The bus clock and function clock are separated at rk3399,
and others use one clock as the bus clock and function clock.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Enable the I2C core for this SoC.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
On Rockchip I2C the controller drops SDA low slightly too soon to meet
the "repeated start" requirements.
>From my own experimentation over a number of rates:
- controller appears to drop SDA at .875x (7/8) programmed clk high.
- controller appears to keep SCL high for 2x programmed clk high.
The first rule isn't enough to meet tSU;STA requirements in
Standard-mode on the system I tested on. The second rule is probably
enough to meet tHD;STA requirements in nearly all cases (especially
after accounting for the first), but it doesn't hurt to account for it
anyway just in case.
Even though the repeated start requirement only need to be accounted
for during a small part of the transfer, we'll adjust the timings for
the whole transfer to meet it. I believe that adjusting the timings
in just the right place to switch things up for repeated start would
require several extra interrupts and that doesn't seem terribly worth
it.
With this change and worst case rise/fall times, I see 100kHz i2c
going to ~85kHz. With slightly optimized rise/fall (800ns / 50ns) I
see i2c going to ~89kHz. Fast-mode isn't affected much because
tSU;STA is shorter relative to tHD;STA there.
As part of this change we needed to account for the SDA falling time.
The specification indicates that this should be the same, but we'll
follow Designware's lead and add a binding. Note that we deviate from
Designware and assign the default SDA falling time to be the same as
the SCL falling time, which is incredibly likely.
Signed-off-by: Doug Anderson <dianders@chromium.org>
[wsa: rebased to i2c/for-next]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The number of clock cycles to be written into the CLKDIV register
that determines the I2C clk high phase includes the rise time.
So to meet the timing requirements defined in the I2C specification
which defines the minimal time SCL has to be high, the rise time
has to taken into account. The same applies to the low phase with
falling time.
In my test on RK3288-Pink2 board, which is not an upstream board yet,
if external pull-up resistor is 4.7K, rise_ns is about 700ns.
So the measured high_ns is about 3900ns, which is less than 4000ns
(the minimum high_ns in I2C specification for Standard-mode).
To fix this bug min_low_ns should include fall time and min_high_ns
should include rise time.
This patch merged the patch from chromium project which can get the
rise and fall times for signals from the device tree. This allows us
to more accurately calculate timings. see:
https://chromium-review.googlesource.com/#/c/232774/
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
[wsa: fixed a typo in the docs]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Driver for the native I2C adapter found in Rockchip RK3xxx SoCs.
Configuration is only possible through devicetree. The driver is
interrupt driven and supports the I2C_M_IGNORE_NAK mangling bit.
Signed-off-by: Max Schwarz <max.schwarz@online.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
