The commit "ath9k: Add custom parameters for CUS198" didn't
pass the correct gpio value to ath9k_hw_cfg_output(). Fix it.
Reported-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When trying to unset a previously-set multicast list (i.e. the new list
has 0 entries), mwifiex_set_multicast_list() was calling down to
mwifiex_request_set_multicast_list() while leaving
mcast_list.num_multicast_addr as an uninitialized value.
We were arriving at mwifiex_cmd_mac_multicast_adr() which would then
proceed to do an often huge memcpy of
mcast_list.num_multicast_addr*ETH_ALEN bytes, causing memory corruption
and hard to debug crashes.
Fix this by setting mcast_list.num_multicast_addr to 0 when no multicast
list is provided. Similarly, fix up the logic in
mwifiex_request_set_multicast_list() to unset the multicast list that
was previously sent to the hardware in such cases.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow a regulatory domain country code to be specified at boot
using a module argument. This overrides the firmware regulatory
mode.
This patch also enables uAP to operate in 11a mode with hostapd.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If "device is disconnected" check occurs to be true in ezusb_access_ltv(),
it just return -ENODEV. But that means request_context is leaked since
there are no any references to it anymore.
The patch adds a call to ezusb_request_context_put() before return.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CUS198 is a card based on AR9485. There are differences
between the base reference design HB125 and CUS198.
Identify such cards based on the PCI subsystem IDs and
set HW parameters appropriately.
Addresses this bug - https://bugzilla.kernel.org/show_bug.cgi?id=49201
Cc: jkp@iki.fi
Cc: gfmichaud@gmail.com
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since raising/lowering the limits based on INI has
been changed, the error limit for OFDM has to be 1000,
not 3500.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the new rate control API, the driver can now apply the
tx rate to outgoing frames just before they are uploaded to
the device. This is important because the rate control can
now react to fading or improving links a bit sooner.
Also, the driver no longer needs to sort the outgoing frames
for sample attempts (which affected the size of A-MPDUs and
the throughput of the link). For aggregated data frames, the
driver (and rate control) needs only to calculate and apply
a single set of tx rates to every subframe of the whole
aggregate.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The fw is unreliable in all the cases in which the packet
wasn't sent.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The older devices (pre-7000/3000 series) all only work with the
DVM opmode due to firmware availability, while newer ones will
only work with the MVM opmode for the same reason.
When building a driver that only has one of MVM or DVM, there's
no reason to build the device support and have the PCIe IDs for
all devices since they can't be used anyway, so avoid that.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Give the scratch area a sub structure so it's marked
explicitly and it is obvious which part it is.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of using #ifdef CONFIG_IWLWIFI_DEBUG, remove the
iwlwifi_mod_params.debug_level variable completely and
make iwl_have_debug_level() always return false in the
non-debug case. This way, the optimiser will elide all
code for it automatically without having to add #ifdefs.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove calibration per-channel data as it's no longer used.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove the unused iwl_mvm *mvm parameter from the
iwl_mvm_send_remote_wake_cfg function in D3.c.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no reason to read the INTA register in the ICT IRQ
handler, this interrupt mechanism is designed to not have
to read as many registers as the regular one. Not reading
the INTA register gives a significant performance/CPU use
improvement.
Since we still want to get this info, fetch it only if
the ISR debug level is enabled.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Added statistics for flow-control and packets dropped by the
driver.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently firmware requested credits do not require fifo credits.
From a buffer management point of view this is incorrect. So
firwmware requested credits require also fifo credits before the
packet can be transferred to the host.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit dd9c46408f.
With "iwl{4965,3495): workaround for firmware frame tx rejection"
patches we can enable IEEE80211_HW_REPORTS_TX_ACK_STATUS again.
Tested-by: Jake Edge <jake@lwn.net>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Firmware can reject to transmit frame on passive channel, when it
did not yet received any frame with valid CRC on that channel.
Workaround this problem in the driver.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Firmware can reject to transmit frame on passive channel, when it
did not yet received any frame with valid CRC on that channel.
Workaround this problem in the driver.
Tested-by: Jake Edge <jake@lwn.net>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add functions that will stop/wake all queues. Make them safe
regarding multiple calls and when some ac are stopped/woke
independently.
Tested-by: Jake Edge <jake@lwn.net>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch enabels ath5k to use the new rate table to lookup each
mrr rate and retry information per packet.
Signed-off-by: Benjamin Vahl <bvahl@net.t-labs.tu-berlin.de>
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ah->noise is maintained globally and not per-channel. This
is updated in the reset() routine after the NF history has been
filled for the *current channel*, just before switching to
the new channel. There is no need to do it inside getnf(), since
ah->noise must contain a value for the new channel.
Cc: stable@vger.kernel.org
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commits,
"ath9k: Fix regression in channelwidth switch at the same channel"
"ath9k: Fix invalid noisefloor reading due to channel update"
attempted to fix noisefloor calibration when a channel switch
happens due to HT20/HT40 bandwidth change. This is causing invalid
readings resulting in messages like:
"ath: phy16: NF[0] (-45) > MAX (-95), correcting to MAX".
This results in an incorrect noise being used initially for reporting
the signal level of received packets, until NF calibration is done
and the history buffer is updated via the ANI timer, which happens
much later.
When a bandwidth change happens, it is appropriate to reset
the internal history data for the channel. Do this correctly in the
reset() routine by checking the "chanmode" variable.
Cc: stable@vger.kernel.org
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For AR9485 boards with XLNA, the default gpio config
is not set correctly, fix this.
Cc: stable@vger.kernel.org
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
N-PHY and HT-PHY support is more or less stable and should be activated
by default.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When b43 gets build into the kernel and it should use bcma we have to
ensure that bcma was also build into the kernel and not as a module.
In this patch this is also done for SSB, although you can not
build b43 without ssb support for now.
This fixes a build problem reported by Randy Dunlap in
5187EB95.2060605@infradead.org
Reported-By: Randy Dunlap <rdunlap@infradead.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All known ar7010+ar* device and current FW support STBC TX. This patch
make use of it and suggest to send STBC if peer support it.
I use wort "suggest" since currenly we have separate rate controller
in FW which will make decision based on rate and hardware.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
WMI PCP Start flow should not be handled through:
net_device_ops->ndo_open()->wil_up()->__wil_up()
because it missing mandatory FW parameters (SSID,Channel,IEs, Security...).
Prior to AP starting __wil_up() may be called with iftype set
cfg80211_ops->change_virtual_intf(NL80211_IFTYPE_AP or STATION)
depend on the application hostapd/wpa_supplicant/iw.
there should not be an attempt to start an AP flow,
AP/PCP start flow will be started latter by cfg80211_ops->start_ap().
Signed-off-by: Kirshenbaum Erez <erezk@wilocity.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tracing in wil6210 is activated with WIL6210_TRACING and not with
ATH6KL_TRACING, this is used for the ath6kl driver. Rename the config
option.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
at the vring initialisation, memory pool get allocated in the FW.
Make it 1-st because FW need this memory pool to precess
next commands
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No more need for special processing of EAPOL, FW can now send EAPOL frames
using normal Tx queue for TID 0
This fixes "schedule while atomic" bug - start_xmit called in softirq context;
while WMI mechanism that was used may sleep.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When starting secure AP, in some cases wpa_s provides probe template but not
probe/assoc IE's. In this case, derive missing IE's from probe.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Report FC from the frame itself, as auxiliary information includes
only frame subtype. This is preparation for future changes, when
DMG beacon (extension frame) may be reported through wmi_evt_rx_mgmt()
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
map card's back-door debug data
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It may take up to 3500ms for the FW to start AP/PCP. Increase accordingly,
adding some safety margin.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The CAB (Content after Beacon) queue is used for beacon-triggered
transmission of buffered multicast frames. If lots of multicast frames
were buffered and this queue fills up, it drowns out all regular
traffic. To limit the damage that buffered traffic can do, try to limit
the queued data to becaon_interval / 8.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds support for PS-Poll and U-APSD driver-buffered frames (part of
an aggregation session).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the UAPSD hardware queue to get PS-Poll responses out as fast as
possible and without backoff.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When initialization within brcmf_bus_start() fails on steps
before the brcmf_net_attach() the net_device for the primary
interface needs to be freed.
This patch resolves a panic during kernel boot as reported
by Stephen Warren.
ref.: http://mid.gmane.org/51AD1F22.2080004@wwwdotorg.org
Tested-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When data is available and fw signalling is enabled then TIM
information should be sent to firmware. If it can piggy back
on existing packet then do that otherwise create dummy packet
to get information out.
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In brcmf_net_attach() the hard_header_len is set to sum of ETH_HLEN
and the headroom needed by the bus interface. Better use increment
instead as hard_header_len is already initialized upon alloc_netdev().
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The BDC header contains PropTx TLV signals that are useful to capture
for debugging. This event captures the header and tlv's in binary
form. This can be post-processed using trace-cmd plugin.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
