If a page is cached but its block was deallocated, we don't need to make
the page dirty again by gc and truncate_partial_data_page.
In that case, it needs to check its block allocation all the time instead
of giving up-to-date page.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
If page's on-disk block was deallocated, let's remove up-to-date flag to avoid
further access with wrong contents.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
cp_pack_start_sum is calculated in do_checkpoint and is equal to
cpu_to_le32(1 + cp_payload_blks + orphan_blocks). The number of
orphan inode blocks is take advantage of by recover_orphan_inodes
to readahead meta pages and recovery inodes. However, current codes
forget to reduce the number of cp payload blocks when calculate
the number of orphan inode blocks. This patch fix it.
Signed-off-by: Wanpeng Li <wanpeng.li@linux.intel.com>
Reviewed-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch introduces a generic ioctl for fs shutdown, which was used by xfs.
If this shutdown is triggered, filesystem stops any further IOs according to the
following options.
1. FS_GOING_DOWN_FULLSYNC
: this will flush all the data and dentry blocks, and do checkpoint before
shutdown.
2. FS_GOING_DOWN_METASYNC
: this will do checkpoint before shutdown.
3. FS_GOING_DOWN_NOSYNC
: this will trigger shutdown as is.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Some board designers, when running out of clock output pads, decide to
(mis)use PWM output pads to provide a clock to external components.
This driver supports this practice by providing an adapter between the
PWM and clock bindings in the device tree. As the PWM bindings specify
the period in the device tree, this is a fixed clock.
Tested-by: Janusz Uzycki <j.uzycki@elproma.com.pl>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Near the end of close_ctree, we're calling btrfs_free_block_rsv
to free up the orphan rsv. The problem is this call updates the
space_info, which has already been freed.
This adds a new __ function that directly calls kfree instead of trying
to update the space infos.
Signed-off-by: Chris Mason <clm@fb.com>
We loop through all of the dirty block groups during commit and write
the free space cache. In order to make sure the cache is currect, we do
this while no other writers are allowed in the commit.
If a large number of block groups are dirty, this can introduce long
stalls during the final stages of the commit, which can block new procs
trying to change the filesystem.
This commit changes the block group cache writeout to take appropriate
locks and allow it to run earlier in the commit. We'll still have to
redo some of the block groups, but it means we can get most of the work
out of the way without blocking the entire FS.
Signed-off-by: Chris Mason <clm@fb.com>
In order to create the free space cache concurrently with FS modifications,
we need to take a few block group locks.
The cache code also does kmap, which would schedule with the locks held.
Instead of going through kmap_atomic, lets just use lowmem for the cache
pages.
Signed-off-by: Chris Mason <clm@fb.com>
Block group cache writeout is currently waiting on the pages for each
block group cache before moving on to writing the next one. This commit
switches things around to send down all the caches and then wait on them
in batches.
The end result is much faster, since we're keeping the disk pipeline
full.
Signed-off-by: Chris Mason <clm@fb.com>
We'll need to put the io_ctl into the block_group cache struct, so
name it struct btrfs_io_ctl and move it into ctree.h
Signed-off-by: Chris Mason <clm@fb.com>
btrfs_evict_inode() needs to be more careful about stealing from the
global_rsv. We dont' want to end up aborting commit with ENOSPC just
because the evict_inode code was too greedy.
Signed-off-by: Chris Mason <clm@fb.com>
We're triggering a huge number of commits from
btrfs_async_reclaim_metadata_space. These aren't really requried,
because everyone calling the async reclaim code is going to end up
triggering a commit on their own.
Signed-off-by: Chris Mason <clm@fb.com>
When truncate starts, it allocates some space in the block reserves so
that we'll have enough to update metadata along the way.
For very large files, we can easily go through all of that space as we
loop through the extents. This changes truncate to refill the space
reservation as it progresses through the file.
Signed-off-by: Chris Mason <clm@fb.com>
As we delete large extents, we end up doing huge amounts of COW in order
to delete the corresponding crcs. This adds accounting so that we keep
track of that space and flushing of delayed refs so that we don't build
up too much delayed crc work.
This helps limit the delayed work that must be done at commit time and
tries to avoid ENOSPC aborts because the crcs eat all the global
reserves.
Signed-off-by: Chris Mason <clm@fb.com>
When we are deleting large files with large extents, we are building up
a huge set of delayed refs for processing. Truncate isn't checking
often enough to see if we need to back off and process those, or let
a commit proceed.
The end result is long stalls after the rm, and very long commit times.
During the commits, other processes back up waiting to start new
transactions and we get into trouble.
Signed-off-by: Chris Mason <clm@fb.com>
The CRG11 clock controller is managed by remote f/w.
This driver simply maps Linux CLK ops onto mailbox api.
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Vincent Yang <vincent.yang@socionext.com>
Signed-off-by: Tetsuya Nuriya <nuriya.tetsuya@socionext.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
The pxa3xx scheduler relies on the pxa-timer, which requires a clock for
its rate. As the clock handling will be taken over by the clock
framework, add this missing clock.
The miss was discovered by attempting to run a zylonite platform in a
device-tree configuration, with the future patch to shift clocks
handling to clock framework applied.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
HID Sensor Spec defines two usage ids for custom sensors
HID_USAGE_SENSOR_TYPE_OTHER_CUSTOM (0x09, 0xE1)
HID_USAGE_SENSOR_TYPE_OTHER_GENERIC(0x09, 0xE2)
In addition the standard also defines usage ids for custom fields.
The purpose of these sensors is to extend the functionality or provide a way to
obfuscate the data being communicated by a sensor. Without knowing the mapping
between the data and its encapsulated form, it is difficult for an driver to
determine what data is being communicated by the sensor. This allows some
differentiating use cases, where vendor can provide applications. Since these
can't be represented by standard sensor interfaces like IIO, we present these
as fields with
- type (input/output)
- units
- min/max
- get/set value
In addition an dev interface to transfer report events. Details about this
interface is described in /Documentation/hid/hid-sensor.txt. Manufacturers
should not use these ids for any standard sensors, otherwise the the
product/vendor id can be added to black list.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Reviewed-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-04-10
This series contains updates to ixgbe and documentation for igb,
ixgbe and ixgb.
Stephen cleans up documentation to igb, ixgbe and ixgb.
Don updates how bridge mode is stored to minimize obfuscation and
makes updates for future silicon easier. Adds a new bridge mode
support function which gathers all the logic needed to configure
bridge modes. Adds Source Address Prunning for VEPA bridge mode
for x550 devices.
Vasu adds specific FCoE offloads for x550 for DDP context programming
and increased DDP exchanges.
Alex Duyck cleans up the use of HW_VLAN_CTAG_FILTER in hw_features,
where the driver was actually ignoring the value of the bit and was
just assuming it was always set. Also cleans up the use of rcu_barrier()
since the driver has not used call_rcu() to free the rings for some
time now.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a oops due to a double list add when adding a reject PDU for
iscsit_allocate_iovecs allocation failures. The cmd has already been
added to the conn_cmd_list in iscsit_setup_scsi_cmd, so this has us call
iscsit_reject_cmd.
Note that for ERL0 the reject PDU is not actually sent, so this patch
is not completely tested. Just verified we do not oops. The problem is the
add reject functions return -1 which is returned all the way up to
iscsi_target_rx_thread which for ERL0 will drop the connection.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In cases of short transfer times the CPU is spending lots of time
in the interrupt handler and scheduler to reschedule the worker thread.
Measurements show that we have times where it takes 29.32us to between
the last clock change and the time that the worker-thread is running again
returning from wait_for_completion_timeout().
During this time the interrupt-handler is running calling complete()
and then also the scheduler is rescheduling the worker thread.
This time can vary depending on how much of the code is still in
CPU-caches, when there is a burst of spi transfers the subsequent delays
are in the order of 25us, so the value of 30us seems reasonable.
With polling the whole transfer of 4 bytes at 10MHz finishes after 6.16us
(CS down to up) with the real transfer (clock running) taking 3.56us.
So the efficiency has much improved and is also freeing CPU cycles,
reducing interrupts and context switches.
Because of the above 30us seems to be a reasonable limit for polling.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Transforms the bcm-2835 native SPI-chip select to their gpio-cs equivalent.
This allows for some support of some optimizations that are not
possible due to HW-gliches on the CS line - especially filling
the FIFO before enabling SPI interrupts (by writing to CS register)
while the transfer is already in progress (See commit: e3a2be3030)
This patch also works arround some issues in bcm2835-pinctrl which does not
set the value when setting the GPIO as output - it just sets up output and
(typically) leaves the GPIO as low. When a fix for this is merged then this
gpio_set_value can get removed from bcm2835_spi_setup.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Here are fixes gathered for 4.0-final; one FireFire endian fix, two
USB-audio quirks, and three HD-audio quirks.
All relatively small and device-specific fixes, should be pretty safe
to apply.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=hSdz
-----END PGP SIGNATURE-----
Merge tag 'sound-4.0' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here are fixes gathered for 4.0-final; one FireFire endian fix, two
USB-audio quirks, and three HD-audio quirks.
All relatively small and device-specific fixes, should be pretty safe
to apply"
* tag 'sound-4.0' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: usb - Creative USB X-Fi Pro SB1095 volume knob support
ALSA: hda - Fix headphone pin config for Lifebook T731
ALSA: bebob: fix to processing in big-endian machine for sending cue
ALSA: hda/realtek - Make more stable to get pin sense for ALC283
ALSA: usb-audio: don't try to get Benchmark DAC1 sample rate
ALSA: hda/realtek - Support Dell headset mode for ALC256
Use the generic IPC/mailbox APIs to replace the original processing
code for Broadwell platform.
Signed-off-by: Jin Yao <yao.jin@linux.intel.com>
Acked-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the generic IPC/mailbox APIs to replace the original processing
code for Baytrail platform.
Signed-off-by: Jin Yao <yao.jin@linux.intel.com>
Acked-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently in Intel SST driver, some similar IPC/mailbox processing
code are used in different platforms (e.g. in baytrail/broadwell).
This patch extracts the common code and creates new files
(sst-ipc.c/sst-ipc.h) to contain the common code and provide the generic
APIs for IPC/mailbox processing.
Signed-off-by: Jin Yao <yao.jin@linux.intel.com>
Acked-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To keep consistency with the other Kconfig entries, use the audio
interface acronyms (SSI and SPDIF) in the Kconfig menu text.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is not necessary to have regulator init data for a regulator. This
patch removes the necessity of this data and handles a NULL pointer
properly.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add an I2C bus driver i2c-xlp9xx.c to support the I2C block in the
XLP9xx/XLP5xx MIPS SoC. Update Kconfig and Makefile to add the
CONFIG_I2C_XLP9XX option.
Signed-off-by: Subhendu Sekhar Behera <sbehera@broadcom.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add vendor name "netlogic" in vendor-prefixes.txt, which will be used for
the Netlogic XLP and XLPII MIPS SoCs. These processors were from NetLogic
Microsystems that is now a part of Broadcom Corporation.
Signed-off-by: Subhendu Sekhar Behera <sbehera@broadcom.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Having a board where the I2C bus locks up occasionally made it clear
that the bus recovery in the i2c-davinci driver will only work on
some boards, because on regular boards, this will only toggle GPIO
lines that aren't muxed to the actual pins.
The I2C controller on SoCs like da850 (and da830), Keystone 2 has the
built-in capability to bit-bang its lines by using the ICPFUNC registers
of the i2c controller.
Implement the suggested procedure by toggling SCL and checking SDA using
the ICPFUNC registers of the I2C controller when present. Allow platforms
to indicate the presence of the ICPFUNC registers with a has_pfunc platform
data flag and add optional DT property "ti,has-pfunc" to indicate
the same in DT.
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Tested-by: Michael Lawnick <michael.lawnick@nokia.com>
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Mike Looijmans <milo-software@users.sourceforge.net>
[grygorii.strashko@ti.com: combined patches from Ben Gardiner and
Mike Looijmans and reimplemented ICPFUNC bus recovery using I2C
bus recovery infrastructure]
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch converts Davinci I2C driver to use I2C bus recovery
infrastructure, introduced by commit 5f9296ba21 ("i2c: Add
bus recovery infrastructure").
The i2c_bus_recovery_info is configured for Davinci I2C adapter
only in case scl_pin is provided in platform data.
As the controller must be held in reset while doing so, the
recovery routine must re-init the controller. Since this was already
being done after each call to i2c_recover_bus, move those calls into
the recovery_prepare/unprepare routines and as well.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch changes type of input parameter for
prepare/unprepare_recovery() callbacks from struct i2c_bus_recovery_info
* to struct i2c_adapter *. This allows to simplify implementation of
these callbacks and avoid type conversations from i2c_bus_recovery_info
to i2c_adapter. The i2c_bus_recovery_info can be simply retrieved from
struct i2c_adapter which contains pointer on it. There are no users
currently, so this is safe to do.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Some implementation of UFS host controller HW might have some non-standard
behaviours (quirks) when compared to behaviour specified by UFSHCI
specification. This patch add support to allow specifying all such quirks
to standard UFS host controller driver so standard driver takes them into
account.
In this change a UFSHCD_QUIRK_DELAY_BEFORE_DME_CMDS is introduced,
where a minimum delay of 1ms is required before DME commands for
stability purposes.
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: Gilad Broner <gbroner@codeaurora.org>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Sometimes, specific information about the UFS controller revision is
required in order to determine certain operations or execute
controller dependent quirks.
In order to avoid reading the controller revision multiple times,
we simply read it once and save this information in internal structure.
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: Gilad Broner <gbroner@codeaurora.org>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
For FA-WWPN is enabled port, if NPIV created on that port and,
if port link is brought down, then WWPN was restored from flash for both
physical and NPIV port. This will result in NPIV port and physical port
sharing same WWPN. Any application refreshing ports information will
not be able to scan NPIV port because of this behavior. So while restoring WWPN,
only restore physical port WWPN.
Signed-off-by: Sawan Chandak <sawan.chandak@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
On some vendor switches, when switch port is toggled (down /up),
then in some condition driver tries to configure virtual port,
before FW is actually in ready state to process any commands on wire.
At this time, configuring virtual port can fail. Add fix in driver
to make driver wait, for FW to be ready state before
Signed-off-by: Sawan Chandak <sawan.chandak@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
For ISP27XX, driver will capture new firmware dump even if there is
one already collected. Prevent this from happening by checking
fw_dumped flag.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
