The comment is wrong, glue is devm_kzalloc-ed mem attached to the
"allwinner,sun4i-a10-musb" compatible platform-dev. Where as
glue->musb_pdev is a newly created "musb-hdrc" platform-dev.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[b-liu@ti.com: revise subject prefix]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stop using the return value of platform_device_register_full() to get to
the struct musb in sunxi_musb_work(). If a gadget has been registered
(insmod-ed) before the musb driver, then musb_start will get called
from the musb_core probe function and sunxi_musb_work() may run before
platform_device_register_full() has returned.
Instead store a pointer to struct musb in struct sunxi_glue when
sunxi_musb_enable gets called. Note that sunxi_musb_enable always gets
called before sunxi_musb_work() can run.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[b-liu@ti.com: revise subject prefix]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the board is powering attached usb devices via the otg port
sometimes / on some devices it takes slightly too long for the Vbus
detection code in phy-sun4i-usb.c to signal that Vbus is high after
enabling Vbus and the musb hardware signals a MUSB_INTR_VBUSERROR
interrupt.
This commit sets the otg state to A_WAIT_VRISE upon enabling Vbus
making musb_stage0_irq() ignore the first VBUSERR_RETRY_COUNT
VBUSERROR interrupts, fixing connection issues in these cases.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[b-liu@ti.com: revise subject prefix]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the mode handling to the platform_set_mode callback.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[b-liu@ti.com: revise subject prefix]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MODULE_DEVICE_TABLE() is missing, so the module isn't auto-loading on
sunxi systems using the OTG controller. This commit adds the missing
line so it loads automatically when building it as a module and running
on a system with an USB OTG port.
Signed-off-by: Emilio López <emilio.lopez@collabora.co.uk>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Now that it is possible to build in multiple dma engines, we can no longer
require MUSB_PIO_ONLY to be set when using the sunxi musb glue.
This patch adds dummy dma hooks to make the musb glue work without
MUSB_PIO_ONLY. This hooks are fake because we do not support dma with
musb on sunxi. The Allwinnner Android kernels have some dma code, but it
is disabled as Allwinner never managed to get it to work.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
By using the unified device property interface, the function
can be made available for all platforms and not just the
ones using DT.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The A33 SoC uses the same musb controller as found on the A31 and later,
but allwinner has removed the configdata register, this commit adds special
handling for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The A31 SoC uses the same musb controller as found in earlier SoCs, but it
is hooked up slightly different. Its SRAM is private and no longer controlled
through the SRAM controller, and its reset is controlled via a separate
reset controller. This commit adds support for this setup.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is based on initial code to get the Allwinner sunxi musb controller
supported by Chen-Yu Tsai and Roman Byshko.
This adds support for the Allwinner sunxi musb controller in both host only
and otg mode. Peripheral only mode is not supported, as no boards use that.
This has been tested on a cubietruck (A20 SoC) and an UTOO P66 tablet
(A13 SoC) with a variety of devices in host mode and with the g_serial gadget
driver in peripheral mode, plugging otg / host cables in/out a lot of times
in all possible imaginable plug orders.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
