The mechanism for specifying that the trf7970a
being used by the driver has the "IRQ Status Read"
erratum has been changed to a device tree property
('irq-status-read-quirk').
Document the new device tree property.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The trf7970a driver recently had support for the
'vin-voltage-override' property added to it. This
property is used to override the value given by
the regulator subsystem for the VIN pin's voltage.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The PTP reference clock, used for setting the addend in the Timestamp Addend
Register, was erroneously hard-coded (as reported in the databook just as
example).
The patch removes the macro named: STMMAC_SYSCLOCK and allows to use a
reference clock (clk_ptp_ref_i) that can be passed from the platform.
If not passed, the main driver clock will be used as default; note that
this can be fine on some platforms.
Note that, prior this patch, using the old STMMAC_SYSCLOCK on some platforms,
as side effect, the ptp clock can move faster/slower than the system clock.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the binding documentation for the Broadcom Starfighter 2 integrated
switch hardware.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add documentation for a bunch of new optional properties described in
ethernet.txt and fixed-link.txt, this includes: 'phy-handle', 'phy-mode'
and the 'fixed-link' subnode.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a generic UniMAC MDIO bus driver and its Device Tree binding, which
can be used by the BCMGENET driver as-is, and the upcoming Starfighter 2
Ethernet switch MDIO bus controller.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlP0oIQACgkQjTAFq1RaXHNvqgCghQt8v7M+WJR0oTGHoDh3wFGj
QF8AoIsZrElCuS2rLvgCobugiAOwXip2
=J1Qd
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-3.18-20140820' of git://gitorious.org/linux-can/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2014-08-20
this is a pull request of 10 patches for net-next/master.
There is one patch by Wolfram Sang to clean up the build system.
Two patches by Stefan Agner that add vf610 support to the flexcan
driver. Dong Aisheng add support for bosch's m_can core, which is found
in the new freescale ARM SoCs. Sergei Shtylyov improves the rcar_can
driver by supporting all input clocks and adding device tree support.
The next patch is a small cleanup for the bit rate calculation function
by Lad, Prabhakar. And finally a patch by Himangi Saraogi, which
converts the mcp251x driver to use dmam_alloc_coherent.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds fix_mac_speed() support for
Altera socfpga Ethernet controller. Emac splitter is a
soft IP core in FPGA system that converts GMII interface from
Synopsys mac to RGMII/SGMII interface. This splitter core is
an optional IP if user would like to use RGMII/SGMII
interface in their system. Software needs to update a register
in splitter core when there is speed change.
Signed-off-by: Ley Foon Tan <lftan@altera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Document the R-Car CAN device tree bindings.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This adds support for specifying the phy to be used with the fec in the
devicetree using the standard phy-handle property and also supports
fixed-link.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds documentation for APM X-Gene SoC ethernet DTS binding.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Ravi Patel <rapatel@apm.com>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/6lowpan/iphc.c
Minor conflicts in iphc.c were changes overlapping with some
style cleanups.
John W. Linville says:
====================
Please pull this last(?) batch of wireless change intended for the
3.17 stream...
For the NFC bits, Samuel says:
"This is a rather quiet one, we have:
- A new driver from ST Microelectronics for their NCI ST21NFCB,
including device tree support.
- p2p support for the ST21NFCA driver
- A few fixes an enhancements for the NFC digital laye"
For the Atheros bits, Kalle says:
"Michal and Janusz did some important RX aggregation fixes, basically we
were missing RX reordering altogether. The 10.1 firmware doesn't support
Ad-Hoc mode and Michal fixed ath10k so that it doesn't advertise Ad-Hoc
support with that firmware. Also he implemented a workaround for a KVM
issue."
For the Bluetooth bits, Gustavo and Johan say:
"To quote Gustavo from his previous request:
'Some last minute fixes for -next. We have a fix for a use after free in
RFCOMM, another fix to an issue with ADV_DIRECT_IND and one for ADV_IND with
auto-connection handling. Last, we added support for reading the codec and
MWS setting for controllers that support these features.'
Additionally there are fixes to LE scanning, an update to conform to the 4.1
core specification as well as fixes for tracking the page scan state. All
of these fixes are important for 3.17."
And,
"We've got:
- 6lowpan fixes/cleanups
- A couple crash fixes, one for the Marvell HCI driver and another in LE SMP.
- Fix for an incorrect connected state check
- Fix for the bondable requirement during pairing (an issue which had
crept in because of using "pairable" when in fact the actual meaning
was "bondable" (these have different meanings in Bluetooth)"
Along with those are some late-breaking hardware support patches in
brcmfmac and b43 as well as a stray ath9k patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This change adds bindings for the number of multicast hash bins and perfect
filter entries supported by the Synopsys EMAC. The Synopsys EMAC core is
configurable at device creation time, and can be configured for a different
number of multicast hash bins and a different number of perfect filter
entries. The device does not provide a way to query these parameters,
therefore parameters are required. The Altera Cyclone V SOC has support for
256 multicast hash bins and 128 perfect filter entries, and is different
than what's currently provided in the stmmac driver.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the amd-xgbe driver and phylib driver to better support
the 2.5GbE mode for the hardware. In order to be able establish
2.5GbE using clause 73 auto negotiation the device will support
speed sets of 1GbE/10GbE and 2.5GbE/10GbE.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for Tx and Rx hardware timestamping.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An earlier patch added support for the "dma-coherent" device property.
This patch adds this optional property to the amd-xgbe device bindings
documentation.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Broadcom bcm43xx sdio devices are fullmac devices that may be
integrated in ARM platforms. Currently, the brcmfmac driver for
these devices support use of platform data. This patch specifies
the bindings that allow this platform data to be expressed in the
devicetree.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
[hdegoede@redhat.com: drop clk / reg_on gpio handling, as there is no consensus
on how to handle this yet]
[hdegoede@redhat.com: move from bindings/staging to bindings]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The similar MDIO HW blocks is used by keystone 2 SoCs as
in Davinci SoCs:
- one in Gigabit Ethernet (GbE) Switch Subsystem
See http://www.ti.com/lit/ug/sprugv9d/sprugv9d.pdf
- one in 10 Gigabit Ethernet Subsystem
See http://www.ti.com/lit/ug/spruhj5/spruhj5.pdf
Hence, reuse Davinci MDIO driver for Keystone 2 and
enable TI networking for Keystone 2 devices
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds a new network driver for the network controller in Marvell
Armada 375 SoC.
Given the controller is very different from the ones in the other Marvell
SoCs that use the mv643xx_eth (Kirkwood, Orion, Discovery) and mvneta
(Armada 370/38x/XP) drivers, a new driver is needed.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
[Ezequiel: coding style cleanup]
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for Wake-on-LAN using Magic Packet with or without SecureOn
password is implemented doing the following:
- setting the password to the relevant UniMAC registers
- flagging the device as a wakeup source for the system, as well as
its Wake-on-LAN interrupt
- prepare the hardware for entering WoL mode
- enabling the MPD interrupt to wake us
The Device Tree binding documentation is also reflected to specify the
third optional Wake-on-LAN interrupt line.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides the documentation of the device bindings
for the AMD 10GbE platform driver.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
Please pull this batch of updates intended for 3.16...
For the mac80211 bits, Johannes says:
"Here I just have Heikki's rfkill GPIO cleanups.
The ARM/tegra patch is OK with the maintainer (Stephen). Let me know of
any problems."
and;
"We have a whole bunch of work on CSA by Andrei, Luca and Michal, but
unfortunately it doesn't seem quite complete yet so it's still disabled.
There's some TDLS work from Arik, and the rest is mostly minor fixes and
cleanups."
For the NFC bits, Samuel says:
"This is the NFC pull request for 3.16. We have:
- STMicroeectronics st21nfca support. The st21nfca is an HCI chipset and
thus relies on the HCI stack. This submission provides support for tag
redaer/writer mode (including Type 5) and device tree bindings.
- PM runtime support and a bunch of bug fixes for TI's trf7970a.
- Device tree support for NXP's pn544. Legacy platform data support is
obviously kept intact.
- NFC Tag type 4B support to the NFC Digital stack.
- SOCK_RAW type support to the raw NFC socket, and allow NCI
sniffing from that. This can be extended to report HCI frames and also
proprietarry ones like e.g. the pn533 ones."
For the iwlwifi bits, Emmanuel says:
"Eran continues to work on new devices, Eyal is still digging in
the rate control stuff, and Johannes added new functionality to the
debug system we have in place now along with a few cleanups he made
on the way. That's pretty much it."
and;
"Avri continues to work on the power code and Eran is improving the
NVM handling as a preparations for new devices on which he works
with Liad. Luca cleans up a bit the code while working on CSA. I have
the regular BT Coex stuff and a small lockdep fix. Johannes has his
regular amount of clean ups and improvements, the main one is the
ability to leave 2 chains open to improve diversity and hence the
throughput in high attenuation scenarios."
and;
"The regular amount of housekeeping here. I merged iwlwifi-fixes.git to
be able to add the patch you didn't want in wireless.git at that stage
of the -rc cycle. Luca has a few preparations for CSA implementation
and also what seems to be a bugfix for P2P but hasn't caused issues
we could notice."
For the Atheros bits, Kalle says:
"For ath10k Michal did various small fixes on how we handle
hardware/firmware problems and he also fixed two memory leaks."
Also included are a couple of pulls from the wireless tree to
avoid/resolve merge issues...
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Replaced st,st21nfca-i2c by st,st21nfca_i2c to be concistent
with below configuration and driver in drivers/nfc/st21nfca/
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The ks8851 SPI ethernet wasn't documented, but we documented the
optional regulator supply for it under the mll based ethernet
chip. Furthermore, that compatible string needed another 'l'. Fix
all of this and document the optional vdd-io and reset-gpios
properties.
Cc: Nishanth Menon <nm@ti.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the Freescale TSEC PHY, Broadcom GENET & SYSTEMPORT Device Tree
binding documentation to refer to the fixed-link Device Tree binding in
fixed-link.txt.
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the fixed-link Device Tree binding documentation to contain
information about the old and deprecated 5-digit 'fixed-link' property.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the NFC pull request for 3.16. We have:
- STMicroeectronics st21nfca support. The st21nfca is an HCI chipset and
thus relies on the HCI stack. This submission provides support for tag
redaer/writer mode (including Type 5) and device tree bindings.
- PM runtime support and a bunch of bug fixes for TI's trf7970a.
- Device tree support for NXP's pn544. Legacy platform data support is
obviously kept intact.
- NFC Tag type 4B support to the NFC Digital stack.
- SOCK_RAW type support to the raw NFC socket, and allow NCI
sniffing from that. This can be extended to report HCI frames and also
proprietarry ones like e.g. the pn533 ones.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=cSl+
-----END PGP SIGNATURE-----
Merge tag 'nfc-next-3.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-next
Samuel Ortiz <sameo@linux.intel.com> says:
"NFC: 3.16: First pull request
This is the NFC pull request for 3.16. We have:
- STMicroeectronics st21nfca support. The st21nfca is an HCI chipset and
thus relies on the HCI stack. This submission provides support for tag
redaer/writer mode (including Type 5) and device tree bindings.
- PM runtime support and a bunch of bug fixes for TI's trf7970a.
- Device tree support for NXP's pn544. Legacy platform data support is
obviously kept intact.
- NFC Tag type 4B support to the NFC Digital stack.
- SOCK_RAW type support to the raw NFC socket, and allow NCI
sniffing from that. This can be extended to report HCI frames and also
proprietarry ones like e.g. the pn533 ones."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Describe the properties used by the st21nfca NFC controller driver.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Some Ethernet MACs have a "fixed link", and are not connected to a
normal MDIO-managed PHY device. For those situations, a Device Tree
binding allows to describe a "fixed link" using a special PHY node.
This patch adds:
* A documentation for the fixed PHY Device Tree binding.
* An of_phy_is_fixed_link() function that an Ethernet driver can call
on its PHY phandle to find out whether it's a fixed link PHY or
not. It should typically be used to know if
of_phy_register_fixed_link() should be called.
* An of_phy_register_fixed_link() function that instantiates the
fixed PHY into the PHY subsystem, so that when the driver calls
of_phy_connect(), the PHY device associated to the OF node will be
found.
These two additional functions also support the old fixed-link Device
Tree binding used on PowerPC platforms, so that ultimately, the
network device drivers for those platforms could be converted to use
of_phy_is_fixed_link() and of_phy_register_fixed_link() instead of
of_phy_connect_fixed_link(), while keeping compatibility with their
respective Device Tree bindings.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
AM43xx phy mode selection is similar to AM33xx platform, so adding only
the compatibility string to the driver
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add dra7xx support for selecting the phy mode which is present in control
module of dra7xx SoC
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/altera/altera_sgdma.c
net/netlink/af_netlink.c
net/sched/cls_api.c
net/sched/sch_api.c
The netlink conflict dealt with moving to netlink_capable() and
netlink_ns_capable() in the 'net' tree vs. supporting 'tc' operations
in non-init namespaces. These were simple transformations from
netlink_capable to netlink_ns_capable.
The Altera driver conflict was simply code removal overlapping some
void pointer cast cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix aliases syntax in device-tree binding example to avoid
copy-paste errors (the alias would be dropped silently).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Renames micrel-ksz9021.txt to micrel-ksz90x1.txt and adds documentation for
the KSZ9031 binding from patch 1. Also adds step increment information, and
note about phy fixups.
Signed-off-by: Hubert Chaumette <hchaumette@adeneo-embedded.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) e1000e computes header length incorrectly wrt vlans, fix from Vlad
Yasevich.
2) ns_capable() check in sock_diag netlink code, from Andrew
Lutomirski.
3) Fix invalid queue pairs handling in virtio_net, from Amos Kong.
4) Checksum offloading busted in sxgbe driver due to incorrect
descriptor layout, fix from Byungho An.
5) Fix build failure with SMC_DEBUG set to 2 or larger, from Zi Shen
Lim.
6) Fix uninitialized A and X registers in BPF interpreter, from Alexei
Starovoitov.
7) Fix arch dependencies of candence driver.
8) Fix netlink capabilities checking tree-wide, from Eric W Biederman.
9) Don't dump IFLA_VF_PORTS if netlink request didn't ask for it in
IFLA_EXT_MASK, from David Gibson.
10) IPV6 FIB dump restart doesn't handle table changes that happen
meanwhile, causing the code to loop forever or emit dups, fix from
Kumar Sandararajan.
11) Memory leak on VF removal in bnx2x, from Yuval Mintz.
12) Bug fixes for new Altera TSE driver from Vince Bridgers.
13) Fix route lookup key in SCTP, from Xugeng Zhang.
14) Use BH blocking spinlocks in SLIP, as per a similar fix to CAN/SLCAN
driver. From Oliver Hartkopp.
15) TCP doesn't bump retransmit counters in some code paths, fix from
Eric Dumazet.
16) Clamp delayed_ack in tcp_cubic to prevent theoretical divides by
zero. Fix from Liu Yu.
17) Fix locking imbalance in error paths of HHF packet scheduler, from
John Fastabend.
18) Properly reference the transport module when vsock_core_init() runs,
from Andy King.
19) Fix buffer overflow in cdc_ncm driver, from Bjørn Mork.
20) IP_ECN_decapsulate() doesn't see a correct SKB network header in
ip_tunnel_rcv(), fix from Ying Cai.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (132 commits)
net: macb: Fix race between HW and driver
net: macb: Remove 'unlikely' optimization
net: macb: Re-enable RX interrupt only when RX is done
net: macb: Clear interrupt flags
net: macb: Pass same size to DMA_UNMAP as used for DMA_MAP
ip_tunnel: Set network header properly for IP_ECN_decapsulate()
e1000e: Restrict MDIO Slow Mode workaround to relevant parts
e1000e: Fix issue with link flap on 82579
e1000e: Expand workaround for 10Mb HD throughput bug
e1000e: Workaround for dropped packets in Gig/100 speeds on 82579
net/mlx4_core: Don't issue PCIe speed/width checks for VFs
net/mlx4_core: Load the Eth driver first
net/mlx4_core: Fix slave id computation for single port VF
net/mlx4_core: Adjust port number in qp_attach wrapper when detaching
net: cdc_ncm: fix buffer overflow
Altera TSE: ALTERA_TSE should depend on HAS_DMA
vsock: Make transport the proto owner
net: sched: lock imbalance in hhf qdisc
net: mvmdio: Check for a valid interrupt instead of an error
net phy: Check for aneg completion before setting state to PHY_RUNNING
...
This adds ability for the arc_emac to really handle its supplying clock.
To get the needed clock-frequency either a real clock or the previous
clock-frequency property must be provided.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Max Schwarz <max.schwarz@online.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the Device Tree bindings documentation for the Broadcom SYSTEMPORT
Ethernet MAC controller hardware.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds devicetree bindings for the at86rf230 IEEE 802.15.4 SPI
device driver.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This should make the driver usable with VIA/WonderMedia ARM-based
Systems-on-Chip integrated Rhine III adapters. Note that these
are always in MMIO mode, and don't have any known EEPROM.
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
s/interrupts-names/interrupt-names/g
s/clocks-names/clock-names/g
Some of the binding files and device tree files get this wrong and the
kernel won't be able to pick it up. Fix them up now so that they don't
get widely used.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by : Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
The trf7970a driver recently had support added for the 'autosuspend-delay'
property so document it.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Describe the properties used by the PN544 NFC controller driver.
Signed-off-by: Clément Perrochaud <clement.perrochaud@nxp.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This commit adds the necessary definitions for the PHY layer to
recognize "qsgmii" as a valid PHY interface. A QSMII interface, as
defined at
http://en.wikipedia.org/wiki/Media_Independent_Interface#Quad_Serial_Gigabit_Media_Independent_Interface,
is "is a method of combining four SGMII lines into a 5Gbit/s
interface. QSGMII, like SGMII, uses LVDS signalling for the TX and RX
data and a single LVDS clock signal. QSGMII uses significantly fewer
signal lines than four SGMII busses."
This type of MAC <-> PHY connection might require special handling on
the MAC driver side, so it should be possible to express this type of
MAC <-> PHY connection, for example in the Device Tree.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: devicetree@vger.kernel.org
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A large part of the arm-soc patches are nowadays DT changes, adding support
for new SoCs, boards and devices without changing kernel source. The plan
is still to move the devicetree files out of the kernel tree and reduce
the amount of churn going on here, but we keep finding reasons to delay
doing that.
Changes are really all over the place, with little sticking out particularly.
We have contributions from a total of 116 people in this branch.
Unfortunately, the size of this branch also causes a significant number
of conflicts at the moment, typically when subsystem maintainers merge
patches that change the driver at the same time as the dts files. In
most cases this could be avoided because the dts changes are supposed
to be compatible in both ways, and we are asking everyone to send ARM
dts changes through our tree only.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=zl/N
-----END PGP SIGNATURE-----
Merge tag 'dt-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree changes from Arnd Bergmann:
"A large part of the arm-soc patches are nowadays DT changes, adding
support for new SoCs, boards and devices without changing kernel
source. The plan is still to move the devicetree files out of the
kernel tree and reduce the amount of churn going on here, but we keep
finding reasons to delay doing that.
Changes are really all over the place, with little sticking out
particularly. We have contributions from a total of 116 people in
this branch.
Unfortunately, the size of this branch also causes a significant
number of conflicts at the moment, typically when subsystem
maintainers merge patches that change the driver at the same time as
the dts files. In most cases this could be avoided because the dts
changes are supposed to be compatible in both ways, and we are asking
everyone to send ARM dts changes through our tree only"
* tag 'dt-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (541 commits)
dts: stmmac: Document the clocks property in the stmmac base document
dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac.
ARM: STi: stih41x: Add support for the FSM Serial Flash Controller
ARM: STi: stih416: Add support for the FSM Serial Flash Controller
ARM: tegra: fix Dalmore pinctrl configuration
ARM: dts: keystone: use common "ti,keystone" compatible instead of -evm
ARM: dts: k2hk-evm: set ubifs partition size for 512M NAND
ARM: dts: Build all keystone dt blobs
ARM: dts: keystone: Fix control register range for clktsip
ARM: dts: keystone: Fix domain register range for clkfftc1
ARM: dts: bcm28155-ap: leave camldo1 on to fix reboot
ARM: dts: add bcm590xx pmu support and enable for bcm28155-ap
ARM: dts: bcm21664: Add device tree files.
ARM: DT: bcm21664: Device tree bindings
ARM: efm32: properly namespace i2c location property
ARM: efm32: fix unit address part in USART2 device nodes' names
ARM: mvebu: Enable NAND controller in Armada 385-DB
ARM: mvebu: Add support for NAND controller in Armada 38x SoC
ARM: mvebu: Add the Core Divider clock to Armada 38x SoCs
ARM: mvebu: Add a 2 GHz fixed-clock on Armada 38x SoCs
...
Add the clocks and clock-names property to the base stmmac dts bindings
document.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch adds the dts bindings documenation for the Altera SOCFPGA glue
layer for the Synopsys STMMAC ethernet driver.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch adds binding document for SXGBE ethernet driver via device-tree.
Signed-off-by: Siva Reddy Kallam <siva.kallam@samsung.com>
Signed-off-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
Documentation/devicetree/bindings/net/micrel-ks8851.txt
net/core/netpoll.c
The net/core/netpoll.c conflict is a bug fix in 'net' happening
to code which is completely removed in 'net-next'.
In micrel-ks8851.txt we simply have overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Few platforms use external regulator to keep the ethernet MAC supplied.
So, request and enable the regulator for driver functionality.
Fixes: 66fda75f47 (regulator: core: Replace direct ops->disable usage)
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Suggested-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This describes a compatible entry of the form:
ethernet-phy-idAAAA,BBBB
Which is modelled after the PCI structured compatible entry
(pciVVVV,DDDD.SSSS.ssss.RR)
If present the OF core will be able to use this information to
directly create the correct phy without auto probing the bus.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a bindings description for the Altera Triple Speed Ethernet
(TSE) driver. The bindings support the legacy SGDMA soft IP as well as the
preferred MSGDMA soft IP. The TSE can be configured and synthesized in soft
logic using Altera's Quartus toolchain. Please consult the bindings document
for supported options.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the NFC pull request for 3.15. With this one we have:
- Support for ISO 15693 a.k.a. NFC vicinity a.k.a. Type 5 tags. ISO
15693 are long range (1 - 2 meters) vicinity tags/cards. The kernel
now supports those through the NFC netlink and digital APIs.
- Support for TI's trf7970a chipset. This chipset relies on the NFC
digital layer and the driver currently supports type 2, 4A and 5 tags.
- Support for NXP's pn544 secure firmare download. The pn544 C3 chipsets
relies on a different firmware download protocal than the C2 one. We
now support both and use the right one depending on the version we
detect at runtime.
- Support for 4A tags from the NFC digital layer.
- A bunch of cleanups and minor fixes from Axel Lin and Thierry Escande.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=xikL
-----END PGP SIGNATURE-----
Merge tag 'nfc-next-3.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-next
Samuel Ortiz <sameo@linux.intel.com> says:
"NFC: 3.15: First pull request
This is the NFC pull request for 3.15. With this one we have:
- Support for ISO 15693 a.k.a. NFC vicinity a.k.a. Type 5 tags. ISO
15693 are long range (1 - 2 meters) vicinity tags/cards. The kernel
now supports those through the NFC netlink and digital APIs.
- Support for TI's trf7970a chipset. This chipset relies on the NFC
digital layer and the driver currently supports type 2, 4A and 5 tags.
- Support for NXP's pn544 secure firmare download. The pn544 C3 chipsets
relies on a different firmware download protocal than the C2 one. We
now support both and use the right one depending on the version we
detect at runtime.
- Support for 4A tags from the NFC digital layer.
- A bunch of cleanups and minor fixes from Axel Lin and Thierry Escande."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Describe the properies used by the trf7970a
RFID/NFC/15693 transceiver driver.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Conflicts:
drivers/net/wireless/ath/ath9k/recv.c
drivers/net/wireless/mwifiex/pcie.c
net/ipv6/sit.c
The SIT driver conflict consists of a bug fix being done by hand
in 'net' (missing u64_stats_init()) whilst in 'net-next' a helper
was created (netdev_alloc_pcpu_stats()) which takes care of this.
The two wireless conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add device tree binding documentation for Texas Instrument's wl1251
wireless lan chip. For now only the SPI binding is documented.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for the led-mode property for the following PHYs
which have a single LED mode configuration value.
KSZ8001 and KSZ8041 which both use register 0x1e bits 15,14 and
KSZ8021, KSZ8031 and KSZ8051 which use register 0x1f bits 5,4
to control the LED configuration.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/bonding/bond_3ad.h
drivers/net/bonding/bond_main.c
Two minor conflicts in bonding, both of which were overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a typo in the Device Tree binding for the
leading '#'.
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support of the device tree probing for the Renesas SH-Mobile SoCs
documenting the device tree binding as necessary.
This work is loosely based on the original patch by Nobuhiro Iwamatsu
<nobuhiro.iwamatsu.yj@renesas.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is an attempt to gather the Ethernet related bindings in one file,
like it's done in the MMC and some other subsystems. It should save some of
the trouble of documenting several properties over and over in each binding
document, instead only making reference to the main file.
I have used the Embedded Power Architecture(TM) Platform Requirements (ePAPR)
standard as a base for the properties description, also documenting some ad-hoc
properties that have been introduced over time despite having direct analogs in
ePAPR.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Document the required "clocks" phandles and their corresponding
"clock-names" properties for the two clocks used by the GENET hardware
block ("enet" and "enet-wol").
CC: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the Device Tree bindings for the Broadcom GENET Gigabit
Ethernet controller. A bunch of examples are provided to illustrate the
versatile aspect of the hardare.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlL7RxcACgkQjTAFq1RaXHNcKACgk4Vj+1KlmWVEin8VPoJBX86m
RasAn36pSY1OszxypJOF0O1s0qO9ld5K
=383M
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-3.15-20140212' of git://gitorious.org/linux-can/linux-can-next
linux-can-next-for-3.15-20140212
Marc Kleine-Budde says:
====================
this is a pull request of eight patches for net-next/master.
Florian Vaussard contributed a series that merged the sja1000 of_platform
into the platform driver. The of_platform driver is finally removed.
Stephane Grosjean supplied a patch to allocate CANFD skbs. In a patch
by Uwe Kleine-König another missing copyright information was added to
a userspace header. And a patch by Yoann DI RUZZA that adds listen only
mode to the at91_can driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
STi series SOCs have a glue layer on top of the synopsis gmac IP, this
glue layer needs to be configured before the gmac driver starts using
the IP.
This patch adds a support to this glue layer which is configured via
stmmac setup, init, exit callbacks.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Allwinner A10 compatibles were following a slightly different compatible
patterns than the rest of the SoCs for historical reasons. Add compatibles
matching the other pattern to the mdio driver for consistency, and keep the
older one for backward compatibility.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Allwinner A10 compatibles were following a slightly different compatible
patterns than the rest of the SoCs for historical reasons. Add compatibles
matching the other pattern to the ethernet driver for consistency, and keep the
older one for backward compatibility.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the reg-io-width property to describe the width of the memory
accesses.
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: devicetree@vger.kernel.org
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Tested-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The "ti,davinci-no-bd-ram" property for the DaVinci EMAC binding simply can't be
required one, as it's boolean (which means it's absent if false).
While at it, document the property better...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Though described as required, the "ti,davinci-rmii-en" property for the DaVinci
EMAC binding seems actually optional, as the driver should happily work without
it; the property is not specified either in the example device node or in the
actual EMAC device node for DA850 device tree, only AM3517 one.
While at it, document the property better...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) BPF debugger and asm tool by Daniel Borkmann.
2) Speed up create/bind in AF_PACKET, also from Daniel Borkmann.
3) Correct reciprocal_divide and update users, from Hannes Frederic
Sowa and Daniel Borkmann.
4) Currently we only have a "set" operation for the hw timestamp socket
ioctl, add a "get" operation to match. From Ben Hutchings.
5) Add better trace events for debugging driver datapath problems, also
from Ben Hutchings.
6) Implement auto corking in TCP, from Eric Dumazet. Basically, if we
have a small send and a previous packet is already in the qdisc or
device queue, defer until TX completion or we get more data.
7) Allow userspace to manage ipv6 temporary addresses, from Jiri Pirko.
8) Add a qdisc bypass option for AF_PACKET sockets, from Daniel
Borkmann.
9) Share IP header compression code between Bluetooth and IEEE802154
layers, from Jukka Rissanen.
10) Fix ipv6 router reachability probing, from Jiri Benc.
11) Allow packets to be captured on macvtap devices, from Vlad Yasevich.
12) Support tunneling in GRO layer, from Jerry Chu.
13) Allow bonding to be configured fully using netlink, from Scott
Feldman.
14) Allow AF_PACKET users to obtain the VLAN TPID, just like they can
already get the TCI. From Atzm Watanabe.
15) New "Heavy Hitter" qdisc, from Terry Lam.
16) Significantly improve the IPSEC support in pktgen, from Fan Du.
17) Allow ipv4 tunnels to cache routes, just like sockets. From Tom
Herbert.
18) Add Proportional Integral Enhanced packet scheduler, from Vijay
Subramanian.
19) Allow openvswitch to mmap'd netlink, from Thomas Graf.
20) Key TCP metrics blobs also by source address, not just destination
address. From Christoph Paasch.
21) Support 10G in generic phylib. From Andy Fleming.
22) Try to short-circuit GRO flow compares using device provided RX
hash, if provided. From Tom Herbert.
The wireless and netfilter folks have been busy little bees too.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2064 commits)
net/cxgb4: Fix referencing freed adapter
ipv6: reallocate addrconf router for ipv6 address when lo device up
fib_frontend: fix possible NULL pointer dereference
rtnetlink: remove IFLA_BOND_SLAVE definition
rtnetlink: remove check for fill_slave_info in rtnl_have_link_slave_info
qlcnic: update version to 5.3.55
qlcnic: Enhance logic to calculate msix vectors.
qlcnic: Refactor interrupt coalescing code for all adapters.
qlcnic: Update poll controller code path
qlcnic: Interrupt code cleanup
qlcnic: Enhance Tx timeout debugging.
qlcnic: Use bool for rx_mac_learn.
bonding: fix u64 division
rtnetlink: add missing IFLA_BOND_AD_INFO_UNSPEC
sfc: Use the correct maximum TX DMA ring size for SFC9100
Add Shradha Shah as the sfc driver maintainer.
net/vxlan: Share RX skb de-marking and checksum checks with ovs
tulip: cleanup by using ARRAY_SIZE()
ip_tunnel: clear IPCB in ip_tunnel_xmit() in case dst_link_failure() is called
net/cxgb4: Don't retrieve stats during recovery
...
This change adds a parameter for the Synopsys 10/100/1000
stmmac Ethernet driver to configure the maximum frame
size supported by the EMAC driver. Synopsys allows the FIFO
sizes to be configured when the cores are built for a particular
device, but do not provide a way for the driver to read
information from the device about the maximum MTU size
supported as limited by the device's FIFO size.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Allwinner A20 has an ethernet controller that seems to be
an early version of Synopsys DesignWare MAC 10/100/1000 Universal,
which is supported by the stmmac driver.
Allwinner's GMAC requires setting additional registers in the SoC's
clock control unit.
The exact version of the DWMAC IP that Allwinner uses is unknown,
thus the exact feature set is unknown.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The snps,phy-addr device tree property is non-standard, and should be
removed in favor of proper phy node support. Remove it from the binding
documents and warn if the property is still used.
Most PHYs respond to address 0, but a few don't, so auto-detect PHY
address by default, to make up for the lack of explicit address selection.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DWMAC has a reset assert line, which is used on some SoCs. Add an
optional reset control to stmmac driver core.
To support reset control deferred probing, this patch changes the driver
probe function to return the actual error, instead of just -EINVAL.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Though described as required, the "phy-handle" property for the DaVinci EMAC
binding is actually optional, as the driver will happily function without it,
assuming 100/FULL link; the property is not specified either in the example
device node, or in the actual EMAC device nodes for DA850 and AM3517 device
trees.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macb driver uses the clock bindings. Document the required
properties, especially the driver specific clock-names.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Rob Herring <robh@kernel.org>
device_type is deprecated and the kernel doesn't require it in most
cases. The only exceptions for flat tree users are the "gianfar",
"ucc_geth" and "ibm,emac" bindings, and arguably that requirement could
be relaxed for ucc_geth and ibm,emac (that is a task for separate
patches though).
This patch removes references to device_type="network" from the binding
documentation where possible and removes the properties from ARM and
microblaze dts files. This patch does not modify the powerpc .dts files
since there are a much larger number of them affected and I think the
ucc_geth, ibm,emac and gianfar users should be addressed before clearing
out the references to reduce the chance of breakage.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Acked-by: Michal Simek <monstr@monstr.eu>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
The linux,phandle property is essentially an internal structural element
of the DT data structure. The dtc toolchain takes care of maintaining it
at compile time. It does not need to appear as part of the binding
documentation. This patch removes it so that users don't think they need
to add a phandle property manually.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
The device_type property is deprecated for the flattened device tree and
the value "ethernet-phy" has never been defined as having a useful
meaning. Neither the kernel nor u-boot depend on it. It should never
have appeared in PHY bindings. This patch removes all references to
"ethernet-phy" as a device_type value from the documentation and the
.dts files.
This patch was generated mechanically with the following command and
then verified by looking at the diff.
sed -i '/"ethernet-phy"/d' `git grep -l '"ethernet-phy"'`
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds Device Tree support to the Microchip MCP251X driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Conflicts:
drivers/net/ethernet/intel/i40e/i40e_main.c
drivers/net/macvtap.c
Both minor merge hassles, simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Revert CHECKSUM_COMPLETE optimization in pskb_trim_rcsum(), I can't
figure out why it breaks things.
2) Fix comparison in netfilter ipset's hash_netnet4_data_equal(), it
was basically doing "x == x", from Dave Jones.
3) Freescale FEC driver was DMA mapping the wrong number of bytes, from
Sebastian Siewior.
4) Blackhole and prohibit routes in ipv6 were not doing the right thing
because their ->input and ->output methods were not being assigned
correctly. Now they behave properly like their ipv4 counterparts.
From Kamala R.
5) Several drivers advertise the NETIF_F_FRAGLIST capability, but
really do not support this feature and will send garbage packets if
fed fraglist SKBs. From Eric Dumazet.
6) Fix long standing user triggerable BUG_ON over loopback in RDS
protocol stack, from Venkat Venkatsubra.
7) Several not so common code paths can potentially try to invoke
packet scheduler actions that might be NULL without checking. Shore
things up by either 1) defining a method as mandatory and erroring
on registration if that method is NULL 2) defininig a method as
optional and the registration function hooks up a default
implementation when NULL is seen. From Jamal Hadi Salim.
8) Fix fragment detection in xen-natback driver, from Paul Durrant.
9) Kill dangling enter_memory_pressure method in cg_proto ops, from
Eric W Biederman.
10) SKBs that traverse namespaces should have their local_df cleared,
from Hannes Frederic Sowa.
11) IOCB file position is not being updated by macvtap_aio_read() and
tun_chr_aio_read(). From Zhi Yong Wu.
12) Don't free virtio_net netdev before releasing all of the NAPI
instances. From Andrey Vagin.
13) Procfs entry leak in xt_hashlimit, from Sergey Popovich.
14) IPv6 routes that are no cached routes should not count against the
garbage collection limits. We had this almost right, but were
missing handling addrconf generated routes properly. From Hannes
Frederic Sowa.
15) fib{4,6}_rule_suppress() have to consider potentially seeing NULL
route info when they are called, from Stefan Tomanek.
16) TUN and MACVTAP have had truncated packet signalling for some time,
fix from Jason Wang.
17) Fix use after frrr in __udp4_lib_rcv(), from Eric Dumazet.
18) xen-netback does not interpret the NAPI budget properly for TX work,
fix from Paul Durrant.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (132 commits)
igb: Fix for issue where values could be too high for udelay function.
i40e: fix null dereference
xen-netback: fix gso_prefix check
net: make neigh_priv_len in struct net_device 16bit instead of 8bit
drivers: net: cpsw: fix for cpsw crash when build as modules
xen-netback: napi: don't prematurely request a tx event
xen-netback: napi: fix abuse of budget
sch_tbf: use do_div() for 64-bit divide
udp: ipv4: must add synchronization in udp_sk_rx_dst_set()
net:fec: remove duplicate lines in comment about errata ERR006358
Revert "8390 : Replace ei_debug with msg_enable/NETIF_MSG_* feature"
8390 : Replace ei_debug with msg_enable/NETIF_MSG_* feature
xen-netback: make sure skb linear area covers checksum field
net: smc91x: Fix device tree based configuration so it's usable
udp: ipv4: fix potential use after free in udp_v4_early_demux()
macvtap: signal truncated packets
tun: unbreak truncated packet signalling
net: sched: htb: fix the calculation of quantum
net: sched: tbf: fix the calculation of max_size
micrel: add support for KSZ8041RNLI
...
Commit 89ce376c6b (drivers/net: Use of_match_ptr() macro in smc91x.c)
added minimal device tree support to smc91x, but it's not working on
many platforms because of the lack of some key configuration bits.
Fix the issue by parsing the necessary configuration like the
smc911x driver is doing. As most smc91x users seem to use 16-bit
access, let's default to that if no reg-io-width is specified.
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: netdev@vger.kernel.org
Cc: devicetree@vger.kernel.org
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge 'net' into 'net-next' to get the AF_PACKET bug fix that
Daniel's direct transmit changes depend upon.
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'max-speed' property is optional but defined in the ePAPR
specification and now supported by the Linux Device Tree parsing
infrastructure.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When booted with device tree, we may still have platform data passed
as auxdata. For am3517 this is needed for passing the interrupt_enable
and interrupt_disable callbacks that access the omap system control module
registers. These callback functions will eventually go away when we have
a separate system control module driver.
Some of the things that are currently passed as platform data we don't need
to set up as device tree properties as they are always the same on am3517.
So let's use a new compatible flag for those so we can get those from
the device tree match data.
Also note that we need to fix setting of phy_dev to NULL instead of an empty
string as the code later on uses that to find the first phy on the mdio bus.
This seems to have been caused by 5d69e0076a (net: davinci_emac: switch to
new mdio).
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
