The interface's immediate purpose is to do synchronous timestamp queries
as required by GL_TIMESTAMP. The GPU has a register for reading the
timestamp but because that would normally require root access through
libpciaccess, the IOCTL can provide this service instead.
Currently the implementation whitelists only the render ring timestamp
register, because that is the only thing we need to expose at this time.
v2: make size implicit based on the register offset
Add a generation check
Reviewed-by: Eric Anholt <eric@anholt.net>
Cc: Jacek Lawrynowicz <jacek.lawrynowicz@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: fixup the ioctl numerb:]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch adds support for the ns2501 DVO, found in some older Fujitsu/Siemens Labtops.
It is in the state of "works for me".
Includes now proper DPMS support. Includes switching between resolutions -
from 640x480 to 1024x768.
Currently assumes that the native display resolution is 1024x768.
The ns2501 seems to be rather critical - if the output PLL is not
running, the chip doesn't seem to be clocked and then doesn't react
on i2c messages. Thus, a quick'n-dirty trick ensures that the DVO
is active before submitting any i2c messages to it. This is
probably to be reviewed.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=17902
Signed-off-by: Thomas Richter <thor@math.tu-berlin.de>
[danvet: fixup whitespace fail.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This will be needed for Haswell, but already has its uses here.
This patch started as a small patch written patch by Shobhit Kumar,
but it has changed so much that none of its original lines remain.
Credits-to: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have some common code that we always run before calling
intel_dp_set_link_train. This common code sets the correct training
patterns to the DP variable. If we add more calls to
intel_dp_set_link_train, we'll also have to duplicate this common
code. So instead of repeating this code whenever we call
intel_dp_set_link_train, we move the code to inside the function: now
we check which training pattern we're going to set and then we set the
DP register according to it.
One of the side-effects of this change is that now we never forget to
mask the training pattern bits before changing them. It looks like
this was working before because we were first masking the bits, then
writing 00, 01 and then 11.
This patch also enables us to use the intel_dp_set_link_train function
when disabling link training: in this case we need to avoid writing
the DP_TRAINING_LANE*_SET AUX commands.
As a bonus, the big intel_dp_{start,complete}_link_train functions
will get smaller and a little bit easier to read.
Version 2 changes:
- Rewrite commit message.
- Also clear the training pattern bits before changing them.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of having a giant if cascade to figure this out according to
the passed-in register. We could do quite a bit more cleaning up and
all by using the port at more places, but I think this should be part
of a bigger rework to introduce a struct intel_digital_port which
would keep track of all these things. I guess this will be part of
some haswell-DP-induced refactoring.
For now this rips out the big cascade, which is what annoyed me so
much.
v2: Add port variable name back for the func decl (I've tried to trick
myself below the 80 char limit).
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Intel hw only has one MUX for encoders, so outputs are either not
cloneable or all in the same group of cloneable outputs. This neatly
simplifies the code and allows us to ditch some ugly if cascades in
the dp and hdmi init code (well, we need these if cascades for other
stuff still, but that can be taken care of in follow-up patches).
Note that this changes two things:
- dvo can now be cloned with sdvo, but dvo is gen2 whereas sdvo is
gen3+, so no problem. Note that the old code had a bug and didn't
allow cloning crt with dvo (but only the other way round).
- sdvo-lvds can now be cloned with sdvo-non-tv. Spec says this won't
work, but the only reason I've found is that you can't use the
panel-fitter (used for lvds upscaling) with anything else. But we
don't use the panel fitter for sdvo-lvds. Imo this part of Bspec is
a) rather confusing b) mostly as a guideline to implementors (i.e.
explicitly stating what is already implicit from the spec, without
always going into the details of why). So I think we can ignore this
- worst case we'll get a bug report from a user with with sdvo-lvds
and sdvo-tmds and have to add that special case back in.
Because sdvo lvds is a bit special explain in comments why sdvo LVDS
outputs can be cloned, but native LVDS and eDP can't be cloned - we
use the panel fitter for the later, but not for sdvo.
Note that this also uncoditionally initializes the panel_vdd work used
by eDP. Trying to be clever doesn't buy us anything (but strange bugs)
and this way we can kill the is_edp check.
v2: Incorporate review from Paulo
- Add in a missing space.
- Pimp comment message to address his concerns.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Splitting them up between pch and gmch variants just makes it harder
to find things. Especially since the hotplug bits are actually valid
on earlier chips, too.
v2: Fixed the comment as pointed out by Paulo Zanoni.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When bug hunting, I found the interface to do_switch() overly
complicated and I believe festered the earlier bug. This aims to make
the code a little clearer.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move the DP structure to shared location so that it can be used from
within the ddi module.
Changes from Paulo:
- Move less code to intel_drv.h
- Remove #include statement
- Replace a tab with a space in train_set
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We now refuse to load on gen6+ if kms is not enabled:
commit 26394d9251
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Mon Mar 26 21:33:18 2012 +0200
drm/i915: refuse to load on gen6+ without kms
Which results in the drm core calling our lastclose function to clean
up the mess, but that one is neatly broken for such failure cases
since kms has been introduced in
commit 79e539453b
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Fri Nov 7 14:24:08 2008 -0800
DRM: i915: add mode setting support
Reported-and-tested-by: Paulo Zanoni <przanoni@gmail.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fixes failures in transform feedback on gen7 because our SOL_RESET
flag was setting the transform feedback offsets in the old context
(occasionally happened to be ours) instead of the new context.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
LVDS is the first output where dpms on/off and prepare/commit don't
perfectly match. Now the idea behind this special case seems to be
that for simple resolution changes on the LVDS we don't need to stop
the pipe, because (at least on newer chips) we can adjust the panel
fitter on the fly.
There are a few problems with the current code though:
- We still stop and restart the pipe unconditionally, because the crtc
helper code isn't flexible enough.
- We show some ugly flickering, especially when changing crtcs (this
the crtc helper would actually take into account, but we don't
implement the encoder->get_crtc callback required to make this work
properly).
So it doesn't even work as advertised. I agree that it would be nice
to do resolution changes on LVDS (and also eDP) whithout blacking the
screen where the panel fitter allows to do that. But imo we should
implement this as a special case a few layers up in the mode set code,
akin to how we already detect simple framebuffer changes (and only
update the required registers with ->mode_set_base).
Until this is all in place, make our lives easier and just rip it out.
Also note that this seems to fix actual bugs with enabling the lvds
output, see:
http://lists.freedesktop.org/archives/intel-gfx/2012-July/018614.html
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Giacomo Comes <comes@naic.edu>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Takashi Iwai <tiwai@suse.de>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to check that "ctx" is a valid pointer before dereferencing it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Otherwise we end up trying to unpin a freed object and BUG.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This prevents a WARN introduced with
commit de2b998552
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Jul 4 22:52:50 2012 +0200
drm/i915: don't return a spurious -EIO from intel_ring_begin
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The issue is that we stale data in the CPU caches, when we come to
swap-out the object, the CPU may short-circuit the reads from those
cacheline and so corrupt the context object.
Secondary, leaving the context object as being marked in the CPU write
domain whilst on the GPU active list is a bad idea and will throw
warnings later.
Note: Thanks to calling set_to_gtt_domain with write = false and not
setting any gpu write domain when putting a context object onto the
active list (when we switch away from it) the set_to_gtt_domain call
won't block.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Added a note to the commit message and a comment in the code
to explain the clever non-blocking trick.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As we take the struct_mutex lock to access the command-stream, there is
a possibility that we may need to wait for a GPU hang and so should make
the lock both interruptible and error-checking.
References: https://bugs.freedesktop.org/show_bug.cgi?id=50069
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we enable/disable the CPU backlight registers we can't forget to
enable/disable the PCH backlight registers. Since we're using the CPU
registers we should also unset the override bit.
Fixes a regression on the following commit:
drm/i915: properly enable the blc controller on the right pipe
The commit just deleted the code that sets the PCH registers, so it
was relying on the values set by the BIOS. I told my BIOS to boot on
the DVI monitor instead of the LVDS panel, so I noticed the bug.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we drop the breadcrumb request after a batch due to a signal for
example we aim to fix it up at the next opportunity. In this case we
emit a second batchbuffer with no waits upon the first and so no
opportunity to insert the missing request, so we need to emit the
missing flush for coherency. (Note that that invalidating the render
cache is the same as flushing it, so there should have been no
observable corruption.)
Note that beside simply adding the missing flush, avoiding potential
render corruption, this will also fix at least parts of the problem
introduced by some funny interaction of these two commits:
commit de2b998552
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Jul 4 22:52:50 2012 +0200
drm/i915: don't return a spurious -EIO from intel_ring_begin
which allowed intel_ring_begin to return -ERESTARTSYS and
commit cc889e0f6c
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Jun 13 20:45:19 2012 +0200
drm/i915: disable flushing_list/gpu_write_list
which essentially disabled the flushing list.
The issue happens when we submit a batch & emit it, but get
interrupted (thanks to the first patch) while trying to emit the
flush. On the next batch we still assume that the full gpu domain
handling is in effect and hence compute the invalidate&flushing
domains. But thanks to the 2nd patch we totally ignore these and only
invalidate all gpu domains, presuming that any required flushes have
been issued already. Which is wrong and eventually results in us
updating the new write_domain values with the computed
pending_write_domain values, which leaves an object with write_domain
== 0 on the gpu_write_list.
As soon as we try to unbind that object, things blow up.
Fix this by emitting the missing flush according to the new
ring->gpu_caches_dirty flag.
Note that this does _not_ fix all the current cases where we end up
with an object on the flushing_list that can't be flushed.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=52040
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Add bug explanation to commit message.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Or going from tiled to untiled may break.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
While debugging Haswell link train failures I observed that we never
try the maximum voltage configuration more than once consecutively. We
start the training, the monitor keeps telling us to increase the
voltage, then when we reach the maximum we just go back to the start
(because of the "memset" above "voltage_tries = 0"). When we reach
this point, we keep alternating between the maximum and the minimum
voltages until we give up.
The DP spec suggests that we should try the same voltage 5 times
before giving up. This patch makes us try the maximum voltage at
least 5 times before going back to the minimum voltages.
This patch does not fix any particular bug I'm aware of.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have way too much lying hardware to rely on a simple "does someone
answer on the ddc i2c address?" check. And now it's unused, so just
kill it.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Somehow detect_ddc manages to fall through all checks when we think
that something responds on the ddc i2c address, but the edid read
failed. Fix this up by explicitly checking for this case.
This fixes a regression on newer chips because since
commit aaa377302b
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sat Jun 16 15:30:32 2012 +0200
drm/i915/crt: Do not rely upon the HPD presence pin
we use ddc detection also on hotplug capable platforms. And one of
these reads all 0s for any i2c transaction if nothing is connected to
the vga port.
v2: Implement Chris Wilson's review:
- simplify logic, default to "nothing detected"
- kill stale comment
- BUG_ON(!crt->type != ANALOG)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=51900
Tested-by: Yang Guang <guang.a.yang@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I so totally suck.
This can cause a black screen if (for whatever reason) the bios
hasn't set this bit itself.
This regression has been introduced in
commit 7cf4160148
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Tue Jun 5 10:07:09 2012 +0200
drm/i915: clear up backlight #define confusion on gen4+
Tested-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Having had to dive into the bspec to understand what each stage of the
workaround meant, and how that the ring broadcasting IDLE corresponded
with the GT powering down the ring (i.e. rc6) add comments to aide
the next reader.
And since the register "is used to control all aspects of PSMI and power
saving functions" that makes it quite interesting to inspect with
regards to RC6 hangs, so add it to the error-state.
v2: Rediscover the piece of magic, set the RNCID to 0 before waiting for
the ring to wake up.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It never quite worked despite the numerous workarounds, yet I still see
people trying to use this hardware and filing bug reports. As we no
longer even try to implement the workarounds, since 6a233c7887
(drm/i915/ringbuffer: kill snb blt workaround), simply disable the ring.
v2: Add a message to inform the user about the limited capabilities of
their pre-production hardware.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This initializes power wells within the modeset_init_hw routine.
Testing has shown that this works for both driver load time and for
suspend-resume code paths.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is little point waking up every 10ms to service an interrupt which
we then promptly ignore. So only program the the PMIER to enable
interrupts for those events which we do handle, not all of them!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Eugeni Dodonov <eugeni.dodonov@intel.com>
Cc: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There were some fields missed. Daniel pointed this out in review, and I
know I fixed it, but something happened somehow and some time.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
*sigh* the docs had it spelled wrong, corrected it, and then proceeded
to re-do the original error. The original code preserved this history,
and this patch attempts to keep in sync with the current docs.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Userspace uses long in quite a few places more than the kernel. Which
gives me neat proof that I'm the only guy on this side of the galaxy
who ever tried to run glxgears on a 64bit machine with sis graphics on
linux.
Note that the longs in drm_sis_mem_t aren't aligned properly, so this
won't even work with 32bit userspace on 64bit kernel as-is. Hence the
patch can't break that, either.
Nope, I'm not nuts enough to write the 32bit ioctl compat layer for
this and test it with some wine app. Even though hunting the ebay
dungeons for a sis card actually supported by the mesa drivers casts
some doubts on this ...
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
With the last patch to ditch DMA_QUEUE support, we should be able
to call the dma cleanup uncoditionally, even when the master has
disappeared.
Do so because it just makes more sense.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Absolutely unused. All the values are only ever initialized and
then used at most in some debug printout functions.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Only one driver (i810) even sets that flag. Now the actual locking
code uncoditionally promotes lock->context to an unsigned int.
Closer inspection of the userspace reveals that the drm lock context
is defined as an unsigned int (at least on linux). I suspect we just
have a strange case of signedness confusion going on.
Tested on my i815, doesn't seem to break anything.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
All leftover users either haven't set DRIVER_HAVE_DMA, in which
case this will never be called, or use the drm_core implementation.
Call that directly in the only callsite.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The reclaim_buffers function of the savage driver actually wants to run
with the hw_lock held - at least there are printks in the call-chain
to that effect. But the drm core only calls reclaim_buffers as used
by savage _after_ forcefully dropping the hwlock (in case it's still
hold by the closing fd).
So do the same idlelock dance as for the other dma drivers and hope
that papers over any issues.
v2: Don't let the idlelock linger around.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: Tormod Volden <debian.tormod@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
i810 was the last user of this code, with that gone, kill it.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This reverts commit 6e877b576d,
reinstating the original commit:
commit 87499ffdcb
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Tue Oct 25 23:51:24 2011 +0200
drm/i810: cleanup reclaim_buffers
My dear old i815 always hits the deadlocked on reclaim_buffers
warning. Switch over to the idlelock duct-tape on hope that
works better. I've fired up my i815 and now closing glxgears doesn't
take 5 seconds anymore. \o/
The original problem with that was that I've moved it ahead in the
series so that it could be included despite some patches not being
ready quite yet. The little problem is that this patch required some
of the previous rework to work correctly.
Now that everything is in the right order again, this actually works
on my i810 and does speed up closing gl apps as the original commit
claimed. Without hanging the machine, as the revert says.
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The only two users are now folded into the drivers preclose functions,
so this is unused.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Like for via.
v2: Actually drop the idlelock again if taken.
v3: Fixup.
v4: Fixup the "has master" vs. "is master" confusion the refactor
introduced.
v5: Drop the idlelock in the early return path.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
A few things
- kill reclaim_buffers, it's never ever called because via does not set
DRIVER_HAVE_DMA
- inline the idlelock dance into the buffer reclaim logic and make it
a simple preclose cleanup function
- directly call the the dma_quiescent function and kill the needless
if check.
v2: Actually drop the idlelock when we take it. Reported by James
Simmons.
v3: Rebased onto latest drm-next.
v4: Fixup the refactor.
v5: More fixup the refactor - I've accidentally changed the check for
any master to checking whether the closing fd is the master.
v6: Don't forget to drop the idlelock in the early return path, too.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This ports over the dpms code from udlfb, and should mean
a better chance of turning on some udl devices.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This check the root ports supported link speeds and enables
GEN2 mode if the 5.0 GT link speed is available.
The first 3.0 cards are SI so they will probably need more investigation.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Print various CP register that have valuable informations regarding
GPU lockup.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
we are referencing the pointer after doing alloc_apertures,
as alloc_apertures kzallocs, the kzalloc may fail and we get a NULL.
so we need to check for NULL before we dereference this pointer
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This could previously fail if either of the enabled displays was using a
horizontal resolution that is a multiple of 128, and only the leftmost column
of the cursor was (supposed to be) visible at the right edge of that display.
The solution is to move the cursor one pixel to the left in that case.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=33183
Cc: stable@vger.kernel.org
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The passed mode must not be modified by the operation, make it const.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
