A block driver may start cleaning up resources needed by its
request_fn as soon as blk_cleanup_queue() finished, so request_fn
must not be invoked after draining finished. This is important
when blk_run_queue() is invoked without any requests in progress.
As an example, if blk_drain_queue() and scsi_run_queue() run in
parallel, blk_drain_queue() may have finished all requests after
scsi_run_queue() has taken a SCSI device off the starved list but
before that last function has had a chance to run the queue.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: Chanho Min <chanho.min@lge.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Let the caller of blk_drain_queue() obtain the queue lock to improve
readability of the patch called "Avoid that request_fn is invoked on
a dead queue".
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Chanho Min <chanho.min@lge.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
QUEUE_FLAG_DEAD is used to indicate that queuing new requests must
stop. After this flag has been set queue draining starts. However,
during the queue draining phase it is still safe to invoke the
queue's request_fn, so QUEUE_FLAG_DYING is a better name for this
flag.
This patch has been generated by running the following command
over the kernel source tree:
git grep -lEw 'blk_queue_dead|QUEUE_FLAG_DEAD' |
xargs sed -i.tmp -e 's/blk_queue_dead/blk_queue_dying/g' \
-e 's/QUEUE_FLAG_DEAD/QUEUE_FLAG_DYING/g'; \
sed -i.tmp -e "s/QUEUE_FLAG_DYING$(printf \\t)*5/QUEUE_FLAG_DYING$(printf \\t)5/g" \
include/linux/blkdev.h; \
sed -i.tmp -e 's/ DEAD/ DYING/g' -e 's/dead queue/a dying queue/' \
-e 's/Dead queue/A dying queue/' block/blk-core.c
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Chanho Min <chanho.min@lge.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Before queuing the flip but crucially after attaching the unpin-work to
the crtc, we continue to setup the unpin-work. However, should the
hardware fire early, we see the connected unpin-work and queue the task.
The task then promptly runs and unpins the fb before we finish taking
the required references or even pinning it... Havoc.
To close the race, we use the flip-pending atomic to indicate when the
flip is finally setup and enqueued. So during the flip-done processing,
we can check more accurately whether the flip was expected.
v2: Add the appropriate mb() to ensure that the writes to the page-flip
worker are complete prior to marking it active and emitting the MI_FLIP.
On the read side, the mb should be enforced by the spinlocks.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
[danvet: Review the barriers a bit, we need a write barrier both
before and after updating ->pending. Similarly we need a read barrier
in the interrupt handler both before and after reading ->pending. With
well-ordered irqs only one barrier in each place should be required,
but since this patch explicitly sets out to combat spurious interrupts
with is staged activation of the unpin work we need to go full-bore on
the barriers, too. Discussed with Chris Wilson on irc and changes
acked by him.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If the sdata work is pending while the interface is stopped,
we currently flush it. If it's not running this means waiting
for it to run, which could take a while if the workqueue is
backlogged. However, the work exits right away if it starts
to run while the interface is already stopping. There's no
point in waiting for that, so use cancel_work_sync() instead.
Reported-by: Ben Greear <greearb@candelatech.com>
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is really a 3-bit field, not a single bit,
so declare a mask and shift. Also fix hwsim, it
advertises the maximum possible.
While at it reindent all the defines using tabs
instead of spaces.
Change-Id: I7cd81c0d72f76deb5010aba5bfa3dd312006e898
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previously, mesh peering frames from a STA without a station
entry were being dropped.
Mesh Peering Open and other frames (WLAN_CATEGORY_SELF_PROTECTED)
are valid mesh peering frames even if received from a yet unknown
station; the STA entry will be created in mesh_peer_init later.
The problem didn't occur previously since both STAs receive each
other's beacons which created the STA entry. However, this causes
an unnecessary delay and beacons might not be received if either
node is in PS mode.
Signed-off-by: Marco Porsch <marco.porsch@etit.tu-chemnitz.de>
[reword commit log a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ret_count has to be at least 3, as we have to count the 2 bytes that are used
for the size of the reply. Without this, memcpy() might be called with zero or
negative count.
Reported-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The previous memcpy implementation relied on the size advertized by the
device. There were no guarantees that buf was big enough.
Some gymnastic is also required with the +2/-2 to take into account
the first 2 bytes of the returned buffer where the total returned
length is supplied by the device.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There is no point in keeping the irq in i2c_hid as it's already
there in client.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Simplifies i2c_hid_alloc_buffers tests, and makes this function
responsible of the assignment of ihid->bufsize.
The condition for the reallocation in i2c_hid_start is then simpler.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
HID descriptors contains 4 bytes of reserved field.
The previous implementation was overriding the next fields in struct i2c_hid.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Merely reorganizing documentation. No functional changes. It makes more
sense for the gpio-leds binding to be grouped with other led bindings
than with gpio drivers.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
I've legally changed my name with New York State, the US Social Security
Administration, et al. This patch propagates the name change and change
in initials and login to comments in the kernel source as well.
Signed-off-by: Nadia Yvette Chambers <nyc@holomorphy.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The compatible property in device tree "crypto" node has been enhanced
to provide SEC ERA information to the applications.
Signed-off-by: Vakul Garg <vakul@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The test vectors for 'xts(aes)' contain superfluous initializers.
Remove them.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When in fips mode, compression algoritms fails to initialize,
e.g. modprobe ubifs returns
UBIFS error: compr_init: cannot initialize compressor lzo, error -2
FIPS mode should not care about compression algoritms at all.
Patch just set fips_enabled flag to 1 to all compression algorithms
managed by testmgr.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Currently alg_test_null entries set .suite values to zero, which is unneeded.
So perform clean-up of null test entries.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Remove incorrect fips_allowed from camellia null-test entries. Caused by
incorrect copy-paste of aes-aesni null-tests into camellia-aesni null-tests.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
CAST5 and CAST6 both use same lookup tables, which can be moved shared module
'cast_common'.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Provide robustness against low quality FLL sync clocks by increasing the
timeout for lock to an absurdly high point; we should never get anywhere
near hitting the timeout in a real system unless it is failing.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There are two cases we need to adjust page size in set_spte:
1): the one is other vcpu creates new sp in the window between mapping_level()
and acquiring mmu-lock.
2): the another case is the new sp is created by itself (page-fault path) when
guest uses the target gfn as its page table.
In current code, set_spte drop the spte and emulate the access for these case,
it works not good:
- for the case 1, it may destroy the mapping established by other vcpu, and
do expensive instruction emulation.
- for the case 2, it may emulate the access even if the guest is accessing
the page which not used as page table. There is a example, 0~2M is used as
huge page in guest, in this huge page, only page 3 used as page table, then
guest read/writes on other pages can cause instruction emulation.
Both of these cases can be fixed by allowing guest to retry the access, it
will refault, then we can establish the mapping by using small page
Signed-off-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Acked-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
It is $(obj)/oid_registry.o that is dependent on $(obj)/oid_registry_data.c.
The object file cannot be built until $(obj)/oid_registry_data.c has been
generated.
A periodic and hard to reproduce parallel build failure is due to
this incorrect lib/Makefile dependency. The compile error is completely
disingenuous.
GEN lib/oid_registry_data.c
Compiling 49 OIDs
CC lib/oid_registry.o
gcc: error: lib/oid_registry.c: No such file or directory
gcc: fatal error: no input files
compilation terminated.
make[3]: *** [lib/oid_registry.o] Error 4
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: David Howells <dhowells@redhat.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Use of_match_ptr and add ifdef CONFIG_OF guard for regulator_gpio_of_match.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Don't adjust the selector in [get|set]_voltage_sel, fix it in list_voltage() instead.
For smps*(except smps10), the vsel reg-value and voltage mapping as below:
reg-value volt (uV) ( Assume RANGE is x1 )
0 0
1 500000
2 500000
3 500000
4 500000
5 500000
6 500000 (0.49V + 1 * 0.01V) * RANGE
7 510000 (0.49V + 2 * 0.01V) * RANGE
8 520000 (0.49V + 3 * 0.01V) * RANGE
9 530000 (0.49V + 4 * 0.01V) * RANGE
....
The linear mapping is start from selector 6.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Introduce a regulator_can_change_voltage() function for the subsytems or
drivers which might check if applying voltage change is possible and use
special workaround code when the driver is used with fixed regulators or
regulators with disabled ability to change the voltage.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
net/core/neighbour.c:65:12: warning: 'zero' defined but not used [-Wunused-variable]
net/core/neighbour.c:66:12: warning: 'unres_qlen_max' defined but not used [-Wunused-variable]
These variables are only used when CONFIG_SYSCTL is defined,
so move them under #ifdef CONFIG_SYSCTL.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Acked-by: Shan Wei <davidshan@tencent.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement ONE_REG interface for EPCR register adding KVM_REG_PPC_EPCR to
the list of ONE_REG PPC supported registers.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
[agraf: remove HV dependency, use get/put_user]
Signed-off-by: Alexander Graf <agraf@suse.de>
Add EPCR support in booke mtspr/mfspr emulation. EPCR register is defined only
for 64-bit and HV categories, we will expose it at this point only to 64-bit
virtual processors running on 64-bit HV hosts.
Define a reusable setter function for vcpu's EPCR.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
[agraf: move HV dependency in the code]
Signed-off-by: Alexander Graf <agraf@suse.de>
When delivering guest IRQs, update MSR computation mode according to guest
interrupt computation mode found in EPCR.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
[agraf: remove HV dependency in the code]
Signed-off-by: Alexander Graf <agraf@suse.de>
In BookE, EPCR is defined and valid when either the HV or the 64bit
category are implemented. Reflect this in the field definition.
Today the only KVM target on 64bit is HV enabled, so there is no
change in actual source code, but this keeps the code closer to the
spec and doesn't build up artificial road blocks for a PR KVM
on 64bit.
Signed-off-by: Alexander Graf <agraf@suse.de>
Extend MAS2 EPN mask to retain most significant bits on 64-bit hosts.
Use this mask in tlb effective address accessor.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Mask high 32 bits of MAS2's effective page number in tlbwe emulation for guests
running in 32-bit mode.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Mask high 32 bits of effective address in emulation layer for guests running
in 32-bit mode.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
[agraf: fix indent]
Signed-off-by: Alexander Graf <agraf@suse.de>
Add emulation helper for getting instruction ea and refactor tlb instruction
emulation to use it.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
[agraf: keep rt variable around]
Signed-off-by: Alexander Graf <agraf@suse.de>
Add interrupt handling support for 64-bit bookehv hosts. Unify 32 and 64 bit
implementations using a common stack layout and a common execution flow starting
from kvm_handler_common macro. Update documentation for 64-bit input register
values. This patch only address the bolted TLB miss exception handlers version.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
GET_VCPU define will not be implemented for 64-bit for performance reasons
so get rid of it also on 32-bit.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
64-bit GCC 4.5.1 warns about an uninitialized variable which was guarded
by a flag. Initialize the variable to make it happy.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
[agraf: reword comment]
Signed-off-by: Alexander Graf <agraf@suse.de>
Currently, if a machine check interrupt happens while we are in the
guest, we exit the guest and call the host's machine check handler,
which tends to cause the host to panic. Some machine checks can be
triggered by the guest; for example, if the guest creates two entries
in the SLB that map the same effective address, and then accesses that
effective address, the CPU will take a machine check interrupt.
To handle this better, when a machine check happens inside the guest,
we call a new function, kvmppc_realmode_machine_check(), while still in
real mode before exiting the guest. On POWER7, it handles the cases
that the guest can trigger, either by flushing and reloading the SLB,
or by flushing the TLB, and then it delivers the machine check interrupt
directly to the guest without going back to the host. On POWER7, the
OPAL firmware patches the machine check interrupt vector so that it
gets control first, and it leaves behind its analysis of the situation
in a structure pointed to by the opal_mc_evt field of the paca. The
kvmppc_realmode_machine_check() function looks at this, and if OPAL
reports that there was no error, or that it has handled the error, we
also go straight back to the guest with a machine check. We have to
deliver a machine check to the guest since the machine check interrupt
might have trashed valid values in SRR0/1.
If the machine check is one we can't handle in real mode, and one that
OPAL hasn't already handled, or on PPC970, we exit the guest and call
the host's machine check handler. We do this by jumping to the
machine_check_fwnmi label, rather than absolute address 0x200, because
we don't want to re-execute OPAL's handler on POWER7. On PPC970, the
two are equivalent because address 0x200 just contains a branch.
Then, if the host machine check handler decides that the system can
continue executing, kvmppc_handle_exit() delivers a machine check
interrupt to the guest -- once again to let the guest know that SRR0/1
have been modified.
Signed-off-by: Paul Mackerras <paulus@samba.org>
[agraf: fix checkpatch warnings]
Signed-off-by: Alexander Graf <agraf@suse.de>
When we change or remove a HPT (hashed page table) entry, we can do
either a global TLB invalidation (tlbie) that works across the whole
machine, or a local invalidation (tlbiel) that only affects this core.
Currently we do local invalidations if the VM has only one vcpu or if
the guest requests it with the H_LOCAL flag, though the guest Linux
kernel currently doesn't ever use H_LOCAL. Then, to cope with the
possibility that vcpus moving around to different physical cores might
expose stale TLB entries, there is some code in kvmppc_hv_entry to
flush the whole TLB of entries for this VM if either this vcpu is now
running on a different physical core from where it last ran, or if this
physical core last ran a different vcpu.
There are a number of problems on POWER7 with this as it stands:
- The TLB invalidation is done per thread, whereas it only needs to be
done per core, since the TLB is shared between the threads.
- With the possibility of the host paging out guest pages, the use of
H_LOCAL by an SMP guest is dangerous since the guest could possibly
retain and use a stale TLB entry pointing to a page that had been
removed from the guest.
- The TLB invalidations that we do when a vcpu moves from one physical
core to another are unnecessary in the case of an SMP guest that isn't
using H_LOCAL.
- The optimization of using local invalidations rather than global should
apply to guests with one virtual core, not just one vcpu.
(None of this applies on PPC970, since there we always have to
invalidate the whole TLB when entering and leaving the guest, and we
can't support paging out guest memory.)
To fix these problems and simplify the code, we now maintain a simple
cpumask of which cpus need to flush the TLB on entry to the guest.
(This is indexed by cpu, though we only ever use the bits for thread
0 of each core.) Whenever we do a local TLB invalidation, we set the
bits for every cpu except the bit for thread 0 of the core that we're
currently running on. Whenever we enter a guest, we test and clear the
bit for our core, and flush the TLB if it was set.
On initial startup of the VM, and when resetting the HPT, we set all the
bits in the need_tlb_flush cpumask, since any core could potentially have
stale TLB entries from the previous VM to use the same LPID, or the
previous contents of the HPT.
Then, we maintain a count of the number of online virtual cores, and use
that when deciding whether to use a local invalidation rather than the
number of online vcpus. The code to make that decision is extracted out
into a new function, global_invalidates(). For multi-core guests on
POWER7 (i.e. when we are using mmu notifiers), we now never do local
invalidations regardless of the H_LOCAL flag.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
The mask of MSR bits that get transferred from the guest MSR to the
shadow MSR included MSR_DE. In fact that bit only exists on Book 3E
processors, and it is assigned the same bit used for MSR_BE on Book 3S
processors. Since we already had MSR_BE in the mask, this just removes
MSR_DE.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This fixes various issues in how we were handling the VSX registers
that exist on POWER7 machines. First, we were running off the end
of the current->thread.fpr[] array. Ultimately this was because the
vcpu->arch.vsr[] array is sized to be able to store both the FP
registers and the extra VSX registers (i.e. 64 entries), but PR KVM
only uses it for the extra VSX registers (i.e. 32 entries).
Secondly, calling load_up_vsx() from C code is a really bad idea,
because it jumps to fast_exception_return at the end, rather than
returning with a blr instruction. This was causing it to jump off
to a random location with random register contents, since it was using
the largely uninitialized stack frame created by kvmppc_load_up_vsx.
In fact, it isn't necessary to call either __giveup_vsx or load_up_vsx,
since giveup_fpu and load_up_fpu handle the extra VSX registers as well
as the standard FP registers on machines with VSX. Also, since VSX
instructions can access the VMX registers and the FP registers as well
as the extra VSX registers, we have to load up the FP and VMX registers
before we can turn on the MSR_VSX bit for the guest. Conversely, if
we save away any of the VSX or FP registers, we have to turn off MSR_VSX
for the guest.
To handle all this, it is more convenient for a single call to
kvmppc_giveup_ext() to handle all the state saving that needs to be done,
so we make it take a set of MSR bits rather than just one, and the switch
statement becomes a series of if statements. Similarly kvmppc_handle_ext
needs to be able to load up more than one set of registers.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This adds basic emulation of the PURR and SPURR registers. We assume
we are emulating a single-threaded core, so these advance at the same
rate as the timebase. A Linux kernel running on a POWER7 expects to
be able to access these registers and is not prepared to handle a
program interrupt on accessing them.
This also adds a very minimal emulation of the DSCR (data stream
control register). Writes are ignored and reads return zero.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
