Fix following warning when CONFIG_DEBUG_FS wasn't selected:
arch/arm/mach-omap2/pm-debug.c:57: warning: 'pm_dbg_init' declared 'static' but never defined
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Currently, DSS does not wakeup when there is a DMA request. DSS wake
up event must be enabled so that the DMA request to refill the FIFO
will wake up the CORE domain.
Signed-off-by: Subramani Venkatesh <subramani.venkatesh@windriver.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
During suspend, the kernel timekeeping subsystem is shut down. Before
suspend and upon resume, it uses a weak function
read_persistent_clock() to determine the amount of time that elapsed
during suspend.
This function was not implemented on OMAP, so from the timekeeping
subsystem perspective (and thus userspace as well) it appeared that no
time elapsed during suspend.
This patch uses the 32k sync timer as a the persistent clock.
NOTE: This does *NOT* fully handle wrapping of the 32k sync timer, so
more than one wrapping of the 32k sync timer during suspend may
cause problems. Also note there are not interrupts when the 32k
sync timer wraps, so something else has to be done.
Reported-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Due to OMAP3 erratas 1.157, 1.185 the save of the last pad register
(ETK_D14 and ETK_D15) can fail sometimes when there is simultaneous
OCP access to the SCM register area. Fixed by writing the last
register to the save area.
Also, optimized the delay loop for the HW save to include an udelay(1),
which limits the number of unnecessary HW accesses to SCM register area
during the save.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Acked-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
val is an u64 pointer, we need an int to check the error.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Wake-up from McBSP ports are needed, especially when the THRESHOLD
dma mode is in use for audio playback.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The PM debug code fails to build on when CONFIG_DEBUG_FS is not
enabled.
Build error log:
arch/arm/mach-omap2/built-in.o: In function `omap_sram_idle':
arch/arm/mach-omap2/pm34xx.c:449: undefined reference to `pm_dbg_regset_save'
arch/arm/mach-omap2/pm34xx.c:460: undefined reference to `pm_dbg_regset_save'
arch/arm/mach-omap2/built-in.o: In function `configure_vc':
arch/arm/mach-omap2/pm34xx.c:1237: undefined reference to `pm_dbg_regset_init'
arch/arm/mach-omap2/pm34xx.c:1238: undefined reference to `pm_dbg_regset_init'
make: *** [.tmp_vmlinux1] Error 1
This patch fixes the above errors.
Kernel booting is tested on omap zoom2 and zoom3 boards.
Signed-off-by: Manjunatha GK <manjugk@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
As part of Core domain context restoration while coming out of off mode
there are some registers being restored which are not required to be restored.
ROM code will have restored them already. Overwriting some of them can have
potential side effect. Eg: CM_CLKEN_PLL register should not be written while dpll is locked.
Tested on OMAP 3430 SDP for suspend/resume and off mode with sleep_while_idle enabled.
Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Current value is stored on SDRAM and it is written back during wakeup.
Previously a static value of 0x72 was written there.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Acked-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Previously used u32 as temporary data storage that wraps around at 4.294s.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch removes code blocks that are repeated
in function prcm_setup_regs().
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
OMAP interrupt controller goes to unknown state when there is right
combination of l3,l4 sleep/wake-up transitions, l4 autoidle in
interrupt controller and some interrupt. When this happens, interrupts
are not delivered to ARM anymore and ARM will remain in WFI (wait for
interrupt) until interrupt controller is forced to wake-up
(i.e. lauterbach).
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Enable the auto-idle feature of the SCM block to save some additional
power.
Signed-off-by: Mika Westerberg <ext-mika.1.westerberg@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Suspending drivers may still generate interrupts just before their suspend is
completed. Any pending interrupts here will prevent sleep.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Don't assume that gpmc_l3_clk is on, enable it before touching
configuration registers.
Note that the current code assumes that this clock is always
enabled. We are already setting smart idle and L3 autogating
for GPMC clock in gpmc_init.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the rest of the conflict detection and resolution logic necessary
to support more than one counter at a time on sparc64.
The structure and implementation closely mimicks that of powerpc.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pretty straightforward, and it should be easy to add accurate
walk through of signal stack frames in userspace.
Signed-off-by: David S. Miller <davem@davemloft.net>
Tested-by: Jens Axboe <jens.axboe@oracle.com>
Originally patched by Neil Horman <nhorman@tuxdriver.com>
e1000e could with a jumbo frame enabled interface, and packet split disabled,
receive a packet that would overflow a single rx buffer. While in practice
very hard to craft a packet that could abuse this, it is possible.
this is related to CVE-2009-4538
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Originally From: Neil Horman <nhorman@tuxdriver.com>
Modified by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Hey all-
A security discussion was recently given:
http://events.ccc.de/congress/2009/Fahrplan//events/3596.en.html
And a patch that I submitted awhile back was brought up. Apparently some of
their testing revealed that they were able to force a buffer fragment in e1000
in which the trailing fragment was greater than 4 bytes. As a result the
fragment check I introduced failed to detect the fragement and a partial
invalid frame was passed up into the network stack. I've written this patch
to correct it. I'm in the process of testing it now, but it makes good
logical sense to me. Effectively it maintains a per-adapter state variable
which detects a non-EOP frame, and discards it and subsequent non-EOP frames
leading up to _and_ _including_ the next positive-EOP frame (as it is by
definition the last fragment). This should prevent any and all partial frames
from entering the network stack from e1000.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable count and i are unsigned so the (<|>=)0 tests do not work.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There was some left over #ifdef ARM logic that is outdated but no one
really noticed. So instead of relying on this tricky logic, properly
load and utilize the platform irq_flags resources.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Lothar Wassmann <LW@KARO-electronics.de>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some hosts that treat the return value of sizeof differently from unsigned
long might still hit warnings. So use %zu for sizeof() values. This is a
better version of the previous commit b0a9cf297e.
Signed-off-by: Lothar Wassmann <LW@KARO-electronics.de>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Resolves kernel.org bug 14914.
Remove entry for 2770:915d (usb digital camera with mass storage
support) from unusual_devs.h. The fix triggered by the entry causes
the file system on the camera to be completely inaccessible (no
partition table, the device is not mountable).
The patch works, but let me clarify a few things about it. All the
patch does is remove the entry for this device from the
drivers/usb/storage/unusual_devs.h, which is supposed to help with a
problem with the device's reported size (I think). I'm pretty sure it
was originally added for a reason, so I'm not sure removing it won't
cause other problems to reappear. Also, I should note that this
unusual_devs.h entry was present (and activating workarounds) in
2.6.29, but in that version everything works fine. Starting with
2.6.30, things no longer work.
Signed-off-by: Ryan May <rmay31@gmail.com>
Cc: Rohan Hart <rohan.hart17@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This error message is not actually an error, it's an information
message. It is triggered when a transfer which ended in a NAQ is
retried successfully by the hardware.
Signed-off-by: Colin Tuckley <colin.tuckley@arm.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Borislav Petkov reports issues with duplicate sysfs endpoint files after a
resume from a hibernate. It turns out that the code to support alternate
settings under xHCI has issues when a device with a non-default alternate
setting is reset during the hibernate:
[ 427.681810] Restarting tasks ...
[ 427.681995] hub 1-0:1.0: state 7 ports 6 chg 0004 evt 0000
[ 427.682019] usb usb3: usb resume
[ 427.682030] ohci_hcd 0000:00:12.0: wakeup root hub
[ 427.682191] hub 1-0:1.0: port 2, status 0501, change 0000, 480 Mb/s
[ 427.682205] usb 1-2: usb wakeup-resume
[ 427.682226] usb 1-2: finish reset-resume
[ 427.682886] done.
[ 427.734658] ehci_hcd 0000:00:12.2: port 2 high speed
[ 427.734663] ehci_hcd 0000:00:12.2: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT
[ 427.746682] hub 3-0:1.0: hub_reset_resume
[ 427.746693] hub 3-0:1.0: trying to enable port power on non-switchable hub
[ 427.786715] usb 1-2: reset high speed USB device using ehci_hcd and address 2
[ 427.839653] ehci_hcd 0000:00:12.2: port 2 high speed
[ 427.839666] ehci_hcd 0000:00:12.2: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT
[ 427.847717] ohci_hcd 0000:00:12.0: GetStatus roothub.portstatus [1] = 0x00010100 CSC PPS
[ 427.915497] hub 1-2:1.0: remove_intf_ep_devs: if: ffff88022f9e8800 ->ep_devs_created: 1
[ 427.915774] hub 1-2:1.0: remove_intf_ep_devs: bNumEndpoints: 1
[ 427.915934] hub 1-2:1.0: if: ffff88022f9e8800: endpoint devs removed.
[ 427.916158] hub 1-2:1.0: create_intf_ep_devs: if: ffff88022f9e8800 ->ep_devs_created: 0, ->unregistering: 0
[ 427.916434] hub 1-2:1.0: create_intf_ep_devs: bNumEndpoints: 1
[ 427.916609] ep_81: create, parent hub
[ 427.916632] ------------[ cut here ]------------
[ 427.916644] WARNING: at fs/sysfs/dir.c:477 sysfs_add_one+0x82/0x96()
[ 427.916649] Hardware name: System Product Name
[ 427.916653] sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:12.2/usb1/1-2/1-2:1.0/ep_81'
[ 427.916658] Modules linked in: binfmt_misc kvm_amd kvm powernow_k8 cpufreq_ondemand cpufreq_powersave cpufreq_userspace freq_table cpufreq_conservative ipv6 vfat fat
+8250_pnp 8250 pcspkr ohci_hcd serial_core k10temp edac_core
[ 427.916694] Pid: 278, comm: khubd Not tainted 2.6.33-rc2-00187-g08d869a-dirty #13
[ 427.916699] Call Trace:
The problem is caused by a mismatch between the USB core's view of the
device state and the USB device and xHCI host's view of the device state.
After the device reset and re-configuration, the device and the xHCI host
think they are using alternate setting 0 of all interfaces. However, the
USB core keeps track of the old state, which may include non-zero
alternate settings. It uses intf->cur_altsetting to keep the endpoint
sysfs files for the old state across the reset.
The bandwidth allocation functions need to know what the xHCI host thinks
the current alternate settings are, so original patch set
intf->cur_altsetting to the alternate setting 0. This caused duplicate
endpoint files to be created.
The solution is to not set intf->cur_altsetting before calling
usb_set_interface() in usb_reset_and_verify_device(). Instead, we add a
new flag to struct usb_interface to tell usb_hcd_alloc_bandwidth() to use
alternate setting 0 as the currently installed alternate setting.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Borislav Petkov <petkovbb@googlemail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These controllers say "unknown" for their speed in sysfs, which
obviously isn't correct.
Reported-by: Kurt Garloff <garloff@novell.com>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: David Vrabel <david.vrabel@csr.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1330) fixes a bug in khbud's handling of remote
wakeups. When a device sends a remote-wakeup request, the parent hub
(or the host controller driver, for directly attached devices) begins
the resume sequence and notifies khubd when the sequence finishes. At
this point the port's SUSPEND feature is automatically turned off.
However the device needs an additional 10-ms resume-recovery time
(TRSMRCY in the USB spec). Khubd does not wait for this delay if the
SUSPEND feature is off, and as a result some devices fail to behave
properly following a remote wakeup. This patch adds the missing
delay to the remote-wakeup path.
It also extends the resume-signalling delay used by ehci-hcd and
uhci-hcd from 20 ms (the value in the spec) to 25 ms (the value we use
for non-remote-wakeup resumes). The extra time appears to help some
devices.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Cc: Rickard Bellini <rickard.bellini@ericsson.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1321) fixes a problem with EHCI and UHCI root-hub
suspends: If the suspend occurs while a port is trying to resume, the
resume doesn't finish and simply gets lost. When remote wakeup is
enabled, this is undesirable behavior.
The patch checks first to see if any port resumes are in progress, and
if they are then it fails the root-hub suspend with -EBUSY.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1320) fixes two problems related to interrupt-URB
scheduling in ehci-hcd.
URBs with an interval of 2 or 4 microframes aren't handled.
For the time being, the patch reduces to interval to 1 uframe.
URBs are constrained to have an interval no larger than 1024
frames by usb_submit_urb(). But some EHCI controllers allow
use of a schedule as short as 256 frames; for these
controllers we may have to decrease the interval to the
actual schedule length.
The second problem isn't very significant since few devices expose
interrupt endpoints with an interval larger than 256 frames. But the
first problem is critical; it will prevent the kernel from working
with devices having interrupt intervals of 2 or 4 uframes.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Tested-by: Glynn Farrow <farrowg@sg.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Memory allocations with GFP_KERNEL can cause IO to a storage
device which can fail resulting in a need to reset the device.
Therefore GFP_KERNEL cannot be safely used between usb_lock_device()
and usb_unlock_device(). Replace by GFP_NOIO.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a mask bit which was mistakenly omitted from the
as1311 patch (usb-storage: add BAD_SENSE flag).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix a regression introduced by commit
715b1dc01f ("USB: usb_debug,
usb_generic_serial: implement multi urb write").
URB transfer buffer was never freed when using multi-urb writes.
Currently the only driver enabling multi-urb writes is usb_debug.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: Greg KH <greg@kroah.com>
Acked-by: Jason Wessel <jason.wessel@windriver.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fix a possible race bug in drivers/usb/serial/generic with
the new kfifo API.
Please apply it to the 2.6.33-rc* tree.
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes a number of SMP problems that were in the hyperv core code.
Patch originally written by K. Y. Srinivasan <ksrinivasan@novell.com>
but forward ported to the latest in-kernel code and tweaked slightly by
me.
Novell, Inc. hereby disclaims all copyright in any derivative work
copyright associated with this patch.
Signed-off-by: K. Y. Srinivasan <ksrinivasan@novell.com>
Cc: Hank Janssen <hjanssen@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>.
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
et131x: Fix 12bit wrapping
From: Alan Cox <alan@linux.intel.com>
The 12bit wrap logic conversion is wrong and this shows up for some
memory sizes and layouts of card. Patch it up for now, once the kernel
view of status is cleaned up it'll become two variables and a lot saner.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After updating to 2.6.32 kernel, I started experiencing Oopses caused by
the asus_oled module. After quick investigation, I wrapped this simple
patch which fixes an Oops in by asus_oled module on 2.6.32.2 kernel,
caused by incorrect usage of strict_strtoul function call within
set_enabled and set_disabled functions. This can be triggered by simple
running the userspace client for asus_old (e.g., 'asusoled -e' or
'asusoled -d').
Signed-off-by: Eugeni Dodonov <eugeni@mandriva.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We need to keep the lock held over the call to __f_setown() to
prevent a PID race.
Thanks to Al Viro for pointing out the problem, and to Travis for
making us look here in the first place.
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Tavis Ormandy <taviso@google.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Julien Tinnes <jln@google.com>
Cc: Matt Mackall <mpm@selenic.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Quirk is applied on all cards with given manfid (is it that correct?).
Unfortunately, that quirk breaks resume on zaurus with billionton
bluetooth card inserted: c950ctrl is 0 and outb() faults.
I believe it is simply not a multiport card. (info->multi == 1). ...
... confirmed by printks.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since UCR1_UARTEN is defined 1, the port was always treated as enabled.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Acked-by: Oskar Schirmer <os@emlix.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Fabian Godehardt <fg@emlix.com>
Cc: Daniel Glöckner <dg@emlix.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In that situation if the old rate is invalid and the new rate is invalid
and the chip cannot do 9600 baud we report zero, which makes all the
drivers explode.
Instead force the rate based on min/max
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Perform a tricky suspend/resume even with no_console_suspend.
With no_console_suspend, kernel skips serial port suspend/resume and the
serial hardware may remain in undefined state after resume. It actually
happens on devices that don't have BIOS that handle serial
initialization. It makes impossible to use serial console after resume.
Devices affected by this problem include:
Sharp Zaurus devices
Several PXA based ARM embedded boards
The patch does:
- Save the hardware state
- Perform buffer flush in time of its suspend call
- Tell the driver that port is suspended
- But still accept new data
- And keep console hardware in state that allows to send them
It allows to capture late console messages without breaking console
after resume.
This is just a resend of a patch discussed in these threads, as the
patch was not yet applied.
"Possible suspend/resume regression in .32-rc?" (Nov 1-5, 2009, ARM
list, later LKML)
"serial-core: resume serial hardware with no_console_suspend" (Sep
15-Oct 18, 2009, LKML & ARM lists)
Signed-off-by: Stanislav Brabec <sbrabec@suse.cz>
Tested-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Tested-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Wacom claims that the WACF namespace will always be devoted to serial
Wacom tablets. Remove the existing entries and add a wildcard to avoid
having to update the kernel every time they add a new device.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Tested-by: Ping Cheng <pingc@wacom.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Nozomi goes wrong if you get the sequence
open
open
close
[stuff]
close
which turns out to occur on some ppp type setups.
This is a quick patch up for the problem. It's not really fixing Nozomi
which completely fails to implement tty open/close semantics and all the
other needed stuff. Doing it right is a rather more invasive patch set and
not one that will backport.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After the commit fb07a5f8 ("compat_ioctl: remove all VT ioctl
handling"), I got this error message on 64-bit mips kernel with 32-bit
busybox userland:
ioctl32(init:1): Unknown cmd fd(0) cmd(00005600){t:'V';sz:0} arg(7fd76480) on /dev/console
The cmd 5600 is VT_OPENQRY. The busybox's init issues this ioctl to
know vt-console or serial-console. If the console was serial console,
VT ioctls are not handled by the serial driver.
And by quick search, I found some programs using VT_GETMODE to check
vt-console is available or not.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
