This finishes off the conversion to the new ethtool API by removing the
old macros being used in i40e_set_link_ksettings and replacing them with
shiny new ones.
This conversion also allows us to provide link speed support for new 25G
and 10G macros which is included here as well.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This variable isn't actually very descriptive and makes the code a bit
confusing as to what it is being used for. This patch enhances the
variable with the longer name, 'autoneg_changed', which makes it clear
we are concerned with autoneg changing in this context.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This removes references to old ethtool API macros and functions in
i40e_get_settings_link_up as part of the process of converting to the
new API. The new API also allows us to provide more explicit support
for new 25G and 10G PHY types so some of the PHY types have been
adjusted where necessary as well.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We are still largely using the old ethtool API macros. This is
problematic because eventually they will be removed and they only
support 32 bits of PHY types.
This overhauls i40e_phy_type_to_ethtool to use only the new API. Doing
this also allows us to provide much better support for newer 25G and 10G
PHY types which is included here as well.
The remaining usages of the old ethtool API will be addressed in other
patches in the series.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for 25G Active Optical Cables (AOC) and Active
Copper Cables (ACC) PHY types.
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Signed-off-by: Krzysztof Malek <krzysztof.malek@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This separates the setting of autoneg in i40e_phy_types_to_ethtool into
its own conditional. Doing this adds clarity as what PHYs
support/advertise autoneg and makes it easier to add new PHY types in
the future.
This also fixes an issue on devices with CRT_RETIMER where advertising
autoneg was being set, but supported autoneg was not.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There's a number of minor incidental whitespace issues in this file.
This addresses most of the ones I could find.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Someone forgot a word in this comment and it's confusing without it.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function header erroneously listed 'phy_types' as a parameter. The
correct parameter is 'pf'.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This fixes two issues in i40e_get_link_ksettings. It adds calls to
ethtool_link_ksettings_zero_link_mode to make sure advertising and
supported link masks are cleared before we start setting bits in them.
This also replaces some funky bit manipulations with a much nicer call
to ethtool_link_ksettings_del_link_mode when removing link modes.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Someone left this poor little function naked with no header. This
dresses it up in a proper function header it deserves.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This 'ifdef' doesn't accomplish anything so remove it.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
After the switch to the new ethtool API, ethtool passes us
ethtool_ksettings structs instead of ethtool_command structs, however we
were still referring to them as 'cmd' variables. This renames them to
'ks' variables which makes the code easier to understand.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When using 'ethtool -L' on a VF to change number of requested queues
from PF, we shouldn't trust the VF to reset itself after making the
request. Doing it that way opens the door for a potentially malicious
VF to do nasty things to the PF which should never be the case.
This makes it such that after VF makes a successful request, PF will
then reset the VF to institute required changes. Only if the request
fails will PF send a message back to VF letting it know the request was
unsuccessful.
Testing-hints:
There should be no real functional changes. This is simply hardening
against a potentially malicious VF.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When querying the NVM for supported phy_types, on some firmware
versions, we were failing to actually fill out the phy_types which means
ethtool wouldn't report any link types.
Testing-hints:
Check 'ethtool <iface>' if you have the right (wrong?) firmware.
Without this patch, no link modes will be reported.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't populate const array patterns on the stack, instead make it
static. Makes the object code smaller by over 60 bytes:
Before:
text data bss dec hex filename
1953 496 0 2449 991 i40e_diag.o
After:
text data bss dec hex filename
1798 584 0 2382 94e i40e_diag.o
(gcc 6.3.0, x86-64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch enables setting up maximum Tx rates for the traffic
classes in i40e. The maximum rate is offloaded to the hardware through
the mqprio framework by specifying the mode option as 'channel' and
shaper option as 'bw_rlimit' and is configured for the VSI. Configuring
minimum Tx rate limit is not supported in the device. The minimum
usable value for Tx rate is 50Mbps.
Example:
# tc qdisc add dev eth0 root mqprio num_tc 2 map 0 0 0 0 1 1 1 1\
queues 4@0 4@4 hw 1 mode channel shaper bw_rlimit\
max_rate 4Gbit 5Gbit
To dump the bandwidth rates:
# tc qdisc show dev eth0
qdisc mqprio 804a: root tc 2 map 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 0
queues:(0:3) (4:7)
mode:channel
shaper:bw_rlimit max_rate:4Gbit 5Gbit
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch refactors the BW rate limiting for Tx traffic
on the VF to be reused in the next patch for rate limiting Tx
traffic for the VSIs on the PF as well.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e driver is modified to enable the new mqprio hardware
offload mode and factor the TCs and queue configuration by
creating channel VSIs. In this mode, the priority to traffic
class mapping and the user specified queue ranges are used
to configure the traffic classes by setting the mode option to
'channel'.
Example:
map 0 0 0 0 1 2 2 3 queues 2@0 2@2 1@4 1@5\
hw 1 mode channel
qdisc mqprio 8038: root tc 4 map 0 0 0 0 1 2 2 3 0 0 0 0 0 0 0 0
queues:(0:1) (2:3) (4:4) (5:5)
mode:channel
shaper:dcb
The HW channels created are removed and all the queue configuration
is set to default when the qdisc is detached from the root of the
device.
This patch also disables setting up channels via ethtool (ethtool -L)
when the TCs are configured using mqprio scheduler.
The patch also limits setting ethtool Rx flow hash indirection
(ethtool -X eth0 equal N) to max queues configured via mqprio.
The Rx flow hash indirection input through ethtool should be
validated so that it is within in the queue range configured via
tc/mqprio. The bound checking is achieved by reporting the current
rss size to the kernel when queues are configured via mqprio.
Example:
map 0 0 0 1 0 2 3 0 queues 2@0 4@2 8@6 11@14\
hw 1 mode channel
Cannot set RX flow hash configuration: Invalid argument
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch sets up the infrastructure for offloading TCs and
queue configurations to the hardware by creating HW channels(VSI).
A new channel is created for each of the traffic class
configuration offloaded via mqprio framework except for the first TC
(TC0). TC0 for the main VSI is also reconfigured as per user provided
queue parameters. Queue counts that are not power-of-2 are handled by
reconfiguring RSS by reprogramming LUTs using the queue count value.
This patch also handles configuring the TX rings for the channels,
setting up the RX queue map for channel.
Also, the channels so created are removed and all the queue
configuration is set to default when the qdisc is detached from the
root of the device.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Introduce a macro for the bit setting the PF reset flag and
update its usages. This makes it easier to use this flag
in functions to be introduced in future without encountering
checkpatch issues related to alignment and line over 80
characters.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Check memory allocation failures and return -ENOMEM in such cases, as
already done for other memory allocations in this function.
This avoids NULL pointers dereference.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Tested-by: Aaron Brown <aaron.f.brown@intel.com
Acked-by: PJ Waskiewicz <peter.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
e1000e_put_txbuf() can be called from normal reclamation path as well as
when a DMA mapping failure, so we need to differentiate these two cases
when freeing SKBs to be drop monitor friendly. e1000e_tx_hwtstamp_work()
and e1000_remove() are processing TX timestamped SKBs and those should
not be accounted as drops either.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Devices that support FLAG2_DMA_BURST have different default values
for RDTR and RADV. Apply burst mode default settings only when no
explicit value was passed at module load.
The RDTR default is zero. If the module is loaded for low latency
operation with RxIntDelay=0, do not override this value with a burst
default of 32.
Move the decision to apply burst values earlier, where explicitly
initialized module variables can be distinguished from defaults.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Intel® 100/200 Series Chipset platforms reduced the round-trip
latency for the LAN Controller DMA accesses, causing in some high
performance cases a buffer overrun while the I219 LAN Connected
Device is processing the DMA transactions. I219LM and I219V devices
can fall into unrecovered Tx hang under very stressfully UDP traffic
and multiple reconnection of Ethernet cable. This Tx hang of the LAN
Controller is only recovered if the system is rebooted. Slightly slow
down DMA access by reducing the number of outstanding requests.
This workaround could have an impact on TCP traffic performance
on the platform. Disabling TSO eliminates performance loss for TCP
traffic without a noticeable impact on CPU performance.
Please, refer to I218/I219 specification update:
https://www.intel.com/content/www/us/en/embedded/products/networking/
ethernet-connection-i218-family-documentation.html
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Reviewed-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Reviewed-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When e1000e_poll() is not fast enough to keep up with incoming traffic, the
adapter (when operating in msix mode) raises the Other interrupt to signal
Receiver Overrun.
This is a double problem because 1) at the moment e1000_msix_other()
assumes that it is only called in case of Link Status Change and 2) if the
condition persists, the interrupt is repeatedly raised again in quick
succession.
Ideally we would configure the Other interrupt to not be raised in case of
receiver overrun but this doesn't seem possible on this adapter. Instead,
we handle the first part of the problem by reverting to the practice of
reading ICR in the other interrupt handler, like before commit 16ecba59bc
("e1000e: Do not read ICR in Other interrupt"). Thanks to commit
0a8047ac68 ("e1000e: Fix msi-x interrupt automask") which cleared IAME
from CTRL_EXT, reading ICR doesn't interfere with RxQ0, TxQ0 interrupts
anymore. We handle the second part of the problem by not re-enabling the
Other interrupt right away when there is overrun. Instead, we wait until
traffic subsides, napi polling mode is exited and interrupts are
re-enabled.
Reported-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Fixes: 16ecba59bc ("e1000e: Do not read ICR in Other interrupt")
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Lennart reported the following race condition:
\ e1000_watchdog_task
\ e1000e_has_link
\ hw->mac.ops.check_for_link() === e1000e_check_for_copper_link
/* link is up */
mac->get_link_status = false;
/* interrupt */
\ e1000_msix_other
hw->mac.get_link_status = true;
link_active = !hw->mac.get_link_status
/* link_active is false, wrongly */
This problem arises because the single flag get_link_status is used to
signal two different states: link status needs checking and link status is
down.
Avoid the problem by using the return value of .check_for_link to signal
the link status to e1000e_has_link().
Reported-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
All the helpers return -E1000_ERR_PHY.
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reading e1000e_check_for_copper_link() shows that get_link_status is set to
false after link has been detected. Therefore, it stays TRUE until then.
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In case of error from e1e_rphy(), the loop will exit early and "success"
will be set to true erroneously.
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It looks like we weren't correctly placing the pages from buffers that had
been used to return a filter programming status back on the ring. As a
result they were being overwritten and tracking of the pages was lost.
This change works to correct that by incorporating part of
i40e_put_rx_buffer into the programming status handler code. As a result we
should now be correctly placing the pages for those buffers on the
re-allocation list instead of letting them stay in place.
Fixes: 0e626ff7cc ("i40e: Fix support for flow director programming status")
Reported-by: Anders K. Pedersen <akp@cohaesio.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Anders K Pedersen <akp@cohaesio.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Caller needs to acquire the lock. Called functions will not.
Fixes: 09f79fd49d ("i40e: avoid NVM acquire deadlock during NVM update")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2017-10-09
This series contains updates to i40e and i40evf only.
Jake fixes missed flag conversion from u64 to u32. Fixes a deafult ITR
value issue where the driver defaults to an ITR value of half the
expected value (in terms of minimum microseconds between interrupts). So
fix this by changing the default values to be calculated using the
ITR_REG_TO_USEC() macro which indicates that we are converting from the
register units into microseconds. Updates the drivers to bump the tail in
increments of 8 and double the number of descriptors we will bundle into
one tail bump when receiving. With the recent kernel support for
enabling XPS and QoS at the same time, we no longer need to worry about
the number of traffic classes when enabling XPS.
Lihong converts the use of hash_for_each() to hash_for_each_safe() to
safely remove a hash entry. Adds a check for the return value for
find_first_bit() in the case that it returns the size passed to search.
Alan fixes a bug in which filters are erroneously removed if they are
removed and then added again. So make sure that when adding a filter, if
we find it already existed in our list, make sure it is not marked to be
removed.
Jayaprakash adds the retrying of PHY reads when the I2C is busy for a
maximum period of 500ms.
Rami fixes code comment typo.
Stefano Brivio simplifies the code by removing the use of a local
return code variable and simply return the results of the read function.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a typo in i40e_vsi_alloc_arrays() documentation.
The first parameter name should be "vsi" instead of "type".
Signed-off-by: Rami Rosen <rami.rosen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The computed result of I40E_MAX_VSI_QP * I40E_VIRTCHNL_SUPPORTED_QTYPES
is used more than three times in function i40e_config_irq_link_list.
Simply declare a local variable to store it to improve readability.
Signed-off-by: Lihong Yang <lihong.yang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
- When the I2C is busy, the PHY reads are delayed. The firmware will
return EGAIN in these cases with an expectation that the SW will
trigger the reads again
- This patch retries the operation for a maximum period of 500ms
Signed-off-by: Jayaprakash Shanmugam <jayaprakash.shanmugam@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The find_first_bit function will return the size passed to search
if the first set bit is not found. This patch adds the check in case
that happens as the return value would be used as the index in an array
and that would have caused the out-of-bounds access.
Detected by CoverityScan, CID 1295969 Out-of-bounds access
Signed-off-by: Lihong Yang <lihong.yang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Recently, the kernel gained support for enabling XPS and QoS at the
same time. Thus, we no longer need to worry about the number of
traffic classes when enabling XPS.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Double the number of descriptors we'll bundle into one tail bump when
receiving. Empirical testing has shown that we reduce CPU utilization
and don't appear to reduce throughput or packet rate. 32 seems to be the
sweet spot, as it's half the default polling budget, so we'd essentially
reduce from 4 tail writes when polling down to 2. Increasing this up to
64 appears to have negative impacts as it may become possible that we
don't bump the tail each time we get polled, which could cause a long
delay between returning descriptors to the hardware.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Hardware only fetches descriptors on cachelines of 8, essentially
ignoring the lower 3 bits of the tail register. Thus, it is pointless to
bump tail by an unaligned access as the hardware will ignore some of the
new descriptors we allocated. Thus, it's ideal if we can ensure tail
writes are always aligned to 8.
At first, it seems like we'd already do this, since we allocate
descriptors in batches which are a multiple of 8. Since we'd always
increment by a multiple of 8, it seems like the value should always be
aligned.
However, this ignores allocation failures. If we fail to allocate
a buffer, our tail register will become unaligned. Once it has become
unaligned it will essentially be stuck unaligned until a buffer
allocation happens to fail at the exact amount necessary to re-align it.
We can do better, by simply rounding down the number of buffers we're
about to allocate (cleaned_count) such that "next_to_clean
+ cleaned_count" is rounded to the nearest multiple of 8.
We do this by calculating how far off that value is and subtracting it
from the cleaned_count. This essentially defers allocation of buffers if
they're going to be ignored by hardware anyways, and re-aligns our
next_to_use and tail values after a failure to allocate a descriptor.
This calculation ensures that we always align the tail writes in a way
the hardware expects and don't unnecessarily allocate buffers which
won't be fetched immediately.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The lrxq thresh value tells hardware to immediately interrupt when there
are fewer than N*64 packets left in the ring.
Counter intuitively, empirical testing has shown that decreasing this
value from 2 to 1, and thus changing from an immediate interrupt at
fewer than 128 descriptors down to 64 descriptors causes a small
increase in the maximum total packets per second we can receive. This
increase occurs even when we're polling with interrupts masked, as the
hardware must still handle interrupts internally even if we've disabled
them in software.
Also reduce the value for any VFs we allocate.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the past we changed driver behavior to not clear the PBA when
re-enabling interrupts. This change was motivated by the flawed belief
that clearing the PBA would cause a lost interrupt if a receive
interrupt occurred while interrupts were disabled.
According to empirical testing this isn't the case. Additionally, the
data sheet specifically says that we should set the CLEARPBA bit when
re-enabling interrupts in a polling setup.
This reverts commit 40d72a5098 ("i40e/i40evf: don't lose interrupts")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ITR register expects to be programmed in units of 2 microseconds.
Because of this, all of the drivers I40E_ITR_* constants are in terms of
this 2 microsecond register.
Unfortunately, the rx_itr_default value is expected to be programmed in
microseconds.
Effectively the driver defaults to an ITR value of half the expected
value (in terms of minimum microseconds between interrupts).
Fix this by changing the default values to be calculated using
ITR_REG_TO_USEC macro which indicates that we're converting from the
register units into microseconds.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Due to the asynchronous nature in which mac filters are added and
deleted, there exists a bug in which filters are erroneously removed if
removed then added again quickly.
The events are as such:
- filter marked for removal
- same filter is re-added before watchdog that cleans up filters
- we skip re-adding the filter because we have it already in the
list
- watchdog filter cleanup kicks off and filter is removed
So when we were re-adding the same filter, it didn't actually get added
because it already existed in the list, but was marked for removal and
had yet to actually be removed.
This patch fixes the issue by making sure that when adding a filter, if
we find it already existing in our list, make sure it is not marked to
be removed.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch replaces hash_for_each function with hash_for_each_safe
when calling __i40e_del_filter. The hash_for_each_safe function is
the right one to use when iterating over a hash table to safely remove
a hash entry. Otherwise, incorrect values may be read from freed memory.
Detected by CoverityScan, CID 1402048 Read from pointer after free
Signed-off-by: Lihong Yang <lihong.yang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since we don't yet have more than 32 flags, we'll use a u32 for both the
hw_features and flag field. Should we gain more flags in the future, we
may need to convert to a u64 or separate flags out into two fields.
This was overlooked in the previous commit 2781de2134c4 ("i40e/i40evf:
organize and re-number feature flags"), where the feature flag was not
converted form u64 to u32.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In case where AER recovery fails the device is left in a down state.
Consecutive AER error injection can lead to a double IRQ free.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The following change is meant to update the adaptive ITR algorithm to
better support the needs of the network. Specifically with this change what
I have done is make it so that our ITR algorithm will try to prevent either
starving a socket buffer for memory in the case of Tx, or overrunning an Rx
socket buffer on receive.
In addition a side effect of the calculations used is that we should
function better with new features such as XDP which can handle small
packets at high rates without needing to lock us into NAPI polling mode.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bits other than FWSM.PT can be set in IXGBE_SWFW_MODE_MASK making the
previous check invalid.
Change the check for MNG present to be only based on FWSM.PT bit.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is resolving Coverity hits where padding in a structure could
be used uninitialized.
- Initialize fwd_cmd.pad/2 before ixgbe_calculate_checksum()
- Initialize buffer.pad2/3 before ixgbe_hic_unlocked()
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ixgbe driver have page recycle scheme based around the RX-ring
queue, where a RX page is shared between two packets. Based on the
refcnt, the driver can determine if the RX-page is currently only used
by a single packet, if so it can then directly refill/recycle the
RX-slot by with the opposite "side" of the page.
While this is a clever trick, it is hard to determine when this
recycling is successful and when it fails. Adding a counter, which is
available via ethtool --statistics as 'alloc_rx_page'. Which counts
the number of times the recycle fails and the real page allocator is
invoked. When interpreting the stats, do remember that every alloc
will serve two packets.
The counter is collected per rx_ring, but is summed and ethtool
exported as 'alloc_rx_page'. It would be relevant to know what
rx_ring that cannot keep up, but that can be exported later if
someone experience a need for this.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit: fed21bcee7a5
("ixgbe: Don't bother clearing buffer memory for descriptor rings)
exposed some issues with the logic in the current implementation of
ixgbe_clean_test_rings() that are being addressed in this patch:
- Split the clearing of the Tx and Rx rings in separate loops. Previously
both Tx and Rx rings were cleared in a rx_desc->wb.upper.length based
loop which could lead to issues if for w/e reason packets were received
outside of the frames transmitted for the loopback test.
- Add check for IXGBE_TXD_STAT_DD to avoid clearing the rings if the
transmits have not comlpeted by the time we enter ixgbe_clean_test_rings()
- Exit early on ixgbe_check_lbtest_frame() failure.
This change fixes a crash during ethtool diagnostic (ethtool -t).
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Ignoring errors when attempting to identify the PHY can lead to a crash.
Specifically in the case of FW controlled PHYs where the PHY read/write
operations are set to NULL.
Removed redundant comment.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Just like when the last VF is removed, we need to restore normal
operations after the last macvlan offload is removed, else we
get stuck in single queue operations.
To test:
ethtool -l eth1 # note the number of queues in use, ~= cpus
ethtool -K eth1 l2-fwd-offload on
ip link add mv1 link eth1 type macvlan mode bridge
ip link set dev mv1 up
ip link del mv1
ethtool -l eth1 # are we back to the same # of queues, or stuck on 1?
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Declare ixgbe_mac_operations structures as const as they are only stored
in the mac_ops field of ixgbe_info structure. This field is of type
const and therefore ixgbe_mac_operations structure can be made const
too.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Added clearing of SW resource bits in the SW/FW synchronization
register to ixgbe_init_swfw_sync_X540().
Updated ixgbe_acquire_swfw_sync_X540 SW Manageability host interface
resource bit error case to match the error handling of the other SW
resource bits. Which is to release the SW resource bits if SW times
out while attempting to acquire the resource.
This allows the driver to load in cases where the semaphore bits
could be stuck after a reset or a crash.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Changing the TX ring parameters with an XDP program attached may
cause the XDP queues to be cleared and the TX rings to be incorrectly
configured.
Fix by doing correct ring accounting in setup call.
Fixes: 33fdc82f08 ("ixgbe: add support for XDP_TX action")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ixgbe driver use the compile check to determine if it can
send TLPs to Root Port with the Relaxed Ordering Attribute set,
this is too inconvenient, now the new flag PCI_DEV_FLAGS_NO_RELAXED_ORDERING
has been added to the kernel and we could check the bit4 in the PCIe
Device Control register to determine whether we should use the Relaxed
Ordering Attributes or not, so use this new way in the ixgbe driver.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Acked-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The new flag PCI_DEV_FLAGS_NO_RELAXED_ORDERING has been added
to indicate that Relaxed Ordering Attributes (RO) should not
be used for Transaction Layer Packets (TLP) targeted toward
these affected Root Port, it will clear the bit4 in the PCIe
Device Control register, so the PCIe device drivers could
query PCIe configuration space to determine if it can send
TLPs to Root Port with the Relaxed Ordering Attributes set.
With this new flag we don't need the config ARCH_WANT_RELAX_ORDER
to control the Relaxed Ordering Attributes for the ixgbe drivers
just like the commit 1a8b6d76dc ("net:add one common config...") did,
so revert this commit.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In ixgbe_clear_udp_tunnel_port(), we read the IXGBE_VXLANCTRL register
and then try to mask some bits out of the value, using the logical
instead of bitwise and operator.
Fixes: a21d0822ff ("ixgbe: add support for geneve Rx offload")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In cases where PHY register access is not supported, don't mislead
a caller into thinking that it is supported by returning a PHY
address. Instead, return -EOPNOTSUPP when PHY access is not
supported.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that we've reduced the number of flags, organize similar flags
together and re-number them accordingly.
Since we don't yet have more than 32 flags, we'll use a u32 for both the
hw_features and flag field. Should we gain more flags in the future, we
may need to convert to a u64 or separate flags out into two fields.
One alternative approach considered, but not implemented here, was to
use an enumeration for the flag variables, and create a macro
I40E_FLAG() which used string concatenation to generate BIT_ULL values.
This has the advantage of making the actual bit values compile-time
dynamic so that we do not need to worry about matching the order to the
bit value. However, this does produce a high level of code churn, and
makes it more difficult to read a dumped flags value when debugging.
Change-ID: I8653fff69453cd547d6fe98d29dfa9d8710387d1
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since commit 6a7fded776 ("i40e: Fix RS bit update in Tx path and
disable force WB workaround") we've tried to "optimize" setting the
RS bit based around skb->xmit_more. This same logic was refactored
in commit 1dc8b53879 ("i40e: Reorder logic for coalescing RS bits"),
but ultimately was not functionally changed.
Using skb->xmit_more in this way is incorrect, because in certain
circumstances we may see a large number of skbs in sequence with
xmit_more set. This leads to a performance loss as the hardware does not
writeback anything for those packets, which delays the time it takes for
us to respond to the stack transmit requests. This significantly impacts
UDP performance, especially when layered with multiple devices, such as
bonding, VLANs, and vnet setups.
This was not noticed until now because it is difficult to create a setup
which reproduces the issue. It was discovered in a UDP_STREAM test in
a VM, connected using a vnet device to a bridge, which is connected to
a bonded pair of X710 ports in active-backup mode with a VLAN. These
layered devices seem to compound the number of skbs transmitted at once
by the qdisc. Additionally, the problem can be masked by reducing the
ITR value.
Since the original commit does not provide strong justification for this
RS bit "optimization", revert to the previous behavior of setting the RS
bit every 4th packet.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A recent commit 809481484e5d ("i40e/i40evf: support for VF VLAN tag
stripping control") added support for VFs to negotiate the control of
VLAN tag stripping. This should have allowed VFs to disable the feature.
Unfortunately, the flag was set only in netdev->feature flags and not in
netdev->hw_features.
This ultimately causes the stack to assume that it cannot change the
flag, so it was unchangeable and marked as [fixed] in the ethtool -k
output.
Fix this by setting the feature in hw_features first, just as we do for
the PF code. This enables ethtool -K to disable the feature correctly,
and fully enables user control of the VLAN tag stripping feature.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previous implementation of LED set/get functions required to enter
PHY debug mode, in order to prevent access to it from FW and SW at
the same time. Reset of all ports was a unwanted side effect.
Signed-off-by: Mariusz Stachura <mariusz.stachura@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch implements the PCI error handler reset_prepare and reset_done.
This allows us to handle function level reset. Without this patch we
are unable to perform and recover from an FLR correctly and this will cause
VFs to be unable to recover from an FLR on the PF.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When there is no space for more flow director filters and user requested to
add a new one it is rejected by firmware and automatically removed from the
filter list maintained by driver. This behaviour is correct. Afterwards
existing filter can be removed making free slot for the new one. This
however causes the newly added filter to be accepted by firmware but
removed from driver filter list resulting in not showing after issuing
'ethtool -n <dev_name>'.
This happened due to not clearing the variable pf->fd_inv which stores
filter number to be removed from the list when firmware refused to add the
requested filter. It caused the filter with this specific ID to be
constantly removed once it was added to the list although it has been
accepted by firmware and effectively applied to the NIC.
It was fixed by clearing pf->fd_inv variable after removal of the filter
from the list when it was rejected by firmware.
Signed-off-by: Filip Sadowski <filip.sadowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch causes error message to be displayed when NIC detects
insertion of module that does not meet thermal requirements.
Signed-off-by: Filip Sadowski <filip.sadowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes some code that was accidentally added to
the wrong function with a merge error. Fixes: c53934c6d1
("i40e: fix: do not sleep in netdev_ops")
Signed-off-by: Alice Michael <alice.michael@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When using set_bit and friends, we should be using actual
bitmaps, and fix all the locations where we might access
it.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This register was defined incorrectly. Fix the increment value to 8, and
replace the iterator with _i to make the definition consistent with
other statistics registers.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since I40E_PHY_TYPE_MAX is used as an iterator, usually combined with
some sort of bit-shifting, it should only include actual PHY types and
not error cases. Move it up in the enum declaration so that loops only
iterate across valid PHY types.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Starting with XL710 FW 5.3 PTP L4 was disabled for XL710 due to a bug. The
bug has since been resolved in XL710 FW >6.0 and PTP L4 can now be
re-enabled on those devices with updated firmware.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently, when setting up the IRQ for a q_vector, we set an affinity
hint based on the v_idx of that q_vector. Meaning a loop iterates on
v_idx, which is an incremental value, and the cpumask is created based
on this value.
This is a problem in systems with multiple logical CPUs per core (like in
simultaneous multithreading (SMT) scenarios). If we disable some logical
CPUs, by turning SMT off for example, we will end up with a sparse
cpu_online_mask, i.e., only the first CPU in a core is online, and
incremental filling in q_vector cpumask might lead to multiple offline
CPUs being assigned to q_vectors.
Example: if we have a system with 8 cores each one containing 8 logical
CPUs (SMT == 8 in this case), we have 64 CPUs in total. But if SMT is
disabled, only the 1st CPU in each core remains online, so the
cpu_online_mask in this case would have only 8 bits set, in a sparse way.
In general case, when SMT is off the cpu_online_mask has only C bits set:
0, 1*N, 2*N, ..., C*(N-1) where
C == # of cores;
N == # of logical CPUs per core.
In our example, only bits 0, 8, 16, 24, 32, 40, 48, 56 would be set.
Instead, we should only assign hints for CPUs which are online. Even
better, the kernel already provides a function, cpumask_local_spread()
which takes an index and returns a CPU, spreading the interrupts across
local NUMA nodes first, and then remote ones if necessary.
Since we generally have a 1:1 mapping between vectors and CPUs, there
is no real advantage to spreading vectors to local CPUs first. In order
to avoid mismatch of the default XPS hints, we'll pass -1 so that it
spreads across all CPUs without regard to the node locality.
Note that we don't need to change the q_vector->affinity_mask as this is
initialized to cpu_possible_mask, until an actual affinity is set and
then notified back to us.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
By default, our devices do source pruning, that is, they drop receive
packets that have the source MAC matching one of the receive filters.
Unfortunately, this breaks ARP monitoring in channel bonding, as the
bonding driver expects devices to receive ARPs containing their own
source address.
Add an ethtool private flag to control this feature.
Also, remove the netif_running() check when we process our private
flags. It's OK to reset when the device is closed and in most cases we
need the reset the apply these changes.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a typo in i40e_pf object documentation; num_req_vfs
refers to the number of VFs requested for the PF.
Signed-off-by: Rami Rosen <rami.rosen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We've had support for setting both a minimum and maximum bandwidth via
.ndo_set_vf_bw since commit 883a9ccbae ("fm10k: Add support for SR-IOV
to driver", 2014-09-20).
Likely because we do not support minimum rates, the declaration
mis-ordered the "unused" parameter, which causes warnings when analyzed
with cppcheck.
Fix this warning by properly declaring the min_rate and max_rate
variables in the declaration and definition (rather than using
"unused"). Also rename "rate" to max_rate so as to clarify that we only
support setting the maximum rate.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't hard code the function names in the diagnostic output when these
reset related routines fail. Instead, use %s and __func__ so that future
refactors don't need to change the print outs.
Additionally, while we are here, add missing function header comments
for the new reset_prepare and reset_done function handlers.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Correct the backward logic using !net_ratelimit()
Miscellanea:
o Add a blank line before the error return label
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that we have a working MAC/VLAN queue for handling MAC/VLAN messages
from the netdev, replace the default handler for the VF<->PF messages.
This new handler is very similar to the default code, but uses the
MAC/VLAN queue instead of sending the message directly. Unfortunately we
can't easily re-use the default code, so we'll just replace the entire
function.
This ensures that a VF requesting a large number of VLANs or MAC
addresses does not start a reset cycle, as explained in the commit which
introduced the message queue.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Ngai-mint Kwan <ngai-mint.kwan@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Under some circumstances, when dealing with a large number of MAC
address or VLAN updates at once, the fm10k driver, particularly the VFs
can overload the mailbox with too many messages at once.
This results in a mailbox timeout, which causes the driver to initiate
a reset. During the reset, we re-send all the same messages that
originally caused the timeout. This results in a cycle of resets each
triggering a future reset.
To fix or avoid this, we introduce a workqueue item which monitors
a queue of MAC and VLAN requests. These requests are queued to the end
of the list, and we process as a FIFO periodically.
Initially we only handle requests for the netdev, but we do handle
unicast MAC addresses, multicast MAC addresses, and update VLAN
requests.
A future patch will add support to use this queue for handling MAC
update requests from the VF<->PF mailbox.
The MAC/VLAN work item will keep checking to make sure that each request
does not overflow the mailbox and cause a timeout. If it might, then the
work item will reschedule itself a short time later. This avoids any
reset cycle, since we never send the message if the mailbox is not
ready.
As an alternative, we tried increasing the mailbox message FIFO, but
this just delays the problem and results in needless memory waste on the
system. Our new message queue is dynamically allocated so only uses as
much memory as it needs. Additionally, it need not be contiguous like
the Tx and Rx FIFOs.
Note that this patch chose to only create a queue for MAC and VLAN
messages, since these are the only messages sent in a large enough
volume to cause the reset loop. Other messages are very unlikely to
overflow the mailbox Tx FIFO so easily.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Replace the PCI specific legacy power management hooks with the new
generic power management hooks which work properly for both suspend and
hibernate. The new generic system is better and properly handles the
lower level PCIe power management rather than forcing the driver to
handle it.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Lets not re-invent the locking wheel. Remove our bitlock and use
a proper spinlock instead.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If we lose PCIe link, such as when an unannounced PFLR event occurs, or
when a device is surprise removed, we currently detach the device and
close the netdev. This unfortunately leaves a lot of things still
active, such as the msix_mbx_pf IRQ, and Tx/Rx resources.
This can cause problems because the register reads will return
potentially invalid values which may result in unknown driver behavior.
Begin the process of resetting using fm10k_prepare_for_reset(), much in
the same way as the suspend and resume cycle does. This will attempt to
shutdown as much as possible, in order to prevent possible issues.
A naive implementation for this has issues, because there are now
multiple flows calling the reset logic and setting a reset bit. This
would cause problems, because the "re-attach" routine might call
fm10k_handle_reset() prior to the reset actually finishing. Instead,
we'll add state bits to indicate which flow actually initiated the
reset.
For the general reset flow, we'll assume that if someone else is
resetting that we do not need to handle it at all, so it does not need
its own state bit. For the suspend case, we will simply issue a warning
indicating that we are attempting to recover from this case when
resuming.
For the detached subtask, we'll simply refuse to re-attach until we've
actually initiated a reset as part of that flow.
Finally, we'll stop attempting to manage the mailbox subtask when we're
detached, since there's nothing we can do if we don't have a PCIe
address.
Overall this produces a much cleaner shutdown and recovery cycle for
a PCIe surprise remove event.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2017-10-02
This series contains updates to i40e and i40evf.
Shannon Nelson fixes an issue where when a machine has more CPUs than
queue pairs, the counting gets a "little funky" and turns off Flow
Director. So to correct it, limit the number of LAN queues initially
allocated to be sure there are some left for Flow Director and other
features.
Lihong cleans up dead code by removing a condition check which cannot
ever be true.
Christophe Jaillet fixes a potential NULL pointer dereference, which
could happen if kzalloc() fails.
Filip corrects the reporting of supported link modes, which was incorrect
for some NICs. Added support for 'ethtool -m' command, which displays
information about QSFP+ modules.
Mariusz adds functions to read/write the LED registers to control the
LEDS, instead of accessing the registers directly whenever the LEDs
need to be controlled.
Jake fixes a regression where we introduced a scheduling while atomic,
so introduce a separate helper function which will manage its own need
for the mac_filter_hash_lock. Also cleaned up the "PF" parameter in
i40e_vc_disable_vf() since it is never used and is not needed. Fixed
a rare case where it is possible that a reset does not occur when
i40e_vc_disable_vf() is called, so modify i40e_reset_vf() to return a
bool to indicate whether it reset or not so that i40e_vc_disable_vf()
can wait until a reset actually occurs.
Alan adds the ability for the VF to request more or less underlying
allocated queues from the PF. Fixes the incorrect method for clearing
the vf_states variable with a NULL assignment, when we should be
using atomic bitops since we don't actually want to clear all the
flags. Fixed a resource leak, where the PF driver fails to inform
clients of a VF reset because we were incorrectly checking the
I40E_VF_STATE_PRE_ENABLE bit.
Mitch converts i40evf_map_rings_to_vectors() to a void function since
it cannot fail and allows us to clean up the checks for the function
return value.
Scott enables the driver(s) to pass traffic with VLAN tags using the
802.1ad Ethernet protocol.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable i40e to pass traffic with VLAN tags using the 802.1ad ethernet
protocol ID (0x88a8).
This requires NIC firmware providing version 1.7 of the API. With
older NIC firmware 802.1ad tagged packets will continue to be dropped.
No VLAN offloads nor RSS are supported for 802.1ad VLANs.
Signed-off-by: Scott Peterson <scott.d.peterson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently there is a bug in which the PF driver fails to inform clients
of a VF reset which then causes clients to leak resources. The bug
exists because we were incorrectly checking the I40E_VF_STATE_PRE_ENABLE
bit.
When a VF is first init we go through a reset to initialize variables
and allocate resources but we don't want to inform clients of this first
reset since the client isn't fully enabled yet so we set a state bit
signifying we're in a "pre-enabled" client state. During the first
reset we should be clearing the bit, allowing all following resets to
notify the client of the reset when the bit is not set. This patch
fixes the issue by negating the 'test_and_clear_bit' check to accurately
reflect the behavior we want.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently we inappropriately clear the vf_states variable with a null
assignment. This is problematic because we should be using atomic
bitops on this variable and we don't actually want to clear all the
flags. We should just clear the ones we know we want to clear.
Additionally remove the I40E_VF_STATE_FCOEENA bit because it is no
longer being used.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This function cannot fail, so why is it returning a value? And why are
we checking it? Why shouldn't we just make it void? Why is this commit
message made up of only questions?
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the VF gets a default number of allocated queues from HW on
init and it could choose to enable or disable those allocated queues.
This makes it such that the VF can request more or less underlying
allocated queues from the PF.
First the VF negotiates the number of queues it wants that can be
supported by the PF and if successful asks for a reset. During reset
the PF will reallocate the HW queues for the VF and will then remap the
new queues.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It is possible although rare that we may not reset when
i40e_vc_disable_vf() is called. This can lead to some weird
circumstances with some values not being properly set. Modify
i40e_reset_vf() to return a code indicating whether it reset or not.
Now, i40e_vc_disable_vf() can wait until a reset actually occurs. If it
fails to free up within a reasonable time frame we'll display a warning
message.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Replace i40e_vc_notify_vf_reset and i40e_reset_vf with a call to
i40e_vc_disable_vf which does this exact thing. This matches similar
code patterns throughout the driver.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It's never used, and the vf structure could get back to the PF if
necessary. Lets just drop the extra unneeded parameter.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When we refactored handling of the PVID in commit 9af52f60b2
("i40e: use (add|rm)_vlan_all_mac helper functions when changing PVID")
we introduced a scheduling while atomic regression.
This occurred because we now held the spinlock across a call to
i40e_reset_vf(), which results in a usleep_range() call that triggers
a scheduling while atomic bug. This was rare as it only occurred if the
user configured a VLAN on a VF and also attempted to reconfigure the VF
from the host system with a port VLAN.
We do need to hold the lock while calling i40e_is_vsi_in_vlan(), but we
should not be holding it while we reset the VF.
We'll fix this by introducing a separate helper function
i40e_vsi_has_vlans which checks whether we have a PVID and whether the
VSI has configured VLANs. This helper function will manage its own need
for the mac_filter_hash_lock.
Then, we can move the acquiring of the spinlock until after we reset the
VF, which ensures that we do not sleep while holding the lock.
Using a separate function like this makes the code more clear and is
easier to read than attempting to release and re-acquire the spinlock
when we reset the VF.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of accessing register directly, use newly added AQC in
order to blink LEDs. Introduce and utilize a new flag to prevent
excessive API version checking.
Signed-off-by: Mariusz Stachura <mariusz.stachura@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for 'ethtool -m' command which displays
information about (Q)SFP+ module plugged into NIC's cage.
Signed-off-by: Filip Sadowski <filip.sadowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes incorrect reporting of supported link modes on some NICs.
Signed-off-by: Filip Sadowski <filip.sadowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
