Use devm_of_iomap() to map resources. This will avoid the necessity to
track the mapped resources and free them on failure path or on remove.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Suggested-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Normal parentheses should be used when referring to config variables
in Makefile. Replace the accidentally introduced curly brackets by
regular parentheses.
Fixes: a7f79f9954 ("power: reset: add driver for LinkStation power off")
Acked-by: Daniel González Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Change 'stanalone' to 'standalone'
Change 'mesaurement' to 'measurement'
Change 'nonvilatile' to 'nonvolatile'
Change 'unical' to 'unique'
Change 'unaccesable' to 'unaccessible'
Change 'correcpondent' to 'correspond'
Signed-off-by: Xiaofeng Cao <caoxiaofeng@yulong.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Use kobj_to_dev() instead of open-coding it
Signed-off-by: dongjian <dongjian@yulong.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add support for TI BQ78Z100, I2C interface gas gauge.
It provides a fully integrated safety protection
and authentication for 1 to 2-series cell Li-Ion and
Li-Polymer battery packs.
The patch was tested with BQ78Z100 equipment.
CASE I: Discharging:
POWER_SUPPLY_NAME=bq78z100-0
POWER_SUPPLY_STATUS=Discharging
POWER_SUPPLY_PRESENT=1
POWER_SUPPLY_VOLTAGE_NOW=3386000
POWER_SUPPLY_CURRENT_NOW=-5000
POWER_SUPPLY_CAPACITY=27
POWER_SUPPLY_CAPACITY_LEVEL=Normal
POWER_SUPPLY_TEMP=269
POWER_SUPPLY_TIME_TO_EMPTY_NOW=1249920
POWER_SUPPLY_TECHNOLOGY=Li-ion
POWER_SUPPLY_CHARGE_FULL=6494000
POWER_SUPPLY_CHARGE_NOW=1736000
POWER_SUPPLY_CHARGE_FULL_DESIGN=6000000
POWER_SUPPLY_CYCLE_COUNT=1
POWER_SUPPLY_POWER_AVG=-20000
POWER_SUPPLY_HEALTH=Good
POWER_SUPPLY_MANUFACTURER=Texas Instruments
CASE II : No discharging current:
POWER_SUPPLY_NAME=bq78z100-0
POWER_SUPPLY_STATUS=Not charging
POWER_SUPPLY_PRESENT=1
POWER_SUPPLY_VOLTAGE_NOW=3386000
POWER_SUPPLY_CURRENT_NOW=0
POWER_SUPPLY_CAPACITY=27
POWER_SUPPLY_CAPACITY_LEVEL=Normal
POWER_SUPPLY_TEMP=270
POWER_SUPPLY_TECHNOLOGY=Li-ion
POWER_SUPPLY_CHARGE_FULL=6494000
POWER_SUPPLY_CHARGE_NOW=1734000
POWER_SUPPLY_CHARGE_FULL_DESIGN=6000000
POWER_SUPPLY_CYCLE_COUNT=1
POWER_SUPPLY_POWER_AVG=0
POWER_SUPPLY_HEALTH=Good
POWER_SUPPLY_MANUFACTURER=Texas Instruments
Signed-off-by: LI Qingwu <Qing-wu.Li@leica-geosystems.com.cn>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
There are multiple issues in bq27xxx_battery_status():
- On BQ28Q610 is was observed that the "full" flag may be set even while
the battery is charging or discharging. With the current logic to make
"full" override everything else, it look a very long time (>20min) for
the status to change from "full" to "discharging" after unplugging the
supply on a device with low power consumption
- The POWER_SUPPLY_STATUS_NOT_CHARGING check depends on
power_supply_am_i_supplied(), which will not work when the supply
doesn't exist as a separate device known to Linux
We can solve both issues by deriving the status from the current instead
of the flags field. The flags are now only used to distinguish "full"
from "not charging", and to determine the sign of the current on
BQ27XXX_O_ZERO devices.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
On all newer bq27xxx ICs, the AveragePower register contains a signed
value; in addition to handling the raw value as unsigned, the driver
code also didn't convert it to µW as expected.
At least for the BQ28Z610, the reference manual incorrectly states that
the value is in units of 1mW and not 10mW. I have no way of knowing
whether the manuals of other supported ICs contain the same error, or if
there are models that actually use 1mW. At least, the new code shouldn't
be *less* correct than the old version for any device.
power_avg is removed from the cache structure, se we don't have to
extend it to store both a signed value and an error code. Always getting
an up-to-date value may be desirable anyways, as it avoids inconsistent
current and power readings when switching between charging and
discharging.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Commit cd060b4d08 ("power: supply: bq27xxx: fix polarity of current_now")
changed the sign of current_now for all bq27xxx variants, but on BQ28Z610
I'm now seeing negated values *with* that patch.
The GTA04/Openmoko device that was used for testing uses a BQ27000 or
BQ27010 IC, so I assume only the BQ27XXX_O_ZERO code path was incorrect.
Revert the behaviour for newer ICs.
Fixes: cd060b4d08 "power: supply: bq27xxx: fix polarity of current_now"
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
There are two regmap_update_bits() calls but only one of them has
return value check, which is odd. Add a return value check and
terminate the execution flow on failure just like the other call.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The kernel test robot reports an unused variable in the
Z2 battery code caused by a recent commit.
Fixes: a3b4388ea1 ("power: supply: z2_battery: Convert to GPIO descriptors")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Improve formatting of the code by removing unnecessary whitespaces.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
A previous commit attempted to fix IRQ usage in a case where interrupt
is failed to initialize, but it missed couple more cases that could be
improved. The interrupt could be undefined and then everything related
to interrupt shouldn't be touched by driver. Secondly, we shouldn't ignore
errors that aren't directly related to enabling interrupt in hardware,
like enabling h/w write-access or requesting interrupt. Improve interrupt
initialization in the driver in order to handle the missing cases.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The "pdata" local variable is not used in suspend/resume handlers since
commit 7776bcd241 ("power: supply: s3c-adc-battery: Convert to GPIO
descriptors"):
drivers/power/supply/s3c_adc_battery.c: In function ‘s3c_adc_bat_suspend’:
drivers/power/supply/s3c_adc_battery.c:405:28: warning: unused variable ‘pdata’ [-Wunused-variable]
drivers/power/supply/s3c_adc_battery.c: In function ‘s3c_adc_bat_resume’:
drivers/power/supply/s3c_adc_battery.c:422:28: warning: unused variable ‘pdata’ [-Wunused-variable]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
CHARGE_NOW is expected by some user software (such as waybar)
instead of 'CAPACITY', in order to correctly calculate remaining battery
life.
Signed-off-by: Martin Ashby <martin@ashbysoft.com>
Reviewed-by: Tobias Schramm <t.schramm@manjaro.org>
Tested-by: Tobias Schramm <t.schramm@manjaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Use kobj_to_dev() instead of open-coding it
Signed-off-by: Jian Dong <dongjian@yulong.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The zte zx platform is getting removed, so this driver is no
longer needed.
Cc: Jun Nie <jun.nie@linaro.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The i2c_device_id bq25975 is repeated, and should be bq25960.
Signed-off-by: xinjian <xinjian@yulong.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The IRQ=0 could be a valid interrupt number in kernel because interrupt
numbers are virtual in a modern kernel. Hence fix the interrupt usage in
a case if interrupt is unavailable by not overriding the interrupt number
which is used by the driver.
Note that currently Nexus 7 is the only know device which uses SMB347
kernel diver and it has a properly working interrupt, hence this patch
doesn't fix any real problems, it's a minor cleanup/improvement.
Fixes: 99298de5df ("power: supply: smb347-charger: Replace mutex with IRQ disable/enable")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The IRQ handler calls mod_delayed_work() on power->vbus_detect. However,
that work item is not initialized until after the IRQs are enabled. If
an IRQ is already pending when the driver is probed, the driver calls
mod_delayed_work() on an uninitialized work item, which causes an oops.
Fixes: bcfb7ae3f5 ("power: supply: axp20x_usb_power: Only poll while offline")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
CHARGER_SBS should select REGMAP_I2C since it uses API(s) that are
provided by that Kconfig symbol.
Fixes these errors:
../drivers/power/supply/sbs-charger.c:149:21: error: variable ‘sbs_regmap’ has initializer but incomplete type
static const struct regmap_config sbs_regmap = {
../drivers/power/supply/sbs-charger.c:150:3: error: ‘const struct regmap_config’ has no member named ‘reg_bits’
.reg_bits = 8,
../drivers/power/supply/sbs-charger.c:155:23: error: ‘REGMAP_ENDIAN_LITTLE’ undeclared here (not in a function)
.val_format_endian = REGMAP_ENDIAN_LITTLE, /* since based on SMBus */
../drivers/power/supply/sbs-charger.c: In function ‘sbs_probe’:
../drivers/power/supply/sbs-charger.c:183:17: error: implicit declaration of function ‘devm_regmap_init_i2c’; did you mean ‘devm_request_irq’? [-Werror=implicit-function-declaration]
chip->regmap = devm_regmap_init_i2c(client, &sbs_regmap);
../drivers/power/supply/sbs-charger.c: At top level:
../drivers/power/supply/sbs-charger.c:149:35: error: storage size of ‘sbs_regmap’ isn’t known
static const struct regmap_config sbs_regmap = {
Fixes: feb583e37f ("power: supply: add sbs-charger driver")
Reported-by: Martin Mokrejs <mmokrejs@fold.natur.cuni.cz>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Martin Mokrejs <mmokrejs@fold.natur.cuni.cz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
current_now has to be negative during discharging and positive during
charging, the behavior seen is the other way round.
Tested on GTA04 with Openmoko battery.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
cm->emergency_stop will only be the value in the enumeration,
and cannot be less than zero, it will get an exception value.
So replace it with the corresponding value.
Signed-off-by: Junlin Yang <yangjunlin@yulong.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add support for SAMA7G5 by adding proper struct reg_config structure
and since SAMA7G5 is not currently on LPDDR setups the commit also
avoid the mapping of DDR controller.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Replace a comma between expression statements by a semicolon.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Replace a comma between expression statements by a semicolon.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
fixed the following coccicheck:
drivers/power/supply/ds2780_battery.c:627:60-61: WARNING opportunity for
kobj_to_dev()
drivers/power/supply/ds2780_battery.c:672:60-61: WARNING opportunity for
kobj_to_dev()
drivers/power/supply/ds2780_battery.c:640:60-61: WARNING opportunity for
kobj_to_dev()
drivers/power/supply/ds2780_battery.c:685:60-61: WARNING opportunity for
kobj_to_dev()
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Currently REG_NAC (nominal available capacity) is mapped to
power-supply's CHARGE_NOW property. Some chips do not have
REG_NAC and do not expose CHARGE_NOW at the moment. Some
bq27xxx chips also have another register REG_RM (remaining
capacity). The difference between REG_NAC and REG_RM is load
compensation.
This patch adds register information for REG_RM for all
supported fuel gauges. On systems having REG_NAC it is
ignored, so behaviour does not change. On systems without
REG_NAC, REG_RM will be used to provide CHARGE_NOW
functionality.
As a result there are three more chips exposing CHARGE_NOW:
bq27z561, bq28z610 and bq34z100
Signed-off-by: Hermes Zhang <chenhuiz@axis.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Currently if the pointer battery is null there is a null pointer
dereference on the call to power_supply_put. Fix this by only
performing the put if battery is not null.
Addresses-Coverity: ("Dereference after null check")
Fixes: 4bff91bb32 ("power: supply: cpcap-charger: Fix missing power_supply_put()")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
There is no dynamic information in cpcap-battery's
power-supply description struct, so let's make it
static const.
Cc: Arthur Demchenkov <spinal.by@gmail.com>
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Fix typo
Cc: Arthur Demchenkov <spinal.by@gmail.com>
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
[tony@atomide.com: separated out from charger changes]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add charge_now property for capacity reporting.
Cc: Arthur Demchenkov <spinal.by@gmail.com>
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Arthur Demchenkov <spinal.by@gmail.com>
[tony@atomide.com: updated to apply for naming changes]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Calculate percentage using charge_full value provided.
Cc: Arthur Demchenkov <spinal.by@gmail.com>
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Arthur Demchenkov <spinal.by@gmail.com>
[tony@atomide.com: updated to apply after dropping my earlier patch]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Save the battery empty and full states so we can use those to estimate
the battery capacity in the following patches.
If the user provides us with charge_full value (which it could save in a
permanent storage between reboots), initialize low and high counter_uah
with calculated values.
If we hit battery low once, we should stick on reporting it until the
charger is connected. This way low->counter_uah will be updated
properly, and that will allow us to get more accurate charge_full value.
Based on an earlier patch by Tony Lindgren with charge_full usage and
other improvments done by Arthur Demchenkov.
Cc: Arthur Demchenkov <spinal.by@gmail.com>
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Co-developed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Arthur Demchenkov <spinal.by@gmail.com>
[tony@atomide.com: combined earlier patches, updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add charge_full property and let user update it. This is needed for
capacity reporting in the following patches.
Cc: Arthur Demchenkov <spinal.by@gmail.com>
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Arthur Demchenkov <spinal.by@gmail.com>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
We now get battery full notification from cpcap-charger, so let's use that
for battery full status and charger disconnect.
Note that any current based battery full detection we have tried earlier is
flakey as it won't account for example for CPU load increasing the battery
current. Anyways, if current based battery full detection is also still
needed, we can reconsider adding it in addition to the charger status based
detection.
Cc: Arthur Demchenkov <spinal.by@gmail.com>
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
We want to have the battery update it's status when the charge is done,
and when the charger is disconnected. Otherwise the battery does not know
when it's full unless there's a userspace app polling the battery status.
To do this, we add supplied_to handling to cpcap-battery, and implement
power_supply_changed() for cpcap-charger. When cpcap-charger calls
power_supply_changed(), cpcap-battery will update it's status.
Let's also use new_state variable for the POWER_SUPPLY_STATUS_CHARGING
case to have unified handling for the switch.
Cc: Arthur Demchenkov <spinal.by@gmail.com>
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Let's turn cpcap_charger_set_state() into separate cpcap_charger_enable()
and cpcap_charger_disable() to simplify things, and to allow managing
status separately. This can be then used for the follow-up patches to
make battery full status behave a bit nicer.
Cc: Arthur Demchenkov <spinal.by@gmail.com>
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
We currently have both state and status, get rid of state and use
generic status instead.
Cc: Arthur Demchenkov <spinal.by@gmail.com>
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Droid 4 has same problem as N900: it is often necessary to manually
tweak current draw from USB, for example when using thin charging cable.
Cc: Arthur Demchenkov <spinal.by@gmail.com>
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
[tony@atomide.com: rebased, cleaned up whitespace issues, updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Just get rid of the custom enumeration if favor of the standard one.
Cc: Arthur Demchenkov <spinal.by@gmail.com>
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This should be only shown when debug is enabled.
Cc: Arthur Demchenkov <spinal.by@gmail.com>
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
If we have a USB charger connected, reboot is flakey and often fails to
reboot the device with the charger LED staying on.
Let's fix this by implementing .shutdown.
Cc: Arthur Demchenkov <spinal.by@gmail.com>
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
