This makes cr_alignment a constant 0 to break code that tries to modify
the value as it's likely that it's built on wrong assumption when
CONFIG_CPU_CP15 isn't defined. For code that is only reading the value 0
is more or less a fine value to report.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Message-Id: 1358413196-5609-2-git-send-email-u.kleine-koenig@pengutronix.de (v8)
Pull ARM fixes from Russell King:
"A number of fixes:
Patrik found a problem with preempt counting in the VFP assembly
functions which can cause the preempt count to be upset.
Nicolas fixed a problem with the parsing of the DT when it straddles a
1MB boundary.
Subhash Jadavani reported a problem with sparsemem and our highmem
support for cache maintanence for DMA areas, and TI found a bug in
their strongly ordered memory mapping type.
Also, three fixes by way of Will Deacon's tree from Dave Martin for
instruction compatibility and Marc Zyngier to fix hypervisor boot mode
issues."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7629/1: mm: Fix missing XN flag for for MT_MEMORY_SO
ARM: DMA: Fix struct page iterator in dma_cache_maint() to work with sparsemem
ARM: 7628/1: head.S: map one extra section for the ATAG/DTB area
ARM: 7627/1: Predicate preempt logic on PREEMP_COUNT not PREEMPT alone
ARM: virt: simplify __hyp_stub_install epilog
ARM: virt: boot secondary CPUs through the right entry point
ARM: virt: Avoid bx instruction for compatibility with <=ARMv4
Pull ARM SoC fixes from Olof Johansson:
"Here's a long-pending fixes pull request for arm-soc (I didn't send
one in the -rc4 cycle).
The larger deltas are from:
- A fixup of error paths in the mvsdio driver
- Header file move for a driver that hadn't been properly converted
to multiplatform on i.MX, which was causing build failures when
included
- Device tree updates for at91 dealing mostly with their new pinctrl
setup merged in 3.8 and mistakes in those initial configs
The rest are the normal mix of small fixes all over the place; sunxi,
omap, imx, mvebu, etc, etc."
* tag 'fixes-for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (40 commits)
mfd: vexpress-sysreg: Don't skip initialization on probe
ARM: vexpress: Enable A7 cores in V2P-CA15_A7's Device Tree
ARM: vexpress: extend the MPIDR range used for pen release check
ARM: at91/dts: correct comment in at91sam9x5.dtsi for mii
ARM: at91/at91_dt_defconfig: add at91sam9n12 SoC to DT defconfig
ARM: at91/at91_dt_defconfig: remove memory specification to cmdline
ARM: at91/dts: add macb mii pinctrl config for kizbox
ARM: at91: rm9200: remake the BGA as default version
ARM: at91: fix gpios on i2c-gpio for RM9200 DT
ARM: at91/at91sam9x5 DTS: add SCK USART pins
ARM: at91/at91sam9x5 DTS: correct wrong PIO BANK values on u(s)arts
ARM: at91/at91-pinctrl documentation: fix typo and add some details
ARM: kirkwood: fix missing #interrupt-cells property
mmc: mvsdio: use devm_ API to simplify/correct error paths.
clk: mvebu/clk-cpu.c: fix memory leakage
ARM: OMAP2+: omap4-panda: add UART2 muxing for WiLink shared transport
ARM: OMAP2+: DT node Timer iteration fix
ARM: OMAP2+: Fix section warning for omap_init_ocp2scp()
ARM: OMAP2+: fix build break for omapdrm
ARM: OMAP2: Fix missing omap2xxx_clkt_vps_late_init function calls
...
From Pawel Moll:
- makes the V2P-CA15_A7 (a.k.a. TC2) work with 3.8 kernels
- improves vexpress-sysreg.c behaviour on arm64 platforms
* 'vexpress/fixes' of git://git.linaro.org/people/pawelmoll/linux:
mfd: vexpress-sysreg: Don't skip initialization on probe
ARM: vexpress: Enable A7 cores in V2P-CA15_A7's Device Tree
ARM: vexpress: extend the MPIDR range used for pen release check
From Nicolas Ferre:
Here are fixes for AT91 that are mainly related to device tree.
One RM9200 setup option is the only C code change.
Some documentation changes can clarify the pinctrl use.
Then, some defconfig modifications are allowing the affected platforms
to boot.
* tag 'at91-fixes' of git://github.com/at91linux/linux-at91:
ARM: at91/dts: correct comment in at91sam9x5.dtsi for mii
ARM: at91/at91_dt_defconfig: add at91sam9n12 SoC to DT defconfig
ARM: at91/at91_dt_defconfig: remove memory specification to cmdline
ARM: at91/dts: add macb mii pinctrl config for kizbox
ARM: at91: rm9200: remake the BGA as default version
ARM: at91: fix gpios on i2c-gpio for RM9200 DT
ARM: at91/at91sam9x5 DTS: add SCK USART pins
ARM: at91/at91sam9x5 DTS: correct wrong PIO BANK values on u(s)arts
ARM: at91/at91-pinctrl documentation: fix typo and add some details
As the kernel is able to cope with multiple clusters,
uncomment the A7 cores in the Device Tree for V2P-CA15_A7
tile, making all 5 cores available to the user.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
In ARM multi-cluster systems the MPIDR affinity level 0 cannot be used as a
single cpu identifier, affinity levels 1 and 2 must be taken into account as
well.
This patch extends the MPIDR usage to affinity levels 1 and 2 in versatile
secondary cores start up code in order to compare the passed pen_release
value with the full-blown affinity mask.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
From Jason Cooper:
mvebu fixes for v3.8-rc5
- fix memory leak in mvebu/clk-cpu.c
- use devm_ to correct/simplify error paths in mvsdio
- add missing #interrupt-cells property in kirkwood
* tag 'mvebu_fixes_for_v3.8-rc5' of git://git.infradead.org/users/jcooper/linux:
ARM: kirkwood: fix missing #interrupt-cells property
mmc: mvsdio: use devm_ API to simplify/correct error paths.
clk: mvebu/clk-cpu.c: fix memory leakage
Concerning pinctrl_macb0_rmii_mii, values were okay, but not comments.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
No need for this cmdline option as we are using DT.
Moreover this defconfig is targeted to multiple SoC/boards: this option
was nonsense.
Reported-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch overrides default macb pinctrl config defined in
at91sam9260.dtsi (pinctrl_macb_rmii) with kizbox board config
(pinctrl_macb_rmii + pinctrl_macb_rmii_mii_alt).
Signed-off-by: Boris BREZILLON <linux-arm@overkiz.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Make BGA as the default version as we are supposed to just have
to specify when we use the PQFP version.
Issue was existing since commit:
3e90772 (ARM: at91: fix at91rm9200 soc subtype handling).
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: stable <stable@vger.kernel.org> [v3.3]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The gpio controller on kirkwood can provide interrupts but is missing
the #interrupt-cells property. This patch just adds it to both gpio
controllers.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
From Tony Lindgren:
Minimal omap fixes for the -rc series:
- A build fix for recently merged omap DRM changes
- Regression fixes from the common clock framework conversion
for omap4 audio and omap2 reboot
- Regression fix for pandaboard WLAN control UART muxing caused by
u-boot only muxing essential pins nowadays
- Timer iteration fix for CONFIG_OF_DYNAMIC
- A section mismatch fix for ocp2scp init
* tag 'omap-for-v3.8-rc4/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (306 commits)
ARM: OMAP2+: omap4-panda: add UART2 muxing for WiLink shared transport
ARM: OMAP2+: DT node Timer iteration fix
ARM: OMAP2+: Fix section warning for omap_init_ocp2scp()
ARM: OMAP2+: fix build break for omapdrm
ARM: OMAP2: Fix missing omap2xxx_clkt_vps_late_init function calls
ARM: OMAP4: hwmod_data: Correct IDLEMODE for McPDM
ARM: OMAP4: clock data: Lock ABE DPLL on all revisions
+ Linux 3.8-rc4
Signed-off-by: Olof Johansson <olof@lixom.net>
From Sascha Hauer:
ARM i.MX fixes for -rc.
This contains a single compilation fix for the CODA driver.
* tag 'imx-fixes-rc' of git://git.pengutronix.de/git/imx/linux-2.6:
[media] coda: Fix build due to iram.h rename
Add the UART2 muxing data to the board file (this used to be,
erroneously, done in the bootloader).
Cc: stable <stable@vger.kernel.org> [3.7]
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The iterator correctly handles of_node_put() calls.
Remove it before continue'ing the loop.
Without this patch you get the following with
CONFIG_OF_DYNAMIC set:
ERROR: Bad of_node_put() on /ocp/timer@44e31000!
[<c001329c>] (unwind_backtrace+0x0/0xe0) from [<c03dd8f0>] (of_node_release+0x2c/0xa0)!
[<c03dd8f0>] (of_node_release+0x2c/0xa0) from [<c03ddea0>] (of_find_matching_node_and_match+0x78/0x90)!
[<c03ddea0>] (of_find_matching_node_and_match+0x78/0x90) from [<c06d349c>] (omap_get_timer_dt+0x78/0x90)!
[<c06d349c>] (omap_get_timer_dt+0x78/0x90) from [<c06d3664>] (omap_dm_timer_init_one.clone.2+0x34/0x2bc)!
[<c06d3664>] (omap_dm_timer_init_one.clone.2+0x34/0x2bc) from [<c06d3a2c>] (omap2_gptimer_clocksource_init.clone.4+0x24/0xa8)!
[<c06d3a2c>] (omap2_gptimer_clocksource_init.clone.4+0x24/0xa8) from [<c06cca58>] (time_init+0x20/0x30)!
[<c06cca58>] (time_init+0x20/0x30) from [<c06c9690>] (start_kernel+0x1a8/0x2fc)!
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Acked-by: Jon Hunter <jon-hunter@ti.com>
[tony@atomide.com: updated description per Jon]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise we will get:
WARNING: vmlinux.o(.text+0x1d4f0): Section mismatch in reference from the
function omap_init_ocp2scp() to the function .init.text:omap_device_build()
The function omap_init_ocp2scp() references
the function __init omap_device_build().
This is often because omap_init_ocp2scp lacks a __init
annotation or the annotation of omap_device_build is wrong.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 8fb54284ba {ARM: mm: Add strongly ordered descriptor support}
added XN flag at section level but missed it at PTE level.
Fix it by adding the L_PTE_XN to MT_MEMORY_SO PTE descriptor.
Reported-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Subhash Jadavani reported this partial backtrace:
Now consider this call stack from MMC block driver (this is on the ARMv7
based board):
[<c001b50c>] (v7_dma_inv_range+0x30/0x48) from [<c0017b8c>] (dma_cache_maint_page+0x1c4/0x24c)
[<c0017b8c>] (dma_cache_maint_page+0x1c4/0x24c) from [<c0017c28>] (___dma_page_cpu_to_dev+0x14/0x1c)
[<c0017c28>] (___dma_page_cpu_to_dev+0x14/0x1c) from [<c0017ff8>] (dma_map_sg+0x3c/0x114)
This is caused by incrementing the struct page pointer, and running off
the end of the sparsemem page array. Fix this by incrementing by pfn
instead, and convert the pfn to a struct page.
Cc: <stable@vger.kernel.org>
Suggested-by: James Bottomley <JBottomley@Parallels.com>
Tested-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
During the migration to the common clock framework, calls to the
functions omap2xxx_clkt_vps_late_init() were not preserved for
OMAP2420 and OMAP2430. This causes the variables "sys_ck_rate" and
"curr_prcm_set" to be uninitialised on boot. On reboot, this causes the
following error message to be displayed because the appropriate MPU
clock frequency (derived from sys_ck_rate) cannot be found.
"Could not set MPU rate to 4294MHz"
Fix this by adding back calls to omap2xxx_clkt_vps_late_init() in the
OMAP2420 and OMAP2430 clock initialisation code.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
[paul@pwsan.com: dropped the duplicated call to
omap2xxx_clkt_vps_check_bootloader_rates() after consultation with Jon;
updated patch description]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
McPDM need to be configured to NO_IDLE mode when it is in used otherwise
vital clocks will be gated which results 'slow motion' audio playback.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[paul@pwsan.com: copy patch description into hwmod data comments]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
To avoid issues with audio caused by non locked ABE DPLL we should
make sure it is locked in all OMAP4 revisions.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jon Hunter <jon-hunter@ti.com>
[paul@pwsan.com: cleaned up patch description]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
As we use platform_device_id for fsl-usb2-udc driver, it needs to
change clk connection-id, or the related devm_clk_get will be failed.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
As mach/hardware.h is deleted, we need to use platform_device_id to
differentiate SoCs. Besides, one cpu_is_mx35 is useless as it has
already used pdata to differentiate runtime
Meanwhile we update the platform code accordingly.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
From Kukjin Kim:
That branch fixes build error for S3C24XX/S3C64xx. And corrects dw-mshc
properties on EXYNOS5 DT and fixes IRQ mapping on Cragganmore board.
* 'v3.8-samsung-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: S3C64XX: Fix up IRQ mapping for balblair on Cragganmore
ARM: dts: correct the dw-mshc timing properties as per binding
ARM: S3C64XX: Fix build error with CONFIG_S3C_DEV_FB disabled
+ Linux 3.8-rc3
Signed-off-by: Olof Johansson <olof@lixom.net>
As per the current exynos-dw-mshc bindings, dw-mshc-sdr-timing and
dw-mshc-ddr-timing properties are having only two cells, these properties
are wrongly set for exynos5250 based cros5250 and smdk5250 platfroms. This
patch corrects above timing propreties for above platfroms
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Doug Anderson <dianders@chromium.org>
Acked-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
If there is no board selecting CONFIG_S3C_DEV_FB enabled, build will
fail on arch/arm/mach-s3c64xx/pm.c, where s3c_device_fb is referenced.
This patch adds ifdef guard around the code making it compile only
when CONFIG_S3C_DEV_FB is enabled.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
debug_ll_addr is only used on machines with an MMU so it can be #ifdef'ed
out safely. This fixes:
arch/arm/kernel/debug.S: Assembler messages:
arch/arm/kernel/debug.S:104: Error: too many positional arguments
The problem was introduced in e5c5f2a ARM: implement debug_ll_io_init().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
From Maxime Ripard:
Sunxi dt fixes for 3.8-rc's
* tag 'sunxi-fixes-for-3.8-rc4' of git://github.com/mripard/linux:
ARM: sunxi: Use the Synosys APB UART instead of ns8250
Pull second round of sound fixes from Takashi Iwai:
"Yet a few more fixes popped up in this week.
The biggest change here is the addition of pinctrl support for Atmel,
which turned out to be almost mandatory to make things working.
The rest are a few fixes for M-Audio usb-audio device and a fix for
regression of HD-audio HDMI codecs with alsactl in the recent kernel."
* tag 'sound-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/hdmi - Work around "alsactl restore" errors
ALSA: usb-audio: selector map for M-Audio FT C400
ALSA: usb-audio: M-Audio FT C400 skip packet quirk
ALSA: usb-audio: correct M-Audio C400 clock source quirk
ALSA: usb - fix race in creation of M-Audio Fast track pro driver
ASoC: atmel-ssc: add pinctrl selection to driver
ARM: at91/dts: add pinctrl support for SSC peripheral
The UART controller used in the A10/A13 is the Synopsys DesignWare 8250.
The wrong use of a regular 8250 driver may lead to a oops during kernel
boot with "irq 17: nobody cared", because the apb UART as an extra
interrupt that gets raised when writing to the LCR when busy.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
We currently use a temporary 1MB section aligned to a 1MB boundary for
mapping the provided device tree until the final page table is created.
However, if the device tree happens to cross that 1MB boundary, the end
of it remains unmapped and the kernel crashes when it attempts to access
it. Given no restriction on the location of that DTB, it could end up
with only a few bytes mapped at the end of a section.
Solve this issue by mapping two consecutive sections.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Tomasz Figa <t.figa@samsung.com>
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patrik Kluba reports that the preempt count becomes invalid due
to the preempt_enable() call being unbalanced with a
preempt_disable() call in the vfp assembly routines. This happens
because preempt_enable() and preempt_disable() update preempt
counts under PREEMPT_COUNT=y but the vfp assembly routines do so
under PREEMPT=y. In a configuration where PREEMPT=n and
DEBUG_ATOMIC_SLEEP=y, PREEMPT_COUNT=y and so the preempt_enable()
call in VFP_bounce() keeps subtracting from the preempt count
until it goes negative.
Fix this by always using PREEMPT_COUNT to decided when to update
preempt counts in the ARM assembly code.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reported-by: Patrik Kluba <pkluba@dension.com>
Tested-by: Patrik Kluba <pkluba@dension.com>
Cc: <stable@vger.kernel.org> # 2.6.30
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
From Shawn Guo:
It's the second batch of fixes for 3.8, which includes one fixing for
!CONFIG_SMP build, two patches fixing broken imxfb driver caused by
multiplatform conversion, and a couple of pm/hotplug fixes.
* tag 'imx-fixes-3.8-2' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: imx: correct low-power mode setting
ARM: imx: disable cpu in .cpu_kill hook
video: imxfb: fix imxfb_info configuration order
ARM: imx: platform-imx-fb: modifies platform device name
ARM: imx: fix build error with !CONFIG_SMP
Signed-off-by: Olof Johansson <olof@lixom.net>
ASoC: atmel: Fixes for pinctrl
Due to a series of problems with the handling of Atmel, a combination of
making changes that make other branches instantly buggy and a general
failure to deal with the resulting issues effectively, v3.8 Atmel audio
currently won't work at all for DT boards without adding pinctrl
definitions and a request for those.
Pull devicetree fixes from Rob Herring:
"Two fixes to prevent unconditional re-compile of dts files on arm and
arm64."
* tag 'dt-fixes-for-3.8' of git://sources.calxeda.com/kernel/linux:
ARM: dts: prevent *.dtb from always being rebuilt
arm64: dts: prevent *.dtb from always being rebuilt
The hardware reset value of bit CCM_CLPCR_LPM enables WAIT mode
(WAIT_UNCLOCKED) by default. However this is undesirable because
WAIT mode should only be enabled when there is a driver managing
ARM clock gating. Correct the initial power mode to WAIT_CLOCKED
(disable WAIT mode). While at it, the power mode after resuming
is also set back to WAIT_CLOCKED from STOP_POWER_OFF.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
It's buggy to disable the cpu that is being hot-unplugged in .cpu_die
hook which runs on the cpu itself. Instead, it should be done in
.cpu_kill which runs on the thread (another cpu) that asks for shutting
down the cpu. Move imx_enable_cpu(cpu, false) call into .cpu_kill
hook, and leave the cpu to be hot-unplugged in WFI within .cpu_die,
so that we can get a more stable cpu hot-plug operation.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
if_changed (used by the *.dts->*.dtc rule) rebuilds files if they aren't
contained in $(targets). (make V=2 indicates this). Add $(dtb-y) to
$(targets) to prevent *.dtb from always being rebuilt.
This fixes a regression introduced by the .dtb rule rework in 499cd82
"ARM: dt: change .dtb build rules to build in dts directory".
Reported-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Framebuffer platform device is now identified by a device id (imx1-fb or
imx21-fb) instead of by driver name (imx-fb).
Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add pinctrl support for SSC on AT91 dtsi files.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
[nicolas.ferre@atmel.com: split dtsi and driver changes]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Reluctantly-acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
