This reverts commit 62469c7600 ("net: ethernet: bcmgenet: use phydev
from struct net_device") because it causes GENETv1/2/3 adapters to
expose the following behavior after an ifconfig down/up sequence:
PING fainelli-linux (10.112.156.244): 56 data bytes
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.352 ms
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.472 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.496 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.517 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.536 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.557 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=752.448 ms (DUP!)
This was previously fixed by commit 5dbebbb44a ("net: bcmgenet:
Software reset EPHY after power on") but the commit we are reverting was
essentially making this previous commit void, here is why.
Without commit 62469c7600 we would have the following scenario after
an ifconfig down then up sequence:
- bcmgenet_open() calls bcmgenet_power_up() to make sure the PHY is
initialized *before* we get to initialize the UniMAC, this is
critical to ensure the PHY is in a correct state, priv->phydev is
valid, this code executes fine
- second time from bcmgenet_mii_probe(), through the normal
phy_init_hw() call (which arguably could be optimized out)
Everything is fine in that case. With commit 62469c7600, we would have
the following scenario to happen after an ifconfig down then up
sequence:
- bcmgenet_close() calls phy_disonnect() which makes dev->phydev become
NULL
- when bcmgenet_open() executes again and calls bcmgenet_mii_reset() from
bcmgenet_power_up() to initialize the internal PHY, the NULL check
becomes true, so we do not reset the PHY, yet we keep going on and
initialize the UniMAC, causing MAC activity to occur
- we call bcmgenet_mii_reset() from bcmgenet_mii_probe(), but this is
too late, the PHY is botched, and causes the above bogus pings/packets
transmission/reception to occur
Reported-by: Jaedon Shin <jaedon.shin@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FEC receive accelerator (RACC) supports shifting the data payload of
received packets by 16-bits, which aligns the payload (IP header) on a
4-byte boundary, which is, if not required, at least strongly suggested
by the Linux networking layer.
Without this patch, a huge number of alignment faults will be taken by the
IP stack, as seen in /proc/cpu/alignment:
~/$ cat /proc/cpu/alignment
User: 0
System: 72645 (inet_gro_receive+0x104/0x27c)
Skipped: 0
Half: 0
Word: 0
DWord: 0
Multi: 72645
User faults: 3 (fixup+warn)
This patch was suggested by Andrew Lunn in this message to linux-netdev:
http://marc.info/?l=linux-arm-kernel&m=147465452108384&w=2
and adapted from a patch by Russell King from 2014:
http://git.arm.linux.org.uk/cgit/linux-arm.git/commit/?id=70d8a8a
Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the i.MX27 reference manual, this SoC does not have support
for the receive accelerator (RACC) register at offset 0x1C4.
http://cache.nxp.com/files/32bit/doc/ref_manual/MCIMX27RM.pdf
Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the i.MX25 reference manual, this SoC does not have support
for the receive accelerator (RACC) register at offset 0x1C4.
http://www.nxp.com/files/dsp/doc/ref_manual/IMX25RM.pdf
Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleans devlink resources by calling devlink_port_unregister()
to avoid the following issues:
- Kernel panic when triggering reset flow.
- Memory leak due to unfreed resources in mlx4_init_port_info().
Fixes: 09d4d087cd ("mlx4: Implement devlink interface")
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were missing check for 25G and 100G while checking port speed,
which lead to less number of queues getting allocated for 25G & 100G
adapters and leading to low throughput. Adding the missing check for
both NIC and vNIC driver.
Also fixes port advertisement for 25G and 100G in ethtool output.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit fe56b9e6a8 ("qed: Add module with basic common support")
has introduced a stack corruption during probe, where filling a
local struct with data to be sent to management firmware is incorrectly
filled; The data is written outside of the struct and corrupts
the stack.
Changes from v1:
----------------
- Correct the value written [Caught by David Laight]
Fixes: fe56b9e6a8 ("qed: Add module with basic common support")
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
E-switch mode changes involve creating HW tables, potentially allocating
netdevices, etc, and things can fail. Add an attempt to rollback to the
existing mode when changing to the new mode fails. Only if rollback fails,
getting proper SRIOV functionality requires module unload or sriov
disablement/enablement.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When enablement of the SRIOV e-switch in certain mode (switchdev or legacy)
fails, we must set the mode to none. Otherwise, we'll run into double free
based crashes when further attempting to deal with the e-switch (such
as when disabling sriov or unloading the driver).
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FW command output length should be only the length of struct
mlx5_cmd_fc_bulk out field. Failing to do so will cause the memcpy
call which is invoked later in the driver to write over wrong memory
address and corrupt kernel memory which results in random crashes.
This bug was found using the kernel address sanitizer (kasan).
Fixes: a351a1b03b ('net/mlx5: Introduce bulk reading of flow counters')
Signed-off-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MAC devices use the RWKPKTEN and MGKPKTEN bits of the PMT Control/Status
register to generate power management events.
So this patch is to properly set the RWKPKTEN [BIT(2)] inside the
PMT register (needed in case of global unicast).
Reported-by: Aditi SHARMA <aditi-hed.sharma@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 6e7333d "net: add rx_nohandler stat counter" added the new entry
rx_nohandler into struct rtnl_link_stats64. Unfortunately the bna
driver foolishly depends on the structure. It uses part of it for
ethtool statistics and it's not bad but the driver assumes its size
is constant as it defines string for each existing entry. The problem
occurs when the structure is extended because you need to modify bna
driver as well. If not any attempt to retrieve ethtool statistics results
in crash in bnad_get_strings().
The patch changes BNAD_ETHTOOL_STATS_NUM so it counts real number of
strings in the array and also removes rtnl_link_stats64 entries that
are not used in output and are always zero.
Fixes: 6e7333d "net: add rx_nohandler stat counter"
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit ba5ca784 "bna: check for dma mapping errors" added besides other
things a statistic that counts number of DMA buffer mapping failures
per each Rx queue. This counter is not included in ethtool stats output.
Fixes: ba5ca784 "bna: check for dma mapping errors"
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 73725d9dfd ("nfp: allocate ring SW structs dynamically")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
for preventing race conditions within ioctl calls.
Signed-off-by: Ivan Mikhaylov <ivan@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
add realization for mac address set and remove dummy callback.
Signed-off-by: Ivan Mikhaylov <ivan@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device table is required to load modules based on
modaliases. After adding MODULE_DEVICE_TABLE, below entries
for example will be added to modules.alias:
alias of:N*T*Cmediatek,mt7623-ethC* mtk_eth_soc
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an error occurs in mlx4_init_eq_table the index used in the
err_out_unmap label is one too big which results in a panic in
mlx4_free_eq. This patch fixes the index in the error path.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When system enters into kdump kernel because of kernel panic, it won't
shutdown devices. On-flight DMA will continue transferring data until
device driver initializes. All devices are supposed to reset during
driver initialization. And this property is used to fix the kdump
failure in system with intel iommu. Other systems with hardware iommu
should be similar. Please check commit 091d42e ("iommu/vt-d: Copy
translation tables from old kernel") and those commits around.
But bnx2 driver doesn't reset device during driver initialization. The
device resetting is deferred to net device up stage. This will cause
hardware iommu handling failure on bnx2 device. And its resetting relies
on firmware. So in this patch move the firmware requesting code to earlier
bnx2_init_one(), then next call bnx2_reset_chip to reset device.
Signed-off-by: Baoquan He <bhe@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When port is down, tx drop counter update is not needed.
Updating the counter in this case can cause a kernel
panic as when the port is down, ring can be NULL.
Fixes: 63a664b7e9 ("net/mlx4_en: fix tx_dropped bug")
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a capability check before enabling DCBX.
In addition, it re-organizes the relevant data structures,
and fixes a typo in a define.
Fixes: af7d518526 ("net/mlx4_en: Add DCB PFC support through CEE netlink commands")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4_en_dcbnl_set_state() returns u8, the return value from
mlx4_en_setup_tc() could be negative in case of failure, so fix that.
Fixes: af7d518526 ("net/mlx4_en: Add DCB PFC support through CEE netlink commands")
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4_en_dcbnl_set_all() returns u8, so return value can't be negative in
case of failure.
Fixes: af7d518526 ("net/mlx4_en: Add DCB PFC support through CEE netlink commands")
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Rana Shahout <ranas@mellanox.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to a mistake in the hardware manual, the FWSLC and POST1-4 registers
were not documented and left out of the driver for RZ/A making the CAM
feature non-operational.
Additionally, when the offset values for POST1-4 are left blank, the driver
attempts to set them using an offset of 0xFFFF which can cause a memory
corruption or panic.
This patch fixes the panic and properly enables CAM.
Reported-by: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We move register_netdev() to the end of dwceqos_probe() to close any
races where the netdev callbacks are called before the initialization
has finished.
Reported-by: Pavel Andrianov <andrianov@ispras.ru>
Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During port init, we currently set the port's type to Ethernet after
setting its MAC address. However, the hardware documentation states this
should be the other way around.
Align the driver with the hardware documentation and set the port's MAC
address after setting its type.
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When neigh_init fails, we have to do proper cleanup including
router_fini call.
Fixes: 6cf3c971dc ("mlxsw: spectrum_router: Add private neigh table")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to pad frames to ETH_ZLEN on RX.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Dinan Gunawardena <dinan.gunawardena@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Be more strict about FW versions. Drop support for old
transitional revisions which were never used in production.
Dropping support for FW ABI version 0.0.0.0 is particularly
useful because 0 could just be uninitialized memory.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dinan Gunawardena <dinan.gunawardena@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unnecessary version.h includes.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Dinan Gunawardena <dinan.gunawardena@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently vlan tagged packets were not parsed correctly
and assumed to be regular IPv4/IPv6 packets.
We should check for 802.1Q/802.1ad tags and update the lro header
accordingly.
This fixes the use case where LRO is on and rxvlan is off
(vlan stripping is off).
Fixes: e586b3b0ba ('net/mlx5: Ethernet Datapath files')
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when reading global PFC statistics we left the counter
iterator out of the equation and we ended up reading the same counter
over and over again.
Instead of reading the counter at index 0 on every iteration we now read
the counter at index (i).
Fixes: e989d5a532 ('net/mlx5e: Expose flow control counters to ethtool')
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 64 bits architectures unsigned long is longer than u32,
casting to unsigned long will result in overflow.
We need to first allocate an unsigned long variable, then assign the
wanted value.
Fixes: 665bc53969 ('net/mlx5e: Use new ethtool get/set link ksettings API')
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the xmit_more counter before notifying the HW,
to prevent a possible use-after-free of the skb.
Fixes: c8cf78fe10 ("net/mlx5e: Add ethtool counter for TX xmit_more")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a code path where we are calling __iowrite64_copy() on
an address that is not 64-bit aligned. This causes an exception on
some architectures such as arm64. Fix that code path by using
__iowrite32_copy().
Reported-by: JD Zheng <jiandong.zheng@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The build of m32r was giving warning:
In file included from drivers/net/ethernet/smsc/smc91x.c:92:0:
drivers/net/ethernet/smsc/smc91x.h:448:0: warning: "SMC_inb" redefined
#define SMC_inb(ioaddr, reg) ({ BUG(); 0; })
drivers/net/ethernet/smsc/smc91x.h:106:0:
note: this is the location of the previous definition
#define SMC_inb(a, r) inb(((u32)a) + (r))
drivers/net/ethernet/smsc/smc91x.h:449:0: warning: "SMC_outb" redefined
#define SMC_outb(x, ioaddr, reg) BUG()
drivers/net/ethernet/smsc/smc91x.h:108:0:
note: this is the location of the previous definition
#define SMC_outb(v, a, r) outb(v, ((u32)a) + (r))
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
I'm still struggling to get this fix right..
Changes since v2:
- do not blindly modify SKB contents according to Dave's legitimate
objection
Changes since v1:
- dropped disabling HW checksum offload for Zynq
- initialize checksum similar to net/ethernet/freescale/fec_main.c
-- >8 --
MACB/GEM needs the checksum field initialized to 0 to get correct
results on transmit in all cases, e.g. on Zynq, UDP packets with
payload <= 2 otherwise contain a wrong checksums.
Signed-off-by: Helmut Buchsbaum <helmut.buchsbaum@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The /proc/irq/xx information is incorrect for smsc911x because
the request_irq is happening before the register_netdev has the
proper device name. Moving it to the open also fixes the case
of when the device is renamed.
Reported-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for the allocating/enabling interrupts
in the ndo_open routine move the irq handler before it.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move phy startup/shutdown into the smsc911x_open/stop routines. This
allows the module to be unloaded because phy_connect_direct is no longer
always holding the module use count. This one change also resolves a
number of other problems.
The link status of a downed interface no longer reflects a stale state.
Errors caused by the net device being opened before the mdio/phy was
configured. There is also a potential power savings as the phy's don't
remain powered when the interface isn't running.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rework the error handling in smsc911x open in preparation
for the mdio startup being moved here.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When PCI error is detected, in some architectures (like PowerPC) a slot
reset is performed - the driver's error handlers are in charge of "disable"
device before the reset, and re-enable it after a successful slot reset.
There are two cases though that another path is taken on the code: if the
slot reset is not successful or if too many errors already happened in the
specific adapter (meaning that possibly the device is experiencing a HW
failure that slot reset is not able to solve), the core PCI error mechanism
(called EEH in PowerPC) will remove the adapter from the system, since it
will consider this as a permanent failure on device. In this case, a path
is taken that leads to bnx2x_chip_cleanup() calling bnx2x_reset_hw(), which
then tries to perform a HW reset on chip. This reset won't succeed since
the HW is in a fault state, which can be seen by multiple messages on
kernel log like below:
bnx2x: [bnx2x_issue_dmae_with_comp:552(eth1)]DMAE timeout!
bnx2x: [bnx2x_write_dmae:600(eth1)]DMAE returned failure -1
After some time, the PCI error mechanism gives up on waiting the driver's
correct removal procedure and forcibly remove the adapter from the system.
We can see soft lockup while core PCI error mechanism is waiting for driver
to accomplish the right removal process.
This patch adds a verification to avoid a chip reset whenever the function
is in PCI error state - since this case is only reached when we have a
device being removed because of a permanent failure, the HW chip reset is
not expected to work fine neither is necessary.
Also, as a minor improvement in error path, we avoid the MCP information dump
in case of non-recoverable PCI error (when adapter is about to be removed),
since it will certainly fail.
Reported-by: Harsha Thyagaraja <hathyaga@in.ibm.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Acked-By: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On ThunderX 88xx pass 2.x chips when TSO is offloaded to HW,
HW posts a CQE for every TSO segment transmitted. Current code
does handles this, but is prone to issues when segment sizes are
small resulting in SW processing too many CQEs and also at times
frees a SKB which is not yet transmitted.
This patch handles the errata in a different way and eliminates issues
with earlier approach, TSO packet is submitted to HW with post_cqe=0,
so that no CQE is posted upon completion of transmission of TSO packet
but a additional HDR + IMMEDIATE descriptors are added to SQ due to
which a CQE is posted and will have required info to be used while
cleanup in napi. This way only one CQE is posted for a TSO packet.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a issue in HW where-in while sending GSO sized pkts
as part of TSO, if pkt len falls below configured min packet
size i.e 60, NIC will zero PAD packet and also updates IP total length.
Hence set this value to lessthan min pkt size of MAC + IP + TCP
headers, BGX will anyway do the padding to transmit 64 byte pkt
including FCS.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If DCB is configured on the link partner switch with an
unsupported traffic class configuration (e.g. non-contiguous TCs),
the driver is flagging DCB as disabled. But, for future DCB
LLDPDUs, the driver was checking if the interface was DCB capable
instead of enabled. This was causing a kernel panic when LLDP
was enabled/disabled on the link partner switch.
This patch corrects the situation by having the LLDP event handler
check the correct flag in the pf structure. It also cleans up the
setting and clearing of the enabled flag for other checks.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent commit 087d7a8c91 "tg3: Fix for diasllow rx coalescing
time to be 0" disallow to set Rx coalescing time to be 0 as this stops
generating interrupts for the incoming packets. I found the zero
Tx coalescing time stops generating interrupts for outgoing packets
as well and fires Tx watchdog later. To avoid this, don't allow to set
Tx coalescing time to 0 and also remove subsequent checks that become
senseless.
Cc: satish.baddipadige@broadcom.com
Cc: siva.kallam@broadcom.com
Cc: michael.chan@broadcom.com
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Siva Reddy Kallam <siva.kallam@broadcom.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/qlogic/qed/qed_dcbx.c:1230:13-20: WARNING: kzalloc should be used for dcbx_info, instead of kmalloc/memset
drivers/net/ethernet/qlogic/qed/qed_dcbx.c:1192:13-20: WARNING: kzalloc should be used for dcbx_info, instead of kmalloc/memset
Use kzalloc rather than kmalloc followed by memset with 0
This considers some simple cases that are common and easy to validate
Note in particular that there are no ...s in the rule, so all of the
matched code has to be contiguous
Generated by: scripts/coccinelle/api/alloc/kzalloc-simple.cocci
CC: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a VLAN is added on a bridge port we should use the existing unicast
flood configuration of the port instead of assuming it's enabled.
Fixes: 0293038e0c ("mlxsw: spectrum: Add support for flood control")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 14d39461b3 ("mlxsw: spectrum: Use per-FID struct for the
VLAN-aware bridge") I added a per-FID struct, which member ports can
take a reference on upon VLAN membership configuration.
However, sometimes only the VLAN flags (e.g. egress untagged) are
toggled without changing the VLAN membership. In these cases we
shouldn't take another reference on the FID.
Fixes: 14d39461b3 ("mlxsw: spectrum: Use per-FID struct for the VLAN-aware bridge")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the notifier is registered for every asic instance, however the
same block. Fix this by moving the registration to module init.
Fixes: c723c735fa ("mlxsw: spectrum_router: Periodically update the kernel's neigh table")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
