this is not expected to happen though.
To avoid dealing with page use counters (which is tricky in real mode),
this only accelerates SPAPR TCE IOMMU v2 clients which are required
to pre-register the userspace memory. The very first TCE request will
be handled in the VFIO SPAPR TCE driver anyway as the userspace view
of the TCE table (iommu_table::it_userspace) is not allocated till
the very first mapping happens and we cannot call vmalloc in real mode.
If we fail to update a hardware IOMMU table unexpected reason, we just
clear it and move on as there is nothing really we can do about it -
for example, if we hot plug a VFIO device to a guest, existing TCE tables
will be mirrored automatically to the hardware and there is no interface
to report to the guest about possible failures.
This adds new attribute - KVM_DEV_VFIO_GROUP_SET_SPAPR_TCE - to
the VFIO KVM device. It takes a VFIO group fd and SPAPR TCE table fd
and associates a physical IOMMU table with the SPAPR TCE table (which
is a guest view of the hardware IOMMU table). The iommu_table object
is cached and referenced so we do not have to look up for it in real mode.
This does not implement the UNSET counterpart as there is no use for it -
once the acceleration is enabled, the existing userspace won't
disable it unless a VFIO container is destroyed; this adds necessary
cleanup to the KVM_DEV_VFIO_GROUP_DEL handler.
This advertises the new KVM_CAP_SPAPR_TCE_VFIO capability to the user
space.
This adds real mode version of WARN_ON_ONCE() as the generic version
causes problems with rcu_sched. Since we testing what vmalloc_to_phys()
returns in the code, this also adds a check for already existing
vmalloc_to_phys() call in kvmppc_rm_h_put_tce_indirect().
This finally makes use of vfio_external_user_iommu_id() which was
introduced quite some time ago and was considered for removal.
Tests show that this patch increases transmission speed from 220MB/s
to 750..1020MB/s on 10Gb network (Chelsea CXGB3 10Gb ethernet card).
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
When iterating over the used LRs, be careful not to try to access
an unused LR, or even an unimplemented one if you're unlucky...
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
When emulating a GICv2-on-GICv3, special care must be taken to only
save/restore VMCR_EL2 when ICC_SRE_EL1.SRE is cleared. Otherwise,
all Group-0 interrupts end-up being delivered as FIQ, which is
probably not what the guest expects, as demonstrated here with
an unhappy EFI:
FIQ Exception at 0x000000013BD21CC4
This means that we cannot perform the load/put trick when dealing
with VMCR_EL2 (because the host has SRE set), and we have to deal
with it in the world-switch.
Fortunately, this is not the most common case (modern guests should
be able to deal with GICv3 directly), and the performance is not worse
than what it was before the VMCR optimization.
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Let's drop the goto and return the error value directly.
Suggested-by: Peter Xu <peterx@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Let's rename it into a proper arch specific callback.
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Avoid races between KVM_SET_GSI_ROUTING and KVM_CREATE_IRQCHIP by taking
the kvm->lock when setting up routes.
If KVM_CREATE_IRQCHIP fails, KVM_SET_GSI_ROUTING could have already set
up routes pointing at pic/ioapic, being silently removed already.
Also, as a side effect, this patch makes sure that KVM_SET_GSI_ROUTING
and KVM_CAP_SPLIT_IRQCHIP cannot run in parallel.
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
When not using an in-kernel VGIC, but instead emulating an interrupt
controller in userspace, we should report the PMU overflow status to
that userspace interrupt controller using the KVM_CAP_ARM_USER_IRQ
feature.
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
If you're running with a userspace gic or other interrupt controller
(that is no vgic in the kernel), then you have so far not been able to
use the architected timers, because the output of the architected
timers, which are driven inside the kernel, was a kernel-only construct
between the arch timer code and the vgic.
This patch implements the new KVM_CAP_ARM_USER_IRQ feature, where we use a
side channel on the kvm_run structure, run->s.regs.device_irq_level, to
always notify userspace of the timer output levels when using a userspace
irqchip.
This works by ensuring that before we enter the guest, if the timer
output level has changed compared to what we last told userspace, we
don't enter the guest, but instead return to userspace to notify it of
the new level. If we are exiting, because of an MMIO for example, and
the level changed at the same time, the value is also updated and
userspace can sample the line as it needs. This is nicely achieved
simply always updating the timer_irq_level field after the main run
loop.
Note that the kvm_timer_update_irq trace event is changed to show the
host IRQ number for the timer instead of the guest IRQ number, because
the kernel no longer know which IRQ userspace wires up the timer signal
to.
Also note that this patch implements all required functionality but does
not yet advertise the capability.
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Currently we check if we have an in-kernel irqchip and if the vgic was
properly implemented several places in the arch timer code. But, we
already predicate our enablement of the arm timers on having a valid
and initialized gic, so we can simply check if the timers are enabled or
not.
This also gets rid of the ugly "error that's not an error but used to
signal that the timer shouldn't poke the gic" construct we have.
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
There is no need to call any functions to fold LRs when we don't use any
LRs and we don't need to mess with overflow flags, take spinlocks, or
prune the AP list if the AP list is empty.
Note: list_empty is a single atomic read (uses READ_ONCE) and can
therefore check if a list is empty or not without the need to take the
spinlock protecting the list.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Now when we do an early init of the static parts of the VGIC data
structures, we can do things like checking if the AP lists are empty
directly without having to explicitly check if the vgic is initialized
and reduce a bit of work in our critical path.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Implement early initialization for both the distributor and the CPU
interfaces. The basic idea is that even though the VGIC is not
functional or not requested from user space, the critical path of the
run loop can still call VGIC functions that just won't do anything,
without them having to check additional initialization flags to ensure
they don't look at uninitialized data structures.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
We don't use these fields anymore so let's nuke them completely.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Now when we don't look at the MISR and EISR values anymore, we can get
rid of the logic to save them in the GIC save/restore code.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Since we always read back the LRs that we wrote to the guest and the
MISR and EISR registers simply provide a summary of the configuration of
the bits in the LRs, there is really no need to read back those status
registers and process them. We might as well just signal the
notifyfd when folding the LR state and save some cycles in the process.
We now clear the underflow bit in the fold_lr_state functions as we only
need to clear this bit if we had used all the LRs, so this is as good a
place as any to do that work.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
We currently assume that all the interrupts in our AP list will be
queued to LRs, but that's not necessarily the case, because some of them
could have been migrated away to different VCPUs and only the VCPU
thread itself can remove interrupts from its AP list.
Therefore, slightly change the logic to only setting the underflow
interrupt when we actually run out of LRs.
As it turns out, this allows us to further simplify the handling in
vgic_sync_hwstate in later patches.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
There is no need to calculate and maintain live_lrs when we always
populate the lowest numbered LRs first on every entry and clear all LRs
on every exit.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
We do not need to flush vgic states in each world switch unless
there is pending IRQ queued to the vgic's ap list. We can thus reduce
the overhead by not grabbing the spinlock and not making the extra
function call to vgic_flush_lr_state.
Note: list_empty is a single atomic read (uses READ_ONCE) and can
therefore check if a list is empty or not without the need to take the
spinlock protecting the list.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Shih-Wei Li <shihwei@cs.columbia.edu>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
We don't have to save/restore the VMCR on every entry to/from the guest,
since on GICv2 we can access the control interface from EL1 and on VHE
systems with GICv3 we can access the control interface from KVM running
in EL2.
GICv3 systems without VHE becomes the rare case, which has to
save/restore the register on each round trip.
Note that userspace accesses may see out-of-date values if the VCPU is
running while accessing the VGIC state via the KVM device API, but this
is already the case and it is up to userspace to quiesce the CPUs before
reading the CPU registers from the GIC for an up-to-date view.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@cs.columbia.edu>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Its value has never changed; we might as well make it part of the ABI instead
of using the return value of KVM_CHECK_EXTENSION(KVM_CAP_COALESCED_MMIO).
Because PPC does not always make MMIO available, the code has to be made
dependent on CONFIG_KVM_MMIO rather than KVM_COALESCED_MMIO_PAGE_OFFSET.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Remove code from architecture files that can be moved to virt/kvm, since there
is already common code for coalesced MMIO.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
[Removed a pointless 'break' after 'return'.]
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Legacy device assignment has been deprecated since 4.2 (released
1.5 years ago). VFIO is better and everyone should have switched to it.
If they haven't, this should convince them. :)
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Fixes include:
- Fix a problem with GICv3 userspace save/restore
- Clarify GICv2 userspace save/restore ABI
- Be more careful in clearing GIC LRs
- Add missing synchronization primitive to our MMU handling code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJY5MItAAoJEEtpOizt6ddy4mUH/1Z2rt2mUAYFQpWD/vy9WMxf
zJKMtcLlZZGjeU78zFfWuOxEo1bbDO+tOTV1docNnY8xjyszCZ5XKOqMeo2a7Vfh
1QYHxJTOmgxcRmMsOnJpqUXhhYm9hDxrbU88U/wvoNllLjWBea01ZXiJbWFPBssT
jrdtcCVstDGp3x3D91RgYNNzj9jNw80RBekACZZwYokDRpBZyUb8DYKfUgABFEKT
UPiHrxb8UOVqvbCuXMBNzhUZcuMoAh3oY02R9sV7u1QOXAJYfRV4fOV12fIcYbHf
tnyU8cCxEkSI1pHrpVG6SStcMt8yznQ+UPo0okQNBJXim2yI8+QKHtQlvx7Tjo8=
=tPDd
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-for-v4.11-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm
From: Christoffer Dall <cdall@linaro.org>
KVM/ARM Fixes for v4.11-rc6
Fixes include:
- Fix a problem with GICv3 userspace save/restore
- Clarify GICv2 userspace save/restore ABI
- Be more careful in clearing GIC LRs
- Add missing synchronization primitive to our MMU handling code
As an oversight, for GICv2, we accidentally export the GICC_PMR register
in the format of the GICH_VMCR.VMPriMask field in the lower 5 bits of a
word, meaning that userspace must always use the lower 5 bits to
communicate with the KVM device and must shift the value left by 3
places to obtain the actual priority mask level.
Since GICv3 supports the full 8 bits of priority masking in the ICH_VMCR,
we have to fix the value we export when emulating a GICv2 on top of a
hardware GICv3 and exporting the emulated GICv2 state to userspace.
Take the chance to clarify this aspect of the ABI.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
We currently have some code to clear the list registers on GICv3, but we
never call this code, because the caller got nuked when removing the old
vgic. We also used to have a similar GICv2 part, but that got lost in
the process too.
Let's reintroduce the logic for GICv2 and call the logic when we
initialize the use of hypervisors on the CPU, for example when first
loading KVM or when exiting a low power state.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
or VM memory are not put thus leaked in kvm_iommu_unmap_memslots() when
destroy VM.
This is consistent with current vfio implementation.
Signed-off-by: herongguang <herongguang.he@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
No caller currently checks the return value of
kvm_io_bus_unregister_dev(). This is evil, as all callers silently go on
freeing their device. A stale reference will remain in the io_bus,
getting at least used again, when the iobus gets teared down on
kvm_destroy_vm() - leading to use after free errors.
There is nothing the callers could do, except retrying over and over
again.
So let's simply remove the bus altogether, print an error and make
sure no one can access this broken bus again (returning -ENOMEM on any
attempt to access it).
Fixes: e93f8a0f82 ("KVM: convert io_bus to SRCU")
Cc: stable@vger.kernel.org # 3.4+
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The kvm_vgic_global_state struct contains a static key which is
written to by jump_label_init() at boot time. So in preparation of
making .text regions truly (well, almost truly) read-only, mark
kvm_vgic_global_state __ro_after_init so it moves to the .rodata
section instead.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Laura Abbott <labbott@redhat.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
When releasing the bus, let's clear the bus pointers to mark it out. If
any further device unregister happens on this bus, we know that we're
done if we found the bus being released already.
Signed-off-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
The ITS spec says that ITS commands are only processed when the ITS
is enabled (section 8.19.4, Enabled, bit[0]). Our emulation was not taking
this into account.
Fix this by checking the enabled state before handling CWRITER writes.
On the other hand that means that CWRITER could advance while the ITS
is disabled, and enabling it would need those commands to be processed.
Fix this case as well by refactoring actual command processing and
calling this from both the GITS_CWRITER and GITS_CTLR handlers.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Currently, if a vcpu thread tries to change the active state of an
interrupt which is already on the same vcpu's AP list, it will loop
forever. Since the VGIC mmio handler is called after a vcpu has
already synced back the LR state to the struct vgic_irq, we can just
let it proceed safely.
Cc: stable@vger.kernel.org
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Jintack Lim <jintack@cs.columbia.edu>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Our GICv3 emulation always presents ICC_SRE_EL1 with DIB/DFB set to
zero, which implies that there is a way to bypass the GIC and
inject raw IRQ/FIQ by driving the CPU pins.
Of course, we don't allow that when the GIC is configured, but
we fail to indicate that to the guest. The obvious fix is to
set these bits (and never let them being changed again).
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
PPC:
* correct assumption about ASDR on POWER9
* fix MMIO emulation on POWER9
x86:
* add a simple test for ioperm
* cleanup TSS
(going through KVM tree as the whole undertaking was caused by VMX's
use of TSS)
* fix nVMX interrupt delivery
* fix some performance counters in the guest
And two cleanup patches.
-----BEGIN PGP SIGNATURE-----
iQEcBAABCAAGBQJYuu5qAAoJEED/6hsPKofoRAUH/jkx/KFDcw3FggixysWVgRai
iLSbbAZemnSLFSOkOU/t7Bz0fXCUgB0tAcMJd9ow01Dg1zObiTpuUIo6qEPaYHdX
gqtUzlHuyECZEcgK0RXS9kDYLrvw7EFocxnDWQfV91qCZSS6nBSSLF3ST1rNV69W
mUvcZG+MciDcZUe1lTexoswVTh1m7avvozEnQ5OHnZR9yicoXiadBQjzL6yqWoqf
Ml/29zRk5+MvloTudxjkAKm3mh7psW88jNMh37TXbAA7i+Xwl9cU6GLR9mFWstoP
7Ot7ecq9mNAUO3lTIQh7lqvB60LMFznS4IlYK7MbplC3kvJLkfzhTWaN1aGvh90=
=cqHo
-----END PGP SIGNATURE-----
Merge tag 'kvm-4.11-2' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull more KVM updates from Radim Krčmář:
"Second batch of KVM changes for the 4.11 merge window:
PPC:
- correct assumption about ASDR on POWER9
- fix MMIO emulation on POWER9
x86:
- add a simple test for ioperm
- cleanup TSS (going through KVM tree as the whole undertaking was
caused by VMX's use of TSS)
- fix nVMX interrupt delivery
- fix some performance counters in the guest
... and two cleanup patches"
* tag 'kvm-4.11-2' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: nVMX: Fix pending events injection
x86/kvm/vmx: remove unused variable in segment_base()
selftests/x86: Add a basic selftest for ioperm
x86/asm: Tidy up TSS limit code
kvm: convert kvm.users_count from atomic_t to refcount_t
KVM: x86: never specify a sample period for virtualized in_tx_cp counters
KVM: PPC: Book3S HV: Don't use ASDR for real-mode HPT faults on POWER9
KVM: PPC: Book3S HV: Fix software walk of guest process page tables
We are going to split <linux/sched/stat.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/stat.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Fix up affected files that include this signal functionality via sched.h.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to split <linux/sched/mm.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/mm.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
The APIs that are going to be moved first are:
mm_alloc()
__mmdrop()
mmdrop()
mmdrop_async_fn()
mmdrop_async()
mmget_not_zero()
mmput()
mmput_async()
get_task_mm()
mm_access()
mm_release()
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Apart from adding the helper function itself, the rest of the kernel is
converted mechanically using:
git grep -l 'atomic_inc.*mm_users' | xargs sed -i 's/atomic_inc(&\(.*\)->mm_users);/mmget\(\1\);/'
git grep -l 'atomic_inc.*mm_users' | xargs sed -i 's/atomic_inc(&\(.*\)\.mm_users);/mmget\(\&\1\);/'
This is needed for a later patch that hooks into the helper, but might
be a worthwhile cleanup on its own.
(Michal Hocko provided most of the kerneldoc comment.)
Link: http://lkml.kernel.org/r/20161218123229.22952-2-vegard.nossum@oracle.com
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Apart from adding the helper function itself, the rest of the kernel is
converted mechanically using:
git grep -l 'atomic_inc.*mm_count' | xargs sed -i 's/atomic_inc(&\(.*\)->mm_count);/mmgrab\(\1\);/'
git grep -l 'atomic_inc.*mm_count' | xargs sed -i 's/atomic_inc(&\(.*\)\.mm_count);/mmgrab\(\&\1\);/'
This is needed for a later patch that hooks into the helper, but might
be a worthwhile cleanup on its own.
(Michal Hocko provided most of the kerneldoc comment.)
Link: http://lkml.kernel.org/r/20161218123229.22952-1-vegard.nossum@oracle.com
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
->fault(), ->page_mkwrite(), and ->pfn_mkwrite() calls do not need to
take a vma and vmf parameter when the vma already resides in vmf.
Remove the vma parameter to simplify things.
[arnd@arndb.de: fix ARM build]
Link: http://lkml.kernel.org/r/20170125223558.1451224-1-arnd@arndb.de
Link: http://lkml.kernel.org/r/148521301778.19116.10840599906674778980.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Darrick J. Wong <darrick.wong@oracle.com>
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jan Kara <jack@suse.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* Return an error code without storing it in an intermediate variable.
* Delete the local variable "r" and the jump label "out" which became
unnecessary with this refactoring.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
* Return an error code without storing it in an intermediate variable.
* Delete the local variable "r" and the jump label "out" which became
unnecessary with this refactoring.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
* Return directly after a call of the function "copy_from_user" failed
in a case block.
This issue was detected by using the Coccinelle software.
* Delete the jump label "out" which became unnecessary with
this refactoring.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Provide versions of struct gfn_to_hva_cache functions that
take vcpu as a parameter instead of struct kvm. The existing functions
are not needed anymore, so delete them. This allows dirty pages to
be logged in the vcpu dirty ring, instead of the global dirty ring,
for ring-based dirty memory tracking.
Signed-off-by: Lei Cao <lei.cao@stratus.com>
Message-Id: <CY1PR08MB19929BD2AC47A291FD680E83F04F0@CY1PR08MB1992.namprd08.prod.outlook.com>
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This will make it easier to support multiple address spaces in
kvm_gfn_to_hva_cache_init. Instead of having to check the address
space id, we can keep on checking just the generation number.
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This will make it a bit simpler to handle multiple address spaces
in gfn_to_hva_cache.
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Emulate read and write operations to CNTP_TVAL, CNTP_CVAL and CNTP_CTL.
Now VMs are able to use the EL1 physical timer.
Signed-off-by: Jintack Lim <jintack@cs.columbia.edu>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Set a background timer for the EL1 physical timer emulation while VMs
are running, so that VMs get the physical timer interrupts in a timely
manner.
Schedule the background timer on entry to the VM and cancel it on exit.
This would not have any performance impact to the guest OSes that
currently use the virtual timer since the physical timer is always not
enabled.
Signed-off-by: Jintack Lim <jintack@cs.columbia.edu>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
When scheduling a background timer, consider both of the virtual and
physical timer and pick the earliest expiration time.
Signed-off-by: Jintack Lim <jintack@cs.columbia.edu>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Now that we maintain the EL1 physical timer register states of VMs,
update the physical timer interrupt level along with the virtual one.
Signed-off-by: Jintack Lim <jintack@cs.columbia.edu>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Initialize the emulated EL1 physical timer with the default irq number.
Signed-off-by: Jintack Lim <jintack@cs.columbia.edu>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Now that we have a separate structure for timer context, make functions
generic so that they can work with any timer context, not just the
virtual timer context. This does not change the virtual timer
functionality.
Signed-off-by: Jintack Lim <jintack@cs.columbia.edu>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Make cntvoff per each timer context. This is helpful to abstract kvm
timer functions to work with timer context without considering timer
types (e.g. physical timer or virtual timer).
This also would pave the way for ever doing adjustments of the cntvoff
on a per-CPU basis if that should ever make sense.
Signed-off-by: Jintack Lim <jintack@cs.columbia.edu>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Abstract virtual timer context into a separate structure and change all
callers referring to timer registers, irq state and so on. No change in
functionality.
This is about to become very handy when adding the EL1 physical timer.
Signed-off-by: Jintack Lim <jintack@cs.columbia.edu>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The IRQFD framework calls the architecture dependent function
twice if the corresponding GSI type is edge triggered. For ARM,
the function kvm_set_msi() is getting called twice whenever the
IRQFD receives the event signal. The rest of the code path is
trying to inject the MSI without any validation checks. No need
to call the function vgic_its_inject_msi() second time to avoid
an unnecessary overhead in IRQ queue logic. It also avoids the
possibility of VM seeing the MSI twice.
Simple fix, return -1 if the argument 'level' value is zero.
Cc: stable@vger.kernel.org
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The only benefit of having kvm_vgic_inject_mapped_irq separate from
kvm_vgic_inject_irq is that we pass a boolean that we use for error
checking on the injection path.
While this could potentially help in some aspect of robustness, it's
also a little bit of a defensive move, and arguably callers into the
vgic should have make sure they have marked their virtual IRQs as mapped
if required.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Userspace requires to store and restore of line_level for
level triggered interrupts using ioctl KVM_DEV_ARM_VGIC_GRP_LEVEL_INFO.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Vijaya Kumar K <Vijaya.Kumar@cavium.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
VGICv3 CPU interface registers are accessed using
KVM_DEV_ARM_VGIC_CPU_SYSREGS ioctl. These registers are accessed
as 64-bit. The cpu MPIDR value is passed along with register id.
It is used to identify the cpu for registers access.
The VM that supports SEIs expect it on destination machine to handle
guest aborts and hence checked for ICC_CTLR_EL1.SEIS compatibility.
Similarly, VM that supports Affinity Level 3 that is required for AArch64
mode, is required to be supported on destination machine. Hence checked
for ICC_CTLR_EL1.A3V compatibility.
The arch/arm64/kvm/vgic-sys-reg-v3.c handles read and write of VGIC
CPU registers for AArch64.
For AArch32 mode, arch/arm/kvm/vgic-v3-coproc.c file is created but
APIs are not implemented.
Updated arch/arm/include/uapi/asm/kvm.h with new definitions
required to compile for AArch32.
The version of VGIC v3 specification is defined here
Documentation/virtual/kvm/devices/arm-vgic-v3.txt
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: Vijaya Kumar K <Vijaya.Kumar@cavium.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
ICC_VMCR_EL2 supports virtual access to ICC_IGRPEN1_EL1.Enable
and ICC_IGRPEN0_EL1.Enable fields. Add grpen0 and grpen1 member
variables to struct vmcr to support read and write of these fields.
Also refactor vgic_set_vmcr and vgic_get_vmcr() code.
Drop ICH_VMCR_CTLR_SHIFT and ICH_VMCR_CTLR_MASK macros and instead
use ICH_VMCR_EOI* and ICH_VMCR_CBPR* macros.
Signed-off-by: Vijaya Kumar K <Vijaya.Kumar@cavium.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
VGICv3 Distributor and Redistributor registers are accessed using
KVM_DEV_ARM_VGIC_GRP_DIST_REGS and KVM_DEV_ARM_VGIC_GRP_REDIST_REGS
with KVM_SET_DEVICE_ATTR and KVM_GET_DEVICE_ATTR ioctls.
These registers are accessed as 32-bit and cpu mpidr
value passed along with register offset is used to identify the
cpu for redistributor registers access.
The version of VGIC v3 specification is defined here
Documentation/virtual/kvm/devices/arm-vgic-v3.txt
Also update arch/arm/include/uapi/asm/kvm.h to compile for
AArch32 mode.
Signed-off-by: Vijaya Kumar K <Vijaya.Kumar@cavium.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Read and write of some registers like ISPENDR and ICPENDR
from userspace requires special handling when compared to
guest access for these registers.
Refer to Documentation/virtual/kvm/devices/arm-vgic-v3.txt
for handling of ISPENDR, ICPENDR registers handling.
Add infrastructure to support guest and userspace read
and write for the required registers
Also moved vgic_uaccess from vgic-mmio-v2.c to vgic-mmio.c
Signed-off-by: Vijaya Kumar K <Vijaya.Kumar@cavium.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add a file to debugfs to read the in-kernel state of the vgic. We don't
do any locking of the entire VGIC state while traversing all the IRQs,
so if the VM is running the user/developer may not see a quiesced state,
but should take care to pause the VM using facilities in user space for
that purpose.
We also don't support LPIs yet, but they can be added easily if needed.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
One of the goals behind the VGIC redesign was to get rid of cached or
intermediate state in the data structures, but we decided to allow
ourselves to precompute the pending value of an IRQ based on the line
level and pending latch state. However, this has now become difficult
to base proper GICv3 save/restore on, because there is a potential to
modify the pending state without knowing if an interrupt is edge or
level configured.
See the following post and related message for more background:
https://lists.cs.columbia.edu/pipermail/kvmarm/2017-January/023195.html
This commit gets rid of the precomputed pending field in favor of a
function that calculates the value when needed, irq_is_pending().
The soft_pending field is renamed to pending_latch to represent that
this latch is the equivalent hardware latch which gets manipulated by
the input signal for edge-triggered interrupts and when writing to the
SPENDR/CPENDR registers.
After this commit save/restore code should be able to simply restore the
pending_latch state, line_level state, and config state in any order and
get the desired result.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
- Fix for timer setup on VHE machines
- Drop spurious warning when the timer races against
the vcpu running again
- Prevent a vgic deadlock when the initialization fails
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7cIH
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-for-4.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm
KVM/ARM updates for 4.10-rc4
- Fix for timer setup on VHE machines
- Drop spurious warning when the timer races against
the vcpu running again
- Prevent a vgic deadlock when the initialization fails
Dmitry Vyukov reported that the syzkaller fuzzer triggered a
deadlock in the vgic setup code when an error was detected, as
the cleanup code tries to take a lock that is already held by
the setup code.
The fix is to avoid retaking the lock when cleaning up, by
telling the cleanup function that we already hold it.
Cc: stable@vger.kernel.org
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Current KVM world switch code is unintentionally setting wrong bits to
CNTHCTL_EL2 when E2H == 1, which may allow guest OS to access physical
timer. Bit positions of CNTHCTL_EL2 are changing depending on
HCR_EL2.E2H bit. EL1PCEN and EL1PCTEN are 1st and 0th bits when E2H is
not set, but they are 11th and 10th bits respectively when E2H is set.
In fact, on VHE we only need to set those bits once, not for every world
switch. This is because the host kernel runs in EL2 with HCR_EL2.TGE ==
1, which makes those bits have no effect for the host kernel execution.
So we just set those bits once for guests, and that's it.
Signed-off-by: Jintack Lim <jintack@cs.columbia.edu>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
When a VCPU blocks (WFI) and has programmed the vtimer, we program a
soft timer to expire in the future to wake up the vcpu thread when
appropriate. Because such as wake up involves a vcpu kick, and the
timer expire function can get called from interrupt context, and the
kick may sleep, we have to schedule the kick in the work function.
The work function currently has a warning that gets raised if it turns
out that the timer shouldn't fire when it's run, which was added because
the idea was that in that case the work should never have been cancelled.
However, it turns out that this whole thing is racy and we can get
spurious warnings. The problem is that we clear the armed flag in the
work function, which may run in parallel with the
kvm_timer_unschedule->timer_disarm() call. This results in a possible
situation where the timer_disarm() call does not call
cancel_work_sync(), which effectively synchronizes the completion of the
work function with running the VCPU. As a result, the VCPU thread
proceeds before the work function completees, causing changes to the
timer state such that kvm_timer_should_fire(vcpu) returns false in the
work function.
All we do in the work function is to kick the VCPU, and an occasional
rare extra kick never harmed anyone. Since the race above is extremely
rare, we don't bother checking if the race happens but simply remove the
check and the clearing of the armed flag from the work function.
Reported-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reported syzkaller:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000008
IP: irq_bypass_unregister_consumer+0x9d/0xb70 [irqbypass]
PGD 0
Oops: 0002 [#1] SMP
CPU: 1 PID: 125 Comm: kworker/1:1 Not tainted 4.9.0+ #1
Workqueue: kvm-irqfd-cleanup irqfd_shutdown [kvm]
task: ffff9bbe0dfbb900 task.stack: ffffb61802014000
RIP: 0010:irq_bypass_unregister_consumer+0x9d/0xb70 [irqbypass]
Call Trace:
irqfd_shutdown+0x66/0xa0 [kvm]
process_one_work+0x16b/0x480
worker_thread+0x4b/0x500
kthread+0x101/0x140
? process_one_work+0x480/0x480
? kthread_create_on_node+0x60/0x60
ret_from_fork+0x25/0x30
RIP: irq_bypass_unregister_consumer+0x9d/0xb70 [irqbypass] RSP: ffffb61802017e20
CR2: 0000000000000008
The syzkaller folks reported a NULL pointer dereference that due to
unregister an consumer which fails registration before. The syzkaller
creates two VMs w/ an equal eventfd occasionally. So the second VM
fails to register an irqbypass consumer. It will make irqfd as inactive
and queue an workqueue work to shutdown irqfd and unregister the irqbypass
consumer when eventfd is closed. However, the second consumer has been
initialized though it fails registration. So the token(same as the first
VM's) is taken to unregister the consumer through the workqueue, the
consumer of the first VM is found and unregistered, then NULL deref incurred
in the path of deleting consumer from the consumers list.
This patch fixes it by making irq_bypass_register/unregister_consumer()
looks for the consumer entry based on consumer pointer itself instead of
token matching.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Suggested-by: Alex Williamson <alex.williamson@redhat.com>
Cc: stable@vger.kernel.org
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Pull timer type cleanups from Thomas Gleixner:
"This series does a tree wide cleanup of types related to
timers/timekeeping.
- Get rid of cycles_t and use a plain u64. The type is not really
helpful and caused more confusion than clarity
- Get rid of the ktime union. The union has become useless as we use
the scalar nanoseconds storage unconditionally now. The 32bit
timespec alike storage got removed due to the Y2038 limitations
some time ago.
That leaves the odd union access around for no reason. Clean it up.
Both changes have been done with coccinelle and a small amount of
manual mopping up"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
ktime: Get rid of ktime_equal()
ktime: Cleanup ktime_set() usage
ktime: Get rid of the union
clocksource: Use a plain u64 instead of cycle_t
Pull SMP hotplug notifier removal from Thomas Gleixner:
"This is the final cleanup of the hotplug notifier infrastructure. The
series has been reintgrated in the last two days because there came a
new driver using the old infrastructure via the SCSI tree.
Summary:
- convert the last leftover drivers utilizing notifiers
- fixup for a completely broken hotplug user
- prevent setup of already used states
- removal of the notifiers
- treewide cleanup of hotplug state names
- consolidation of state space
There is a sphinx based documentation pending, but that needs review
from the documentation folks"
* 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/armada-xp: Consolidate hotplug state space
irqchip/gic: Consolidate hotplug state space
coresight/etm3/4x: Consolidate hotplug state space
cpu/hotplug: Cleanup state names
cpu/hotplug: Remove obsolete cpu hotplug register/unregister functions
staging/lustre/libcfs: Convert to hotplug state machine
scsi/bnx2i: Convert to hotplug state machine
scsi/bnx2fc: Convert to hotplug state machine
cpu/hotplug: Prevent overwriting of callbacks
x86/msr: Remove bogus cleanup from the error path
bus: arm-ccn: Prevent hotplug callback leak
perf/x86/intel/cstate: Prevent hotplug callback leak
ARM/imx/mmcd: Fix broken cpu hotplug handling
scsi: qedi: Convert to hotplug state machine
There is no point in having an extra type for extra confusion. u64 is
unambiguous.
Conversion was done with the following coccinelle script:
@rem@
@@
-typedef u64 cycle_t;
@fix@
typedef cycle_t;
@@
-cycle_t
+u64
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: John Stultz <john.stultz@linaro.org>
When the state names got added a script was used to add the extra argument
to the calls. The script basically converted the state constant to a
string, but the cleanup to convert these strings into meaningful ones did
not happen.
Replace all the useless strings with 'subsys/xxx/yyy:state' strings which
are used in all the other places already.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Link: http://lkml.kernel.org/r/20161221192112.085444152@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Unexport the low-level __get_user_pages_unlocked() function and replaces
invocations with calls to more appropriate higher-level functions.
In hva_to_pfn_slow() we are able to replace __get_user_pages_unlocked()
with get_user_pages_unlocked() since we can now pass gup_flags.
In async_pf_execute() and process_vm_rw_single_vec() we need to pass
different tsk, mm arguments so get_user_pages_remote() is the sane
replacement in these cases (having added manual acquisition and release
of mmap_sem.)
Additionally get_user_pages_remote() reintroduces use of the FOLL_TOUCH
flag. However, this flag was originally silently dropped by commit
1e9877902d ("mm/gup: Introduce get_user_pages_remote()"), so this
appears to have been unintentional and reintroducing it is therefore not
an issue.
[akpm@linux-foundation.org: coding-style fixes]
Link: http://lkml.kernel.org/r/20161027095141.2569-3-lstoakes@gmail.com
Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Hugh Dickins <hughd@google.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krcmar <rkrcmar@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
x86: userspace can now hide nested VMX features from guests; nested
VMX can now run Hyper-V in a guest; support for AVX512_4VNNIW and
AVX512_FMAPS in KVM; infrastructure support for virtual Intel GPUs.
PPC: support for KVM guests on POWER9; improved support for interrupt
polling; optimizations and cleanups.
s390: two small optimizations, more stuff is in flight and will be
in 4.11.
ARM: support for the GICv3 ITS on 32bit platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQExBAABCAAbBQJYTkP0FBxwYm9uemluaUByZWRoYXQuY29tAAoJEL/70l94x66D
lZIH/iT1n9OQXcuTpYYnQhuCenzI3GZZOIMTbCvK2i5bo0FIJKxVn0EiAAqZSXvO
nO185FqjOgLuJ1AD1kJuxzye5suuQp4HIPWWgNHcexLuy43WXWKZe0IQlJ4zM2Xf
u31HakpFmVDD+Cd1qN3yDXtDrRQ79/xQn2kw7CWb8olp+pVqwbceN3IVie9QYU+3
gCz0qU6As0aQIwq2PyalOe03sO10PZlm4XhsoXgWPG7P18BMRhNLTDqhLhu7A/ry
qElVMANT7LSNLzlwNdpzdK8rVuKxETwjlc1UP8vSuhrwad4zM2JJ1Exk26nC2NaG
D0j4tRSyGFIdx6lukZm7HmiSHZ0=
=mkoB
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"Small release, the most interesting stuff is x86 nested virt
improvements.
x86:
- userspace can now hide nested VMX features from guests
- nested VMX can now run Hyper-V in a guest
- support for AVX512_4VNNIW and AVX512_FMAPS in KVM
- infrastructure support for virtual Intel GPUs.
PPC:
- support for KVM guests on POWER9
- improved support for interrupt polling
- optimizations and cleanups.
s390:
- two small optimizations, more stuff is in flight and will be in
4.11.
ARM:
- support for the GICv3 ITS on 32bit platforms"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (94 commits)
arm64: KVM: pmu: Reset PMSELR_EL0.SEL to a sane value before entering the guest
KVM: arm/arm64: timer: Check for properly initialized timer on init
KVM: arm/arm64: vgic-v2: Limit ITARGETSR bits to number of VCPUs
KVM: x86: Handle the kthread worker using the new API
KVM: nVMX: invvpid handling improvements
KVM: nVMX: check host CR3 on vmentry and vmexit
KVM: nVMX: introduce nested_vmx_load_cr3 and call it on vmentry
KVM: nVMX: propagate errors from prepare_vmcs02
KVM: nVMX: fix CR3 load if L2 uses PAE paging and EPT
KVM: nVMX: load GUEST_EFER after GUEST_CR0 during emulated VM-entry
KVM: nVMX: generate MSR_IA32_CR{0,4}_FIXED1 from guest CPUID
KVM: nVMX: fix checks on CR{0,4} during virtual VMX operation
KVM: nVMX: support restore of VMX capability MSRs
KVM: nVMX: generate non-true VMX MSRs based on true versions
KVM: x86: Do not clear RFLAGS.TF when a singlestep trap occurs.
KVM: x86: Add kvm_skip_emulated_instruction and use it.
KVM: VMX: Move skip_emulated_instruction out of nested_vmx_check_vmcs12
KVM: VMX: Reorder some skip_emulated_instruction calls
KVM: x86: Add a return value to kvm_emulate_cpuid
KVM: PPC: Book3S: Move prototypes for KVM functions into kvm_ppc.h
...
- VFIO updates for v4.10 primarily include a new Mediated Device
interface, which essentially allows software defined devices to be
exposed to users through VFIO. The host vendor driver providing
this virtual device polices, or mediates user access to the device.
These devices often incorporate portions of real devices, for
instance the primary initial users of this interface expose vGPUs
which allow the user to map mediated devices, or mdevs, to a
portion of a physical GPU. QEMU composes these mdevs into PCI
representations using the existing VFIO user API. This enables
both Intel KVM-GT support, which is also expected to arrive into
Linux mainline during the v4.10 merge window, as well as NVIDIA
vGPU, and also Channel I/O devices (aka CCW devices) for s390
virtualization support. (Kirti Wankhede, Neo Jia)
- Drop unnecessary uses of pcibios_err_to_errno() (Cao Jin)
- Fixes to VFIO capability chain handling (Eric Auger)
- Error handling fixes for fallout from mdev (Christophe JAILLET)
- Notifiers to expose struct kvm to mdev vendor drivers (Jike Song)
- type1 IOMMU model search fixes (Kirti Wankhede, Neo Jia)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)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=gc6j
-----END PGP SIGNATURE-----
Merge tag 'vfio-v4.10-rc1' of git://github.com/awilliam/linux-vfio
Pull VFIO updates from Alex Williamson:
- VFIO updates for v4.10 primarily include a new Mediated Device
interface, which essentially allows software defined devices to be
exposed to users through VFIO. The host vendor driver providing this
virtual device polices, or mediates user access to the device.
These devices often incorporate portions of real devices, for
instance the primary initial users of this interface expose vGPUs
which allow the user to map mediated devices, or mdevs, to a portion
of a physical GPU. QEMU composes these mdevs into PCI representations
using the existing VFIO user API. This enables both Intel KVM-GT
support, which is also expected to arrive into Linux mainline during
the v4.10 merge window, as well as NVIDIA vGPU, and also Channel I/O
devices (aka CCW devices) for s390 virtualization support. (Kirti
Wankhede, Neo Jia)
- Drop unnecessary uses of pcibios_err_to_errno() (Cao Jin)
- Fixes to VFIO capability chain handling (Eric Auger)
- Error handling fixes for fallout from mdev (Christophe JAILLET)
- Notifiers to expose struct kvm to mdev vendor drivers (Jike Song)
- type1 IOMMU model search fixes (Kirti Wankhede, Neo Jia)
* tag 'vfio-v4.10-rc1' of git://github.com/awilliam/linux-vfio: (30 commits)
vfio iommu type1: Fix size argument to vfio_find_dma() in pin_pages/unpin_pages
vfio iommu type1: Fix size argument to vfio_find_dma() during DMA UNMAP.
vfio iommu type1: WARN_ON if notifier block is not unregistered
kvm: set/clear kvm to/from vfio_group when group add/delete
vfio: support notifier chain in vfio_group
vfio: vfio_register_notifier: classify iommu notifier
vfio: Fix handling of error returned by 'vfio_group_get_from_dev()'
vfio: fix vfio_info_cap_add/shift
vfio/pci: Drop unnecessary pcibios_err_to_errno()
MAINTAINERS: Add entry VFIO based Mediated device drivers
docs: Sample driver to demonstrate how to use Mediated device framework.
docs: Sysfs ABI for mediated device framework
docs: Add Documentation for Mediated devices
vfio: Define device_api strings
vfio_platform: Updated to use vfio_set_irqs_validate_and_prepare()
vfio_pci: Updated to use vfio_set_irqs_validate_and_prepare()
vfio: Introduce vfio_set_irqs_validate_and_prepare()
vfio_pci: Update vfio_pci to use vfio_info_add_capability()
vfio: Introduce common function to add capabilities
vfio iommu: Add blocking notifier to notify DMA_UNMAP
...
- Support for the GICv3 ITS on 32bit platforms
- A handful of timer and GIC emulation fixes
- A PMU architecture fix
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=zxXl
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-for-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/ARM updates for 4.10:
- Support for the GICv3 ITS on 32bit platforms
- A handful of timer and GIC emulation fixes
- A PMU architecture fix
When the arch timer code fails to initialize (for example because the
memory mapped timer doesn't work, which is currently seen with the AEM
model), then KVM just continues happily with a final result that KVM
eventually does a NULL pointer dereference of the uninitialized cycle
counter.
Check directly for this in the init path and give the user a reasonable
error in this case.
Cc: Shih-Wei Li <shihwei@cs.columbia.edu>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The GICv2 spec says in section 4.3.12 that a "CPU targets field bit that
corresponds to an unimplemented CPU interface is RAZ/WI."
Currently we allow the guest to write any value in there and it can
read that back.
Mask the written value with the proper CPU mask to be spec compliant.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Sometimes users need to be aware when a vfio_group attaches to a
KVM or detaches from it. KVM already calls get/put method from vfio to
manipulate the vfio_group reference, it can notify vfio_group in
a similar way.
Cc: Kirti Wankhede <kwankhede@nvidia.com>
Cc: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Jike Song <jike.song@intel.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
We should move the ops->destroy(dev) after the list_del(&dev->vm_node)
so that we don't use "dev" after freeing it.
Fixes: a28ebea2ad ("KVM: Protect device ops->create and list_add with kvm->lock")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
- Do not call kvm_notify_acked for PPIs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=1IXI
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-for-4.9-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm
KVM/ARM updates for v4.9-rc7
- Do not call kvm_notify_acked for PPIs
The kvm module has the parameters halt_poll_ns, halt_poll_ns_grow, and
halt_poll_ns_shrink. Halt polling was recently added to the powerpc kvm-hv
module and these parameters were essentially duplicated for that. There is
no benefit to this duplication and it can lead to confusion when trying to
tune halt polling.
Thus move the definition of these variables to kvm_host.h and export them.
This will allow the kvm-hv module to use the same module parameters by
accessing these variables, which will be implemented in the next patch,
meaning that they will no longer be duplicated.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
When we inject a level triggerered interrupt (and unless it
is backed by the physical distributor - timer style), we request
a maintenance interrupt. Part of the processing for that interrupt
is to feed to the rest of KVM (and to the eventfd subsystem) the
information that the interrupt has been EOIed.
But that notification only makes sense for SPIs, and not PPIs
(such as the PMU interrupt). Skip over the notification if
the interrupt is not an SPI.
Cc: stable@vger.kernel.org # 4.7+
Fixes: 140b086dd1 ("KVM: arm/arm64: vgic-new: Add GICv2 world switch backend")
Fixes: 59529f69f5 ("KVM: arm/arm64: vgic-new: Add GICv3 world switch backend")
Reported-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This was reported by syzkaller:
[ INFO: possible recursive locking detected ]
4.9.0-rc4+ #49 Not tainted
---------------------------------------------
kworker/2:1/5658 is trying to acquire lock:
([ 1644.769018] (&work->work)
[< inline >] list_empty include/linux/compiler.h:243
[<ffffffff8128dd60>] flush_work+0x0/0x660 kernel/workqueue.c:1511
but task is already holding lock:
([ 1644.769018] (&work->work)
[<ffffffff812916ab>] process_one_work+0x94b/0x1900 kernel/workqueue.c:2093
stack backtrace:
CPU: 2 PID: 5658 Comm: kworker/2:1 Not tainted 4.9.0-rc4+ #49
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Workqueue: events async_pf_execute
ffff8800676ff630 ffffffff81c2e46b ffffffff8485b930 ffff88006b1fc480
0000000000000000 ffffffff8485b930 ffff8800676ff7e0 ffffffff81339b27
ffff8800676ff7e8 0000000000000046 ffff88006b1fcce8 ffff88006b1fccf0
Call Trace:
...
[<ffffffff8128ddf3>] flush_work+0x93/0x660 kernel/workqueue.c:2846
[<ffffffff812954ea>] __cancel_work_timer+0x17a/0x410 kernel/workqueue.c:2916
[<ffffffff81295797>] cancel_work_sync+0x17/0x20 kernel/workqueue.c:2951
[<ffffffff81073037>] kvm_clear_async_pf_completion_queue+0xd7/0x400 virt/kvm/async_pf.c:126
[< inline >] kvm_free_vcpus arch/x86/kvm/x86.c:7841
[<ffffffff810b728d>] kvm_arch_destroy_vm+0x23d/0x620 arch/x86/kvm/x86.c:7946
[< inline >] kvm_destroy_vm virt/kvm/kvm_main.c:731
[<ffffffff8105914e>] kvm_put_kvm+0x40e/0x790 virt/kvm/kvm_main.c:752
[<ffffffff81072b3d>] async_pf_execute+0x23d/0x4f0 virt/kvm/async_pf.c:111
[<ffffffff8129175c>] process_one_work+0x9fc/0x1900 kernel/workqueue.c:2096
[<ffffffff8129274f>] worker_thread+0xef/0x1480 kernel/workqueue.c:2230
[<ffffffff812a5a94>] kthread+0x244/0x2d0 kernel/kthread.c:209
[<ffffffff831f102a>] ret_from_fork+0x2a/0x40 arch/x86/entry/entry_64.S:433
The reason is that kvm_put_kvm is causing the destruction of the VM, but
the page fault is still on the ->queue list. The ->queue list is owned
by the VCPU, not by the work items, so we cannot just add list_del to
the work item.
Instead, use work->vcpu to note async page faults that have been resolved
and will be processed through the done list. There is no need to flush
those.
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
KVM calls kvm_pmu_set_counter_event_type() when PMCCFILTR is configured.
But this function can't deals with PMCCFILTR correctly because the evtCount
bits of PMCCFILTR, which is reserved 0, conflits with the SW_INCR event
type of other PMXEVTYPER<n> registers. To fix it, when eventsel == 0, this
function shouldn't return immediately; instead it needs to check further
if select_idx is ARMV8_PMU_CYCLE_IDX.
Another issue is that KVM shouldn't copy the eventsel bits of PMCCFILTER
blindly to attr.config. Instead it ought to convert the request to the
"cpu cycle" event type (i.e. 0x11).
To support this patch and to prevent duplicated definitions, a limited
set of ARMv8 perf event types were relocated from perf_event.c to
asm/perf_event.h.
Cc: stable@vger.kernel.org # 4.6+
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Wei Huang <wei@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
1) Since commit:41a54482 changed timer enabled variable to per-vcpu,
the correlative comment in kvm_timer_enable is useless now.
2) After the kvm module init successfully, the timecounter is always
non-null, so we can remove the checking of timercounter.
Signed-off-by: Longpeng(Mike) <longpeng2@huawei.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This patch allows to build and use vGICv3 ITS in 32-bit mode.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Evaluate GITS_BASER_ENTRY_SIZE once as an int data (GITS_BASER<n>'s
Entry Size is 5-bit wide only), so when used as divider no reference
to __aeabi_uldivmod is generated when build for AArch32.
Use unsigned long long for GITS_BASER_PAGE_SIZE_* since they are
used in conjunction with 64-bit data.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
- Kick the vcpu when a pending interrupt becomes pending again
- Prevent access to invalid interrupt registers
- Invalid TLBs when two vcpus from the same VM share a CPU
-----BEGIN PGP SIGNATURE-----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=vj/s
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-for-v4.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/ARM updates for v4.9-rc4
- Kick the vcpu when a pending interrupt becomes pending again
- Prevent access to invalid interrupt registers
- Invalid TLBs when two vcpus from the same VM share a CPU
during the merge window. The rest are fixes for MIPS, s390 and nested VMX.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJYG2H5AAoJEL/70l94x66DK/cH/0jEQ3ynuLAd5CKux7JxI/EP
msSJh1Xqr4+XhXZnuDpGQWrdsBlxoiqA6PsJrUTtyi4nQCDXlT8g+2MDuvqhWIHz
7vw58j/EMJDCVQzYAbN5VDUfk13uB5aSWTo3M9Rf09v0hU1Ql7z8u4CtKEdLpN5Y
LY9bT9fxUmXO7REKP7bdW6ZrDX/hUShYHgMqzXGFMyGBG3ym3a9bggXEzTCD6eNQ
ioogQIWqg+icdhta0iLNAwFClPlcKB2/xo4IUuNgrPwGoHFGJN/8+qxT4+sVbp2B
v8u1zOXlCFXBcskWE+yRRsGe72+mIzz6QScCyO+5HbhKYVfbE9H7KBlFX9rZZ2c=
=IbKx
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"One NULL pointer dereference, and two fixes for regressions introduced
during the merge window.
The rest are fixes for MIPS, s390 and nested VMX"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvm: x86: Check memopp before dereference (CVE-2016-8630)
kvm: nVMX: VMCLEAR an active shadow VMCS after last use
KVM: x86: drop TSC offsetting kvm_x86_ops to fix KVM_GET/SET_CLOCK
KVM: x86: fix wbinvd_dirty_mask use-after-free
kvm/x86: Show WRMSR data is in hex
kvm: nVMX: Fix kernel panics induced by illegal INVEPT/INVVPID types
KVM: document lock orders
KVM: fix OOPS on flush_work
KVM: s390: Fix STHYI buffer alignment for diag224
KVM: MIPS: Precalculate MMIO load resume PC
KVM: MIPS: Make ERET handle ERL before EXL
KVM: MIPS: Fix lazy user ASID regenerate for SMP
In cases like IPI, we could be queueing an interrupt for a VCPU
that is already running and is not about to exit, because the
VCPU has entered the VM with the interrupt pending and would
not trap on EOI'ing that interrupt. This could result to delays
in interrupt deliveries or even loss of interrupts.
To guarantee prompt interrupt injection, here we have to try to
kick the VCPU.
Signed-off-by: Shih-Wei Li <shihwei@cs.columbia.edu>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In our VGIC implementation we limit the number of SPIs to a number
that the userland application told us. Accordingly we limit the
allocation of memory for virtual IRQs to that number.
However in our MMIO dispatcher we didn't check if we ever access an
IRQ beyond that limit, leading to out-of-bound accesses.
Add a test against the number of allocated SPIs in check_region().
Adjust the VGIC_ADDR_TO_INT macro to avoid an actual division, which
is not implemented on ARM(32).
[maz: cleaned-up original patch]
Cc: stable@vger.kernel.org
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Various kvm vm and vcpu stats are provided via debugfs entries.
Currently there is no way to reset these stats back to zero.
Add the ability to clear (reset back to zero) these stats on a per stat
basis by writing to the debugfs files. Only a write value of 0 is accepted.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
The conversion done by commit 3706feacd0 ("KVM: Remove deprecated
create_singlethread_workqueue") is broken. It flushes a single work
item &irqfd->shutdown instead of all of them, and even worse if there
is no irqfd on the list then you get a NULL pointer dereference.
Revert the virt/kvm/eventfd.c part of that patch; to avoid the
deprecated function, just allocate our own workqueue---it does
not even have to be unbound---with alloc_workqueue.
Fixes: 3706feacd0
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
