When a shared MSI vector must be used (e.g. when VTd is disabled on
x86_64), each event MSI vector must be set to the shared vector idx.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Hemant Kumar<hemantk@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The ring element data, though being part of coherent memory, still need
to be performed before updating the ring context to point to this new
element. That can be guaranteed with a memory barrier (dma_wmb).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
MHI hardware channels are usually the hardware accelerated data path
e.g. IP packets path for modems. This path needs to be optimized for
low latency and high throughput. After several tests on FN980m SDX55
based modem, it seems 1ms is a good default irq_moderation value:
- It allows to reach the maximum download throughput
- It introduces limited latency (5ms is too high)
- It prevents interrupt flooding
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Add support for Diag over MHI. Qualcomm Diag is the qualcomm
diagnostics interface that can be used to collect modem logs,
events, traces, etc. It can be used by tools such QPST or QXDM.
This patch adds the DIAG channels and a dedicated event ring.
Reviewed-by Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
On cold boot, device can take slightly more than 5 seconds to start.
Increase the timeout to prevent MHI power-up issues.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
If the modem crashes for any reason, we may not be able to detect
it at MHI level (MHI registers not reachable anymore).
This patch implements a health-check mechanism to check regularly
that device is alive (MHI layer can communicate with). If device
is not alive (because a crash or unexpected reset), the recovery
procedure is triggered.
Tested successfully with Telit FN980m module.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
In AER capable root complex, errors are reported to the host which
can then act accordingly and perform PCI recovering procedure.
This patch enables error reporting and implements error_detected,
slot_reset and resume callbacks.
Reviewed-by Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Add support for system wide suspend/resume. During suspend, MHI
device controller must be put in M3 state and PCI bus in D3 state.
Add a recovery procedure allowing to reinitialize the device in case
of error during resume steps, which can happen if device loses power
(and so its context) while system suspend.
Reviewed-by Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Add support for resetting the device, reset can be triggered in case
of error or manually via sysfs (/sys/bus/pci/devices/*/reset).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Hardware channels have a feature called burst mode that allows to
queue transfer ring element(s) (TRE) to a channel without ringing
the device doorbell. In that mode, the device is polling the channel
context for new elements. This reduces the frequency of host initiated
doorbells and increase throughput.
Create a new dedicated macro for hardware channels with burst enabled.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
If the IPA (IP hardware accelerator) is starved of event ring elements,
the modem is crashing (SDX55). That can be prevented by setting a
larger number of events (i.e 2 x number of channel ring elements).
Tested with FN980m module.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The MHI specification allows to perform a hard reset of the device
when writing to the SOC_RESET register. It can be used to completely
restart the device (e.g. in case of unrecoverable MHI error).
This is up to the MHI controller driver to determine when this hard
reset should be used, and in case of MHI errors, should be used as
a reset of last resort (after standard MHI stack reset).
This function is a stateless function, the MHI layer do nothing except
triggering the reset by writing into the right register(s), this is up
to the caller to ensure right mhi_controller state (e.g. unregister the
controller if necessary).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Here is the big char/misc driver update for 5.11-rc1.
Continuing the tradition of previous -rc1 pulls, there seems to be more
and more tiny driver subsystems flowing through this tree.
Lots of different things, all of which have been in linux-next for a
while with no reported issues:
- extcon driver updates
- habannalab driver updates
- mei driver updates
- uio driver updates
- binder fixes and features added
- soundwire driver updates
- mhi bus driver updates
- phy driver updates
- coresight driver updates
- fpga driver updates
- speakup driver updates
- slimbus driver updates
- various small char and misc driver updates
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX9iDZA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylRMACgqxKS2CUcY8tPnR5weHEsbz6O+KAAn3BtEFnK
7V9EnSuZe4L1jNOHOB5V
=xzHh
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc driver updates from Greg KH:
"Here is the big char/misc driver update for 5.11-rc1.
Continuing the tradition of previous -rc1 pulls, there seems to be
more and more tiny driver subsystems flowing through this tree.
Lots of different things, all of which have been in linux-next for a
while with no reported issues:
- extcon driver updates
- habannalab driver updates
- mei driver updates
- uio driver updates
- binder fixes and features added
- soundwire driver updates
- mhi bus driver updates
- phy driver updates
- coresight driver updates
- fpga driver updates
- speakup driver updates
- slimbus driver updates
- various small char and misc driver updates"
* tag 'char-misc-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (305 commits)
extcon: max77693: Fix modalias string
extcon: fsa9480: Support TI TSU6111 variant
extcon: fsa9480: Rewrite bindings in YAML and extend
dt-bindings: extcon: add binding for TUSB320
extcon: Add driver for TI TUSB320
slimbus: qcom: fix potential NULL dereference in qcom_slim_prg_slew()
siox: Make remove callback return void
siox: Use bus_type functions for probe, remove and shutdown
spmi: Add driver shutdown support
spmi: fix some coding style issues at the spmi core
spmi: get rid of a warning when built with W=1
uio: uio_hv_generic: use devm_kzalloc() for private data alloc
uio: uio_fsl_elbc_gpcm: use device-managed allocators
uio: uio_aec: use devm_kzalloc() for uio_info object
uio: uio_cif: use devm_kzalloc() for uio_info object
uio: uio_netx: use devm_kzalloc() for or uio_info object
uio: uio_mf624: use devm_kzalloc() for uio_info object
uio: uio_sercos3: use device-managed functions for simple allocs
uio: uio_dmem_genirq: finalize conversion of probe to devm_ handlers
uio: uio_dmem_genirq: convert simple allocations to device-managed
...
First set of patches for v5.11. rtw88 getting improvements to work
better with Bluetooth and other driver also getting some new features.
mhi-ath11k-immutable branch was pulled from mhi tree to avoid
conflicts with mhi tree.
Major changes:
rtw88
* major bluetooth co-existance improvements
wilc1000
* Wi-Fi Multimedia (WMM) support
ath11k
* Fast Initial Link Setup (FILS) discovery and unsolicited broadcast
probe response support
* qcom,ath11k-calibration-variant Device Tree setting
* cold boot calibration support
* new DFS region: JP
wnc36xx
* enable connection monitoring and keepalive in firmware
ath10k
* firmware IRAM recovery feature
mhi
* merge mhi-ath11k-immutable branch to make MHI API change go smoothly
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJfyTQyAAoJEG4XJFUm622bCdcIAIyVnqdW7pnoDmWIyQmAEnD9
vGARkzghPHXnufpOzohyDdxT12X9klhrxSVIgzEgH1/pl3i1PpnF6KXyGFCC44Lw
wrLXhQygPzmIW1IZtJJE3G72WExXoRjWx6LD1I7C7oEIduqFixXADmK2tKzFp795
Jxum+sOeT6+Dk1OvO/fIroBHX73mRE9zAuiTIMpt2G1j8uXs9QVfcTbTrUshLASN
0sX9J6JutltBuM4G7+bFpVzKnLnlQ7ebUaF6nvTCQsgHWZwkS7yAubSWX9sFohbR
UXgQHNE83s/esOg7nBxAfqTKP8mbxsobmxZtxE5GR5vFY5FJDxqP9Zc2KzPp39w=
=CbX/
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-12-03' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.11
First set of patches for v5.11. rtw88 getting improvements to work
better with Bluetooth and other driver also getting some new features.
mhi-ath11k-immutable branch was pulled from mhi tree to avoid
conflicts with mhi tree.
Major changes:
rtw88
* major bluetooth co-existance improvements
wilc1000
* Wi-Fi Multimedia (WMM) support
ath11k
* Fast Initial Link Setup (FILS) discovery and unsolicited broadcast
probe response support
* qcom,ath11k-calibration-variant Device Tree setting
* cold boot calibration support
* new DFS region: JP
wnc36xx
* enable connection monitoring and keepalive in firmware
ath10k
* firmware IRAM recovery feature
mhi
* merge mhi-ath11k-immutable branch to make MHI API change go smoothly
* tag 'wireless-drivers-next-2020-12-03' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next: (180 commits)
wl1251: remove trailing semicolon in macro definition
airo: remove trailing semicolon in macro definition
wilc1000: added queue support for WMM
wilc1000: call complete() for failure in wilc_wlan_txq_add_cfg_pkt()
wilc1000: free resource in wilc_wlan_txq_add_mgmt_pkt() for failure path
wilc1000: free resource in wilc_wlan_txq_add_net_pkt() for failure path
wilc1000: added 'ndo_set_mac_address' callback support
brcmfmac: expose firmware config files through modinfo
wlcore: Switch to using the new API kobj_to_dev()
rtw88: coex: add feature to enhance HID coexistence performance
rtw88: coex: upgrade coexistence A2DP mechanism
rtw88: coex: add action for coexistence in hardware initial
rtw88: coex: add function to avoid cck lock
rtw88: coex: change the coexistence mechanism for WLAN connected
rtw88: coex: change the coexistence mechanism for HID
rtw88: coex: update AFH information while in free-run mode
rtw88: coex: update the mechanism for A2DP + PAN
rtw88: coex: add debug message
rtw88: coex: run coexistence when WLAN entering/leaving LPS
Revert "rtl8xxxu: Add Buffalo WI-U3-866D to list of supported devices"
...
====================
Link: https://lore.kernel.org/r/20201203185732.9CFA5C433ED@smtp.codeaurora.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are a few problems with the error handling in this function. They
mostly center around the alloc_ordered_workqueue() allocation.
1) If that allocation fails or if the kcalloc() prior to it fails then
it leads to a NULL dereference when we call
destroy_workqueue(mhi_cntrl->hiprio_wq).
2) The error code is not set.
3) The "mhi_cntrl->mhi_cmd" allocation is not freed.
The error handling was slightly confusing and I re-ordered it to be in
the exact mirror/reverse order of how things were allocated. I changed
the label names to say what the goto does instead of describing where
the goto comes from.
Fixes: 8f70397876 ("bus: mhi: core: Move to using high priority workqueue")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
This patch fixes the hierarchical structure of MHI devices. Indeed,
MHI client devices are directly 'enumerated' from the mhi controller
and therefore must be direct descendants/children of their mhi
controller device, in accordance with the Linux Device Model.
Today both MHI clients and controller devices are at the same level,
this patch ensures that MHI controller is parent of its client devices.
The hierarchy is especially important for power management (safe
suspend/resume order). It is also useful for userspace to determine
relationship between MHI client devices and controllers.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Today the MHI controller name is simply cloned from the underlying
bus device (its parent), that gives the following device structure
for e.g. a MHI/PCI controller:
devices/pci0000:00/0000:00:01.2/0000:02:00.0/0000:02:00.0
devices/pci0000:00/0000:00:01.2/0000:02:00.0/0000:02:00.0/0000:02:00.0_IPCR
...
That's quite misleading/confusing and can cause device registering
issues because of duplicate dev name (e.g. if a PCI device register
two different MHI instances).
This patch changes MHI core to create indexed mhi controller names
(mhi0, mhi1...) in the same way as other busses (i2c0, usb0...).
The previous example becomes:
devices/pci0000:00/0000:00:01.2/0000:02:00.0/mhi0
devices/pci0000:00/0000:00:01.2/0000:02:00.0/mhi0/mhi0_IPCR
...
v2: move index field at the end of mhi_controller struct (before bool)
to avoid breaking well packed alignment.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
While powering down, the device may or may not acknowledge an MHI
RESET issued by host for a graceful shutdown scenario and end up
sending an incoming data packet after tasklets have been killed.
If a rogue device sends this interrupt for a data transfer event
ring update, it can result in a tasklet getting scheduled while a
clean up is ongoing or has completed and cause access to freed
memory leading to a NULL pointer exception. Remove the interrupt
handlers for MHI event rings early on to avoid this scenario.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
mhi_power_down() does not ensure that the PM state is moved to an
inaccessible state soon enough as the system can encounter
scheduling delays till mhi_pm_disable_transition() gets called.
Additionally, if an MHI controller decides that the device is now
inaccessible and issues a power down, the register inaccessible
state is not maintained by moving from MHI_PM_LD_ERR_FATAL_DETECT
to MHI_PM_SHUTDOWN_PROCESS. This can result in bus errors if a
client driver attempted to read registers when powering down.
Close these gaps and avoid any race conditions to prevent such
activity.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Currently, there exist a set of if...else statements in the
mhi_pm_disable_transition() function which make handling system
error and disable transitions differently complex. To make that
cleaner and facilitate differences in behavior, separate these
two transitions for MHI host.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Current design allows a controller to register with MHI successfully
without the need to have any IRQs available for use. If no IRQs are
available, power up requests to MHI can fail after a successful
registration with MHI. Improve the design by checking for the number
of IRQs available sooner within the mhi_regsiter_controller() API as
it is required to be specified by the controller.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
If the host receives a mission mode event and by the time it can get
to processing it, the register accesses fail implying a connectivity
error, MHI should move to an error state. This helps avoid longer wait
times from a synchronous power up perspective and accurately reflects
the MHI execution environment and power management states.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Correct the "error_read" label to say "error_ready_state" as that
is the appropriate usage of the label.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Move MHI to a firmware download error state for a failure to find
the firmware files or to load SBL or EBL image using BHI/BHIe. This
helps detect an error state sooner and shortens the wait for a
synchronous power up timeout.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
If an mhi_power_down() is initiated after the device has entered
RDDM and a status callback was provided for it, it is possible
that another BHI interrupt fires while waiting for the MHI
RESET to be cleared. If that happens, MHI host would have moved
a "disabled" execution environment and the check to allow sending
an RDDM status callback will pass when it is should not. Add a
check to see if MHI is in an active state before proceeding.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
In some cases, the entry of device to RDDM execution environment
can occur after a significant amount of time has elapsed and a
SYS_ERROR state change event has already arrived. This can result
in scenarios where MHI controller and client drivers are unaware
of the error state of the device. Remove the check for rddm_image
when processing the SYS_ERROR state change as it is present in
mhi_pm_sys_err_handler() already and prevent further activity
until the expected RDDM execution environment change occurs or
the controller driver decides further action.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
MHI client drivers can request a device wake even if the device
may be in an error state or undergoing a shutdown. To prevent
unnecessary device wake processing, check for the device state
and bail out early so that the clients are made aware of the
device state sooner.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
MHI work is currently scheduled on the global/system workqueue and can
encounter delays on a stressed system. To avoid those unforeseen
delays which can hamper bootup or shutdown times, use a dedicated high
priority workqueue instead of the global/system workqueue.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
mhi_fw_load_sbl() function is currently used to transfer SBL or EDL
images over BHI (Boot Host Interface). Same goes with mhi_fw_load_amss()
which uses BHIe. However, the contents of these functions do not
indicate support for a specific set of images. Since these can be used
for any image download over BHI or BHIe, rename them based on the
protocol used.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
If MHI is unable to determine the execution environment during
the panic path, host must skip the RDDM download. This can happen
if the BHI offset read or the BHI_EXECENV register read fails
indicating that the underlying transport is unresponsive. Hence,
there is no need to trigger an RDDM using SYSERR or request an
SOC reset.
Suggested-by: Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
mhi_download_rddm_img() uses a shorter version of the word image.
Expand it and rename the function to mhi_download_rddm_image().
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The mhi_fw_load_worker() function no longer exists. Remove its
declaration as part of code clean-up.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The mhi_get_exec_env() APIs can be used by the controller drivers
to query the execution environment of the MHI device. Expose it
so it can be used in some scenarios to determine behavior of
controllers.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
There is an extra 'i' counter in the mhi_firmware_copy() function
which is unused. Remove it to clean-up code and reduce stack
space as well as improve efficiency of the function.
Fixes: cd457afb16 ("bus: mhi: core: Add support for downloading firmware over BHIe")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Some MHI device drivers need to stop the channels in their driver
remove callback (e.g. module unloading), but the unprepare function
is aborted because MHI core moved the channels to suspended state
prior calling driver remove callback. This prevents the driver to
send a proper MHI RESET CHAN command to the device. Device is then
unaware of the stopped state of these channels.
This causes issue when driver tries to start the channels again (e.g.
module is reloaded), since device considers channels as already
started (inconsistent state).
Fix this by allowing channel reset when channel is suspended.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Functions parse_ev_cfg() and parse_ch_cfg() access mhi_cntrl->mhi_dev
before it is set in function mhi_register_controller(),
use cntrl_dev instead of mhi_dev.
Fixes: 0cbf260820 ("bus: mhi: core: Add support for registering MHI controllers")
Signed-off-by: Carl Yin <carl.yin@quectel.com>
Reviewed-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
This is a generic MHI-over-PCI controller driver for MHI only devices
such as QCOM modems. For now it supports registering of Qualcomm SDX55
based PCIe modules. The MHI channels have been extracted from mhi
downstream driver.
This driver is for MHI-only devices which have all functionalities
exposed through MHI channels and accessed by the corresponding MHI
device drivers (no out-of-band communication).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[mani: fixed up the Makefile rule]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The BHI_MSMHWID and BHI_OEMPKHASH macros take a value 'n' which is
a BHI register index. If 'n' is an expression rather than a simple
value, there can be an operator precedence issue which can result
in the incorrect calculation of the register offset. Adding
parentheses around the macro parameter can prevent such issues.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
There is double acquisition of the pm_lock from mhi_driver_remove()
function. Remove the read_lock_bh/read_unlock_bh calls for pm_lock
taken during a call to mhi_device_put() as the lock is acquired
within the function already. This will help avoid a potential
kernel panic.
Fixes: 189ff97cca ("bus: mhi: core: Add support for data transfer")
Reported-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
There is really no point having an auto-start for channels.
This is confusing for the device drivers, some have to enable the
channels, others don't have... and waste resources (e.g. pre allocated
buffers) that may never be used.
This is really up to the MHI device(channel) driver to manage the state
of its channels.
While at it, let's also remove the auto-start option from ath11k mhi
controller.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[mani: clubbed ath11k change]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
This function can be used by client driver to determine whether it's
possible to queue new elements in a channel ring.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/1604424234-24446-1-git-send-email-loic.poulain@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The Kbuild rule to build MHI should use the append operator. This fixes
the below warning reported by Kbuild test bot.
WARNING: modpost: missing MODULE_LICENSE() in
drivers/bus/mhi/core/main.o
WARNING: modpost: missing MODULE_LICENSE() in drivers/bus/mhi/core/pm.o
WARNING: modpost: missing MODULE_LICENSE() in
drivers/bus/mhi/core/boot.o
Fixes: 0cbf260820 ("bus: mhi: core: Add support for registering MHI controllers")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200929175218.8178-19-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no requirement for using a dedicated IRQ per event ring.
Some systems does not support multiple MSI vectors (e.g. intel
without CONFIG_IRQ_REMAP), In that case the MHI controller can
configure all the event rings to use the same interrupt (as fallback).
Allow this by removing the nr_irqs = ev_ring test and add extra check
in the irq_setup function.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200929175218.8178-17-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce sysfs entries to enable userspace clients the ability to read
the serial number and the OEM PK Hash values obtained from BHI. OEMs
need to read these device-specific hardware information values through
userspace for factory testing purposes and cannot be exposed via degbufs
as it may remain disabled for performance reasons. Also, update the
documentation for ABI to include these entries.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[mani: used dev_groups to manage sysfs attributes]
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200929175218.8178-16-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce debugfs entries to show state, register, channel, device,
and event rings information. Allow the host to dump registers,
issue device wake, and change the MHI timeout to help in debug.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200929175218.8178-15-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
