* Continue replacing "CONSTANT & var" tests with "var & CONSTANT"
* Don't clear EDMA_CFG_NCQ_GO_ON_ERR on Gen-IIE, where that bit does
not exist
* Set I/O Id field in descriptor, where present. Appears to work
fine on all versions, even though queueing is still disabled.
* call pci_set_mwi(), to (a) make sure cacheline size is set properly,
and (b) enable MWI transactions
* Remove never-used handling of coalescing interrupt bits (these events
are always masked)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Minor cleanups, new definitions, and code movement, preparing for
upcoming new-EH and NCQ changes. This commit shoult not change behavior
at all.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Separate out ata_eh_handle_dev_fail() from ata_eh_recover(). This is
in preparation of ata_link and PMP support.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add Hitachi HDS7250SASUN500G 0621KTAWSD to list of devices with broken NCQ.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Workaround for errata A308: turn down the UDMA mode and retry
the DMA command when the data lost condition is detected.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Akira Iguchi <akira2.iguchi@toshiba.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Please warmly welcome the first member from FUJITSU to the prestigious
NCQ spurious completion club.
This is reported by Serge Van Thillo in bugzilla bug 8730.
http://bugzilla.kernel.org/show_bug.cgi?id=8730
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Serge van Thillo <nulleke@hotmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The HPT343/345 (aka 363) is a bit of a warped device. For many setups you
need to access the other registers via BAR4 offsets. PIO is now rock
solid, DMA isn't. Unfortunately the drivers/ide hpt34x driver is
completely broken so doesn't help further debug.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Horkage handling had the following problems.
* dev->horkage was positioned after ATA_DEVICE_CLEAR_OFFSET, so it was
cleared before the device is configured. This broke
HORKAGE_DIAGNOSTIC.
* Some used dev->horkage while others called ata_device_blacklisted()
directly. This was at best confusing.
This patch moves dev->horkage right after dev->flags and set the field
according to the blacklist during device configuration. All users
test against dev->horkage. ata_device_blacklisted() now has only one
user, make it static. While at it, rename it to ata_dev_blacklisted()
for consistency.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The Zip 250 which chokes on MWDMA SET_XFERMODE sometimes have "Floppy"
appeneded to its model number. Quirk it too.
http://bugzilla.kernel.org/show_bug.cgi?id=8563
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Hans de Bruin <bruinjm@xs4all.nl>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
With PCI resource fix up for legacy hosts. We can use the same code
path to allocate IO resources and initialize host for both legacy and
native SFF hosts. Only IRQ requesting needs to be different.
Rename ata_pci_*_native_host() to ata_pci_*_sff_host(), kill all
legacy specific functions and use the renamed functions instead. This
simplifies code a lot.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement suspend and resume routines for mpc52xx ata driver.
Tested on Lite5200b with deep-sleep and low-power (not yet in-tree)
modes.
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch enables hotplugging of SATA devices in the
sata_promise driver. It's been tested successfully on
both first- and second-generation Promise SATA chips:
SATA150 TX2plus, SATAII150 TX2plus, SATAII150 TX4,
SATA300 TX2plus, and SATA300 TX4.
The only quirk I've seen is that hotplugging (insertion)
on the first-generation SATA150 TX2plus requires a lengthier
EH sequence than on the second-generation chips.
On the second-generation chips a simple soft reset seems
to suffice, but on the first-generation chip there's a
"port is slow to respond" after the initial soft reset,
after which libata issues a hard reset, and then the
device is recognised.
The hotplug checks are high up in the interrupt handling
path, not deep down in error_intr as in ahci/sata_sil24.
That's because the chip doesn't signal hotplug status changes
in the per-port status register: instead a global register
contains hotplug control and status flags for all ports.
I considered following the ahci/sata_sil24 structure, but
that would have required non-trivial changes to the interrupt
handling path, so I chose to keep the hotplug changes simple
and unobtrusive.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
--
This patch depends on the "sata_promise: cleanups" patch.
Changes since the previous version (posted June 19):
- Correct pdc_interrupt() to increment 'handled' also in
the hotplug case. This prevents IRQ_NONE from being
returned when an interrupt only has hotplug events to
handle, which could confuse the kernel's IRQ machinery.
- Added testing on the SATAII150 TX4.
drivers/ata/sata_promise.c | 41 ++++++++++++++++++++++++++++++++++++-----
1 files changed, 36 insertions(+), 5 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If you are using a SiS controller and the BIOS didn't set it up then the
FIFO may be left active when we try and set up the CD. Not convinced this
matters but I'd prefer to be safe
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We should not use cancel_work_sync(delayed_work->work). This works, but not
good. We can use cancel_rearming_delayed_work(), this also simplifies the
code.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Indicate whether this is a Generation-I (50xx), Generation-II (60xx),
or Generation-II-E (6042/7042) chip.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The ATA_UDMAx masks are self-documenting, and far better than manually
writing in the hex mask.
Note that pata_it8213 mask differed from the comment. Added a FIXME there.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add support for the SATA portion of Marvell's AHCI-compatible chips.
The PATA port capability, also available via AHCI, is disabled until
support is completed.
NCQ and PCI MSI are disabled by default. Marvell says "we use NCQ" in
their drivers but "we do not use PCI MSI." Theoretically that implies
we need to fix ahci.c to work with Marvell NCQ, but one wonders why
Marvell NCQ is any different from other AHCI chips.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* Use ATA_UDMA*
* Remove FIXME notations that once served to remind us to verify
that these were indeed the correct UDMA masks. They are.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add ata_dumb_qc_prep and supporting logic so that a driver can just
specify it needs to be helped in this area. 64K entries are split
as with drivers/ide.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
sil24_interrupt() loads host->ports[i] into a local variable,
validates it, and then loads the value again in the call to
sil24_host_intr(). This patch replaces the second load by a
reference to the local variable.
This is safe since no side-effects have occurred since the
initial load. It also improves readability since it makes
it clear that the parameter to sil24_host_intr() is the same
value which was just validated.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On some embedded platforms, such as blackfin, the gpio interrupt for
IDE interface is designed to be triggered with high voltage. The gpio
port should be configured properly by set_irq_type() when register
the irq. This patch enable the generic pata platform driver to
accept platform irq flags data.
Signed-off-by: Sonic Zhang <sonic.adi@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch applies some trivial cleanups to sata_promise:
- repair whitespace damage
- correct comment at board_2057x_pata definition
- pull SATAII TX4 support code out to separate functions
- rename ata_nr to ata_no for consistency with libata's port_no
- remove some init-time debug printks (requested by Jeff)
This patch should cause no behavioural changes, except for
the removed printks.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
--
drivers/ata/sata_promise.c | 56 ++++++++++++++++++---------------------------
1 files changed, 23 insertions(+), 33 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix various bugs in pio/mwdma mode programming.
* Control bits in the timing register wasn't cleared properly while
programming PIO mode.
* MWDMA mode programming cleared the wrong part of control bits.
* MWDMA mode programming cleared udma_mask even when the controller
doesn't support UDMA.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Art Haas <ahaas@airmail.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
sata_sx4:
- describe overall driver theory of operation
- add a few constants that will be used in the future
sata_via:
- remove mention of an old-EH function that is going away
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* convert tabs to spaces
* convert some hex numbers to (1 << n) preferred format
* document i2c and timer control register bits
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make it easier to verify which struct initializers are present, by
presenting them in the order in which they are defined in the API
header.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This flag only has meaning in old-EH drivers, and these drivers have
already been converted to the new EH. Remove.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make the register offset table more maintainable.
From the 'sii-lbt' branch, which enables the LBT chip feature.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ahci: enable sg segment clustering
The specification states that ahci supports segments up to 4MiB in size,
so enable clustering.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ap->cbl == ATA_CBL_SATA indicates SATA cable while ap->flags &
ATA_FLAG_SATA indicates SATA host port. Till now they always gave the
same result but SATA/PATA bridge handling will change that. Switch to
ATA_FLAG_SATA test if we're testing for host port type.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement _GTM/_STM support. acpi_gtm is added to ata_port which
stores _GTM parameters over suspend/resume cycle. A new hook
ata_acpi_on_suspend() is responsible for storing _GTM parameters
during suspend. _STM is executed in ata_acpi_on_resume(). With this
change, invoking _GTF is safe on IDE hierarchy and acpi_sata check
before _GTF is removed.
ata_acpi_gtm() and ata_acpi_stm() implementation is taken from Alan
Cox's pata_acpi implementation. ata_acpi_gtm() is fixed such that the
result parameter is not shifted by sizeof(union acpi_object).
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch reimplements ACPI invocation such that, instead of
exporting ACPI details to the rest of libata, ACPI event handlers -
ata_acpi_on_resume() and ata_acpi_on_devcfg() - are used. These two
functions are responsible for determining whether specific ACPI method
is used and when.
On resume, _GTF is scheduled by setting ATA_DFLAG_ACPI_PENDING device
flag. This is done this way to avoid performing the action on wrong
device device (device swapping while suspended).
On every ata_dev_configure(), ata_acpi_on_devcfg() is called, which
performs _SDD and _GTF. _GTF is performed only after resuming and, if
SATA, hardreset as the ACPI spec specifies. As _GTF may contain
arbitrary commands, IDENTIFY page is re-read after _GTF taskfiles are
executed.
If one of ACPI methods fails, ata_acpi_on_devcfg() retries on the
first failure. If it fails again on the second try, ACPI is disabled
on the device. Note that successful configuration clears ACPI failed
status.
With all feature checks moved to the above two functions,
do_drive_set_taskfiles() is trivial and thus collapsed into
ata_acpi_exec_tfs(), which is now static and converted to return the
number of executed taskfiles to be used by ata_acpi_on_resume(). As
failures are handled properly, ata_acpi_push_id() now returns -errno
on errors instead of unconditional zero.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* Add missing LOCKING: and RETURNS: to function comment.
* Don't conditionalize warning messages with ata_msg_probe(). Print
directly with KERN_WARNING.
* Drop duplicate debug messages.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch cleans up ata_acpi_exec_tfs() and its friends.
* Rename taskfile_array to ata_acpi_gtf and make it __packed as it's
used as argument to ACPI method, and use pointer to ata_acpi_gtf and
number of taskfiles to represent _GTF taskfiles instead of a pointer
casted into unsigned long and byte count. This makes argument
re-checking in do_drive_set_taskfiles() unnecessary.
* Pointer in void * not in unsigned long.
* Clean up do_drive_get_GTF() error handling and make
do_drive_get_GTF() return number of taskfiles on success, 0 if _GTF
doesn't exist or doesn't contain valid ata. -errno on other errors.
* Remove superflous check for acpi->buffer.pointer.
* Update taskfile_load_raw() such that printed messages look similar
to the messages printed by ata_eh_report().
* s/do_drive_get_GTF/ata_dev_get_GTF/
s/do_drive_set_taskfiles/ata_dev_set_taskfiles/
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* Add acpi_handle to ata_host and ata_port. Rename
ata_device->obj_handle to ->acpi_handle and move it above such that
it doesn't get cleared on reconfiguration.
* Replace ACPI node association which ata_acpi_associate() which is
called once during host initialization. Unlike the previous
implementation, ata_acpi_associate() uses ATA_FLAG_ACPI_SATA to
choose between IDE or SATA ACPI hierarchy and uses simple child look
up instead of recursive walk to match the nodes. This is way safer
and simpler. Please read the following message for more info.
http://article.gmane.org/gmane.linux.ide/17554
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
PCMCIA doesn't use DMA and as this driver is used on many platforms we
don't want it to fail on those that define the DMA alloc API as a NULL
return
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We got it backwards and now the other detects are fixed it shows up
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
