Added support for Diagnostics MBOX command via BSG Vendor HST_VENDOR
interface. This command provides various tests for validating hardware
functionality.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
While loopback diagnostic is in progress, disable the ACB which resets
all the active connections to target. Disable ACB would filter out all
the DHCP multicast and broadcast packets which otherwise cause the
diagnostic test to take longer time to complete or failures in some
other cases.
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Issue:
Request queue count holds the information about free space in request queue
which has to be manipulated based on request in and out pointer.
But in driver response path, this count was incremented unconditionally,
which could move req_in pointer beyond req_out pointer.
This scenario leads fw hang during IO.
Solution:
Request queue count manipulation has to be done in IO path only, keeping
req_in and req_out pointer two IOCB count away
Signed-off-by: Tej Parkash <tej.parkash@qlogic.com>
Signed-off-by: Shyam Sundar <shyam.sundar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Move "Incorrect function ID" print message in case INTX interrupt
from DEBUG2 to DEBUG7. This will avoid floods of this message if
DEBUG2 is enabled.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Quiesce all different activities performed by driver upon the link events
while loopback diagnostics is in progress.
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The spurious interrupt messages are seen when interrupt lines are
shared between different adapters or modules. Example, interrupt
lines are shared between qlcnic and qla4xxx and USB modules, then the
console is flooded with flurry of spurious interrupt messages
which are expected in such scenario.
Hence put these messages under debug level 2 for INTx interrupt mode.
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Issue:
Mailbox command timed out after switching from polling mode to interrupt mode.
Events:-
1. Mailbox interrupts are disabled
2. FW generates AEN and at same time driver enables Mailbox Interrupt
3. Driver issues new mailbox to Firmware
In above case driver will not get AEN interrupts generated by FW in step #2 as
FW generated this AEN when interrupts are disabled. During the same time
driver enabled the mailbox interrupt, so driver will not poll for interrupt.
Driver will never process AENs generated in step #2 and issues new mailbox to
FW, but now FW is not able to post mailbox completion as AENs generated before
are not processed by driver.
Fix:
Enable Mailbox / AEN interrupts before initializing FW in case of ISP83XX.
This will make sure we process all Mailbox and AENs in interrupt mode.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
For ISP82xx mixed interrupt mode is not supported.
Hence prevent MSI/MSI-x from falling back to INTx mode.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The current code would incorrectly return a DID_OK for a
CHECK CONDITION with Recovered error sense key causing incorrect
completion of a command when there is a dropped frame.
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Tej Parkash <tej.parkash@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Defined error codes for ping completion status.
This patch take care of Mike Christie's commets
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Added ping support for network connection diagnostics.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Added support to post kernel host event to application using
netlink interface.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
For 4032, context reset was the same as chip reset, and any firmware
issue was recovered by performing a chip reset.
For 82xx, the iSCSI firmware runs along with FCoE and the NIC
firmware contexts, and an error encountered doesnot essentially mean
that a chip reset is necessary.
Perform Chip resets only in the following cases:
1. Mailbox system error.
2. Mailbox command timeout.
3. fw_heartbeat_counter counter stops incrementing.
For all other cases, only perform a context reset.
1. Command Completion with an invalid srb.
2. Other mailbox failures.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Shyam Sunder <shyam.sunder@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add scsi_transport_iscsi hooks in qla4xxx to support
iSCSI session management using iscsiadm.
This patch is based on discussion here
http://groups.google.com/group/open-iscsi/browse_thread/thread/e89fd888baf656a0#
Now users can use iscsiadm to do target discovery and do login/logout to
individual targets using the qla4xxx iSCSI class interface.
This patch leaves some dead code, but to make it easier to review
we are leaving and in the next patch we will remove that old code.
V2 - NOTE: Added code to avoid waiting for AEN during login/logout
in the driver, instead added a kernel to user event
to notify iscsid about login status. Because of this
iscsid will not get blocked.
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Complete the cmd if sense length is zero. For cases where sense
data spans across multiple iocb's by FW, we need to hold on to the
I/O (ha->status_srb != NULL) till we have processed them all and
copied the sense data from internal buffer to scsi_cmd sense buffer.
Signed-off-by: Prasanna Mumbai <prasanna.mumbai@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
- Added MBOX_ASTS_DUPLICATE_IP AEN handling.
- Update MBOX_AEN_REG_COUNT to 8 so that driver will save status
of all mbox registers in aen_q
Signed-off-by: Prasanna Mumbai <prasanna.mumbai@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
remove ha flag AF_HBA_GOING_AWAY and added flag AF_HA_REMOVAL
to mark the other ISP-4xxx port to indicate that the driver is
being removed, so that the other port will not re-initialize
while in the process of removing the ha due to driver unload
or hba hotplug.
Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Driver has capability to add device dynamically and present
them to OS, driver no longer need to wait for DDBs to come
online during driver initialization.
Driver still issues a relogin for DDBs that are not online,
but no longer wait for DDB to come online.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Prior to firmware state change from ACQUIRING to READY, an
0x8029 AEN is received. Added code to check previous state
being ACQUIRING in order to update the ip address in the driver.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Prasanna Mumbai <prasanna.mumbai@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
IRQF_SHARED flag should not be set when calling request_irq for MSI since
this interrupt mechanism cannot be shared like standard INTx
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Shyam Sundar <shyam.sundar@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
IRQF_DISABLE flag is deprecated and this flag is a NOOP in kernel.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
AEN 8130 Corresponds to an event representing the insertion (detection)
of a transceiver. It also reports the type of the SFP+.
AEN 8131 corresponds to the removal of a transceiver.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Shyam Sundar <shyam.sundar@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
change data type of sense_len from uint8_t to uint16_t
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Per RFC 3720, Login Response Status Code 0x02 should not be retried.
Condensed connection error checking code to a single routine, and
added check for status class 0x02.
Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Link Down -> Mark all devices missing
Previously, the driver took no action on a Link Down,
and waited for the I/O on a dead connection to timeout
in the firmware before marking the DDB missing.
Link Up -> Mark all devices online
F/W will do auto login to all the devices only once.
After that its the responsibility of the driver to
relogin to devices whenever there is :
* Any sort of connection failure or
* KATO expires indicating target has logged out or
* I/O times out etc.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The residual variable is only valid for udnerrun so do
not print it out for the overrun case.
Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
[Mike Christie: Fix coding style issues in patch]
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fixed sense data errors occurring above the first 32 bytes,
as required by some third party applications. Sense data
in the first 32 bytes has always been correct.
Patch updated to use srb data variables instead of scsi command
scratchpad data area, as scratchpad area is already used.
Also, corrected debug print alignment bug in dump_buffer routine.
Changed KERN_DEBUG to KERN_INFO in printk statements in this routine.
Changed version number to 5.01.00-k9
Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
[michaelc: fixed checkpath.pl errors]
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch converts the iscsi drivers to the new host byte values.
v2
Drop some conversions. Want to avoid conflicts with other patches.
v1
initial patch.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch contains the following:
1. when hba completion status is good, check for iscsi transport
errors (underflow/overflow) prior to checking the scsi status
2. New firmware requires that one marker iocb be issued for each task
management command. The patch issues marker iocb immediately
following a LUN or Target reset.
Signed-off-by: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
