[WHY]
Logging for SMU response value after the wait allows us to know
immediately what the response value was. Makes it easier to debug should
the value be anything other than OK.
[HOW]
Using the the already available DC SMU logging functions.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Saaem Rizvi <SyedSaaem.Rizvi@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
For VG, we want to turn off power/backlight of the intenral panel when
plugging in external monitor and going to "external monitor only" mode.
[how]
For turning off power of the internal panel, ignore the config flag whic
bypasses power sequencing for eDP panels.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Sung Joon Kim <sungkim@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Only on VG, if external display is disconnected during S3 suspend, the
internal panel doesn't light up on resume because we set the power state
using an unsupported DPCD register SET_POWER. To check the register is
supported, we need to check SET_POWER_CAPABLE first which is
eDP-specific DPCD register field.
[how]
Check the SET_POWER_CAPABLE register field and decide the control of the
eDP power state based on the read register value.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Agustin Gutierrez <Agustin.Gutierrez@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Sung Joon Kim <sungkim@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
when connect one 4k@144hz dp to dsc mst hub, 4k@144hz mode is in valid
mode list. but some mst hub port output bandwidth does not support
4k@144hz.
[How]
add mst port output bandwidth checks, include full_pbn, branch max
throughput mps.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Jerry Zuo <Jerry.Zuo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: hersen wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
While updating the config of hdcp, we use the sink_singal type of the
dc_sink to decide the HDCP operation mode. However, it doesn't consider
the case when the sink is a emulated one.
[How]
Take dc_em_sink into account while updating HDCP config.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Aurabindo Jayamohanan Pillai <Aurabindo.Pillai@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Observe that we have several problems while releasing remote dc_sink
under mst cases.
- When unplug mst branch device from the source, we now try to free all
remote dc_sinks in dm_helpers_dp_mst_stop_top_mgr(). However, there are
bugs while we're releasing dc_sinks here. First of all,
link->remote_sinks[] array get shuffled within
dc_link_remove_remote_sink(). As the result, increasing the array index
within the releasing loop is wrong. Secondly, it tries to call
dc_sink_release() to release the dc_sink of the same aconnector every
time in the loop. Which can't release dc_sink of all aconnector in the
mst topology.
- There is no code path for us to release remote dc_sink for disconnected
sst monitor which unplug event is notified by CSN sideband message. Which
means we'll use stale dc_sink data to represent later on connected
monitor. Also, has chance to break the maximum remote dc_sink number
constraint.
[How]
Distinguish unplug event of mst scenario into 2 cases.
* Unplug sst/legacy stream sink off the mst topology
- Release related remote dc_sink in detec_ctx().
* Unplug mst branch device off the mst topology
- Release related remote dc_sink in early_unregister()
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Aurabindo Jayamohanan Pillai <Aurabindo.Pillai@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 3c4d55c9b9.
Revert the commit because:
- It's incomplete of the function dm_set_dpms_off() for mst case. For
stream sinks whithin the same mst topology, they share the same dc_link.
dm_set_dpms_off() tries to update one mst stream only which is
incomplete.
- Setting dpms off should be triggered by usermode. Besdies, it seems
usermode does release relevant resource for mst & non-mst case when
unplug connecotr now.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Aurabindo Jayamohanan Pillai <Aurabindo.Pillai@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 035f54969b.
The reverted commit was trying to fix side effect brought by
commit 3c4d55c9b9 ("drm/amd/display: turn DPMS off on connector unplug")
However,
* This reverted commit will have mst case never call dm_set_dpms_off()
which conflicts the idea of original commit 3c4d55c9b9 ("drm/amd/display: turn DPMS off on connector unplug")
That's due to dm_crtc_state is always null since the input parameter
aconnector is the root device (source) of mst topology. It's not an
end stream sink within the mst topology.
* Setting dpms off should be triggered by usermode. Besdies, it seems
usermode does release relevant resource for mst & non-mst case when
unplug connecotr now. Which means we no longer need both commits now:
commit 3c4d55c9b9 ("drm/amd/display: turn DPMS off on connector unplug")
commit 035f54969b ("drm/amd/display: Add flag to detect dpms force off during HPD")
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Aurabindo Jayamohanan Pillai <Aurabindo.Pillai@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
A variety of Lenovo machines with Rembrandt APUs and OLED panels have
stopped showing the display at login. This behavior clears up after
leaving it idle and moving the mouse or touching keyboard.
It was bisected to be caused by commit 559e265522 ("drm/amd/display:
keep eDP Vdd on when eDP stream is already enabled"). Revert this commit
to fix the issue.
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2047
Reported-by: Aaron Ma <aaron.ma@canonical.com>
Fixes: 559e265522 ("drm/amd/display: keep eDP Vdd on when eDP stream is already enabled")
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Tested-by: Mark Pearson <markpearson@lenovo.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Some APUs with SMU13 are showing the following message:
`amdgpu 0000:63:00.0: amdgpu: Unexpected and unhandled version: 3.1`
This warning isn't relevant for smu info 3.1, as no bootup information
is present in the table.
Fixes: 593a54f180 ("drm/amd/pm: correct the way for retrieving bootup clocks")
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
set mp1 unload state will cause the SMC FW can't accept any SMU message,
skip to set mp1 unload state to avoid following case fail:
- runtime pm case.
- gpu reset case.
Fixes: 72aeb6ee0c ("drm/amd/pm: fix driver reload SMC firmware fail issue for smu13")
Signed-off-by: Yang Wang <KevinYang.Wang@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The EccInfo_t struct in driver_if.h is as below in official release
verion 68.55.0
typedef struct {
uint64_t mca_umc_status;
uint64_t mca_umc_addr;
uint16_t ce_count_lo_chip;
uint16_t ce_count_hi_chip;
uint32_t eccPadding;
uint64_t mca_ceumc_addr;
} EccInfo_t;
It's different from the debug version druing develop print correctable
error address, so adjust EccInfo_t struct.
Signed-off-by: Stanley.Yang <Stanley.Yang@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Certain GL unit tests for large textures can cause problems
with the OOM killer since there is no way to link this memory
to a process. This was originally mitigated (but not necessarily
eliminated) by limiting the GTT size. The problem is this limit
is often too low for many modern games so just make the limit 1/2
of system memory. The OOM accounting needs to be addressed, but
we shouldn't prevent common 3D applications from being usable
just to potentially mitigate that corner case.
Set default GTT size to max(3G, 1/2 of system ram) by default.
v2: drop previous logic and default to 3/4 of ram
v3: default to half of ram to align with ttm
v4: fix spelling in comment (Kent)
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1942
Reviewed-by: Marek Olšák <marek.olsak@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Loop through all VMIDs for gmc_v10_0_flush_gpu_tlb_pasid and
gmc_v11_0_flush_gpu_tlb_pasid (only if using MES for gmc_v10). This is
required for MES due to use_different_vmid_compute causing SDMA queues
to be assigned different VMIDs than compute for the same PASID.
Signed-off-by: Graham Sider <Graham.Sider@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Drive-by cleanup, we don't need to validate the port references here as we
already previously went through the effort of refactoring things such that
we're guaranteed to be able to access ->mstb and ->port safely from
drm_dp_check_and_send_link_address(), since the only two places in the
codebase that drop an MST reference in such a way that it would remove it
from the topology are both protected under probe_lock.
Thanks for that, past Lyude!
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Wayne Lin <Wayne.Lin@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220602201757.30431-2-lyude@redhat.com
This implements the callback added by the patch ("drm/dp: Add
wait_hpd_asserted() callback to struct drm_dp_aux").
With this change and all the two "DP AUX Endpoint" drivers changed to
use wait_hpd_asserted(), we no longer need to have an long delay in
the AUX transfer function. It's up to the panel code to make sure that
the panel is powered now. If someone tried to call the aux transfer
function without making sure the panel is powered we'll just get a
normal transfer failure.
We'll still keep the wait for HPD in the pre_enable() function. Though
it's probably not actually needed there, this driver is used in the
old mode (pre-DP AUX Endpoints) and it may be important for those
cases. If nothing else, it shouldn't cause any big problems.
NOTE: When handling the timeout for HPD we start the timer _after_
we've runtime resumed the device. This is definitely important for the
panel on my homestar which comes up 170 ms after we start timing (the
panel specifies 200 ms max). It's a little unclear how much of this
extra time is due to some internal state machine in the parade
firmware vs. debouncing but it seems to work for the two test cases I
have to do it this way.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220614145327.v4.4.Ie827321ce263be52fdb8c1276f6f8cc00d78029f@changeid
Panel orientation property should be set before drm_dev_register().
Some drm driver calls drm_dev_register() in .bind(). However, most
panels sets orientation property relatively late, mostly in .get_modes()
callback, since this is when they are able to get the connector and
binds the orientation property to it, though the value should be known
when the panel is probed.
In drm_bridge_connector_init(), if a bridge is a panel bridge, use it to
set the connector's panel orientation property.
Suggested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
[dianders: fixed space vs. tab indentation]
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220609072722.3488207-9-hsinyi@chromium.org
Panels usually call drm_connector_set_panel_orientation(), which is
later than drm/kms driver calling drm_dev_register(). This leads to a
WARN().
The orientation property is known earlier. For example, some panels
parse the property through device tree during probe.
Add an API to return the property from panel to drm/kms driver, so the
drivers are able to call drm_connector_set_orientation_from_panel() before
drm_dev_register().
Suggested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
[dianders: removed space before tab]
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220609072722.3488207-2-hsinyi@chromium.org
