The driver is currently assuming that it is operating with a 28nm
process chip, which has a specific formula to convert temperature to a
code and vice versa. Update the code to support providing two key
values: offset and multiplier to derive the correct formulas.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200114190607.29339-3-f.fainelli@gmail.com
At the time the brcmstb_thermal driver and its binding were merged, the
DT binding did not make the coefficients properties a mandatory one,
therefore all users of the brcmstb_thermal driver out there have a non
functional implementation with zero coefficients. Even if these
properties were provided, the formula used for computation is incorrect.
The coefficients are entirely process specific (right now, only 28nm is
supported) and not board or SoC specific, it is therefore appropriate to
hard code them in the driver given the compatibility string we are
probed with which has to be updated whenever a new process is
introduced.
We remove the existing coefficients definition since subsequent patches
are going to add support for a new process and will introduce new
coefficients as well.
Fixes: 9e03cf1b2d ("thermal: add brcmstb AVS TMON driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200114190607.29339-2-f.fainelli@gmail.com
rcar_thermal_update_temp() takes a mutex, so it is always called in a
context that can sleep. Hence replace the 300 µs busy loop by a call to
usleep_range(), to allow other threads to run.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200115125417.5263-1-geert+renesas@glider.be
This builds the BCM2711 thermal driver as module for the Raspberry Pi 4.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1578941778-23321-5-git-send-email-stefan.wahren@i2se.com
This enables thermal for the BCM2711 (used on Raspberry Pi 4) by adding
the AVS monitor and a subnode for the thermal part.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1578941778-23321-4-git-send-email-stefan.wahren@i2se.com
This adds the thermal sensor driver for the Broadcom BCM2711 SoC,
which is placed on the Raspberry Pi 4. The driver only provides
SoC temperature reading so far.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1578941778-23321-3-git-send-email-stefan.wahren@i2se.com
Since the BCM2711 doesn't have a AVS TMON block, the thermal information
must be retrieved from the AVS ring oscillator block. This block is part
of the AVS monitor which contains a bunch of raw sensors.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1578941778-23321-2-git-send-email-stefan.wahren@i2se.com
The cp_ft_flag variable is not used after initialization, so delete
it. After that, THS_EFUSE_CP_FT_MASK, THS_EFUSE_CP_FT_BIT and
THS_CALIBRATION_IN_FT are not needed, so delete them.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200112180925.23705-1-tiny.windzz@gmail.com
sparse returns a warning:
"drivers/thermal/sun8i_thermal.c:341:60: sparse: sparse: Using plain
integer as NULL pointer".
Fix it by replacing the zero integer by a NULL pointer.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200112171318.23025-1-tiny.windzz@gmail.com
According to the spec, r40 has 2 thermal sensors.
Sensor0 located in the CPU, another in the GPU.
Fixes: dccc5c3b6f ("thermal/drivers/sun8i: Add thermal driver for H6/H5/H3/A64/A83T/R40")
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Tested-on: sun8i-r40-bananapi-m2-ultra
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200106174639.20862-1-tiny.windzz@gmail.com
Michael Chan says:
====================
bnxt_en: Updates for net-next.
This patch-set includes link up and link initialization improvements,
RSS and aRFS improvements, devlink refactoring and registration
improvements, devlink info support including documentation.
v2: Removed the TC ingress rate limiting patch. The developer Harsha needs
to rework some code.
Use fw.psid suggested by Jakub Kicinski.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the set of info versions reported by bnxt_en driver, including
a description of what the version represents, and what modes (fixed,
running, stored) it reports.
v2: Use fw.psid.
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Display the following information via devlink info command:
- Driver name
- Board id
- Broad revision
- Board Serial number
- Board FW version
- FW parameter set version
- FW App version
- FW management version
- FW RoCE version
Standard output example:
$ devlink dev info pci/0000:3b:00.0
pci/0000:3b:00.0:
driver bnxt_en
serial_number 00-10-18-FF-FE-AD-05-00
versions:
fixed:
asic.id D802
asic.rev 1
running:
fw 216.1.124.0
fw.psid 0.0.0
fw.app 216.1.122.0
fw.mgmt 864.0.32.0
fw.roce 216.1.15.0
[ This version has incorporated changes suggested by Jakub Kicinski to
use generic devlink version tags. ]
v2: Use fw.psid
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add definition and documentation for the new generic info "fw.roce".
v2: Remove board.nvm_cfg since fw.psid is similar.
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of switch_id, renaming it to dsn will be more meaningful
so that it can be used to display device serial number in follow up
patch via devlink_info command.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds status notification to devlink flash update
while flashing is in progress.
$ devlink dev flash pci/0000:05:00.0 file 103.pkg
Preparing to flash
Flashing done
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Latest kernels get the phys_port_name via devlink, if
ndo_get_phys_port_name is not defined. To provide the phys_port_name
correctly, register devlink before registering netdev.
Also call devlink_port_type_eth_set() after registering netdev as
devlink port updates the netdev structure and notifies user.
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will allow to register for devlink port and use port features.
Also register params only if firmware spec version is at least 0x10600
which will support reading/setting numbered variables in NVRAM.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define bnxt_dl_params_register() and bnxt_dl_params_unregister()
functions and move params register/unregister code to these newly
defined functions. This patch is in preparation to register
devlink irrespective of firmware spec. version in the next patch.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware bug has been fixed on B0 and newer chips, so disable the
workaround on these chips.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the only time we check and remove expired filters is
when we are inserting new filters.
Improving the aRFS expiry handling by adding code to do the above
work periodically.
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In bnxt_rx_flow_steer(), if the dissected packet is a fragment, do not
proceed to create the ntuple filter and return error instead. Otherwise
we would create a filter with 0 source and destination ports because
the dissected ports would not be available for fragments.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
575XX (P5) chips have the same UDP RSS hashing capability as P4 chips,
so we can enable it on P5 chips.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dev_port is meant to distinguish the network ports belonging to
the same PCI function. Our devices only have one network port
associated with each PCI function and so we should not set it for
correctness.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the 2nd parameter fw_dflt is not set, we are calling bnxt_probe_phy()
after the firmware has reset. There is no need to query the current
PHY settings from firmware as these settings may be different from
the ethtool settings that the driver will re-establish later. So
return earlier in bnxt_probe_phy() to save one firmware call.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In bnxt_update_phy_setting(), ethtool_get_link_ksettings() and
bnxt_disable_an_for_lpbk(), we inconsistently use netif_carrier_ok()
to determine link. Instead, we should use bp->link_info.link_up
which has the true link state. The netif_carrier state may be off
during self-test and while the device is being reset and may not always
reflect the true link state.
By always using bp->link_info.link_up, the code is now more
consistent and more correct. Some unnecessary link toggles are
now prevented with this patch.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kubecek says:
====================
ethtool netlink interface, part 2
This shorter series adds support for getting and setting of wake-on-lan
settings and message mask (originally message level). Together with the
code already in net-next, this will allow full implementation of
"ethtool <dev>" and "ethtool -s <dev> ...".
Older versions of the ethtool netlink series allowed getting WoL settings
by unprivileged users and only filtered out the password but this was
a source of controversy so for now, ETHTOOL_MSG_WOL_GET request always
requires CAP_NET_ADMIN as ETHTOOL_GWOL ioctl request does.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Send ETHTOOL_MSG_WOL_NTF notification whenever wake-on-lan settings of
a device are modified using ETHTOOL_MSG_WOL_SET netlink message or
ETHTOOL_SWOL ioctl request.
As notifications can be received by anyone, do not include SecureOn(tm)
password in notification messages.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement WOL_SET netlink request to set wake-on-lan settings. This is
equivalent to ETHTOOL_SWOL ioctl request.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement WOL_GET request to get wake-on-lan settings for a device,
traditionally available via ETHTOOL_GWOL ioctl request.
As part of the implementation, provide symbolic names for wake-on-line
modes as ETH_SS_WOL_MODES string set.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Send ETHTOOL_MSG_DEBUG_NTF notification message whenever debugging message
mask for a device are modified using ETHTOOL_MSG_DEBUG_SET netlink message
or ETHTOOL_SMSGLVL ioctl request.
The notification message has the same format as reply to DEBUG_GET request.
As with other ethtool notifications, netlink requests only trigger the
notification if the mask is actually changed while ioctl request trigger it
whenever the request results in calling the ethtool_ops handler.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement DEBUG_SET netlink request to set debugging settings for a device.
At the moment, only message mask corresponding to message level as set by
ETHTOOL_SMSGLVL ioctl request can be set. (It is called message level in
ioctl interface but almost all drivers interpret it as a bit mask.)
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement DEBUG_GET request to get debugging settings for a device. At the
moment, only message mask corresponding to message level as reported by
ETHTOOL_GMSGLVL ioctl request is provided. (It is called message level in
ioctl interface but almost all drivers interpret it as a bit mask.)
As part of the implementation, provide symbolic names for message mask bits
as ETH_SS_MSG_CLASSES string set.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix missing or incorrect function argument and struct member descriptions.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
* pm-core:
PM-runtime: add tracepoints for usage_count changes
* powercap:
powercap/intel_rapl: add support for JasperLake
x86/cpu: Add Jasper Lake to Intel family
powercap/intel_rapl: add support for TigerLake Mobile
* pm-opp:
opp: Replace list_kref with a local counter
opp: Free static OPPs on errors while adding them
* pm-avs:
power: avs: qcom-cpr: remove duplicated include from qcom-cpr.c
power: avs: fix uninitialized error return on failed cpr_read_fuse_uV() call
power: avs: qcom-cpr: make cpr_get_opp_hz_for_req() static
power: avs: qcom-cpr: remove set but unused variable
power: avs: qcom-cpr: make sure that regmap is available
power: avs: qcom-cpr: fix unsigned expression compared with zero
power: avs: qcom-cpr: fix invalid printk specifier in debug print
power: avs: Add support for CPR (Core Power Reduction)
dt-bindings: power: avs: Add support for CPR (Core Power Reduction)
* pm-misc:
mailmap: Add entry for <rjw@sisk.pl>
* pm-cpufreq:
cpufreq: loongson2_cpufreq: adjust cpufreq uses of LOONGSON_CHIPCFG
cpufreq: brcmstb-avs: fix imbalance of cpufreq policy refcount
cpufreq: intel_pstate: fix spelling mistake: "Whethet" -> "Whether"
cpufreq: s3c: fix unbalances of cpufreq policy refcount
cpufreq: imx-cpufreq-dt: Add i.MX8MP support
cpufreq: Use imx-cpufreq-dt for i.MX8MP's speed grading
cpufreq: tegra186: convert to devm_platform_ioremap_resource
cpufreq: kirkwood: convert to devm_platform_ioremap_resource
cpufreq: CPPC: put ACPI table after using it
cpufreq : CPPC: Break out if HiSilicon CPPC workaround is matched
* pm-sleep:
PM: suspend: Add sysfs attribute to control the "sync on suspend" behavior
PM: hibernate: fix spelling mistake "shapshot" -> "snapshot"
PM: hibernate: Add more logging on hibernation failure
PM: hibernate: improve arithmetic division in preallocate_highmem_fraction()
PM: wakeup: Show statistics for deleted wakeup sources again
PM: sleep: Switch to rtc_time64_to_tm()/rtc_tm_to_time64()
* pm-cpuidle: (27 commits)
intel_idle: Clean up irtl_2_usec()
intel_idle: Move 3 functions closer to their callers
intel_idle: Annotate initialization code and data structures
intel_idle: Move and clean up intel_idle_cpuidle_devices_uninit()
intel_idle: Rearrange intel_idle_cpuidle_driver_init()
intel_idle: Clean up NULL pointer check in intel_idle_init()
intel_idle: Fold intel_idle_probe() into intel_idle_init()
intel_idle: Eliminate __setup_broadcast_timer()
cpuidle: fix cpuidle_find_deepest_state() kerneldoc warnings
cpuidle: sysfs: fix warnings when compiling with W=1
cpuidle: coupled: fix warnings when compiling with W=1
Documentation: admin-guide: PM: Add intel_idle document
cpuidle: arm: Enable compile testing for some of drivers
cpuidle: Drop unused cpuidle_driver_ref/unref() functions
intel_idle: Use ACPI _CST on server systems
intel_idle: Add module parameter to prevent ACPI _CST from being used
intel_idle: Allow ACPI _CST to be used for selected known processors
cpuidle: Allow idle states to be disabled by default
intel_idle: Use ACPI _CST for processor models without C-state tables
intel_idle: Refactor intel_idle_cpuidle_driver_init()
...
Second set of patches for v5.6. Nothing special standing out, smaller
new features and fixes allover.
Major changes:
ar5523
* add support for SMCWUSBT-G2 USB device
iwlwifi
* support new versions of the FTM FW APIs
* support new version of the beacon template FW API
* print some extra information when the driver is loaded
rtw88
* support wowlan feature for 8822c
* add support for WIPHY_WOWLAN_NET_DETECT
brcmfmac
* add initial support for monitor mode
qtnfmac
* add module parameter to enable DFS offloading in firmware
* add support for STA HE rates
* add support for TWT responder and spatial reuse
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJeLcWsAAoJEG4XJFUm622bDGUIAJuhM4LiDAzOGnDjH5cMosOC
/qwDpGD19cEeVAhNSMKUn7Uo9+qbQYIleiO7XXxzCuJceYbxbT5s3Vb/fWsRUPjS
cBDmGuK8/giqMQJshXvfCTsoF83CyirCjY/MJvomK2BRlXM8hQ3s6hAcfU0zQ96e
OU1akcfZzUwjaBKaDYLncxLuGbeUXMy8AZwFdgQlQRMoObpen/IIwx6jDK/A+3l6
VCOJF+JTkDytfNWmTpZ65uJrYEXoLe6G4028FjOI4BDFmEgvdHC5vTm7VOBhrkuB
9tsKcYNvECCNn2WI96V+etD8kaZPscQIW8hgOrYyGxw43lJg5zH4Z9eWAmHojxE=
=UOhb
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-01-26' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.6
Second set of patches for v5.6. Nothing special standing out, smaller
new features and fixes allover.
Major changes:
ar5523
* add support for SMCWUSBT-G2 USB device
iwlwifi
* support new versions of the FTM FW APIs
* support new version of the beacon template FW API
* print some extra information when the driver is loaded
rtw88
* support wowlan feature for 8822c
* add support for WIPHY_WOWLAN_NET_DETECT
brcmfmac
* add initial support for monitor mode
qtnfmac
* add module parameter to enable DFS offloading in firmware
* add support for STA HE rates
* add support for TWT responder and spatial reuse
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Yoshiki Komachi says:
====================
When I tried a test based on the selftest program for BPF flow dissector
(test_flow_dissector.sh), I observed unexpected result as below:
$ tc filter add dev lo parent ffff: protocol ip pref 1337 flower ip_proto \
udp src_port 8-10 action drop
$ tools/testing/selftests/bpf/test_flow_dissector -i 4 -f 9 -F
inner.dest4: 127.0.0.1
inner.source4: 127.0.0.3
pkts: tx=10 rx=10
The last rx means the number of received packets. I expected rx=0 in this
test (i.e., all received packets should have been dropped), but it resulted
in acceptance.
Although the previous commit 8ffb055bea ("cls_flower: Fix the behavior
using port ranges with hw-offload") added new flag and field toward filtering
based on port ranges with hw-offload, it missed applying for BPF flow dissector
then. As a result, BPF flow dissector currently stores data extracted from
packets in incorrect field used for exact match whenever packets are classified
by filters based on port ranges. Thus, they never match rules in such cases
because flow dissector gives rise to generating incorrect flow keys.
This series fixes the issue by replacing incorrect flag and field with new
ones in BPF flow dissector, and adds a test for filtering based on specified
port ranges to the existing selftest program.
Changes in v2:
- set key_ports to NULL at the top of __skb_flow_bpf_to_target()
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Add a simple test to make sure that a filter based on specified port
range classifies packets correctly.
Signed-off-by: Yoshiki Komachi <komachi.yoshiki@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Petar Penkov <ppenkov@google.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200117070533.402240-3-komachi.yoshiki@gmail.com
This patch applies new flag (FLOW_DISSECTOR_KEY_PORTS_RANGE) and
field (tp_range) to BPF flow dissector to generate appropriate flow
keys when classified by specified port ranges.
Fixes: 8ffb055bea ("cls_flower: Fix the behavior using port ranges with hw-offload")
Signed-off-by: Yoshiki Komachi <komachi.yoshiki@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Petar Penkov <ppenkov@google.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200117070533.402240-2-komachi.yoshiki@gmail.com
Johan Hedberg says:
====================
pull request: bluetooth-next 2020-01-26
Here's (probably) the last bluetooth-next pull request for the 5.6 kernel.
- Initial pieces of Bluetooth 5.2 Isochronous Channels support
- mgmt: Various cleanups and a new Set Blocked Keys command
- btusb: Added support for 04ca:3021 QCA_ROME device
- hci_qca: Multiple fixes & cleanups
- hci_bcm: Fixes & improved device tree support
- Fixed attempts to create duplicate debugfs entries
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
'alloc_etherdev_mqs()' expects first 'tx', then 'rx'. The semantic here
looks reversed.
Reorder the arguments passed to 'alloc_etherdev_mqs()' in order to keep
the correct semantic.
In fact, this is a no-op because both XGENE_NUM_[RT]X_RING are 8.
Fixes: 107dec2749 ("drivers: net: xgene: Add support for multiple queues")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we depend on rcu_call() and synchronize_rcu() to also wait
for preempt_disabled region to complete the rcu read critical section
in __dev_map_flush() is no longer required. Except in a few special
cases in drivers that need it for other reasons.
These originally ensured the map reference was safe while a map was
also being free'd. And additionally that bpf program updates via
ndo_bpf did not happen while flush updates were in flight. But flush
by new rules can only be called from preempt-disabled NAPI context.
The synchronize_rcu from the map free path and the rcu_call from the
delete path will ensure the reference there is safe. So lets remove
the rcu_read_lock and rcu_read_unlock pair to avoid any confusion
around how this is being protected.
If the rcu_read_lock was required it would mean errors in the above
logic and the original patch would also be wrong.
Now that we have done above we put the rcu_read_lock in the driver
code where it is needed in a driver dependent way. I think this
helps readability of the code so we know where and why we are
taking read locks. Most drivers will not need rcu_read_locks here
and further XDP drivers already have rcu_read_locks in their code
paths for reading xdp programs on RX side so this makes it symmetric
where we don't have half of rcu critical sections define in driver
and the other half in devmap.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Link: https://lore.kernel.org/bpf/1580084042-11598-4-git-send-email-john.fastabend@gmail.com
virtio_net currently relies on rcu critical section to access the xdp
program in its xdp_xmit handler. However, the pointer to the xdp program
is only used to do a NULL pointer comparison to determine if xdp is
enabled or not.
Use rcu_access_pointer() instead of rcu_dereference() to reflect this.
Then later when we drop rcu_read critical section virtio_net will not
need in special handling.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Link: https://lore.kernel.org/bpf/1580084042-11598-3-git-send-email-john.fastabend@gmail.com
Now that we rely on synchronize_rcu and call_rcu waiting to
exit perempt-disable regions (NAPI) lets update the comments
to reflect this.
Fixes: 0536b85239 ("xdp: Simplify devmap cleanup")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/1580084042-11598-2-git-send-email-john.fastabend@gmail.com
Defaults for min_mtu and max_mtu are set by ether_setup(), which is
called from devm_alloc_etherdev(). Let rtl_jumbo_max() only return
a positive value if actually jumbo packets are supported. This also
allows to remove constant Jumbo_1K which is a little misleading anyway.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An 'alloc_etherdev()' called is not ballanced by a corresponding
'free_netdev()' call in one error handling path.
Slighly reorder the error handling code to catch the missed case.
Fixes: c100e47caa ("mlxsw: minimal: Add ethtool support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
