On sinks with a DPCD rev of 1.1 or greater, we can send sink power
management commands to address 0x600 per section 5.1.5 of the
DisplayPort 1.1a spec.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
When checking link status during a hot plug event or detecting sink
presence, we need to retry 3 times per the spec (section 9.1 of the 1.1a
DisplayPort spec). Consolidate the retry code into a
native_aux_read_retry function for use by get_link_status and _detect.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
We currently use this when a hot plug event is received, only checking
the link status and re-training if we had previously configured a link.
However if we want to preserve the DP configuration across both hot plug
and DPMS events (which we do for userspace apps that don't respond to
hot plug uevents), we need to unconditionally check the link and try to
bring it up on hot plug.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
If ->detect is called too soon after a hot plug event, the sink may not
be ready yet. So try up to 3 times with 1ms sleeps in between tries to
get the data (spec dictates that receivers must be ready to respond within
1ms and that sources should try 3 times).
See section 9.1 of the 1.1a DisplayPort spec.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
When a hotplug event is received, we need to check the receiver cap bits
in case they've changed (as they might with a hub or chain config).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Makes it easier to search for DP related constants.
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
Especially after a hotplug or power status change, the sink may not
reply immediately to a link status query. So retry 3 times per the spec
to really make sure nothing is there.
See section 9.1 of the 1.1a DisplayPort spec.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Now that we track bpp on a per-pipe basis, we can use the actual value
rather than assuming 24bpp.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
The pipe may be driving various bpp values depending on the display
configuration, so take that into account when calculating link bandwidth
requirements.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
Make the audio property creation routine common and share the single
property between the connectors.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Given that the hardware may be left in a random condition by the BIOS,
it is conceivable that we then attempt to clear the DP_PIPEB_SELECT bit
without us ever enabling/attaching the DP encoder to a pipe. Thus
causing a NULL deference when we attempt to wait for a vblank on that
crtc.
Reported-and-tested-by: Bryan Christ <bryan.christ@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=36314
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=36456
Reported-and-tested-by: Bo Wang <bo.b.wang@intel.com>
Cc: stable@kernel.org
Signed-off-by: Keith Packard <keithp@keithp.com>
The order of the calls does matter indeed. Swapping the call order of
intel_dp_destroy() and intel_dp_encoder_destroy() fixes the problem.
This is because i2c_del_adapter unregisters the device which parent is
intel_connector, and connectors are removed in intel_dp_destroy(). Thus
intel_dp_encoder_destroy() must be called before intel_dp_destroy().
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=24822
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Some hardware claims to have both an LVDS panel and an eDP output.
Whilst this may be true in a rare case, more often it is just broken
hardware. If we see an eDP device we know that it must be connected and
so we can confirm its existence with a simple probe.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=34165
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=24822
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
In order to prevent "crushed blacks" on TVs, the range of the RGB output
may be limited to 16-235. This used to be available through Xorg under
the "Broadcast RGB" option, so reintroduce support for KMS.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=34543
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Grab the latest stabilisation bits from -fixes and some suspend and
resume fixes from linus.
Conflicts:
drivers/gpu/drm/i915/i915_drv.h
drivers/gpu/drm/i915/i915_irq.c
Share the lid detection code for the all panels for consistent behaviour
and a single place to add the eventual quirks for crap hardware.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
If the user changes the force-audio property and it no longer reflects
the current configuration, then we need to trigger a mode set in order
to update the registers.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We had some conversions over to the _PIPE macros, but didn't get
everything. So hide the per-pipe regs with an _ (still used in a few
places for legacy) and add a few _PIPE based macros, then make sure
everyone uses them.
[update: remove usage of non-existent no-op macro]
[update 2: keep modesetting suspend/resume code, update to new reg names]
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[ickle: stylistic cleanups for checkpatch and taste]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Rather than power cycling the panel when there are no bits to display,
use the VDD AUX bit to power the panel up just enough for DP AUX
transactions to work. This prevents a bit of unnecessary ugliness as
mode sets occur on the panel.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Now that we're doing the right thing elsewhere, these are no longer
necessary.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=31114
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Some voltage swing/pre-emphasis level use the same value on eDP
Sandybridge, like 400mv_0db and 600mv_0db are with the same value
of (0x0 << 22). So, fix them, and point out the value if it isn't
a supported voltage swing/pre-emphasis level.
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
When trying to do channel equalization, we need to make sure we still
have clock recovery on all lanes while training. We also need to try
clock recovery again if we lose the clock or if channel eq fails 5
times. We'll try clock recovery up to 5 more times before giving up
entirely.
Gets suspend/resume working on my Vaio again and brings us back into
compliance with the DP training sequence spec.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The DisplayPort standard (1.1a) states that:
The I2C-over-AUX Reply field is valid only when Native AUX CH Reply
field is AUX_ACK (00). When Native AUX CH Reply field is not 00, then,
I2C-over-AUX Reply field must be 00 and be ignored.
This fixes broken EDID reading when using an active DisplayPort to
duallink DVI converter. If the AUX CH replier chooses to defer the
transaction, a short read occurs and erroneous data is returned as
the i2c reply due to a lack of length checking and failure to check
for AUX ACK.
As a result, broken EDIDs can look like:
0 1 2 3 4 5 6 7 8 9 a b c d e f 0123456789abcdef
00: bc bc bc ff bc bc bc ff bc bc bc ac bc bc bc 45 ???.???.???????E
10: bc bc bc 10 bc bc bc 34 bc bc bc ee bc bc bc 4c ???????4???????L
20: bc bc bc 50 bc bc bc 00 bc bc bc 40 bc bc bc 00 ???P???.???@???.
30: bc bc bc 01 bc bc bc 01 bc bc bc a0 bc bc bc 40 ???????????????@
40: bc bc bc 00 bc bc bc 00 bc bc bc 00 bc bc bc 55 ???.???.???.???U
50: bc bc bc 35 bc bc bc 31 bc bc bc 20 bc bc bc fc ???5???1??? ????
60: bc bc bc 4c bc bc bc 34 bc bc bc 46 bc bc bc 00 ???L???4???F???.
70: bc bc bc 38 bc bc bc 11 bc bc bc 20 bc bc bc 20 ???8??????? ???
80: bc bc bc ff bc bc bc ff bc bc bc ff bc bc bc ff ???.???.???.???.
...
which can lead to:
[drm:drm_edid_block_valid] *ERROR* EDID checksum is invalid, remainder
[drm:drm_edid_block_valid] *ERROR* Raw EDID:
<3>30 30 30 30 30 30 30 32 38 32 30 32 63 63 31 61 000000028202cc1a
<3>28 00 02 8c 00 00 00 00 18 00 00 00 00 00 00 00 (...............
<3>20 4c 61 73 74 20 62 65 61 63 6f 6e 3a 20 33 32 Last beacon: 32
<3>32 30 6d 73 20 61 67 6f 46 00 05 8c 00 00 00 00 20ms agoF.......
<3>36 00 00 00 00 00 00 00 00 0c 57 69 2d 46 69 20 6.........Wi-Fi
<3>52 6f 75 74 65 72 01 08 82 84 8b 96 24 30 48 6c Router......$0Hl
<3>03 01 01 06 02 00 00 2a 01 00 2f 01 00 32 04 0c .......*../..2..
<3>12 18 60 dd 09 00 10 18 02 00 00 01 00 00 18 00 ..`.............
Signed-off-by: David Flynn <davidf@rd.bbc.co.uk>
[ickle: fix up some surrounding checkpatch warnings]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
As we may try to power down the link at various times, it is not
necessarily still coupled with an encoder and so we must be careful not
to depend upon an operation that is only valid when the link is still
attached to a pipe.
Fixes regression in 5bddd17.
Reported-and-tested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org [after applying 5bddd17]
This workaround only applies to Ironlake.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
This reverts commit 869184a675.
This is required for the Sony Vaio Jesse was working on at the time, but
breaks most other eDP machines - machines that were working in earlier
kernels.
Reported-and-tested-by: Dave Airlie <airlied@redhat.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=31188
Tested-by: Zhao Jian <jian.j.zhao@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Hi,
while I looked through your changes in drm-intel git tree (as I've got
a pressure for supporting DisplayPort audio), I stumbled on the
possible bug in the commit a9756bb5b2
Author: Zhenyu Wang <zhenyuw@linux.intel.com>
Date: Sun Sep 19 13:09:06 2010 +0800
drm/i915: Enable DisplayPort audio
In this commit, you changed the return value of g4x_dp_detect()
to "bit", but it should be "status", I suppose.
[ickle: mea culpa.]
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=31094
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Allow the user to override the detection of the sink's audio capabilities
from EDID. Not all sinks support the required EDID level to specify
whether they handle audio over the display connection, so allow the user
to enable it manually.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This will turn on DP audio output by checking monitor's audio
capability.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
[ickle: rebase onto recent changes and rearranged for clarity]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Since the PLL may still be on, and the training pattern may not be
correct. Fixes suspend/resume on my PCH eDP test system.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[ickle: minor merge conflict and silence the compiler]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We don't use the CPU DP PLL with PCH attached eDP panels, so don't
bother to enable it.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We can skip most of the link training step if we use the VBT provided
values.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cache the first 4 bytes of DPCD data in the eDP case. It's unlikely to
change and can save us some trouble at link training time.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Enable the panel before adjusting eDP link params, make sure the panel
is idle after powering it on before proceeding with other activity,
delay backlight enable to avoid visible flicker.
Also avoid using VDD per hw team recommendation; it can conflict with
the builtin panel power sequencing logic and lead to panel power
sequencing failures.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Since we set the output type of PCH attached eDP panels to
INTEL_OUTPUT_eDP this function would never return true when it should.
It's been replaced by working functions.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The display code needs to distinguish between CPU and PCH attached eDP
panels, so add some helpers to handle that.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
With the old check we'd never set lane_count or bpp to different values
on PCH attached eDP panels.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
If is_edp is true, is_pch_edp will always be true. So limit the calls
to the latter function to places where the distinction actually matters.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Most of the PCH eDP checks are redundant, so document the functions in
preparation for removing most of the calls.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The display port DPMS state is tracked internally in the display port
driver so that when a hotplug event comes along, the driver can know
whether to try retraining the link. This doesn't work well if the
driver never sets the DPMS state to ON when the output is enabled.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
While the display port is in training mode, vblank interrupts don't
occur. Because we have to wait for the display port output to turn on
before starting the training sequence, enable the output in 'normal'
mode so that we can tell when a vblank has occurred, then start the
training sequence.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This patch fixes the black screen bug on Dell e6510, by
adding two delays to give the eDP panel time to turn on before we
continue with the next write.
300ms is rather arbitray and a rather long sleep, we need to find a way
of refining this value.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=29278
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
First step, lets have a look at the values for troublesome panels and
see if they may be used to improve our link training.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
