This is a patch to fix an issue with the HID gadget which, at the moment,
returns STALL on a HID descriptor request. Essentially, the patch changes
the hid gadget such that a request for the HID descriptor is handled by
copying the descriptor into the response buffer, rather than falling
through the default case, in which the request is answered by a STALL.
Signed-off-by: Sebastian Bauer <mail@sebastianbauer.info>
Acked-by: Peter Korsgaard <peter.korsgaard@barco.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
After 622859634 (usb: musb: drop a gigantic amount of ifdeferry):
- USB_GADGET_MUSB_HDRC is no longer selectable because it
depends on the removed USB_MUSB_PERIPHERAL and USB_MUSB_OTG
options
- The Kconfig comment still says "Enable Host or Gadget support
to see Inventra options", even though you now need to enable
both of them to see Inventra options.
Fix the dependency and drop the anyway unnecessary comment.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Felipe Balbi <balbi@ti.com>
For bMaxPacketSize0 we usually take what is specified in ep0->maxpacket.
This is fine in most cases, however on SuperSpeed bMaxPacketSize0
specifies the exponent instead of the actual size in bytes. The only
valid value on SS is 9 which denotes 512 bytes.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The code in this block is unused and the Author is fine with removing:
| These functions were used to debug unstable hw fifo while developing
| fusb300. It's much more stable now.
| So these functions can be removed.
Cc: "Wendy Yuan-Hsin Chen" <yhchen@faraday-tech.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
platform_device_id structures need a NULL terminating
entry, add it.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (430 commits)
[media] ir-mce_kbd-decoder: include module.h for its facilities
[media] ov5642: include module.h for its facilities
[media] em28xx: Fix DVB-C maxsize for em2884
[media] tda18271c2dd: Fix saw filter configuration for DVB-C @6MHz
[media] v4l: mt9v032: Fix Bayer pattern
[media] V4L: mt9m111: rewrite set_pixfmt
[media] V4L: mt9m111: fix missing return value check mt9m111_reg_clear
[media] V4L: initial driver for ov5642 CMOS sensor
[media] V4L: sh_mobile_ceu_camera: fix Oops when USERPTR mapping fails
[media] V4L: soc-camera: remove soc-camera bus and devices on it
[media] V4L: soc-camera: un-export the soc-camera bus
[media] V4L: sh_mobile_csi2: switch away from using the soc-camera bus notifier
[media] V4L: add media bus configuration subdev operations
[media] V4L: soc-camera: group struct field initialisations together
[media] V4L: soc-camera: remove now unused soc-camera specific PM hooks
[media] V4L: pxa-camera: switch to using standard PM hooks
[media] NetUP Dual DVB-T/C CI RF: force card hardware revision by module param
[media] Don't OOPS if videobuf_dvb_get_frontend return NULL
[media] NetUP Dual DVB-T/C CI RF: load firmware according card revision
[media] omap3isp: Support configurable HS/VS polarities
...
Fix up conflicts:
- arch/arm/mach-omap2/board-rx51-peripherals.c:
cleanup regulator supply definitions in mach-omap2
vs
OMAP3: RX-51: define vdds_csib regulator supply
- drivers/staging/tm6000/tm6000-alsa.c (trivial)
The driver had to decide how many events to allocate when the v4l2_fh struct
was created. It was possible to add more events afterwards, but there was no
way to ensure that you wouldn't miss important events if the event queue
would fill up for that filehandle.
In addition, once there were no more free events, any new events were simply
dropped on the floor.
For the control event in particular this made life very difficult since
control status/value changes could just be missed if the number of allocated
events and the speed at which the application read events was too low to keep
up with the number of generated events. The application would have no idea
what the latest state was for a control since it could have missed the latest
control change.
So this patch makes some major changes in how events are allocated. Instead
of allocating events per-filehandle they are now allocated when subscribing an
event. So for that particular event type N events (determined by the driver)
are allocated. Those events are reserved for that particular event type.
This ensures that you will not miss events for a particular type altogether.
In addition, if there are N events in use and a new event is raised, then
the oldest event is dropped and the new one is added. So the latest event
is always available.
This can be further improved by adding the ability to merge the state of
two events together, ensuring that no data is lost at all. This will be
added in the next patch.
This also makes it possible to allow the user to determine the number of
events that will be allocated. This is not implemented at the moment, but
would be trivial.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Drivers that supported events used to be rare, but now that controls can also
raise events this will become much more common since almost all drivers have
controls.
This means that keeping struct v4l2_events as a separate struct make no more
sense. Merging it into struct v4l2_fh simplifies things substantially as it
is now an integral part of the filehandle struct.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (115 commits)
EHCI: fix direction handling for interrupt data toggles
USB: serial: add IDs for WinChipHead USB->RS232 adapter
USB: OHCI: fix another regression for NVIDIA controllers
usb: gadget: m66592-udc: add pullup function
usb: gadget: m66592-udc: add function for external controller
usb: gadget: r8a66597-udc: add pullup function
usb: renesas_usbhs: support multi driver
usb: renesas_usbhs: inaccessible pipe is not an error
usb: renesas_usbhs: care buff alignment when dma handler
USB: PL2303: correctly handle baudrates above 115200
usb: r8a66597-hcd: fixup USB_PORT_STAT_C_SUSPEND shift
usb: renesas_usbhs: compile/config are rescued
usb: renesas_usbhs: fixup comment-out
usb: update email address in ohci-sh and r8a66597-hcd
usb: r8a66597-hcd: add function for external controller
EHCI: only power off port if over-current is active
USB: mon: Allow to use usbmon without debugfs
USB: EHCI: go back to using the system clock for QH unlinks
ehci: add pci quirk for Ordissimo and RM Slate 100 too
ehci: refactor pci quirk to use standard dmi_check_system method
...
Fix up trivial conflicts in Documentation/feature-removal-schedule.txt
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
fs: Merge split strings
treewide: fix potentially dangerous trailing ';' in #defined values/expressions
uwb: Fix misspelling of neighbourhood in comment
net, netfilter: Remove redundant goto in ebt_ulog_packet
trivial: don't touch files that are removed in the staging tree
lib/vsprintf: replace link to Draft by final RFC number
doc: Kconfig: `to be' -> `be'
doc: Kconfig: Typo: square -> squared
doc: Konfig: Documentation/power/{pm => apm-acpi}.txt
drivers/net: static should be at beginning of declaration
drivers/media: static should be at beginning of declaration
drivers/i2c: static should be at beginning of declaration
XTENSA: static should be at beginning of declaration
SH: static should be at beginning of declaration
MIPS: static should be at beginning of declaration
ARM: static should be at beginning of declaration
rcu: treewide: Do not use rcu_read_lock_held when calling rcu_dereference_check
Update my e-mail address
PCIe ASPM: forcedly -> forcibly
gma500: push through device driver tree
...
Fix up trivial conflicts:
- arch/arm/mach-ep93xx/dma-m2p.c (deleted)
- drivers/gpio/gpio-ep93xx.c (renamed and context nearby)
- drivers/net/r8169.c (just context changes)
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (107 commits)
vfs: use ERR_CAST for err-ptr tossing in lookup_instantiate_filp
isofs: Remove global fs lock
jffs2: fix IN_DELETE_SELF on overwriting rename() killing a directory
fix IN_DELETE_SELF on overwriting rename() on ramfs et.al.
mm/truncate.c: fix build for CONFIG_BLOCK not enabled
fs:update the NOTE of the file_operations structure
Remove dead code in dget_parent()
AFS: Fix silly characters in a comment
switch d_add_ci() to d_splice_alias() in "found negative" case as well
simplify gfs2_lookup()
jfs_lookup(): don't bother with . or ..
get rid of useless dget_parent() in btrfs rename() and link()
get rid of useless dget_parent() in fs/btrfs/ioctl.c
fs: push i_mutex and filemap_write_and_wait down into ->fsync() handlers
drivers: fix up various ->llseek() implementations
fs: handle SEEK_HOLE/SEEK_DATA properly in all fs's that define their own llseek
Ext4: handle SEEK_HOLE/SEEK_DATA generically
Btrfs: implement our own ->llseek
fs: add SEEK_HOLE and SEEK_DATA flags
reiserfs: make reiserfs default to barrier=flush
...
Fix up trivial conflicts in fs/xfs/linux-2.6/xfs_super.c due to the new
shrinker callout for the inode cache, that clashed with the xfs code to
start the periodic workers later.
Btrfs needs to be able to control how filemap_write_and_wait_range() is called
in fsync to make it less of a painful operation, so push down taking i_mutex and
the calling of filemap_write_and_wait() down into the ->fsync() handlers. Some
file systems can drop taking the i_mutex altogether it seems, like ext3 and
ocfs2. For correctness sake I just pushed everything down in all cases to make
sure that we keep the current behavior the same for everybody, and then each
individual fs maintainer can make up their mind about what to do from there.
Thanks,
Acked-by: Jan Kara <jack@suse.cz>
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
M66592 has the pin of WR0 and WR1. So, if one write-pin of CPU
connects to the pins, we have to change the setting of FIFOSEL
register in the controller. If we don't change the setting,
the controller cannot send the data of odd length.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch rescues renesas_usbhs compile from
commit 193ab2a (usb: gadget: allow multiple gadgets to be built)
CONFIG_USB_RENESAS_USBHS compile renesas_usbhs main code which
is shared between Host/Gadget.
CONFIG_USB_RENESAS_USBHS_UDC add mod_gadget to it.
It had lost USB_GADGET_DUALSPEED
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds SuperSpeed descriptors to the
g_zero gadget.
The SuperSpeed descriptors were added both for
f_soursesink and f_loopback function drivers.
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
Signed-off-by: Amit Blay <ablay@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add SuperSpeed descriptors to the Network USB
function drivers.
This has been lightly tested using a Linux host.
I was able to ssh from device to host and host to
device, no obvious problems seen.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The USB high speed device must support the TEST_MODE, but the driver
didn't support it. When we sent the SET_FEATURE for TEST_MODE to
the driver, the request was successful, but the module didn't enter
the TEST_MODE.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The USB high speed device must support the TEST_MODE, but the driver
didn't support it. When we sent the SET_FEATURE for TEST_MODE to
the driver, the request was successful, but the module didn't enter
the TEST_MODE.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
BUSWAIT is a 4-bit-wide value that controls the number of access waits
from the CPU to on-chip USB module. b'0000 inserts 0 wait (2 access
cycles) and b'1111 inserts 15 waits (17 access cycles, hardware
initial value), respectively.
BUSWAIT value depends on peripheral clock frequency supplied to on-chip
of each CPU, hence should be configurable through platform data.
Note that this patch assumes that b'0000 (0 wait, 2 access cycles) is
rerely used and considered as invalid. If valid 'buswait' data is not
provided by platform, initial b'1111 (15 waits, 17 access cycles) will
be applied as a safe default.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When we run rmmod a gadget driver, the driver will call
disable_controller(). Then, because the bit of USBE in SYSCFG0 was
cleared in on_chip=1 mode, we could not connect the usb when we run
insmod a gadget driver next time.
This patch also cleans up probe() and ->stop() about unnecessary
init_controller().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Both fusb300 and langwell udcs seem to only
work with 32-bit address space.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
- remove pointer u32 abuse in fusb300_fill_idma_prdtbl().
It is assigned the dma_addr to a pointer and then back.
Poor families may have to recycle variables but we don't
- don't free req.buf in error case. We don't do it in the
ok case so it is probably wrong to do it in error case.
- return in error case. There is no reason to continue
without data and performing ops on an invalid pointer.
- The if (d) statement is bogus since an invalid DMA pointer
is ~0 on some architecutres. And since we return for the
invalid case we don't need it.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix the following compile warning:
| usb/gadget/ci13xxx_udc.c: In function 'show_registers':
| usb/gadget/ci13xxx_udc.c:1242:1: warning: the frame size of 2064 bytes is larger than 1024 bytes
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes the following compile warnings:
drivers/usb/gadget/net2272.c: In function ‘net2272_kick_dma’:
drivers/usb/gadget/net2272.c:740:2: warning: format ‘%x’ expects argument of type ‘unsigned int’, but argument 6 has type ‘dma_addr_t’ [-Wformat]
drivers/usb/gadget/net2272.c: In function ‘net2272_queue’:
drivers/usb/gadget/net2272.c:859:2: warning: format ‘%x’ expects argument of type ‘unsigned int’, but argument 8 has type ‘dma_addr_t’ [-Wformat]
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes the following compile warnings:
drivers/usb/gadget/langwell_udc.c: In function ‘queue_dtd’:
drivers/usb/gadget/langwell_udc.c:596:2: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
drivers/usb/gadget/langwell_udc.c: In function ‘langwell_udc_probe’:
drivers/usb/gadget/langwell_udc.c:3274:2: warning: format ‘%d’ expects argument of type ‘int’, but argument 4 has type ‘size_t’ [-Wformat]
drivers/usb/gadget/langwell_udc.c:3289:2: warning: format ‘%d’ expects argument of type ‘int’, but argument 4 has type ‘size_t’ [-Wformat]
drivers/usb/gadget/langwell_udc.c: In function ‘langwell_udc_resume’:
drivers/usb/gadget/langwell_udc.c:3473:2: warning: format ‘%d’ expects argument of type ‘int’, but argument 4 has type ‘size_t’ [-Wformat]
drivers/usb/gadget/langwell_udc.c:3487:2: warning: format ‘%d’ expects argument of type ‘int’, but argument 4 has type ‘size_t’ [-Wformat]
Signed-off-by: Felipe Balbi <balbi@ti.com>
that code has been dead forever. Since the
first commit (0fe6f1d1) the use of that code
has been commented out. Let's drop the dead
code already and fix the following compile
warning:
| drivers/usb/gadget/fusb300_udc.c: At top level:
| drivers/usb/gadget/fusb300_udc.c:771:13: warning: ‘fusb300_wrfifo’ defined but not used [-Wunused-function]
| drivers/usb/gadget/fusb300_udc.c:1027:13: warning: ‘fusb300_set_ep_bycnt’ defined but not used [-Wunused-function]
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is a bug in Samsung's UDC driver, which is completely disabling
the USB device when a custom UDC command is used.
Following patch seems to get the right behavior (e.g. enabling pull-up
instead of disabling then Vcc is applied).
Signed-off-by: Viliam Mateicka <viliam.mateicka@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A compilation warning was added by the patch
"usb: gadget: use config_ep_by_speed() instead of ep_choose()".
This patch fixed it.
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The recent commit 2edb11cbac fixed req->length in the composite_setup()
function, but that will cause all g_zero tests to fail like:
root#> ./testusb -D /proc/bus/usb/002/021 -t14 -c 15000 -s 256 -v 1
unknown speed /proc/bus/usb/002/021
/proc/bus/usb/002/021 test 14 --> 32 (Broken pipe)
We need to fix req->length in sourcesink_setup() as well to avoid this.
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This was somehow forgotten.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
bind() and pull is moved to udc core, call callbacks are verified by the
upper layer.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
udc_start() should only trigger the internal state machine and make
minimal house keeping. Before that call udc-core calls the bind()
callback and after the callback the pullup().
udc_stop() is simillar, udc-core calls pullup(), unbind() and finally
udc_stop().
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The configuration is static however we only know the speed after we have
connected with the other side.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This value is now assigned during bind(). The configuration depends on
static values assigned by dummy driver itself. So there is no need to
defer this assigment until one know the actuall speed since the
configuration is static and known early.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is only required to be done once. There is no counter part to this
in ->stop() so there is no need to re-do it next time. While here also
init the max_stream size to 0 on SS speed.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
maxpacket is set by the udc driver for ep0 very early. This value is
copied by the function gadget used later for the USB_DT_DEVICE and
USB_DT_DEVICE_QUALIFIER query. This seems to work fine so far. For USB3
we need set a different value here. In SS speed it is 2^x with x=9 and
in HS we set something <= 64. If the UDC starts in SS and continues in
HS after the cable has been plugged it will report a too small value.
There setting of this value is defered and taken automaticly from the
ep0 pointer where the UDC driver can update it according to the speed it
detected _after_ a cable has been plugged.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
now that we have the udc class, we can allow
multiple gadget controller drivers to be
compiled as modules. This will allow for
distro-like kernels for embedded devices.
With this patch, I managed to build an x86
kernel with support for many of the controllers
enabled:
CONFIG_USB_FUSB300=m
CONFIG_USB_R8A66597=m
CONFIG_USB_M66592=m
CONFIG_USB_AMD5536UDC=m
CONFIG_USB_CI13XXX_PCI=m
CONFIG_USB_NET2272=m
CONFIG_USB_NET2280=m
CONFIG_USB_GOKU=m
CONFIG_USB_LANGWELL=m
CONFIG_USB_EG20T=m
Also an ARM kernel with support for many controllers:
CONFIG_USB_FUSB300=m
CONFIG_USB_OMAP=m
CONFIG_USB_R8A66597=m
CONFIG_USB_GADGET_MUSB_HDRC=m
CONFIG_USB_M66592=m
CONFIG_USB_NET2272=m
CONFIG_USB_DUMMY_HCD=m
The next step would be to get rid of the
direct access to arch/ and mach/ directories
on some gadget controllers so that we can
build all of them without depending on their
respective ARCH_* symbols.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This function has no user in my tree. It looks like it belongs to
net2280 but it somehow morphed into the dummy_hcd. So I remove it
before it spreads into more drivers.
After some digging I figured out that the only user was removed in
|commit 9079e91b5b
|Author: David Brownell <david-b@pacbell.net>
|Date: Wed May 7 16:00:36 2008 -0700
|
| USB: serial gadget: cleanup/reorg
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Taking the correct struct once avoids doing the speed dance.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
gadget_to_dummy_hcd() already does the speed check, so
it's unnecessary to unroll that all the time.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
