Bunch more fixes for 4.3, most of it skl fallout. It's not quite all yet,
there's still a few more patches pending to enable DDI-E correctly on skl.
Also included the dpms atomic work from Maarten since atomic is just a
pain and not including would cause piles of conflicts right from the
start.
* tag 'drm-intel-next-fixes-2015-08-16' of git://anongit.freedesktop.org/drm-intel: (67 commits)
drm/i915: Per-DDI I_boost override
drm/i915/skl: WaIgnoreDDIAStrap is forever, always init DDI A
drm/i915: fix checksum write for automated test reply
drm/i915: Contain the WA_REG macro
drm/i915: Remove the failed context from the fpriv->context_idr
drm/i915: Report IOMMU enabled status for GPU hangs
drm/i915: Check idle to active before processing CSQ
drm/i915: Set alternate aux for DDI-E
drm/i915: Set power domain for DDI-E
drm/i915: fix stolen bios_reserved checks
drm/i915: Use masked write for Context Status Buffer Pointer
drm/i915/skl WaDisableSbeCacheDispatchPortSharing
drm/i915: Spam less on dp aux send/receive problems
drm/i915: Handle return value in intel_pin_and_fence_fb_obj, v2.
drm/i915: Only update mode related state if a modeset happened.
drm/i915: Remove connectors_active.
drm/i915: Remove connectors_active from intel_dp.c, v2.
drm/i915: Remove connectors_active from sanitization, v2.
drm/i915: Get rid of dpms handling.
drm/i915: Make crtc checking use the atomic state, v2.
...
An OEM may request increased I_boost beyond the recommended values
by specifying an I_boost value to be applied to all swing entries for
a port. These override values are specified in VBT.
v2: rebase and remove unused iboost_bit variable
Issue: VIZ-5676
Signed-off-by: Antti Koskipaa <antti.koskipaa@linux.intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Backmerge drm-intel-fixes because a bunch of atomic patch backporting
we had to do lead to horrible conflicts.
Conflicts:
drivers/gpu/drm/drm_crtc.c
Just a bit of context conflict between -next and -fixes.
drivers/gpu/drm/i915/intel_atomic.c
drivers/gpu/drm/i915/intel_display.c
Atomic conflicts, always pick the code from -next.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
There is currently conflicting documentation on which steppings the
workaround is needed, up to C vs. forever. However there is post-C
stepping hardware that doesn't report port presence on DDI A, leading to
black screen on eDP. Assume the strap isn't connected, and try to enable
DDI A on these machines. (We'll still check the VBT for the info in DDI
init.)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Mika Westerberg <mika.westerberg@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
DP spec requires the checksum of the last block read to be written
when replying to TEST_EDID_READ. This patch fixes the current code
to do the same.
v2: removed loop for jumping blocks and performed direct addition
as recommended by Daniel
Signed-off-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Prevent leaking the if scoping by containing the WA_REG
macro inside its own scope.
Reported-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
[danvet: Appease checkpatch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we encounter an allocation failure during ppggt creation (trivial
even with 16Gib+ RAM!), we need to remove the dead context from the
fpriv->context_idr along with the references.
gem_exec_ctx: page allocation failure: order:0, mode:0x8004
CPU: 3 PID: 27272 Comm: gem_exec_ctx Tainted: G W 4.2.0-rc5+ #37
0000000000000000 ffff880086ff7a78 ffffffff816b947a ffff88041ed90038
0000000000008004 ffff880086ff7b08 ffffffff8114b1a5 ffff880086ff7ac8
ffffffff8108d848 0000000000000000 ffffffff81ce84b8 0000000000000000
Call Trace:
[<ffffffff816b947a>] dump_stack+0x45/0x57
[<ffffffff8114b1a5>] warn_alloc_failed+0xd5/0x120
[<ffffffff8108d848>] ? __wake_up+0x48/0x60
[<ffffffff8114e0ed>] __alloc_pages_nodemask+0x73d/0x8e0
[<ffffffffc0472238>] ? i915_gem_execbuffer2+0x148/0x240 [i915]
[<ffffffffc0474240>] __setup_page_dma+0x30/0x110 [i915]
[<ffffffffc0477f61>] gen8_ppgtt_init+0x31/0x2f0 [i915]
[<ffffffffc04785e0>] i915_ppgtt_init+0x30/0x80 [i915]
[<ffffffffc0478928>] i915_ppgtt_create+0x48/0xc0 [i915]
[<ffffffffc046c9c2>] i915_gem_create_context+0x1c2/0x390 [i915]
[<ffffffffc046d9cb>] i915_gem_context_create_ioctl+0x5b/0xa0 [i915]
leading to an oops in i915_gem_context_close. Also note that this
benchmark should not be running out of memory in the first place...
Testcase: igt/benchmark/gem_exec_ctx -b create # ppgtt >= 2
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The IOMMU for Intel graphics has historically had many issues resulting
in random GPU hangs. Lets include its status when capturing the GPU hang
error state for post-mortem analysis.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If idle to active bit is set, the rest of the fields
in CSQ are not valid.
Bail out early if this is the case in order to prevent
rest of the loop inspecting stale values.
This was found by Bspec/code inspection. Doesn't seem to fix any of
the known issues.
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Arun Siluvery <arun.siluvery@linux.intel.com>
[danvet: Add note about how this was found.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is no correspondent Aux channel for DDI-E.
So we need to rely on VBT to let us know witch one
is being used instead.
v2: Removing some trailing spaces and giving proper
credit to Xiong that added a nice way to avoid port
conflicts by setting supports_dp = 0 when using
equivalent aux for DDI-E.
Credits-to: Xiong Zhang <xiong.y.zhang@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Xiong Zhang <xiong.y.zhang@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I started digging this when I noticed that the BDW code was just
reserving 1mb by coincidence since it was reading reserved fields.
Then I noticed we didn't have any values set for SNB and earlier, and
that the HSW sizes were wrong. After that, I noticed that the reserved
area has a specific start, and may not exactly end where the stolen
memory ends. I also noticed the base pointer can be zero. So I decided
to just write a single patch fixing everything instead of 20 patches
that would be much harder to review.
This patch may solve random stolen memory corruption/problems on
almost all platforms. Notice that since this is always dealing with
the top of the stolen memory, the problems are not so easy to
reproduce - especially since FBC is still disabled by default.
One of the major differences of this patch is that we now look at both
the size and base address. By only looking at the size we were
assuming that the reserved area was always at the very top of
stolen, which is not always true.
After we merge the patch series that allows user space to allocate
stolen memory we'll be able to write IGT tests that maybe catch the
bugs fixed by this patch.
v2:
- s/BIOS reserved/stolen reserved/g (Chris)
- Don't DRM_ERROR if we can't do anything about it (Chris)
- Improve debug messages (Chris).
- Use the gen7 version instead of gen6 on HSW. Tom found some
documentation problems, so I think with gen7 we're on the safer
side (Tom).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This register needs to be updated with masked writes.
This was found by code inspection and comparison with Bspec and
doesn't seem to fix any known issue.
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
[danvet: Add note about impact.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we encounter frequent problems with dp aux channel
communications, we end up spamming the dmesg with the
exact similar trace and status.
Inject a new backtrace only if we have new information
to share as otherwise we flush out all other important
stuff.
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-EDEADLK has special meaning in atomic, but get_fence may call
i915_find_fence_reg which can return -EDEADLK.
This has special meaning in the atomic world, so convert the error
to -EBUSY for this case.
Changes since v1:
- Add comment in the code.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The rest will be a noop anyway, since without modeset there will be
no updated dplls and no modeset state to update.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There are no more users, byebye!
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that everything's atomic, checking encoder->base.crtc is enough.
This function doesn't have the locks to dereference crtc->state, but
stealing an encoder bound to any crtc is probably enough reason to warn.
Changes since v1:
- Commit message.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
connectors_active will be removed, so just calculate this instead.
Changes since v1:
- Look for the right pointer in intel_sanitize_encoder.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is now done completely atomically.
Keep connectors_active for now, but make it mirror crtc_state->active.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of allocating pipe_config on the stack use the old
crtc_state, it's only going to freed from this point on.
All crtc' are now only checked once during modeset,
because false positives can happen with encoders after
dpms changes and to limit the amount of errors for 1 failure.
Changes since v1:
- crtc_state -> old_crtc_state
- state -> old_state
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Connectors are updated atomically now, so the only interaction
with the encoder is through base.crtc.
If it's NULL the encoder's not part of any crtc, and if it's
not NULL then active should be equal to crtc_state->active.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is handled by the atomic core now, no need to check this for ourself.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Right now dpms callbacks can still fiddle with the connector state,
but it can only turn connectors off.
This is remediated by only checking crtc->state->active when the
connector is active, and ignore crtc->state->active when the
connector is off.
connectors_active is no longer checked, and will be removed later
in this series together with dpms.
Another check for !encoder->crtc is performed by check_encoder_state
too, so it can be removed.
Changes since v1:
- Add commit message.
- rename state to old_state.
- Move deletion of mst_port check to mst patch.
Changes since v2:
- Fix a null pointer dereference on MST now hw readout is fixed.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fully remove the MST connector from the atomic state, and remove the
early returns in check_*_state for MST connectors.
With atomic the state can be made consistent all the time.
Thanks to Sivakumar Thulasimani for the idea of using
drm_atomic_helper_set_config.
Changes since v1:
- Remove the MST check in intel_connector_check_state too.
Changes since v2:
- Use drm_atomic_helper_set_config.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
First step in removing dpms and validating atomic state.
There can still be a mismatch in the connector state because the dpms
callbacks are still used, but this can not happen immediately after a modeset.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Set connectors_changed to force a modeset if the panel fitter's force
enabled on eDP.
Changes since v1:
- Use connectors_changed instead of active_changed because it's a
routing update.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch is based on the upstream commit 5ac1c4bcf0 and amended
for v4.2 to make sure it works as intended.
Repeated calls to begin_crtc_commit can cause warnings like this:
[ 169.127746] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:616
[ 169.127835] in_atomic(): 0, irqs_disabled(): 1, pid: 1947, name: kms_flip
[ 169.127840] 3 locks held by kms_flip/1947:
[ 169.127843] #0: (&dev->mode_config.mutex){+.+.+.}, at: [<ffffffff814774bc>] __drm_modeset_lock_all+0x9c/0x130
[ 169.127860] #1: (crtc_ww_class_acquire){+.+.+.}, at: [<ffffffff814774cd>] __drm_modeset_lock_all+0xad/0x130
[ 169.127870] #2: (crtc_ww_class_mutex){+.+.+.}, at: [<ffffffff81477178>] drm_modeset_lock+0x38/0x110
[ 169.127879] irq event stamp: 665690
[ 169.127882] hardirqs last enabled at (665689): [<ffffffff817ffdb5>] _raw_spin_unlock_irqrestore+0x55/0x70
[ 169.127889] hardirqs last disabled at (665690): [<ffffffffc0197a23>] intel_pipe_update_start+0x113/0x5c0 [i915]
[ 169.127936] softirqs last enabled at (665470): [<ffffffff8108a766>] __do_softirq+0x236/0x650
[ 169.127942] softirqs last disabled at (665465): [<ffffffff8108ae75>] irq_exit+0xc5/0xd0
[ 169.127951] CPU: 1 PID: 1947 Comm: kms_flip Not tainted 4.1.0-rc4-patser+ #4039
[ 169.127954] Hardware name: LENOVO 2349AV8/2349AV8, BIOS G1ETA5WW (2.65 ) 04/15/2014
[ 169.127957] ffff8800c49036f0 ffff8800cde5fa28 ffffffff817f6907 0000000080000001
[ 169.127964] 0000000000000000 ffff8800cde5fa58 ffffffff810aebed 0000000000000046
[ 169.127970] ffffffff81c5d518 0000000000000268 0000000000000000 ffff8800cde5fa88
[ 169.127981] Call Trace:
[ 169.127992] [<ffffffff817f6907>] dump_stack+0x4f/0x7b
[ 169.128001] [<ffffffff810aebed>] ___might_sleep+0x16d/0x270
[ 169.128008] [<ffffffff810aed38>] __might_sleep+0x48/0x90
[ 169.128017] [<ffffffff817fc359>] mutex_lock_nested+0x29/0x410
[ 169.128073] [<ffffffffc01635f0>] ? vgpu_write64+0x220/0x220 [i915]
[ 169.128138] [<ffffffffc017fddf>] ? ironlake_update_primary_plane+0x2ff/0x410 [i915]
[ 169.128198] [<ffffffffc0190e75>] intel_frontbuffer_flush+0x25/0x70 [i915]
[ 169.128253] [<ffffffffc01831ac>] intel_finish_crtc_commit+0x4c/0x180 [i915]
[ 169.128279] [<ffffffffc00784ac>] drm_atomic_helper_commit_planes+0x12c/0x240 [drm_kms_helper]
[ 169.128338] [<ffffffffc0184264>] __intel_set_mode+0x684/0x830 [i915]
[ 169.128378] [<ffffffffc018a84a>] intel_crtc_set_config+0x49a/0x620 [i915]
[ 169.128385] [<ffffffff817fdd39>] ? mutex_unlock+0x9/0x10
[ 169.128391] [<ffffffff81467b69>] drm_mode_set_config_internal+0x69/0x120
[ 169.128398] [<ffffffff8119b547>] ? might_fault+0x57/0xb0
[ 169.128403] [<ffffffff8146bf93>] drm_mode_setcrtc+0x253/0x620
[ 169.128409] [<ffffffff8145c600>] drm_ioctl+0x1a0/0x6a0
[ 169.128415] [<ffffffff810b3b41>] ? get_parent_ip+0x11/0x50
[ 169.128424] [<ffffffff811e9ab8>] do_vfs_ioctl+0x2f8/0x530
[ 169.128429] [<ffffffff810d0fcd>] ? trace_hardirqs_on+0xd/0x10
[ 169.128435] [<ffffffff812e7676>] ? selinux_file_ioctl+0x56/0x100
[ 169.128439] [<ffffffff811e9d71>] SyS_ioctl+0x81/0xa0
[ 169.128445] [<ffffffff81800697>] system_call_fastpath+0x12/0x6f
Solve it by using the newly introduced drm_atomic_helper_commit_planes_on_crtc.
The problem here was that the drm_atomic_helper_commit_planes() helper
we were using was basically designed to do
begin_crtc_commit(crtc #1)
begin_crtc_commit(crtc #2)
...
commit all planes
finish_crtc_commit(crtc #1)
finish_crtc_commit(crtc #2)
The problem here is that since our hardware relies on vblank evasion,
our CRTC 'begin' function waits until we're out of the danger zone in
which register writes might wind up straddling the vblank, then disables
interrupts; our 'finish' function re-enables interrupts after the
registers have been written. The expectation is that the operations between
'begin' and 'end' must be performed without sleeping (since interrupts
are disabled) and should happen as quickly as possible. By clumping all
of the 'begin' calls together, we introducing a couple problems:
* Subsequent 'begin' invocations might sleep (which is illegal)
* The first 'begin' ensured that we were far enough from the vblank that
we could write our registers safely and ensure they all fell within
the same frame. Adding extra delay waiting for subsequent CRTC's
wasn't accounted for and could put us back into the 'danger zone' for
CRTC #1.
This commit solves the problem by using a new helper that allows an
order of operations like:
for each crtc {
begin_crtc_commit(crtc) // sleep (maybe), then disable interrupts
commit planes for this specific CRTC
end_crtc_commit(crtc) // reenable interrupts
}
so that sleeps will only be performed while interrupts are enabled and
we can be sure that registers for a CRTC will be written immediately
once we know we're in the safe zone.
The crtc->config->base.crtc update may seem unrelated, but the helper
will use it to obtain the crtc for the state. Without the update it
will dereference NULL and crash.
Changes since v1:
- Use Matt Roper's commit message.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
References: https://bugs.freedesktop.org/show_bug.cgi?id=90398
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This should be much cleaner, with the same effects.
(cherry picked for v4.2 from commit fb9d6cf8c2)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
References: https://bugs.freedesktop.org/show_bug.cgi?id=90398
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
In
commit d328c9d78d
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Apr 10 16:22:37 2015 +0200
drm/i915: Select starting pipe bpp irrespective or the primary plane
we started to select the pipe bpp from sink capabilities and not from
the primary framebuffer - that one might change (and we don't want to
incur a modeset) and sprites might contain higher bpp content too.
We also selected dithering on a 8 bpc screen displaying a 24bpp rgb
primary, because pipe_bpp is 24 for such a typical 8 bpc sink, but since
the commit mentioned above, base_bpp is always the absolute maximum
supported by the hardware, e.g., 36 bpp on my Ironlake chip. Iow. the
only way to not get dithering would have been to connect a deep color 12
bpc display, so pipe_bpp == 36 == base_bpp.
Hence only enable dithering on 6bpc screens where we difinitely and
always want it.
Cc: Mario Kleiner <mario.kleiner.de@gmail.com>
Reported-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-and-tested-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Rather than a mix of the the sized uint32_t and signed integer, use an
unsized unsigned int to specify the format count.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of our own duplicated one. This fixes a bug in the driver
unload code if DRM_FBDEV_EMULATION=n but DRM_I915_FBDEV=y because we
try to unregister the nonexistent fbdev drm_framebuffer.
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reported-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull drm fixes from Daniel Vetter:
"One i915 regression fix and a drm core one since Dave's not around,
both introduced in 4.2 so not cc: stable.
The fix for the warning Ted reported isn't in here yet since he didn't
yet supply a tested-by and I can't repro this one myself (it's in
fixup code that needs firmware doing something i915 wouldn't do)"
* tag 'drm-intel-fixes-2015-08-07' of git://anongit.freedesktop.org/drm-intel:
drm/vblank: Use u32 consistently for vblank counters
drm/i915: Allow parsing of variable size child device entries from VBT
VBT version 196 increased the size of common_child_dev_config. The parser
code assumed that the size of this structure would not change.
The modified code now copies the amount needed based on the VBT version,
and emits a debug message if the VBT version is unknown (too new);
since the struct config block won't shrink in newer versions it should
be harmless to copy the maximum known size in such cases, so that's
what we do, but emitting the warning is probably sensible anyway.
In the longer run it might make sense to modify the parser code to
use a version/feature mapping, rather than hardcoding things like this,
but for now the variants are fairly managable.
This fixes a regression introduced in
commit 90e4f1592b
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Wed Mar 25 18:45:58 2015 +0200
drm/i915: Fix the VBT child device parsing for BSW
since we're hitting a DRM_ERROR on older platforms with this.
v2: Stricter size checks
Signed-off-by: David Weinehall <david.weinehall@linux.intel.com>
[danvet: Fixup format string.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need a few core drm patches to be able to merge Maarten's series to
convert DPMS over to atomic.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Use the newly created wrapper drm_fb_helper functions instead of calling
core fbdev functions directly. They also simplify the fb_info creation.
v3:
- Don't touch remove_conflicting_framebuffers
v2:
- No changes
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Trying to do anything with kms drivers when oopsing has become a
failing proposition. But since we can end up in the fbdev code simply
due to the console unblanking that's done unconditionally just
removing our panic handler isn't enough. We need to block all fbdev
callbacks when oopsing.
There was already one in the blank handler, but it failed silently.
That makes it impossible for drivers (like i915) who subclass these
functions to figure this out.
Instead consistently return -EBUSY so that everyone knows that we
really don't want to be bothered right now. This also allows us to
remove a pile of FIXMEs from the i915 fbdev code (since due to the
failure code they now won't attempt to grab dangerous locks any more).
Cc: Dave Airlie <airlied@gmail.com>
Cc: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Looks like
commit eddfcbcdc2
Author: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Date: Mon Jun 15 12:33:53 2015 +0200
drm/i915: Update less state during modeset.
introduced the unconditional calling of disable_shared_dpll, but didn't
fix up pre-gen5 to avoid the BUG_ON at the top of the function.
So change the BUG_ON into a gen check (alternately we could move the
BUG_ON until later, since we shouldn't have a pll struct here either,
but this seems clearer to read).
This fixes a crash on load on my x200s platform.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch contains the changes to remove the byte
swapping logic introduced with old dmc firmware.
While debugging PC10 entry issue for skylake found
with latest dmc firmware version 1.18 without byte
swapping dmc is working fine and able to enter PC10.
Note that apparently this was changed with dmc version 1.0 and earlier
ones indeed are byteswapped like this ...
v1: Initial version.
v2: Corrected firmware size during memcpy(). (Suggested by Sunil)
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Vathsala Nagaraju <vathsala.nagaraju@intel.com>
Reviewed-by: A.Sunil Kamath <sunil.kamath@intel.com>
[danvet: Add note that this only holds for released dmc firmware.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BPP bits defined in VBT should be used only on panels whose
edid version is 1.3 or older. EDID version 1.4 introduced offsets
where bpp is defined and read into display_info, hence bpp from
VBT will be used only when bpc in display_info is zero.
v2: use display_info.bpc for deciding when to use vbt_bpp (Jani)
Signed-off-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I was told that the "repurposed D1 definition" is still valid for SKL.
It is BDW that is special due to its hotplug bug, so let's
special-case BDW instead of HSW.
Cc: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Similar to the ->enable vfunc in patch "drm/i915: Extract a
intel_power_well_enable() function".
v2 (from Paulo):
- Same s/i915_/intel_/ bikeshed as the previous patch.
- Update the commit hash.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need a bit book keeping around power wells' ops->enable(), namely a
nice debug message and updating hw_enabled. Let's introduce a
intel_power_well_enable() function to make sure all the callers do the
same things.
v2 (from Paulo):
- s/i915_power_well_enable/intel_power_well_enable/ since everything
else on this file uses intel_ instead of i915_.
- Fix typo in commit message.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With this simple git diff command one can see that skl_init_workarounds()
got two copies of WaBarrierPerformanceFixDisable:skl:
git diff -U21 ca6e4405779e^1 ca6e440577 drivers/gpu/drm/i915/intel_ringbuffer.c
This happened when the backmerge of drm-intel-fixes-2015-07-15
Merged the same fix on both sides. Same fix but not identical enough for
git: with a different surrounding context; hence the code duplication.
This commit merely reverts the output of the git command above
= the duplication introduced in the backmerge.
(This duplication was found while running git sanity checks on a
_linearized_ i915 forklift for ChromeOS.)
Signed-off-by: Marc Herbert <marc.herbert@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since active function on VLV immediately activate PSR let's give more
time for idleness. Different from core platforms where we have idle_frames
count.
Also kms_psr_sink_crc now is automated and always get this:
[drm:intel_enable_pipe] enabling pipe A
[drm:intel_edp_backlight_on]
[drm:intel_panel_enable_backlight] pipe
[drm:intel_panel_enable_backlight] pipe A
[drm:intel_panel_actually_set_backlight] set backlight PWM = 7812
PSR gets enabled somewhere here after backlight.
[drm:intel_get_hpd_pins] hotplug event received, stat 0x00000000, dig 0x0
[drm:vlv_pipe_set_fifo_size] Pipe A FIFO split 511 / 511 / 511
[drm:vlv_update_wm] Setting FIFO watermarks - A: plane=391, cursor=63, sp
PSR gets flushed around here by intel_atomic_commit
[drm:vlv_pipe_set_fifo_size] Pipe A FIFO split 511 / 511 / 511
[drm:vlv_update_wm] Setting FIFO watermarks - A: plane=391, cursor=63, sp
[drm:intel_set_memory_cxsr] memory self-refresh is enabled
[drm:intel_connector_check_state] [CONNECTOR:39:eDP-1]
[drm:check_encoder_state] [ENCODER:30:DAC-30]
[drm:check_encoder_state] [ENCODER:31:TMDS-31]
[drm:check_encoder_state] [ENCODER:36:TMDS-36]
[drm:check_encoder_state] [ENCODER:38:TMDS-38]
[drm:check_crtc_state] [CRTC:21]
[drm:check_crtc_state] [CRTC:26]
[drm:intel_psr_activate [i915]] *ERROR* PSR Active
[drm:intel_get_hpd_pins] hotplug event received, stat 0x00000000, dig 0x
[drm:intel_set_cpu_fifo_underrun_reporting [i915]] *ERROR* pipe A underrun
[drm:intel_cpu_fifo_underrun_irq_handler [i915]] *ERROR* CPU pipe A FIFO
Underrun.
It is true that in a product we won't keep disabling and enabling planes so
frequently, but for safeness let's stay conservative.
It is also true that 500ms is an etternity. But PSR is anyway a power saving
feature for idle scenario. So if it is idle feature stays on and 500ms to get
it reanabled is not that insane.
v2: Rebase over intel_psr.c and fix typo.
v3: Revival: Manual tests indicated that this is needed. With a short delay
there is a huge risk of getting blank screens when planes are being enabled.
v4: Revival 2 with reasonable delay. 1/2 sec instead of 5. VBT is 10 sec but
actually time for link training what we aren't doing, but with only 100 sec
in some cases kms_psr_sink_crc manual was showing blank screen,
so let's use this for now. Also changed comment by a FIXME.
v5: Rebase after a long time, remove FIXME and update comment above.
v6: msecs_to_jiffies is already on delay. remove duplication.
v7: use msecs_to_jiffies on schedule_delayed_work call.
Reviewed-by: Durgadoss R <durgadoss.r@intel.com> (v4)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Tested-By: Intel Graphics QA PRTS (Patch Regression Test System Contact: shuang.he@intel.com)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is just a preparation patch to make clear what operation we
are performing. There is no functional change on the sink crc
logic.
hsw_disable_ips has been moved a bit further in the start function
to avoid disabling ips when sink crc is not going to be started.
and to avoid goto on this function.
v2: explain why hsw_disable_ips() call place has changed.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Rafael Antognolli <rafael.antognolli@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
First, an introduction. We currently have two types of GTT mmaps: the
"normal" old mmap, and the WC mmap. For frontbuffer-related features
that have automatic hardware tracking, only the non-WC mmap writes are
detected by the hardware. Since inside the Kernel both are treated as
ORIGIN_GTT, any features ignoring ORIGIN_GTT because of the hardware
tracking are destined to fail.
One of the special rules defined for the WC mmaps is that the user
should call the dirtyfb IOCTL after he is done using the pointers, so
that results in an intel_fb_obj_flush() call. The problem is that the
dirtyfb is passing ORIGIN_GTT, so it is being ignored by FBC - even
though the hardware tracking is not detecing the WC mmap operations.
So in order to fix that without having to give up the automatic
hardware tracking for GTT mmaps we transform the flush operation from
dirtyfb into a special operation: ORIGIN_DIRTYFB.
This commit fixes all the kms_frontbuffer_tracking subtests that
contain "fbc" and "mmap-wc" in their names and are currently failing
(for a total of 16 subtests).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
