There exists an intermittent bug which causes the 'Link Detected'
field reported by the 'ethtool <iface>' command to be 'Yes' when
in fact, there is no link. This patch fixes the problem by
enabling temporary link polling when i40e_get_link_status returns
an error. This causes the driver to remember that an admin queue
command failed and polls, until the function returns with a success.
Change-Id: I64c69b008db4017b8729f3fc27b8f65c8fe2eaa0
Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a call to the mac_address_write admin q function during
power down to update the PRTPM_SAH/SAL registers with the MC_MAG_EN bit
thus enabling multicast magic packet wakeup.
A FW workaround is needed to write the multicast magic wake up enable
bit in the PRTPM_SAH register. The FW expects the mac address write
admin q cmd to be called first with one of the WRITE_TYPE_LAA flags
and then with the multicast relevant flags.
*Note: This solution only works for X722 devices currently. A PFR will
clear the previously mentioned bit by default, but X722 has support for a
WOL_PRESERVE_ON_PFR flag which prevents the bit from being cleared. Once
other devices support this flag, this solution should work as well.
Change-ID: I51bd5b8535bd9051c2676e27c999c1657f786827
Signed-off-by: Joshua Hay <joshua.a.hay@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Refactor how we add new filters to firmware to avoid a race condition
that can occur due to removing filters from the hash temporarily.
To understand the race condition, suppose that you have a number of MAC
filters, but have not yet added any VLANs. Now, add two VLANs in rapid
succession. A possible resulting flow would look something like the
following:
(1) lock hash for add VLAN
(2) add the new MAC/VLAN combos for each current MAC filter
(3) unlock hash
(4) lock hash for filter sync
(5) notice that we have a VLAN, so prepare to update all MAC filters
with VLAN=-1 to be VLAN=0.
(6) move NEW and REMOVE filters to temporary list
(7) unlock hash
(8) lock hash for add VLAN
(9) add new MAC/VLAN combos. Notice that no MAC filters are currently in
the hash list, so we don't add any VLANs <--- BUG!
(10) unlock hash
(11) sync the temporary lists to firmware
(12) lock hash for post-sync
(13) move the temporary elements back to the main list
....
Because we take filters out of the main hash into temporary lists, we
introduce a narrow window where it is possible that other callers to the
list will not see some of the filters which were previously added but
have not yet been finalized. This results in sometimes dropping VLAN
additions, and could also result in failing to add a MAC address on the
newly added VLAN.
One obvious way to avoid this race condition would be to lock the entire
firmware process. Unfortunately this does not work because adminq
firmware commands take a mutex which results in a sleep while atomic
BUG(). So, we can't use the simplest approach.
An alternative approach is to simply not remove the filters from the
hash list while adding. Instead, add an i40e_new_mac_filter structure
which we will use to track added filters. This avoids the need to remove
the filter from the hash list. We'll store a pointer to the original
i40e_mac_filter, along with our own copy of the state.
We won't update the state directly, so as to avoid race with other code
that may modify the state while under the lock. We are safe to read
f->macaddr and f->vlan since these only change in two locations. The
first is on filter creation, which must have already occurred. The
second is inside i40e_correct_vlan_filters which was previously run
after creation of this object and can't be run again until after. Thus,
we should be safe to read the MAC address and VLAN while outside the
lock.
We also aren't going to run into a use-after-free issue because the only
place where we free filters is when they are marked FAILED or when we
remove them inside the sync subtask. Since the subtask has its own
critical flag to prevent duplicate runs, we know this won't happen. We
also know that the only location to transition a filter from NEW to
FAILED is inside the subtask also, so we aren't worried about that
either.
Use the wrapper i40e_new_mac_filter for additions, and once we've
finalized the addition to firmware, we will update the filter state
inside a lock, and then free the wrapper structure.
In order to avoid a possible race condition with filter deletion, we
won't update the original filter state unless it is still
I40E_FILTER_NEW when we finish the firmware sync.
This approach is more complex, but avoids race conditions related to
filters being temporarily removed from the list. We do not need the same
behavior for deletion because we always unconditionally removed the
filters from the list regardless of the firmware status.
Change-Id: I14b74bc2301f8e69433fbe77ebca532db20c5317
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
After refactoring the client open and close code, this is no longer
needed. Remove it.
Change-ID: If8e6e32baa354d857c2fd8b2f19404f1786011c4
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
I40E_MAC_X710 was supposed to be for 10G and I40E_MAC_XL710
was supposed to be for 40G. But function i40e_is_mac_710
sets I40E_MAC_XL710 for all device IDS, I40E_MAC_X710 is not
used at all. As there is nothing to compare there is no need
for this function. Thus deprecating this extra macro and
removing this function entirely and replacing it with a direct
check.
Change-ID: I7d1769954dccd574a290ac04adb836ebd156730e
Signed-off-by: Bimmy Pujari <bimmy.pujari@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use __i40e_del_filter instead of using i40e_del_filter() which will
avoid doing an additional search to delete a filter we already have the
pointer for.
Change-ID: Iea5a7e3cafbf8c682ed9d3b6c69cf5ff53f44daf
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These functions purpose is to add a new MAC filter correctly, whether
we're using VLANs or not. Their goal is to ensure that all active VLANs
get the new MAC filter. Rename them so that their intent is clear. They
function correctly regardless of whether we have any active VLANs or
only have I40E_VLAN_ANY filters. The new names convey how they function
in a more clear manner.
Change-ID: Iec1961f968c0223a7132724a74e26a665750b107
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that we have the separate i40e_(add|rm)_vlan_all_mac functions, we
should not be using the i40e_vsi_kill_vlan or i40e_vsi_add_vlan
functions when PVID is set or when VID is less than 1. This allows us to
remove some checks in i40e_vsi_add_vlan and ensures that callers which
need to handle VID=0 or VID=-1 don't accidentally invoke the VLAN mode
handling used to convert filters when entering VLAN mode. We also update
the functions to take u16 instead of s16 as well since they no longer
expect to be called with VID=I40E_VLAN_ANY.
Change-ID: Ibddf44a8bb840dde8ceef2a4fdb92fd953b05a57
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The network device operation for reading statistics is only called
in one place, and it ignores the return value. Having a structure
return value is potentially confusing because some future driver could
incorrectly assume that the return value was used.
Fix all drivers with ndo_get_stats64 to have a void function.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current flow for adding or updating the PVID for a VF uses
i40e_vsi_add_vlan and i40e_vsi_kill_vlan which each take, then release
the hash lock. In addition the two functions also must take special care
that they do not perform VLAN mode changes as this will make the code in
i40e_ndo_set_vf_port_vlan behave incorrectly.
Fix these issues by using the new helper functions i40e_add_vlan_all_mac
and i40e_rm_vlan_all_mac which expect the hash lock to already be taken.
Additionally these functions do not perform any state updates in regards
to VLAN mode, so they are safe to use in the PVID update flow.
It should be noted that we don't need the VLAN mode update code here,
because there are only a few flows here.
(a) we're adding a new PVID
In this case, if we already had VLAN filters the VSI is knocked
offline so we don't need to worry about pre-existing VLAN filters
(b) we're replacing an existing PVID
In this case, we can't have any VLAN filters except those with the old
PVID which we already take care of manually.
(c) we're removing an existing PVID
Similarly to above, we can't have any existing VLAN filters except
those with the old PVID which we already take care of correctly.
Because of this, we do not need (or even want) the special accounting
done in i40e_vsi_add_vlan, so use of the helpers is a saner alternative.
It also opens the door for a future patch which will refactor the flow
of i40e_vsi_add_vlan now that it is not needed in this function.
Change-ID: Ia841f63da94e12b106f41cf7d28ce8ce92f2ad99
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A product decision has been made to defeature detection of PTP frames
over L4 (UDP) on the XL710 MAC. Do not advertise support for L4
timestamping.
Change-ID: I41fbb0f84ebb27c43e23098c08156f2625c6ee06
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Before this patch "ethtool -p" was not blinking the LEDs on boards
with 1G BaseT PHYs.
This commit identifies 1G BaseT boards as having the LEDs connected
to the MAC. Also, renamed the flag to be more descriptive of usage.
The flag is now I40E_FLAG_PHY_CONTROLS_LEDS.
Change-ID: I4eb741da9780da7849ddf2dc4c0cb27ffa42a801
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch makes the driver log link speed change. Before applying the
patch link messages were printed only on state change. Now message is
printed when link is brought up or down and when speed changes.
Change-ID: Ifbee14b4b16c24967450b3cecac6e8351dcc8f74
Signed-off-by: Filip Sadowski <filip.sadowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the problem where the ethtool Supported link
modes list backplane interfaces on X722 devices for 10GbE with
SFP+ and Cortina retimer. This patch fixes the problem by setting
and using a flag for this particular device since the backplane
interface is only between the internal PHY and the retimer and it
should not be seen by the user as they cannot use it.
Without this patch, the user wrongly thinks that backplane interfaces
are supported on their device when they actually are not.
Change-ID: I3882bc2928431d48a2db03a51a713a1f681a79e9
Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Removed some of unnecessary if statements and unreachable code found by
static code analysis tool.
The return value of i40e_vsi_control_rings(..., false) is always 0. So,
test for non-zero will never be true. The function has been split into
"int i40e_vsi_start_rings()" and "void i40e_vsi_stop_rings()" for better
understanding.
Similarly, the function i40e_vsi_kill_vlan() never fails. So, checking
for return value is also unnecessary. Function definition changed to void.
The i40e_loopback_test() function is not implemented. The function and
all references to loopback testing were removed.
Change-ID: Id45cf66f6689ce2bc4e887de13f073e30e8431bd
Signed-off-by: Filip Sadowski <filip.sadowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a common method for finding a VSI by type. The main
motivation for doing this is that the Flow Director path actually had two
ways of handling this, one stopped on first match and one did not. This
patch makes it so that all callers of this function will get the same
approach for finding a VSI.
Change-ID: Ibf25de8acd8466582520694424aa87da66965fbd
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Bimmy Pujari <bimmy.pujari@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The current Rx timestamp hang logic is not very robust because it does
not notice a register is hung until all four timestamps have been
latched and we wait a full 5 seconds. Replace this logic with a newer Rx
hang detection based on storing the jiffies when we first notice
a receive timestamp event. We store each register's time separately,
along with a flag indicating if it is currently latched. Upon first
transitioning to latch, we will update the latch_events[i] jiffies
value. This indicates the time we first noticed this event. The watchdog
routine will simply check that the either the flag has been cleared, or
we have passed at least one second. In this case, it is able to clear
the Rx timestamp register under the assumption that it was for a dropped
frame. The benefit if this strategy is that we should be able to
detect and clear out stalled RXTIME_H registers before we exhaust the
supply of 4, and avoid complete stall of Rx timestamp events.
Change-ID: Id55458c0cd7a5dd0c951ff2b8ac0b2509364131f
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We need a locking mechanism to protect the hardware SYSTIME register
which is split over 2 values, and has internal hardware latching. We
can't allow multiple accesses at the same time. However....
The spinlock_t is overkill here, especially use of spin_lock_irqsave,
since every PTP access will halt hardirqs. Notice that the only places
which need the SYSTIME value are user context and are capable of sleeping.
Thus, it is safe to use a mutex here instead of the spinlock.
Change-ID: I971761a89b58c6aad953590162e85a327fbba232
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We determine that a VSI is in vlan_mode whenever it has any filters
with a VLAN other than -1 (I40E_VLAN_ALL). The previous method of doing
so was to perform a loop whenever we needed the check. However, we can
notice that only place where filters are added (i40e_add_filter) can
change the condition from false to true, and the only place we can
return to false is in i40e_vsi_sync_filters_subtask. Thus, we can remove
the loop and use a boolean directly.
Doing this avoids looping over filters repeatedly especially while we're
already inside a loop over all the filters. This should reduce the
latency of filter operations throughout the driver.
Change-ID: Iafde08df588da2a2ea666997d05e11fad8edc338
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Replace the mac_filter_list with a static size hash table of 8bits. The
primary advantage of this is a decrease in latency of operations related
to searching for specific MAC filters, including .set_rx_mode. Using
a linked list resulted in several locations which were O(n^2). Using
a hash table should give us latency growth closer to O(n*log(n)).
Change-ID: I5330bd04053b880e670210933e35830b95948ebb
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
The kernel provides __dev_uc_sync and __dev_mc_sync in order for drivers
which need individual notification of add and delete for each filter.
These functions allow us to vastly simplify our .set_rx_mode handler. We
need to implement two functions for sync and unsync which add and remove
filters respectively.
This change avoids a very complex and inefficient algorithm which
resulted in an abnormal latency for the .set_rx_mode NDO operation. The
resulting code after this change is more readable, more efficient, and
less code.
Due to the callback signature used by these functions we also must
update several other functions to take a const u8 * pointer.
Change-Id: I2ca7fd4e10c0c07ed2291db1ea41bf5987fc6474
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Originally the is_vf and is_netdev fields were added in order to
distinguish between VF and netdev filters in a single VSI. However, it
can be noted that we use separate VSI for SRIOV VFs and for netdev VSI.
Thus, since a single VSI should only ever have one type of filter, we
can simply remove the checks and remove the typing.
In a similar fashion, we can note that the only remaining way to get
multiple filters of a single type is through a debug command that was
added to debugfs. This command is useless in practice, and results in
causing bugs if we keep counter tracking but lose the is_vf and
is_netdev protections as desired above.
Since the only time we'd actually have a counter value besides 0 and
1 is through use of this debugfs hook, we can remove this unnecessary
command, and the entire counter logic it required.
We vastly simplify mac filters by removing
(a) the distinction between VF and netdev filters
(b) counting logic
(c) the ability to add and remove filters bypassing the stack via debugfs
Change-ID: Idf916dd2a1159b1188ddbab5bef6b85ea6bf27d9
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mostly simple overlapping changes.
For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
There exists a bug in which a 'perfect storm' can occur and cause
interrupts to fail to be correctly affinitized. This causes unexpected
behavior and has a substantial impact on performance when it happens.
The bug occurs if there is heavy traffic, any number of CPUs that have
an i40e interrupt are pegged at 100%, and the interrupt afffinity for
those CPUs is changed. Instead of moving to the new CPU, the interrupt
continues to be polled while there is heavy traffic.
The bug is most readily realized as the driver is first brought up and
all interrupts start on CPU0. If there is heavy traffic and the
interrupt starts polling before the interrupt is affinitized, the
interrupt will be stuck on CPU0 until traffic stops. The bug, however,
can also be wrought out more simply by affinitizing all the interrupts
to a single CPU and then attempting to move any of those interrupts off
while there is heavy traffic.
This patch fixes the bug by registering for update notifications from
the kernel when the interrupt affinity changes. When that fires, we
cache the intended affinity mask. Then, while polling, if the cpu is
pegged at 100% and we failed to clean the rings, we check to make sure
we have the correct affinity and stop polling if we're firing on the
wrong CPU. When the kernel successfully moves the interrupt, it will
start polling on the correct CPU. The performance impact is minimal
since the only time this section gets executed is when performance is
already compromised by the CPU.
Change-ID: I4410a880159b9dba1f8297aa72bef36dca34e830
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function is not used so there is no need to carry it forward. I have
plans to add a slightly different function that can be inlined to handle
the same kind of functionality.
Change-ID: Ie2dfcb189dc75e5fbc156bac23003e3b4210ae0f
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
in commit a036244c06 a fix
was put into place to avoid a kernel panic when a non-
supported traffic class configuration was put into place
and then lldp was enabled/disabled on the link partner
switch. This fix caused it to be necessary to
unload/reload the driver to reenable DCB once a supported
TC config was in place.
The root cause of the original panic was that the function
i40e_pf_get_default_tc was allowing for a default TC other
than TC 0, and only TC 0 is supported as a default.
This patch removes the get_default_tc function and replaces
it with a #define since there is only one TC supported as
a default.
Change-Id: I448371974e946386d0a7718d73668b450b7c72ef
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Ronald Bynoe <ronald.j.bynoe@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This interface was only ever meant for debug only. Since it is not
supposed to be here we are removing it.
Change-ID: Id771a1e5e7d3e2b4b7f56591b61fb48c921e1d04
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch increases minimum number of allocated VSIs, so as to resolve
failure adding VSI for VF when 64-VFs assigned to a PF. The driver
supports up to 128 VFs per device, users can decide to enable up to
64-VFs on a single PF, especially 2 X 40 devices. In that scenario, with
VMDq co-existence, there would be starvation of VSIs - with this patch,
supported features would have enough VSIs for configuration now.
Change-ID: If084f4cd823667af8fe7fdc11489c705b32039d5
Signed-off-by: Akeem Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previously, when using ethtool to change the RSS hash key, ethtool would
report back saying the old key was still being used and no error was
reported. It was unclear whether it was being reported incorrectly or
being set incorrectly. Debugging revealed 'i40e_set_rxfh()' returned
zero immediately instead of setting the key because a user defined
indirection table is not supplied when changing the hash key.
This fix instead changes it such that if an indirection table is not
supplied, then a default one is created and the hash key is now
correctly set.
Change-ID: Iddb621897ecf208650272b7ee46702cad7b69a71
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Several defines and code comments were indented with spaces instead
of tabs, correct the issue to make indentation consistent.
Change-ID: I0dc6bbb990ec4a9e856acc9ec526d876181f092c
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Use __stringify instead.
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch implements a feature change which allows using ethtool to set
RSS hash opts using less than four parameters if desired.
Change-ID: I0fbb91255d81e997c456697c21ac39cc9754821b
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Properly track filter adds and deletes so the driver doesn't lose filters
during resets and up/down cycles. Add a tracking mechanism so that the
driver knows when to enter and leave promiscuous mode.
Implement a simple state machine so the driver can track the status of
each filter throughout its lifecycle. Properly manage the overflow promiscuous
state for the each VSI, and provide a way for the driver to detect when to exit
overflow promiscuous mode.
Remove all possible default MAC filters that the firmware may have set up so
that the driver can manage these correctly, particularly when VLANs come into
play. Remove the LAA flag for filters; instead just send whatever we get through
set_mac to the firmware as the LAA for wakeup purposes.
Finally, add the state of each filter to debugfs output so we can see what's
going on inside the driver's pointy little head.
Change-ID: I97c5e366fac2254fa01eaff4f65c0af61dcf2e1f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On systems with 128 CPUs, turning off TSO results in errors,
i40e 0000:03:00.0: failed to get tracking for 1 vectors for VSI 400, err=-12
i40e 0000:03:00.0: Couldn't create FDir VSI
i40e 0000:03:00.0: i40e_ptp_init: PTP not supported on eth0
i40e 0000:03:00.0: couldn't add VEB, err I40E_ERR_ADMIN_QUEUE_ERROR aq_err I40E_AQ_RC_ENOENT
i40e 0000:03:00.0: rebuild of switch failed: -1, will try to set up simple PF connection
i40e 0000:03:00.0 eth0: adding 00:10:e0:8a:24:b6 vid=0
Enabling FD_SB without checking availability of MSI-X vector is the
root cause. This change adds necessary check.
Signed-off-by: Tushar Dave <tushar.n.dave@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds priv-flag knob to configure global true promisc
support. With this patch the user can decide the flavor of
promiscuous that the VFs will see when promiscuous mode is enabled
on the interface. Since this a global setting for the whole device,
the priv-flag is exposed only on the first PF of the device.
The default is true promisc support is off, which means the promisc
mode for the VF will be limited/defport mode.
For the PF, we still will be in limited promisc unless in MFP mode
irrespective of the flavor picked through this knob.
Usage:
On PF0
ethtool --show-priv-flags p261p1
Private flags for p261p1:
MFP : off
LinkPolling : off
flow-director-atr : on
veb-stats : off
hw-atr-eviction : off
vf-true-promisc-support: off
to enable setting true promisc
ethtool --set-priv-flags p261p1 vf-true-promisc-support on
At this point if the VF is set to trust and promisc is enabled
on the VF through
ip link set ... promisc on
The VF/VFs will be able to see ALL ingress traffic
Change-Id: I8fac4b6eb1af9ca77b5376b79c50bdce5055bd94
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add flag to tell firmware to disable link on all ports.
This patch changes the bits set for telling firmware the PHY needs
to be modified by driver. Without this patch, the setting will only
set that mode for the current port on the device. Because the
MDIO interface is common for the copper device. The command needs to
set the mode for all ports.
Change-ID: I8baa7da91d384291ac95b41ae1a516604f8eb67f
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The hardware supports a 16 byte descriptor for receive, but the
driver was never using it in production. There was no performance
benefit to the real driver of 16 byte descriptors, so drop a whole
lot of complexity while getting rid of the code.
Also since the previous patch made us use no-split mode all the
time, drop any support in the driver for any other value in dtype
and assume it is always zero (aka no-split).
Hooray for code removal!
Change-ID: I2257e902e4dad84a07b94db6d2e6f4ce69b27bc0
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is part 1 of the Rx refactor series, just including
changes to i40e.
This refactor aligns the receive routine with the one in
ixgbe which was highly optimized. This reduces the code
we have to maintain and allows for (hopefully) more readable
and maintainable RX hot path.
In order to do this:
- consolidate the receive path into a single function that doesn't
use packet split but *does* use pages for Rx buffers.
- remove the old _1buf routine
- consolidate several routines into helper functions
- remove ethtool control over packet split
Change-ID: I5ca100721de65992aa0114f8b4bac844b84758e0
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As part of preparation for the rx-refactor, remove the
packet split receive routine and ancillary code.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was all over the place using signed or unsigned types
for vf_id, when it should always be signed.
This fixes warnings of type unsafe comparisons from gcc with W=2.
Change-Id: I2cb681f83d0f68ca124d2e4131e4ac0d9f8a6b22
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for configuring RSS on behalf of the VFs. This removes the
burden of dealing with different hardware interfaces from the VF
drivers, allowing for better future compatibility.
Change-ID: Icea75d3f37241ee8e447be5779e5abb53ddf04c0
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes the duplicate definition of I40E_MAX_USER_PRIORITY
in i40e.h that is not needed.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Calling dev_close() causes IFF_UP to be cleared which will remove the
interfaces routes and some addresses. That's probably not what the user
intended when running the offline selftest. Besides this does not happen
if the interface is brought down before the test, so the current
behaviour is inconsistent.
Instead call the net_device_ops ndo_stop function directly and avoid
touching IFF_UP at all.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
- A few minor core fixups needed for the next patch series
- The IB SRIOV series. This has bounced around for several versions.
Of note is the fact that the first patch in this series effects
the net core. It was directed to netdev and DaveM for each iteration
of the series (three versions total). Dave did not object, but did
not respond either. I've taken this as permission to move forward
with the series.
- The new Intel X722 iWARP driver
- A huge set of updates to the Intel hfi1 driver. Of particular interest
here is that we have left the driver in staging since it still has an
API that people object to. Intel is working on a fix, but getting
these patches in now helps keep me sane as the upstream and Intel's
trees were over 300 patches apart.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=t2Ko
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull more rdma updates from Doug Ledford:
"Round two of 4.6 merge window patches.
This is a monster pull request. I held off on the hfi1 driver updates
(the hfi1 driver is intimately tied to the qib driver and the new
rdmavt software library that was created to help both of them) in my
first pull request. The hfi1/qib/rdmavt update is probably 90% of
this pull request. The hfi1 driver is being left in staging so that
it can be fixed up in regards to the API that Al and yourself didn't
like. Intel has agreed to do the work, but in the meantime, this
clears out 300+ patches in the backlog queue and brings my tree and
their tree closer to sync.
This also includes about 10 patches to the core and a few to mlx5 to
create an infrastructure for configuring SRIOV ports on IB devices.
That series includes one patch to the net core that we sent to netdev@
and Dave Miller with each of the three revisions to the series. We
didn't get any response to the patch, so we took that as implicit
approval.
Finally, this series includes Intel's new iWARP driver for their x722
cards. It's not nearly the beast as the hfi1 driver. It also has a
linux-next merge issue, but that has been resolved and it now passes
just fine.
Summary:
- A few minor core fixups needed for the next patch series
- The IB SRIOV series. This has bounced around for several versions.
Of note is the fact that the first patch in this series effects the
net core. It was directed to netdev and DaveM for each iteration
of the series (three versions total). Dave did not object, but did
not respond either. I've taken this as permission to move forward
with the series.
- The new Intel X722 iWARP driver
- A huge set of updates to the Intel hfi1 driver. Of particular
interest here is that we have left the driver in staging since it
still has an API that people object to. Intel is working on a fix,
but getting these patches in now helps keep me sane as the upstream
and Intel's trees were over 300 patches apart"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (362 commits)
IB/ipoib: Allow mcast packets from other VFs
IB/mlx5: Implement callbacks for manipulating VFs
net/mlx5_core: Implement modify HCA vport command
net/mlx5_core: Add VF param when querying vport counter
IB/ipoib: Add ndo operations for configuring VFs
IB/core: Add interfaces to control VF attributes
IB/core: Support accessing SA in virtualized environment
IB/core: Add subnet prefix to port info
IB/mlx5: Fix decision on using MAD_IFC
net/core: Add support for configuring VF GUIDs
IB/{core, ulp} Support above 32 possible device capability flags
IB/core: Replace setting the zero values in ib_uverbs_ex_query_device
net/mlx5_core: Introduce offload arithmetic hardware capabilities
net/mlx5_core: Refactor device capability function
net/mlx5_core: Fix caching ATOMIC endian mode capability
ib_srpt: fix a WARN_ON() message
i40iw: Replace the obsolete crypto hash interface with shash
IB/hfi1: Add SDMA cache eviction algorithm
IB/hfi1: Switch to using the pin query function
IB/hfi1: Specify mm when releasing pages
...
This patch adds a Client interface for i40iw driver
support. Also expands the Virtchannel to support messages
from i40evf driver on behalf of i40iwvf driver.
This client API is used by the i40iw and i40iwvf driver
to access the core driver resources brokered by the i40e driver.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
For i40e driver, each vector has its own ITR register. However, there
are no concept of queue-specific settings in the driver proper. Only
global variable is used to store ITR values. That will cause problems
especially when resetting the vector. The specific ITR values could be
lost.
This patch move rx_itr_setting and tx_itr_setting to i40e_ring to store
specific ITR register for each queue.
i40e_get_coalesce and i40e_set_coalesce are also modified accordingly to
support queue-specific settings. To make it compatible with old ethtool,
if user doesn't specify the queue number, i40e_get_coalesce will return
queue 0's value. While i40e_set_coalesce will apply value to all queues.
Signed-off-by: Kan Liang <kan.liang@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a problem where the ethtool identify adapter
functionality did not work for some copper PHY's. Without this
patch, the blink led functionality fails on some parts. This
patch adds PHY write code to blink led's on parts where this
functionality is contained in the PHY rather than the MAC.
Change-ID: Iee7b3453f61d5ffd0b3d03f720ee4f17f919fcc2
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fixed mapping of SEID is removed from specification. Hence
this patch removes code which was using hard coded base VEB SEID.
Changed FCoE code to use "hw->pf_id" to obtain correct "idx"
and verified.
Removed defines for BASE VSI/VEB SEID and BASE_PF_SEID since it
is not used anymore.
Change-ID: Id507cf4b1fae1c0145e3f08ae9ea5846ea5840de
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a workaround for cases where we might have
interrupts that got lost but WB happened.
If that happens without this patch we will see a tx_timeout.
To work around it, this patch goes ahead and reschedules NAPI
in that situation, if NAPI is not already scheduled.
We also add a counter in ethtool to keep track of when
we detect a case of tx_lost_interrupt.
Note: napi_reschedule() can be safely called from process/service_task
context and is done in other drivers as well without an issue.
Change-ID: I00f98f1ce3774524d9421227652bef20fcbd0d20
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
While re-enabling interrupts the driver would clear all pending
causes. This meant that if an interrupt was generated while the driver
was cleaning or polling with interrupts disabled, then that interrupt
was lost. This could cause a queue to become dead, especially for
receive. Refactored the enable_icr0 function in order to allow
it to be decided by the caller whether the CLEARPBA (clear pending
events) bit will be set while re-enabling the interrupt.
Also update copyright year in file headers.
Change-ID: Ic1db100a05e13c98919057696db147a258ca365a
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
