struct pcmcia_device *p_dev->conf.ConfigBase and .Present are set in almost
all PCMICA driver right at the beginning, using the same calls but slightly
different implementations. Unfiy this in the PCMCIA core.
Includes a small bugfix ("drivers/net/pcmcia/xirc2ps_cs.c: remove unused
label") from and Signed-off-by Adrian Bunk <bunk@stusta.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
As we read out the manufactor and card_id from the PCMCIA device in the
PCMCIA core, and device drivers can access those reliably in struct
pcmcia_device's fields manf_id and card_id, remove additional (and partly
broken) manf_id and card_id detection logic from PCMCIA device drivers.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Add IDs for Elan serial PCMCIA devices. In addition, move the
pdaudio_cf driver from matching based on manf_id and card_id to
the more specific prod_id1 and prod_id2 to avoid false
positives.
Signed-off-by: Tony Olech <tony.olech@elandigitalsystems.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Needed to support mpc52xx boards in arch/powerpc. This patch
retains the platform_bus support when compiling for arch/ppc,
but uses the of_platform bindings for arch/powerpc.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Single typo fix and whitespace changes. In preparation for heavy
changes to this driver when support for arch/powerpc is added.
Since the driver will be changing significantly anyway, then may
as well take the opportunity to clean it up first.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The below hunk was missed from the recent patch, and now, there are somewhat
inconsistent definitions:
in cpm_uart.h:
int __init cpm_uart_init_portdesc(void);
in cpm_uart_cpm1.c:
int __init cpm_uart_init_portdesc(void)
{
}
in cpm_uart_cpm2.c:
int cpm_uart_init_portdesc(void)
{
}
Signed-off-by: Kalle Pokki <kalle.pokki@iki.fi>
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The cpm_uart driver is initialised incorrectly, if there is a frame buffer
console, and CONFIG_SERIAL_CPM_CONSOLE is defined. The driver fails to
call cpm_uart_init_portdesc() and set_lineif() in this case.
Signed-off-by: Kalle Pokki <kalle.pokki@iki.fi>
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The SMC and SCC hardware transmitter is enabled at the wrong
place. Simply writing twice to the non-console port, like
$ echo asdf > /dev/ttyCPM1
$ echo asdf > /dev/ttyCPM1
puts the shell into endless uninterruptible sleep, since the
transmitter is stopped after the first write, and is not enabled
before the shutdown function of the second write. Thus the transmit
buffers are never emptied.
Signed-off-by: Kalle Pokki <kalle.pokki@iki.fi>
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix typo (repeated) in serial Kconfig.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The SGI PCI-RT card, based on the SGI IOC4 chip, will be made available on
Altix XE (x86_64) platforms in the near future. As such it is now a
misnomer for the IOC4 base device driver to live under drivers/sn, and
would complicate builds for non-SN2.
This patch moves the IOC4 base driver code from drivers/sn to drivers/misc,
and updates the associated Makefiles and Kconfig files to allow building on
non-SN2 configs. Due to the resulting change in link order, it is now
necessary to use late_initcall() for IOC4 subdriver initialization.
[akpm@osdl.org: __udivdi3 fix]
[akpm@osdl.org: fix default in Kconfig]
Acked-by: Pat Gefre <pfg@sgi.com>
Acked-by: Jeremy Higdon <jeremy@sgi.com>
Signed-off-by: Brent Casavant <bcasavan@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix this 2.6.19-rc1 build warnings from modpost:
WARNING: vmlinux - Section mismatch: reference to .init.text:sunzilog_console_setup from .data between 'sunzilog_console' (at offset 0x8394) and 'devices_subsys'
Signed-off-by: Martin Habets <errandir_news@mph.eclipse.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Eliminate casts to/from void*
- Eliminate checks for conditions that never occur. These typically
fall into two classes:
1) Checking for 'dev_id == NULL', then it is never called with
NULL as an argument.
2) Checking for invalid irq number, when the only caller (the
system) guarantees the irq handler is called with the proper
'irq' number argument.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
The atmel_console_get_options() function initializes the baud,
parity and bits settings from the actual hardware setup, in
case it has been initialized by a e.g. boot loader.
The baud rate, however, is not necessarily exactly equal to one of
the standard baud rates (115200, etc.) This means that the baud rate
calculated by this function may be slightly higher or slightly lower
than one of the standard baud rates.
If the baud rate is slightly lower than the target, this causes
problems when uart_set_option() tries to match the detected baud rate
against the standard baud rate, as it will always select a baud rate
that is lower or equal to the target rate. For example if the
detected baud rate is slightly lower than 115200, usart_set_options()
will select 57600.
This patch fixes the problem by subtracting 1 from the value in BRGR
when calculating the baud rate. The detected baud rate will thus
always be higher than the nearest standard baud rate, and
uart_set_options() will end up doing the right thing.
Tested on ATSTK1000 and AT91RM9200-EK boards. Both are broken without
this patch.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make CONFIG_SERIAL_ATMEL selectable on AVR32 and #ifdef out some ARM-
specific code in the driver.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In order to initialize the serial console early, the atmel_serial
driver had to do a hack where it compared the physical address of the
port with an address known to be permanently mapped, and used it as a
virtual address. This got around the limitation that ioremap() isn't
always available when the console is being initalized.
This patch removes that hack and replaces it with a new "regs" field
in struct atmel_uart_data that the board-specific code can initialize
to a fixed virtual mapping for platform devices where this is possible.
It also initializes the DBGU's regs field with the address the driver
used to check against.
On AVR32, the "regs" field is initialized from the physical base
address when this it can be accessed through a permanently 1:1 mapped
segment, i.e. the P4 segment.
If regs is NULL, the console initialization is delayed until the "real"
driver is up and running and ioremap() can be used.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Rename at91_register_uart_fns and associated structs and variables
to make it consistent with the atmel_ prefix used by the rest of
the driver.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The at91_serial driver can be used with both AT32 and AT91 devices
from Atmel and has therefore been renamed atmel_serial. The only
thing left is to rename PORT_AT91 PORT_ATMEL.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Prefix all internal functions and variables with atmel_ instead of
at91_.
The at91_register_uart_fns() stuff is left as is since I can't find
any actual users of it.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move include/asm/arch/at91rm9200_usart.h into drivers/serial and rename
it atmel_usart.h. Also delete AVR32's version of this file.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davej/configh:
Remove all inclusions of <linux/config.h>
Manually resolved trivial path conflicts due to removed files in
the sound/oss/ subdirectory.
Russell King pointed out that asm/serial.h is anachronistic and we were
misusing BASE_BAUD. So fix BASE_BAUD for PCI 16550 UARTs, move LASI_BASE_BAUD
into 8250_gsc, and fix the obsolete comment about reserving serial port slots.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Many files include the filename at the beginning, serveral used a wrong one.
Signed-off-by: Uwe Zeisberger <Uwe_Zeisberger@digi.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (29 commits)
[POWERPC] Fix rheap alignment problem
[POWERPC] Use check_legacy_ioport() for ISAPnP
[POWERPC] Avoid NULL pointer in gpio1_interrupt
[POWERPC] Enable generic rtc hook for the MPC8349 mITX
[POWERPC] Add powerpc get/set_rtc_time interface to new generic rtc class
[POWERPC] Create a "wrapper" script and use it in arch/powerpc/boot
[POWERPC] fix spin lock nesting in hvc_iseries
[POWERPC] EEH failure to mark pci slot as frozen.
[POWERPC] update powerpc defconfig files after libata kconfig breakage
[POWERPC] enable sysrq in pmac32_defconfig
[POWERPC] UPIO_TSI cleanup
[POWERPC] rewrite mkprep and mkbugboot in sane C
[POWERPC] maple/pci iomem annotations
[POWERPC] powerpc oprofile __user annotations
[POWERPC] cell spufs iomem annotations
[POWERPC] NULL noise removal: spufs
[POWERPC] ppc math-emu needs -fno-builtin-fabs for math.c and fabs.c
[POWERPC] update mpc8349_itx_defconfig and remove some debug settings
[POWERPC] Always call cede in pseries dedicated idle loop
[POWERPC] Fix loop logic in irq_alloc_virt()
...
As part of an SMP cleanliness pass over UML, I consted a bunch of
structures in order to not have to document their locking. One of these
structures was a struct tty_operations. In order to const it in UML
without introducing compiler complaints, the declaration of
tty_set_operations needs to be changed, and then all of its callers need to
be fixed.
This patch declares all struct tty_operations in the tree as const. In all
cases, they are static and used only as input to tty_set_operations. As an
extra check, I ran an i386 allyesconfig build which produced no extra
warnings.
53 drivers are affected. I checked the history of a bunch of them, and in
most cases, there have been only a handful of maintenance changes in the
last six months. serial_core.c was the busiest one that I looked at.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The Compaq TC1000 and Fujitsu Stylistic range of tablet machines use
touchscreens from FPI. These are implemented as serial interfaces,
generally exposed in the ACPIPNP information on the system. This patch
adds them to the 8250_pnp driver tables, avoiding the need to mess
around with setserial to set them up.
I haven't been able to confirm what FUJ02B5, FUJ02BA and FUJ02BB are.
FUJ02B1 refers to the controller for the system hotkeys. FUJ02BC appears
to be the last in the range - after this, they moved to Wacom-based
systems.
Signed-off-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Serial is _slow_ sometimes. So slow, that the NMI watchdog kicks in.
NMI Watchdog detected LOCKUP on CPU2CPU 2
Modules linked in: loop usb_storage md5 ipv6 parport_pc lp parport autofs4 i2c_dev i2c_core rfcomm l2cap bluetooth sunrpc pcdPid: 3138, comm: gpm Not tainted 2.6.11-1.1290_FC4smp
RIP: 0010:[<ffffffff80273b8a>] <ffffffff80273b8a>{serial_in+106}
RSP: 0018:ffff81003afc3d50 EFLAGS: 00000002
RAX: 0000000000000020 RBX: 0000000000000020 RCX: 0000000000000000
RDX: 00000000000003fd RSI: 0000000000000005 RDI: ffffffff804dcd60
RBP: 00000000000024fc R08: 000000000000000a R09: 0000000000000033
R10: ffff81001beb7c20 R11: 0000000000000020 R12: ffffffff804dcd60
R13: ffffffff804ade76 R14: 000000000000002b R15: 000000000000002c
FS: 00002aaaaaac4920(0000) GS:ffffffff804fca00(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 00002aaaaabcb000 CR3: 000000003c0d0000 CR4: 00000000000006e0
Process gpm (pid: 3138, threadinfo ffff81003afc2000, task ffff81003eb63780)
Stack: ffffffff80275f2e 0000000000000000 ffffffff80448380 0000000000007d6b
000000000000002c fffffffffffffbbf 0000000000000292 0000000000008000
ffffffff80138e8c 0000000000007d97
Call Trace:<ffffffff80275f2e>{serial8250_console_write+270} <ffffffff80138e8c>{__call_console_drivers+76}
<ffffffff8013914b>{release_console_sem+315} <ffffffff80260325>{con_open+149}
<ffffffff80254e99>{tty_open+537} <ffffffff80192713>{chrdev_open+387}
<ffffffff80188824>{dentry_open+260} <ffffffff80188994>{filp_open+68}
<ffffffff80187b73>{get_unused_fd+227} <ffffffff80188a6c>{sys_open+76}
<ffffffff8010ebc6>{tracesys+209}
Code: 0f b6 c0 c3 66 90 41 57 49 89 f7 41 56 41 be 00 01 00 00 41
console shuts up ...
I initially did the patch below a year ago for the Fedora kernel, and have
been keeping it up to date since. I recently got the same thing happening
on a vanilla kernel, so figured it was time to repost this.
Signed-off-by: Dave Jones <davej@redhat.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A serial card might have been removed when the system is resumed.
This results in a suspended port being shut down, which results in
the ports shutdown method being called twice in a row. This causes
BUGs. Avoid this by tracking the suspended state separately from
the initialised state.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Unfortunately, pcmcia_dev_present() returns false when a device is
suspended, so checking this on resume does not work too well. Omit
this test.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove some code which is unneeded if CONFIG_PM=n.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The patch below is necessary for 115200 baud on an OMAP1510 internal UART.
It's been in the linux-omap tree for some time and with it applied to a
vanilla Linus git tree the serial console on the Amstrad Delta (which is
OMAP1510 based and whose initial bootloader runs at 115200) works fine (it
doesn't without it).
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix the issue of returning 0 even in case of error from uart_set_info
function. Now it returns the error EBUSY when it can not set new port.
Signed-off-by: Ram Gupta <r.gupta@astronautics.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
