dw-mmc controller can support multiple slots.
But, there are no use-cases anywhere. So we don't need to support the
slot-node for dw-mmc controller.
And "supports-highspeed" property in dw-mmc is deprecated.
"supports-highspeed" property can be replaced with "cap-sd/mmc-highspeed".
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Tushar Behera <trblinux@gmail.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Sachin Kamat <sachin.kamat@samsung.com>
[kgene.kim@samsung.com: rebased exynos5250-snow changes]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Increase max i2c bus frequency beyond the default for faster
data transfers. According to the manual, these faster speeds are
only available when the board is wired up the right way. In this case,
the vendor kernel has run at this speed for a long time.
sda-delay is needed for talking to RTC on PMIC, otherwise the i2c
controller never sees an ACK. Strangely the other PMIC i2c slave (the
main one) works fine even without this delay. I Chose value 100 to
match the vendor kernel.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Tested-by: Tomeu Vizoso <tomeu@tomeuvizoso.net>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The ODROID kernel shows that the PMIC interrupt line is hooked up
to pin GPX3-2.
This is needed for the max77686-irq driver to create the PMIC IRQ
domain, which is needed by max77686-rtc.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Tested-by: Tomeu Vizoso <tomeu@tomeuvizoso.net>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add MAX98090 audio codec, I2S interface and the sound complex
nodes to enable audio on Odroid-X2/U3 boards.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
TFLASH (SDHCI2 controller) uses internal card detect line, but it looks
that the driver fails to operate it properly. Use GPIO interrupt on
SD_CDn line for detecting SD card state.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support for simple GPIO-based button availabled on
Exynos4 based Odroid boards. All supported boards have POWER button,
which has been defined in exynos4412-odroid-common.dtsi. X/X2 boards
also have additional user-configurable button which has been mapped to
KEY_HOME. All defined keys have been marked as possible wakeup source.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
On Odroid U2/U3 BUCK8 is used for providing power to also to P3V3
source, which is also connected to LAN9730 chip's nRESET signal. To
reset lan chip on system reboot, the BUCK8 output should not be used in
'always on' mode. This change has no impact on X/X2 boards.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch moves some parts of exynos4412-odroidx.dts to common
exynos4412-odroid-common.dtsi file and adds support for Odroid X2 and
U2/U3 boards. X2 is same as X, but it has faster SoC module (1.7GHz
instead of 1.4GHz), while U2/U3 differs from X2 by different way of
routing signals to host USB hub. It also lacks some hw modules not yet
supported by those dts files (i.e. LCD & touch panel).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
