Currently netcp_module_probe() doesn't check the return value of
of_parse_phandle() that points to the interface data for the
module and then pass the node ptr to the module which is incorrect.
Check for return value and free the intf_modpriv if there is error.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, if netcp_allocate_rx_buf() fails due no descriptors
in the rx free descriptor queue, inside the netcp_rxpool_refill() function
the iterative loop to fill buffers doesn't terminate right away. So modify
the netcp_allocate_rx_buf() to return an error code and use it break the
loop when there is error.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netcp interface is not fully initialized before attach the module
to the interface. For example, the tx pipe/rx pipe is initialized
in ethss module as part of attach(). So until this is complete, the
interface can't be registered. So move registration of interface to
net device outside the current loop that attaches the modules to the
interface.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netcp_core is the first driver that will get initialized and the modules
(ethss, pa etc) will then get initialized. So the code at the end of
netcp_probe() that iterate over the modules is a dead code as the module
list will be always be empty. So remove this code.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On K2HK, sgmii module registers of slave 0 and 1 are mem
mapped to one contiguous block, while those of slave 2
and 3 are mapped to another contiguous block. However,
on K2E and K2L, sgmii module registers of all slaves are
mem mapped to one contiguous block. SGMII APIs expect
slave 0 sgmii base when API is invoked for slave 0 and 1,
and slave 2 sgmii base when invoked for other slaves.
Before this patch, slave 0 sgmii base is always passed to
sgmii API for K2E regardless which slave is the API invoked
for. This patch fixes the problem.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding support for reading mac address using syscon driver for
dra7 and am437x platforms
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moving mac address reading from ethernet driver to common
file for better maintenance and for code reusable.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In DRA72x EVM, by default slave 1 is connected to the onboard
phy, but slave 2 pins are also muxed with video input module
which is controlled by pcf857x gpio and currently to select slave
0 to connect to phy gpio hogging is used, but with
omap2plus_defconfig the pcf857x gpio is built as module. So when
using NFS on DRA72x EVM, board doesn't boot as gpio hogging do
not set proper gpio state to connect slave 0 to phy as it is
built as module and you do not see any errors for not setting
gpio and just mentions dhcp reply not got.
To solve this issue, introducing "mode-gpios" in DT when gpio
based muxing is required. This will throw a warning when gpio
get fails and returns probe defer. When gpio-pcf857x module is
installed, cpsw probes again and ethernet becomes functional.
Verified this on DRA72x with pcf as module and ramdisk.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for 4.3 for MIPS. Here's the summary:
Three fixes that didn't make 4.2-stable:
- a -Os build might compile the kernel using the MIPS16 instruction
set but the R2 optimized inline functions in <uapi/asm/swab.h> are
implemented using 32-bit wide instructions which is invalid.
- a build error in pgtable-bits.h for a particular kernel
configuration.
- accessing registers of the CM GCR might have been compiled to use
64 bit accesses but these registers are onl 32 bit wide.
And also a few new bits:
- move the ATH79 GPIO driver to drivers/gpio
- the definition of IRQCHIP_DECLARE has moved to linux/irqchip.h,
change ATH79 accordingly.
- fix definition of pgprot_writecombine
- add an implementation of dma_map_ops.mmap
- fix alignment of quiet build output for vmlinuz link
- BCM47xx: Use kmemdup rather than duplicating its implementation
- Netlogic: Fix 0x0x prefixes of constants.
- merge Bjorn Helgaas' series to remove most of the weak keywords
from function declarations.
- CP0 and CP1 registers are best considered treated as unsigned
values to avoid large values from becoming negative values.
- improve support for the MIPS GIC timer.
- enable common clock framework for Malta and SEAD3.
- a number of improvments and fixes to dump_tlb().
- document the MIPS TLB dump functionality in Magic SysRq.
- Cavium Octeon CN68XX improvments.
- NetLogic improvments.
- irq: Use access helper irq_data_get_affinity_mask.
- handle MSA unaligned accesses.
- a number of R6-related math-emu fixes.
- support for I6400.
- improvments to MSA support.
- add uprobes support.
- move from deprecated __initcall to arch_initcall.
- remove finish_arch_switch().
- IRQ cleanups by Thomas Gleixner.
- migrate to new 'set-state' interface.
- random small cleanups"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (148 commits)
MIPS: UAPI: Fix unrecognized opcode WSBH/DSBH/DSHD when using MIPS16.
MIPS: Fix alignment of quiet build output for vmlinuz link
MIPS: math-emu: Remove unused handle_dsemul function declaration
MIPS: math-emu: Add support for the MIPS R6 MAX{, A} FPU instruction
MIPS: math-emu: Add support for the MIPS R6 MIN{, A} FPU instruction
MIPS: math-emu: Add support for the MIPS R6 CLASS FPU instruction
MIPS: math-emu: Add support for the MIPS R6 RINT FPU instruction
MIPS: math-emu: Add support for the MIPS R6 MSUBF FPU instruction
MIPS: math-emu: Add support for the MIPS R6 MADDF FPU instruction
MIPS: math-emu: Add support for the MIPS R6 SELNEZ FPU instruction
MIPS: math-emu: Add support for the MIPS R6 SELEQZ FPU instruction
MIPS: math-emu: Add support for the CMP.condn.fmt R6 instruction
MIPS: inst.h: Add new MIPS R6 FPU opcodes
MIPS: Octeon: Fix management port MII address on Kontron S1901
MIPS: BCM47xx: Use kmemdup rather than duplicating its implementation
STAGING: Octeon: Use common helpers for determining interface and port
MIPS: Octeon: Support interfaces 4 and 5
MIPS: Octeon: Set up 1:1 mapping between CN68XX PKO queues and ports
MIPS: Octeon: Initialize CN68XX PKO
STAGING: Octeon: Support CN68XX style WQE
...
Currently CONFIG_ARCH_HAVE_CUSTOM_GPIO_H is defined for all MIPS
machines, and each machine type provides its own gpio.h. However
only a handful really implement the GPIO API, most just forward
everythings to gpiolib.
The Alchemy machine is notable as it provides a system to allow
implementing the GPIO API at the board level. But it is not used by
any board currently supported, so it can also be removed.
For most machine types we can just remove the custom gpio.h, as well
as the custom wrappers if some exists. Some of the code found in
the wrappers must be moved to the respective GPIO driver.
A few more fixes are need in some drivers as they rely on linux/gpio.h
to provides some machine specific definitions, or used asm/gpio.h
instead of linux/gpio.h for the gpio API.
Signed-off-by: Alban Bedel <albeu@free.fr>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Joe Perches <joe@perches.com>
Cc: Daniel Walter <dwalter@google.com>
Cc: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: James Hartley <james.hartley@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Varka Bhadram <varkabhadram@gmail.com>
Cc: Masanari Iida <standby24x7@gmail.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Michael Buesch <m@bues.ch>
Cc: abdoulaye berthe <berthe.ab@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-ide@vger.kernel.org
Cc: linux-gpio@vger.kernel.org
Cc: linux-input@vger.kernel.org
Cc: netdev@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10828/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Propagate error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per Am335x Errata [1] Advisory 1.0.9, The CPSW C0_TX_PEND and
C0_RX_PEND interrupt outputs provide a single transmit interrupt
that combines transmit channel interrupts TXPEND[7:0] and a
single receive interrupt that combines receive channel interrupts
RXPEND[7:0]. The TXPEND[0] and RXPEND[0] interrupt outputs are
connected to the ARM Cortex-A8 interrupt controller (INTC) rather
than the C0_TX_PEND and C0_RX_PEND interrupt outputs. So even
though CPSW interrupt is cleared by writing appropriate values to
EOI register the interrupt is not cleared in IRQ controller. So
interrupt is still pending and CPU is struck in ISR, the
workaround is to disable the interrupts in ARM irq controller.
[1] http://www.ti.com/lit/er/sprz360f/sprz360f.pdf
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/cavium/Kconfig
The cavium conflict was overlapping dependency
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to this patch, rx buffer size for each rx queue
of an interface is configurable through dts bindings.
But for an interface, the first rx queue's rx buffer
size is always the usual MTU size (plus usual overhead)
and page size for the remaining rx queues (if they are
enabled by specifying a non-zero rx queue depth dts
binding of the corresponding interface). This patch
removes the rx buffer size configuration capability.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of processing tx events in isr adding separate napi for
tx which improves performance by ~180Mbps with
omap2plus_defconfig on DRA74x platform. Also cleaning up rx napis
by renaming to napi_rx for better understanding the code.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since interrupt is shared between the two ethernet interface and
in isr only one napi is scheduled at an instance so having two
napis doesn't make any difference. So making napi also as a
common resource for the dual ethernet interfaces.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CPSW interrupts can be disabled by masking CPSW interrupts and
clearing interrupt by writing appropriate EOI. So removing all
disable_irq/enable_irq as discussed in [1]
[1] http://patchwork.ozlabs.org/patch/492741/
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/s390/net/bpf_jit_comp.c
drivers/net/ethernet/ti/netcp_ethss.c
net/bridge/br_multicast.c
net/ipv4/ip_fragment.c
All four conflicts were cases of simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch clean up error handle code to use goto label properly. In some
cases, the code unnecessarily use goto instead of just returning the error
code. Code also make explicit calls to devm_* APIs on error which is
not necessary. In the gbe_remove() also it makes similar calls which is
also unnecessary.
Also fix few checkpatch warnings
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code seems to assume a null is returned when the list is empty
from first_sec_slave() to break the loop which is incorrect. Fix the
code by using list_empty().
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently if user do rmmod keystone_netcp.ko following warning is
seen :-
[ 59.035891] ------------[ cut here ]------------
[ 59.040535] WARNING: CPU: 2 PID: 1619 at drivers/net/ethernet/ti/
netcp_core.c:2127 netcp_remove)
This is because the interface list is not cleaned up in netcp_remove.
This patch fixes this. Also fix some checkpatch related warnings.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some of the K2E and K2L platforms, the two DWORDs in
efuse occupied by the pre-programmed mac address for
slave port 1 are swapped. To workaround this issue,
this patch adds a new define NETCP_EFUSE_ADDR_SWAP (2)
which signifies the occurrence of such swapping so that
the driver can take proper action. The flag can be
enabled in the corresponding netcp interface dts binding
as efuse-mac = <2> under the corresponding netcp
interface node.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch asserts SGMII RTRESET, i.e. resetting the SGMII Tx/Rx
logic, during network interface shutdown to avoid having the
hardware wedge when shutting down with high incoming traffic rates.
This is cleared (brought out of RTRESET) when the interface is
brought back up.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the missing statistics for the host
and slave ports of the CPSW on K2L and K2E platforms.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In certain applications it's beneficial to allow the CPSW h/w
stats counters to continue to increment even while the kernel
polls them. This patch implements this behavior for both 1G
and 10G ethernet subsystem modules.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Different Keystone2 platforms have different number and
layouts of hw statistics modules. This patch consolidates
the statistics processing of different Keystone2 platforms
for easy maintenance.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CPSW driver keeps internally some, but not all, of
the statistics available in the hw statistics modules. Furthermore,
some of the locations in the hw statistics modules are reserved and
contain no useful information. Prior to this patch, the driver
allocates memory of the size of the the whole hw statistics modules,
instead of the size of statistics-entries-interested-in (i.e. et_stats),
for internal storage. This patch fixes that.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes error in the setting of the hw statistics
module base for K2HK platform. In K2HK although there are
4 hw statistics modules, but only 2 are visible at a time.
Thus when setting up the pointers to the base of the
corresponding hw statistics modules, modules 0 and 2 should
point to one base, while modules 1 and 3 should point to the
other.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a bug in which the timer routine synchronized
against the ethtool-triggered statistics updates with spin_lock_bh().
A timer function is itself a bottom-half, so this should be
spin_lock().
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/bridge/br_mdb.c
br_mdb.c conflict was a function call being removed to fix a bug in
'net' but whose signature was changed in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
With commit c03abd8463 ("net: ethernet: cpsw: don't requests IRQs
we don't use") common isr and napi are separated into separate tx isr
and rx isr/napi, but still in rx napi tx events are handled. So removing
the tx event handling in rx napi.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The keystone qmss will raise interrupt when packet arrive at the
receive queue. Only control available to avoid interrupt from happening
is to keep the free descriptor queue (FDQ) empty in the receive side.
So the filling of descriptors into the FDQ has to happen after
request_irq() call is made as part of knav_queue_enable_notify(). So
move the function netcp_rxpool_refill() after this call.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/bridge/br_mdb.c
Minor conflict in br_mdb.c, in 'net' we added a memset of the
on-stack 'ip' variable whereas in 'net-next' we assign a new
member 'vid'.
Signed-off-by: David S. Miller <davem@davemloft.net>
platform_driver does not need to set an owner because
platform_driver_register() will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 'c03abd84634d ("net: ethernet: cpsw: don't requests
IRQs we don't use")', common isr is split into tx and rx, but
in rx isr tx interrupt is also disabledi in cpsw_disable_irq().
So tx interrupts are not handled during rx interrupts and rx
napi completion and results in poor tx performance by 40Mbps.
Fixing by disabling only rx interrupt in rx isr.
Cc: Felipe Balbi <balbi@ti.com>
Cc: <stable@vger.kernel.org> # v4.0+
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This howto made sense in the 1990s when users had to manually configure
ISA cards with jumpers or vendor utilities, but with the implementation
of PCI it became increasingly less and less relevant, to the point where
it has been well over a decade since I last updated it. And there is
no value in anyone else taking over updating it either.
However the references to it continue to spread as boiler plate text
from one Kconfig file into the next. We are not doing end users any
favours by pointing them at this old document, so lets kill it with
fire, once and for all, to hopefully stop any further spread.
No code is changed in this commit, just Kconfig help text.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function, cpsw_intr_disable, already calls cpdma_ctlr_int_ctrl. There
is no need to disable the dma interrupts twice. This patch removes the
extra calls.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function, cpsw_intr_enable, already calls cpdma_ctlr_int_ctrl. There
is no need to enable the dma interrupts twice. This patch removes the
extra call.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The funtions, cpsw_ale_flush and cpsw_ale_set_ageout, have never been used
since they were first introduced. This patch removes the dead code.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Having the breaks too far to the left makes parsing the dense switch/case
block unnecessarily harder.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
None of those drivers uses last_rx for its own needs.
See 4dc89133f4 ("net: add a comment on
netdev->last_rx") for reference.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Zhangfei Gao <zhangfei.gao@linaro.org>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Wingman Kwok <w-kwok2@ti.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when interface type is MAC to Phy, netif_carrier_(on/off)
is called which is not needed as Phy lib already updates the carrier
status to net stack. This is needed only for other interface types
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the driver to use ns_to_timespec64() and
timespec64_to_ns() instead of open coding the same logic.
Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver's clock is implemented using a timecounter, and so with
this patch the driver is ready for the year 2038.
Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NetCP 1.5 available on newer K2 SoCs such as K2E and K2L introduced 3
variants of the ethss subsystem, 9 port, 5 port and 2 port. These have
one host port towards the CPU and N external slave ports.
To customize the driver for these new ethss sub systems, multiple
compatibility strings are introduced. Currently some of parameters that
are different on different variants such as number of ALE ports, stats
modules and number of ports are defined through constants. These are now
changed to variables in gbe_priv data that get set based on the
compatibility string. This is required as there are no hardware
identification registers available to distinguish among the variants
of NetCP 1.5 ethss. However there is identification register available
to differentiate between NetCP 1.4 vs NetCP 1.5 and the same is made use
of in the code to differentiate them.
For more reading on the details of this peripheral, please refer to the
User Guide available at http://www.ti.com/lit/pdf/spruhz3
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Mugunthan V N <mugunthanvnm@ti.com>
CC: "Lad, Prabhakar" <prabhakar.csengg@gmail.com>
CC: Grygorii Strashko <grygorii.strashko@ti.com>
CC: Christoph Jaeger <cj@linux.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Markus Pargmann <mpa@pengutronix.de>
CC: Kumar Gala <galak@codeaurora.org>
CC: Ian Campbell <ijc+devicetree@hellion.org.uk>
CC: Mark Rutland <mark.rutland@arm.com>
CC: Pawel Moll <pawel.moll@arm.com>
CC: Rob Herring <robh+dt@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix following checkpatch error. It seems to have passed checkpatch
last time when original code was introduced.
ERROR: Macros with complex values should be enclosed in parentheses
#172: FILE: drivers/net/ethernet/ti/netcp_ethss.c:869:
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Mugunthan V N <mugunthanvnm@ti.com>
CC: "Lad, Prabhakar" <prabhakar.csengg@gmail.com>
CC: Grygorii Strashko <grygorii.strashko@ti.com>
CC: Christoph Jaeger <cj@linux.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Markus Pargmann <mpa@pengutronix.de>
CC: Kumar Gala <galak@codeaurora.org>
CC: Ian Campbell <ijc+devicetree@hellion.org.uk>
CC: Mark Rutland <mark.rutland@arm.com>
CC: Pawel Moll <pawel.moll@arm.com>
CC: Rob Herring <robh+dt@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keystone netcp driver re-uses davinci mdio driver. So enable it
by default for keystone netcp driver.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Mugunthan V N <mugunthanvnm@ti.com>
CC: "Lad, Prabhakar" <prabhakar.csengg@gmail.com>
CC: Grygorii Strashko <grygorii.strashko@ti.com>
CC: Christoph Jaeger <cj@linux.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Markus Pargmann <mpa@pengutronix.de>
CC: Kumar Gala <galak@codeaurora.org>
CC: Ian Campbell <ijc+devicetree@hellion.org.uk>
CC: Mark Rutland <mark.rutland@arm.com>
CC: Pawel Moll <pawel.moll@arm.com>
CC: Rob Herring <robh+dt@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethss has multiple modules within the sub system
- switch sub system
- sgmii
- mdio
- switch module
NetCP driver re-uses existing davinci mdio driver. It requires to
have its own register region to map the reg space. So restructure
the code to use separate reg region for the individual modules it
manages. Use range property to define register space of NetCP and
use reg property to define individual reg spaces. So MDIO will have
its own reg space to map. This is a pre-requisite to enable MDIO
driver for NetCP.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Mugunthan V N <mugunthanvnm@ti.com>
CC: "Lad, Prabhakar" <prabhakar.csengg@gmail.com>
CC: Grygorii Strashko <grygorii.strashko@ti.com>
CC: Christoph Jaeger <cj@linux.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Markus Pargmann <mpa@pengutronix.de>
CC: Kumar Gala <galak@codeaurora.org>
CC: Ian Campbell <ijc+devicetree@hellion.org.uk>
CC: Mark Rutland <mark.rutland@arm.com>
CC: Pawel Moll <pawel.moll@arm.com>
CC: Rob Herring <robh+dt@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
10G switch requires forward port number in the taginfo field,
where as it should be in packet_info field for necp 1.4 Ethss. So
fill this value correctly in the knav dma descriptor.
Also rename dma_psflags field in struct netcp_tx_pipe to switch_to_port
as it contain no flag, but the switch port number for forwarding the
packet. Add a flag to hold the new flag, SWITCH_TO_PORT_IN_TAGINFO which
will be set for 10G. This can also used in the future for other flags for
the tx_pipe.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Mugunthan V N <mugunthanvnm@ti.com>
CC: "Lad, Prabhakar" <prabhakar.csengg@gmail.com>
CC: Grygorii Strashko <grygorii.strashko@ti.com>
CC: Christoph Jaeger <cj@linux.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Markus Pargmann <mpa@pengutronix.de>
CC: Kumar Gala <galak@codeaurora.org>
CC: Ian Campbell <ijc+devicetree@hellion.org.uk>
CC: Mark Rutland <mark.rutland@arm.com>
CC: Pawel Moll <pawel.moll@arm.com>
CC: Rob Herring <robh+dt@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
To test a checkpatch spelling patch, I ran codespell against
drivers/net/ethernet/.
$ git ls-files drivers/net/ethernet/ | \
while read file ; do \
codespell -w $file; \
done
I removed a false positive in e1000_hw.h
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/rocker/rocker.c
The rocker commit was two overlapping changes, one to rename
the ->vport member to ->pport, and another making the bitmask
expression use '1ULL' instead of plain '1'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) If an IPVS tunnel is created with a mixed-family destination
address, it cannot be removed. Fix from Alexey Andriyanov.
2) Fix module refcount underflow in netfilter's nft_compat, from Pablo
Neira Ayuso.
3) Generic statistics infrastructure can reference variables sitting on
a released function stack, therefore use dynamic allocation always.
Fix from Ignacy Gawędzki.
4) skb_copy_bits() return value test is inverted in ip_check_defrag().
5) Fix network namespace exit in openvswitch, we have to release all of
the per-net vports. From Pravin B Shelar.
6) Fix signedness bug in CAIF's cfpkt_iterate(), from Dan Carpenter.
7) Fix rhashtable grow/shrink behavior, only expand during inserts and
shrink during deletes. From Daniel Borkmann.
8) Netdevice names with semicolons should never be allowed, because
they serve as a separator. From Matthew Thode.
9) Use {,__}set_current_state() where appropriate, from Fabian
Frederick.
10) Revert byte queue limits support in r8169 driver, it's causing
regressions we can't figure out.
11) tcp_should_expand_sndbuf() erroneously uses tp->packets_out to
measure packets in flight, properly use tcp_packets_in_flight()
instead. From Neal Cardwell.
12) Fix accidental removal of support for bluetooth in CSR based Intel
wireless cards. From Marcel Holtmann.
13) We accidently added a behavioral change between native and compat
tasks, wrt testing the MSG_CMSG_COMPAT bit. Just ignore it if the
user happened to set it in a native binary as that was always the
behavior we had. From Catalin Marinas.
14) Check genlmsg_unicast() return valud in hwsim netlink tx frame
handling, from Bob Copeland.
15) Fix stale ->radar_required setting in mac80211 that can prevent
starting new scans, from Eliad Peller.
16) Fix memory leak in nl80211 monitor, from Johannes Berg.
17) Fix race in TX index handling in xen-netback, from David Vrabel.
18) Don't enable interrupts in amx-xgbe driver until all software et al.
state is ready for the interrupt handler to run. From Thomas
Lendacky.
19) Add missing netlink_ns_capable() checks to rtnl_newlink(), from Eric
W Biederman.
20) The amount of header space needed in macvtap was not calculated
properly, fix it otherwise we splat past the beginning of the
packet. From Eric Dumazet.
21) Fix bcmgenet TCP TX perf regression, from Jaedon Shin.
22) Don't raw initialize or mod timers, use setup_timer() and
mod_timer() instead. From Vaishali Thakkar.
23) Fix software maintained statistics in bcmgenet and systemport
drivers, from Florian Fainelli.
24) DMA descriptor updates in sh_eth need proper memory barriers, from
Ben Hutchings.
25) Don't do UDP Fragmentation Offload on RAW sockets, from Michal
Kubecek.
26) Openvswitch's non-masked set actions aren't constructed properly
into netlink messages, fix from Joe Stringer.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (116 commits)
openvswitch: Fix serialization of non-masked set actions.
gianfar: Reduce logging noise seen due to phy polling if link is down
ibmveth: Add function to enable live MAC address changes
net: bridge: add compile-time assert for cb struct size
udp: only allow UFO for packets from SOCK_DGRAM sockets
sh_eth: Really fix padding of short frames on TX
Revert "sh_eth: Enable Rx descriptor word 0 shift for r8a7790"
sh_eth: Fix RX recovery on R-Car in case of RX ring underrun
sh_eth: Ensure proper ordering of descriptor active bit write/read
net/mlx4_en: Disbale GRO for incoming loopback/selftest packets
net/mlx4_core: Fix wrong mask and error flow for the update-qp command
net: systemport: fix software maintained statistics
net: bcmgenet: fix software maintained statistics
rxrpc: don't multiply with HZ twice
rxrpc: terminate retrans loop when sending of skb fails
net/hsr: Fix NULL pointer dereference and refcnt bugs when deleting a HSR interface.
net: pasemi: Use setup_timer and mod_timer
net: stmmac: Use setup_timer and mod_timer
net: 8390: axnet_cs: Use setup_timer and mod_timer
net: 8390: pcnet_cs: Use setup_timer and mod_timer
...
Use the built-in function instead of memset.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting a dev_pm_ops suspend/resume pair but not a set of
hibernation functions means those pm functions will not be
called upon hibernation.
Fix this by using SIMPLE_DEV_PM_OPS, which appropriately
assigns the suspend and hibernation handlers and move
cpsw_suspend/resume calbacks under CONFIG_PM_SLEEP
to avoid build warnings.
Signed-off-by: Grygorii Strashko <Grygorii.Strashko@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting a dev_pm_ops suspend_late/resume_early pair but not a
set of hibernation functions means those pm functions will
not be called upon hibernation.
Fix this by using SET_LATE_SYSTEM_SLEEP_PM_OPS, which appropriately
assigns the suspend and hibernation handlers and move
davinci_mdio_x callbacks under CONFIG_PM_SLEEP to avoid build warnings.
Signed-off-by: Grygorii Strashko <Grygorii.Strashko@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to this patch, sending a packet with the source MAC address of one
of the CPSW interfaces to one of the CPSW slave ports while it's configured in
dual_emac mode would update the port_num field of the VLAN/Unicast Address
Table Entry. This would cause it to discard all incoming traffic addressed to
that MAC address, essentially rendering the port useless until the ALE table is
cleared (by starting and stopping the interface or rebooting.)
For example, if eth0 has a MAC address of 90:59:af:8f:43:e9 it will have
an ALE table entry:
00 00 00 00 59 90 02 30 e9 43 8f af
(VLAN Addr vlan_id=2 unicast type=0 port_num=0 addr=90:59:af:8f:43:e9)
If you configure another device with the same MAC address and connect it
to the first CPSW slave port and send some traffic the ALE table entry
becomes:
04 00 00 00 59 90 02 30 e9 43 8f af
(VLAN Addr vlan_id=2 unicast type=0 port_num=1 addr=90:59:af:8f:43:e9)
>From this point forward all incoming traffic addressed to
90:59:af:8f:43:e9 will be dropped.
Setting the SECURE bit for the VLAN/Unicast address table entry for each
interface's MAC address corrects the problem.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull kconfig updates from Michal Marek:
"Yann E Morin was supposed to take over kconfig maintainership, but
this hasn't happened. So I'm sending a few kconfig patches that I
collected:
- Fix for missing va_end in kconfig
- merge_config.sh displays used if given too few arguments
- s/boolean/bool/ in Kconfig files for consistency, with the plan to
only support bool in the future"
* 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kconfig: use va_end to match corresponding va_start
merge_config.sh: Display usage if given too few arguments
kconfig: use bool instead of boolean for type definition attributes
this patch fixes following sparse warning:
cpsw-common.c:23:5: warning: symbol 'cpsw_am33xx_cm_get_macid' was not declared. Should it be static?
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The functions cpsw_ale_destroy() and of_dev_put() test whether their argument
is NULL and then return immediately. Thus the test around the call
is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is only an API consolidation and should make things more readable
it replaces var * HZ / 1000 by msecs_to_jiffies(var).
As there is a discrepancy between the code and the comments this is in
a separate patch.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is only an API consolidation and should make things more readable
it replaces var * HZ / 1000 by msecs_to_jiffies(var).
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
NetCP on Keystone has cpsw ale function similar to other TI SoCs
and this driver is re-used. To allow both ti cpsw and keystone netcp
to re-use the driver, convert the cpsw ale to a module and configure
it through Kconfig option CONFIG_TI_CPSW_ALE. Currently it is statically
linked to both TI CPSW and NetCP and this causes issues when the above
drivers are built as dynamic modules. This patch addresses this issue
While at it, fix the Makefile and code to build both netcp_core and
netcp_ethss as dynamic modules. This is needed to support arm allmodconfig.
This also requires exporting of API calls provided by netcp_core so that
both the above can be dynamic modules.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Looks like on 3517 davinci_emac MAC address registers have a
different layout compared to dm816x and am33xx.
Let's add a function to get the 3517 MAC address.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At least on dm81xx, we can get the davinci_emac MAC address the same
way as on am33xx cpsw.
Let's also use ether_addr_copy() for davinci_emac while at it.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Looks like davinci_emac and cpsw can share some code although the
device registers have a different layout.
At least the code for getting the MAC address using syscon can
be shared by passing the register offset. Let's start with that
and set up a minimal shared cpsw-shared.c.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently CPTS is built into the netcp driver even though there is no
call out to the CPTS driver. This patch removes the dependency in Kconfig
and remove cpts.o from the Makefile for NetCP.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/arm/boot/dts/imx6sx-sdb.dts
net/sched/cls_bpf.c
Two simple sets of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
In Dual EMAC, the default VLANs are used to segregate Rx packets between
the ports, so adding the same default VLAN to the switch will affect the
normal packet transfers. So returning error on addition of dual EMAC
default VLANs.
Even if EMAC 0 default port VLAN is added to EMAC 1, it will lead to
break dual EMAC port separations.
Fixes: d9ba8f9e62 (driver: net: ethernet: cpsw: dual emac interface implementation)
Cc: <stable@vger.kernel.org> # v3.9+
Reported-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enhances the NetCP gbe driver to support 10GbE subsystem
available in Keystone NetCP. The 3-port 10GbE switch sub-module contains
the following components:- 10GbE Switch, MDIO Module, 2 PCS-R Modules
(10GBase-R) and 2 SGMII modules (10/100/1000Base-T). The GBE driver
together with netcp core driver provides support for 10G Ethernet
on Keystone SoCs.
10GbE hardware spec is available at
http://www.ti.com/general/docs/lit/getliterature.tsp?baseLiteratureNumber=spruhj5&fileType=pdf
Cc: David Miller <davem@davemloft.net>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Santosh Shilimkar <santosh.shilimkar@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Wingman Kwok <w-kwok2@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add support for 1G Ethernet driver based on Keystone
NetCP hardware. The gigabit Ethernet (GbE) switch subsystem is one of the main
components of the network coprocessor (NETCP) peripheral. The purpose of the
gigabit Ethernet switch subsystem in the NETCP is to provide an interface to
transfer data between the host device and another connected device in
compliance with the Ethernet protocol. GbE consists of 5 port Ethernet Switch
module, 4 Serial Gigabit Media Independent Interface (SGMII) modules, MDIO
module and SerDes.
Driver for 5 port GbE switch and SGMII module is added in this patch. These
hardware modules along with netcp core driver provides Network driver functions
for 1G Ethernet.
Detailed hardware spec is available at
http://www.ti.com/lit/ug/sprugv9d/sprugv9d.pdf
Cc: David Miller <davem@davemloft.net>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Santosh Shilimkar <santosh.shilimkar@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Wingman Kwok <w-kwok2@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The network coprocessor (NetCP) is a hardware accelerator available in
Keystone SoCs that processes Ethernet packets. NetCP consists of following
hardware components
1 Gigabit Ethernet (GbE) subsystem with a Ethernet switch sub-module to
send and receive packets.
2 Packet Accelerator (PA) module to perform packet classification
operations such as header matching, and packet modification operations
such as checksum generation.
3 Security Accelerator(SA) capable of performing IPSec operations on
ingress/egress packets.
4 An optional 10 Gigabit Ethernet Subsystem (XGbE) which includes a
3-port Ethernet switch sub-module capable of 10Gb/s and 1Gb/s rates
per Ethernet port.
5 Packet DMA and Queue Management Subsystem (QMSS) to enqueue and dequeue
packets and DMA the packets between memory and NetCP hardware components
described above.
NetCP core driver make use of the Keystone Navigator driver API to allocate
DMA channel for the Ethenet device and to handle packet queue/de-queue,
Please refer API's in include/linux/soc/ti/knav_dma.h and
drivers/soc/ti/knav_qmss.h for details.
NetCP driver consists of NetCP core driver and at a minimum Gigabit
Ethernet (GBE) module (1) driver to implement the Network device function.
Other modules (2,3) can be optionally added to achieve supported hardware
acceleration function. The initial version of the driver include NetCP
core driver and GBE driver modules.
Please refer Documentation/devicetree/bindings/net/keystone-netcp.txt
for design of the driver.
Cc: David Miller <davem@davemloft.net>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Santosh Shilimkar <santosh.shilimkar@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Wingman Kwok <w-kwok2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c03abd8463 (net: ethernet: cpsw: don't requests IRQs we don't
use) left one build breakage when NET_POLL_CONTROLLER is enabled.
Fix this build break by referring to the correct irqs_table array.
Fixes: c03abd8463 (net: ethernet: cpsw: don't requests IRQs we don't use)
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CPSW never uses RX_THRESHOLD or MISC interrupts. In
fact, they are always kept masked in their appropriate
IRQ Enable register.
Instead of allocating an IRQ that never fires, it's best
to remove that code altogether and let future patches
implement it if anybody needs those.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is in preparation for a nicer IRQ
handling scheme where we use different IRQ
handlers for each IRQ line (as it should be).
Later, we will also drop IRQs offset 0 and 3
because they are always disabled in this driver.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On dm816x we have two emac controllers with separate memory
areas.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some devices like dm816x have the MDIO registers within the first EMAC
instance address space. Let's fix the issue by allowing to pass an
optional second IO range for the EMAC control register area.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Looks like the phy_id is never set up beyond getting the phandle.
Note that we can remove the ifdef for phy_node as there is a stub
for of_phy_connec() if CONFIG_OF is not set.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We only use clk_get() to get the frequency, the rest is done by
the runtime PM calls. Let's free the clock too.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 3ba9738134 ("net: ethernet: davinci_emac: add pm_runtime support")
added support for runtime PM, but it causes issues on omap3 related devices
that actually gate the clocks:
Unhandled fault: external abort on non-linefetch (0x1008)
...
[<c04160f0>] (emac_dev_getnetstats) from [<c04d6a3c>] (dev_get_stats+0x78/0xc8)
[<c04d6a3c>] (dev_get_stats) from [<c04e9ccc>] (rtnl_fill_ifinfo+0x3b8/0x938)
[<c04e9ccc>] (rtnl_fill_ifinfo) from [<c04eade4>] (rtmsg_ifinfo+0x68/0xd8)
[<c04eade4>] (rtmsg_ifinfo) from [<c04dd35c>] (register_netdevice+0x3a0/0x4ec)
[<c04dd35c>] (register_netdevice) from [<c04dd4bc>] (register_netdev+0x14/0x24)
[<c04dd4bc>] (register_netdev) from [<c041755c>] (davinci_emac_probe+0x408/0x5c8)
[<c041755c>] (davinci_emac_probe) from [<c0396d78>] (platform_drv_probe+0x48/0xa4)
Let's fix it by moving the pm_runtime_get() call earlier, and also add it to
the emac_dev_getnetstats(). Also note that we want to use pm_runtime_get_sync()
as we don't want to have deferred_resume happen. And let's also check the
return value for pm_runtime_get_sync() as noted by Felipe Balbi <balbi@ti.com>.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Acked-by: Mark A. Greer <mgreer@animalcreek.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On davinci_emac, we have pulse interrupts. This means that we need to
clear the EOI bits when disabling interrupts as otherwise the interrupts
keep happening. And we also need to not clear the EOI bits again when
enabling the interrupts as otherwise we will get tons of:
unexpected IRQ trap at vector 00
These errors almost certainly mean that the omap-intc.c is signaling
a spurious interrupt with the reserved irq 127 as we've seen earlier
on omap3.
Let's fix the issue by clearing the EOI bits when disabling the
interrupts. Let's also keep the comment for "Rx Threshold and Misc
interrupts are not enabled" for both enable and disable so people
are aware of this when potentially adding more support.
Note that eventually we should handle the RX and TX interrupts
separately like cpsw is now doing. However, so far I have not seen
any issues with this based on my testing, so it seems to behave a
little different compared to the cpsw that had a similar issue.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
while adding vlan in dual EMAC mode, only specific ports should be
subscribed for the vlan, else it will lead to switching mode and
if both ports connected to same switch cpsw will hung as it creates
a network loop. Fixing this by adding only specific ports in case
of dual EMAC.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/xen-netfront.c
Minor overlapping changes in xen-netfront.c, mostly to do
with some buffer management changes alongside the split
of stats into TX and RX.
Signed-off-by: David S. Miller <davem@davemloft.net>
Since ALE table is a common resource for both the interfaces in Dual EMAC
mode and while bringing up the second interface in cpsw_ndo_set_rx_mode()
all the multicast entries added by the first interface is flushed out and
only second interface multicast addresses are added. Fixing this by
flushing multicast addresses based on dual EMAC port vlans which will not
affect the other emac port multicast addresses.
Fixes: d9ba8f9 (driver: net: ethernet: cpsw: dual emac interface implementation)
Cc: <stable@vger.kernel.org> # v3.9+
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for keyword 'boolean' will be dropped later on.
No functional change.
Reference: http://lkml.kernel.org/r/cover.1418003065.git.cj@linux.com
Signed-off-by: Christoph Jaeger <cj@linux.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
The CPSW IP implements pulse-signaled interrupts. Due to
that we must write a correct, pre-defined value to the
CPDMA_MACEOIVECTOR register so the controller generates
a pulse on the correct IRQ line to signal the End Of
Interrupt.
The way the driver is written today, all four IRQ lines
are requested using the same IRQ handler and, because of
that, we could fall into situations where a TX IRQ fires
but we tell the controller that we ended an RX IRQ (or
vice-versa). This situation triggers an IRQ storm on the
reserved IRQ 127 of INTC which will in turn call ack_bad_irq()
which will, then, print a ton of:
unexpected IRQ trap at vector 00
In order to fix the problem, we are moving all calls to
cpdma_ctlr_eoi() inside the IRQ handler and making sure
we *always* write the correct value to the CPDMA_MACEOIVECTOR
register. Note that the algorithm assumes that IRQ numbers and
value-to-be-written-to-EOI are proportional, meaning that a
write of value 0 would trigger an EOI pulse for the RX_THRESHOLD
Interrupt and that's the IRQ number sitting in the 0-th index
of our irqs_table array.
This, however, is safe at least for current implementations of
CPSW so we will refrain from making the check smarter (and, as
a side-effect, slower) until we actually have a platform where
IRQ lines are swapped.
This patch has been tested for several days with AM335x- and
AM437x-based platforms. AM57x was left out because there are
still pending patches to enable ethernet in mainline for that
platform. A read of the TRM confirms the statement on previous
paragraph.
Reported-by: Yegor Yefremov <yegorslists@googlemail.com>
Fixes: 510a1e7 (drivers: net: davinci_cpdma: acknowledge interrupt properly)
Cc: <stable@vger.kernel.org> # v3.9+
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the driver to use the new and improved method
for adjusting the offset of a timecounter.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The timecounter code has almost nothing to do with the clocksource
code. Let it live in its own file. This will help isolate the
timecounter users from the clocksource users in the source tree.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CPSW is present in AM33xx, AM43xx, DRA7xx.
Updating the Kconfig to depend on ARCH_OMAP2PLUS instead of listing
all SoC's.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TX_IN_SEL offset for the CPSW_PORT/TX_IN_CTL register was
incorrect. This caused the Dual MAC mode to never get set when
it should. It also caused possible unintentional setting of a
bit in the CPSW_PORT/TX_BLKS_REM register.
The purpose of setting the Dual MAC mode for this register is to:
"... allow packets from both ethernet ports to be written into
the FIFO without one port starving the other port."
- AM335x ARM TRM
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit ae5c6c6d "ptp: Classify ptp over ip over vlan packets" changed the
code in two drivers that matches time stamps with PTP frames, with the goal
of allowing VLAN tagged PTP packets to receive hardware time stamps.
However, that commit failed to account for the VLAN header when parsing
IPv4 packets. This patch fixes those two drivers to correctly match VLAN
tagged IPv4/UDP PTP messages with their time stamps.
This patch should also be applied to v3.17.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when cpsw is build as modulea and simple insert and removal of module
creates a deadlock, due to delete timer. the timer is created and destroyed
in cpsw_ale_start and cpsw_ale_stop which are from device open and close.
root@am437x-evm:~# modprobe -r ti_cpsw
[ 158.505333] INFO: trying to register non-static key.
[ 158.510623] the code is fine but needs lockdep annotation.
[ 158.516448] turning off the locking correctness validator.
[ 158.522282] CPU: 0 PID: 1339 Comm: modprobe Not tainted 3.14.23-00445-gd41c88f #44
[ 158.530359] [<c0015380>] (unwind_backtrace) from [<c0012088>] (show_stack+0x10/0x14)
[ 158.538603] [<c0012088>] (show_stack) from [<c054ad70>] (dump_stack+0x78/0x94)
[ 158.546295] [<c054ad70>] (dump_stack) from [<c0088008>] (__lock_acquire+0x176c/0x1b74)
[ 158.554711] [<c0088008>] (__lock_acquire) from [<c0088944>] (lock_acquire+0x9c/0x104)
[ 158.563043] [<c0088944>] (lock_acquire) from [<c004e520>] (del_timer_sync+0x44/0xd8)
[ 158.571289] [<c004e520>] (del_timer_sync) from [<bf2eac1c>] (cpsw_ale_destroy+0x10/0x3c [ti_cpsw])
[ 158.580821] [<bf2eac1c>] (cpsw_ale_destroy [ti_cpsw]) from [<bf2eb268>] (cpsw_remove+0x30/0xa0 [ti_cpsw])
[ 158.591000] [<bf2eb268>] (cpsw_remove [ti_cpsw]) from [<c035ef44>] (platform_drv_remove+0x18/0x1c)
[ 158.600527] [<c035ef44>] (platform_drv_remove) from [<c035d8bc>] (__device_release_driver+0x70/0xc8)
[ 158.610236] [<c035d8bc>] (__device_release_driver) from [<c035e0d4>] (driver_detach+0xb4/0xb8)
[ 158.619386] [<c035e0d4>] (driver_detach) from [<c035d6e4>] (bus_remove_driver+0x4c/0x90)
[ 158.627988] [<c035d6e4>] (bus_remove_driver) from [<c00af2a8>] (SyS_delete_module+0x10c/0x198)
[ 158.637144] [<c00af2a8>] (SyS_delete_module) from [<c000e580>] (ret_fast_syscall+0x0/0x48)
[ 179.524727] INFO: rcu_sched detected stalls on CPUs/tasks: {} (detected by 0, t=2102 jiffies, g=1487, c=1486, q=6)
[ 179.535741] INFO: Stall ended before state dump start
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cpsw driver did not support the IFF_ALLMULTI flag which makes dynamic
multicast routing not work. Related to this, when enabling IFF_PROMISC
in switch mode, all registered multicast addresses are flushed, resulting
in only broadcast and unicast traffic being received.
A new cpsw_ale_set_allmulti function now scans through the ALE entry
table and adds/removes the host port from the unregistered multicast
port mask of each vlan entry depending on the state of IFF_ALLMULTI.
In promiscious mode, cpsw_ale_set_allmulti is used to force reception
of all multicast traffic in addition to the unicast and broadcast traffic.
With this change dynamic multicast and promiscious mode both work in
switch mode.
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
0d961b3b52 (drivers: net: cpsw: fix buggy
loop condition) accidentally fixed a loop comparison in too many places
while fixing a real bug.
It was correct to fix the dual_emac mode section since there 'i' is used
as an index into priv->slaves which is a 0 based array.
However the other two changes (which are only used in switch mode)
are wrong since there 'i' is actually the ALE port number, and port 0
is the host port, while port 1 and up are the slave ports.
Putting the loop condition back in the switch mode section fixes it.
A comment has been added to point out the intent clearly to avoid future
confusion. Also a comment is fixed that said the opposite of what was
actually happening.
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
when slave 0 has no phy and slave 1 connected to phy, driver probe will
fail as there is no phy id present for slave 0 device tree, so continuing
even though no phy-id found, also moving mac-id read later to ensure
mac-id is read from device tree even when phy-id entry in not found.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
remove all the child devices from the system to make sure that re-insert of
cpsw module doesn't fail on child device populated by of_platform_populate().
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
