Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
kernel-doc is not able to skip an #ifdef between the kernel documentation
block and the start of the struct. Moving the #ifdef before the kernel doc
block avoids this problem
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
We have found some networks in which nodes were constantly requesting
other nodes BLA claim tables to synchronize, just to ask for that again
once completed. The reason was that the crc checksum of the asked nodes
were out of sync due to missing locking and multiple writes to the same
crc checksum when adding/removing entries. Therefore the asked nodes
constantly reported the wrong crc, which caused repeating requests.
To avoid multiple functions changing a backbone gateways crc entry at
the same time, lock it using a spinlock.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Tested-by: Alfons Name <AlfonsName@web.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Since the function applies a threshold and also slightly worse
values are accepted, ''equal or better'' does not represent the
intention of the function. ''Similar or better'' represents that better.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
With rcu, the gateway node deleted attribute is not needed anymore. In
fact, it may delay the free of the gateway node and its referenced
structures. Therefore remove it altogether and simplify purging as well.
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Since the list's tail is never accessed using a double linked list head
wastes memory.
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Since the list's tail is never accessed using a double linked list head
wastes memory.
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
(s|u)(8|16|32|64) are the preferred types in the kernel. The use of the
standard C99 types u?int(8|16|32|64)_t are objected by some people and even
checkpatch now warns about using them.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
So far the mcast tvlv handler did not anticipate the processing of
multiple incoming OGMs from the same originator at the same time. This
can lead to various issues:
* Broken refcounting: For instance two mcast handlers might both assume
that an originator just got multicast capabilities and will together
wrongly decrease mcast.num_disabled by two, potentially leading to
an integer underflow.
* Potential kernel panic on hlist_del_rcu(): Two mcast handlers might
one after another try to do an
hlist_del_rcu(&orig->mcast_want_all_*_node). The second one will
cause memory corruption / crashes.
(Reported by: Sven Eckelmann <sven@narfation.org>)
Right in the beginning the code path makes assumptions about the current
multicast related state of an originator and bases all updates on that. The
easiest and least error prune way to fix the issues in this case is to
serialize multiple mcast handler invocations with a spinlock.
Fixes: 60432d756c ("batman-adv: Announce new capability via multicast TVLV")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Bitwise OR/AND assignments in C aren't guaranteed to be atomic. One
OGM handler might undo the set/clear of a specific bit from another
handler run in between.
Fix this by using the atomic set_bit()/clear_bit()/test_bit() functions.
Fixes: 60432d756c ("batman-adv: Announce new capability via multicast TVLV")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Bitwise OR/AND assignments in C aren't guaranteed to be atomic. One
OGM handler might undo the set/clear of a specific bit from another
handler run in between.
Fix this by using the atomic set_bit()/clear_bit()/test_bit() functions.
Fixes: e17931d1a6 ("batman-adv: introduce capability initialization bitfield")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Bitwise OR/AND assignments in C aren't guaranteed to be atomic. One
OGM handler might undo the set/clear of a specific bit from another
handler run in between.
Fix this by using the atomic set_bit()/clear_bit()/test_bit() functions.
Fixes: 3f4841ffb3 ("batman-adv: tvlv - add network coding container")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Bitwise OR/AND assignments in C aren't guaranteed to be atomic. One
OGM handler might undo the set/clear of a specific bit from another
handler run in between.
Fix this by using the atomic set_bit()/clear_bit()/test_bit() functions.
Fixes: 17cf0ea455 ("batman-adv: tvlv - add distributed arp table container")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
The header files could not be build indepdent from each other. This is
happened because headers didn't include the files for things they've used.
This was problematic because the success of a build depended on the
knowledge about the right order of local includes.
Also source files were not including everything they've used explicitly.
Instead they required that transitive includes are always stable. This is
problematic because some transitive includes are not obvious, depend on
config settings and may not be stable in the future.
The order for include blocks are:
* primary headers (main.h and the *.h file of a *.c file)
* global linux headers
* required local headers
* extra forward declarations for pointers in function/struct declarations
The only exceptions are linux/bitops.h and linux/if_ether.h in packet.h.
This header file is shared with userspace applications like batctl and must
therefore build together with userspace applications. The header
linux/bitops.h is not part of the uapi headers and linux/if_ether.h
conflicts with the musl implementation of netinet/if_ether.h. The
maintainers rejected the use of __KERNEL__ preprocessor checks and thus
these two headers are only in main.h. All files using packet.h first have
to include main.h to work correctly.
Reported-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
This API has to be used to let any routing protocol free
neighbor specific allocated resources
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
batadv_orig_bat_iv->bcast_own is actually not a bitfield, it is an
array. Adjust the comment accordingly.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
The fragmentation code was replaced in
610bfc6bc9 ("batman-adv: Receive fragmented
packets and merge") by an implementation which handles the queueing+merging
of fragments based on their size and the total_size of the non-fragmented
packet. This total_size is announced by each fragment. The new
implementation doesn't check if the the total_size information of the
packets inside one chain is consistent.
This is consistency check is recommended to allow using any of the packets
in the queue to decide whether all fragments of a packet are received or
not.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
This variable became obsolete when changing to the new bonding mechanism
based on the multi interface optimization. Since its not used anywhere,
remove it.
Reported-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
When a VLAN interface (on top of batX) is removed and
re-added within a short timeframe TT does not have enough
time to properly cleanup. This creates an internal TT state
mismatch as the newly created softif_vlan will be
initialized from scratch with a TT client count of zero
(even if TT entries for this VLAN still exist). The
resulting TT messages are bogus due to the counter / tt
client listing mismatch, thus creating inconsistencies on
every node in the network
To fix this issue destroy_vlan() has to not free the VLAN
object immediately but it has to be kept alive until all the
TT entries for this VLAN have been removed. destroy_vlan()
still removes the sysfs folder so that the user has the
feeling that everything went fine.
If the same VLAN is re-added before the old object is free'd,
then the latter is resurrected and re-used.
Implement such behaviour by increasing the reference counter
of a softif_vlan object every time a new local TT entry for
such VLAN is created and remove the object from the list
only when all the TT entries have been destroyed.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Add missing documentation for BATADV_DAT_ADDR_MAX and
convert an existing documentation to kerneldoc
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
With this patch a node sends IPv4 multicast packets to nodes which
have a BATADV_MCAST_WANT_ALL_IPV4 flag set and IPv6 multicast packets
to nodes which have a BATADV_MCAST_WANT_ALL_IPV6 flag set, too.
Why is this needed? There are scenarios involving bridges where
multicast report snooping and multicast TT announcements are not
sufficient, which would lead to packet loss for some nodes otherwise:
MLDv1 and IGMPv1/IGMPv2 have a suppression mechanism
for multicast listener reports. When we have an MLDv1/IGMPv1/IGMPv2
querier behind a bridge then our snooping bridge is potentially not
going to see any reports even though listeners exist because according
to RFC4541 such reports are only forwarded to multicast routers:
-----------------------------------------------------------
---------------
{Querier}---|Snoop. Switch|----{Listener}
---------------
\ ^
-------
| br0 | < ???
-------
\
_-~---~_
_-~/ ~-_
~ batman-adv \-----{Sender}
\~_ cloud ~/
-~~__-__-~_/
I) MLDv1 Query: {Querier} -> flooded
II) MLDv1 Report: {Listener} -> {Querier}
-> br0 cannot detect the {Listener}
=> Packets from {Sender} need to be forwarded to all
detected listeners and MLDv1/IGMPv1/IGMPv2 queriers.
-----------------------------------------------------------
Note that we do not need to explicitly forward to MLDv2/IGMPv3 queriers,
because these protocols have no report suppression: A bridge has no
trouble detecting MLDv2/IGMPv3 listeners.
Even though we do not support bridges yet we need to provide the
according infrastructure already to not break compatibility later.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
With this patch a node may additionally perform the dropping or
unicasting behaviour for a link-local IPv4 and link-local-all-nodes
IPv6 multicast packet, too.
The extra counter and BATADV_MCAST_WANT_ALL_UNSNOOPABLES flag is needed
because with a future bridge snooping support integration a node with a
bridge on top of its soft interface is not able to reliably detect its
multicast listeners for IPv4 link-local and the IPv6
link-local-all-nodes addresses anymore (see RFC4541, section 2.1.2.2
and section 3).
Even though this new flag does make "no difference" now, it'll ensure
a seamless integration of multicast bridge support without needing to
break compatibility later.
Also note, that even with multicast bridge support it won't be possible
to optimize 224.0.0.x and ff02::1 towards nodes with bridges, they will
always receive these ranges.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
With this patch a multicast packet is not always simply flooded anymore,
the behaviour for the following cases is changed to reduce
unnecessary overhead:
If all nodes within the horizon of a certain node have signalized
multicast listener announcement capability then an IPv6 multicast packet
with a destination of IPv6 link-local scope (excluding ff02::1) coming
from the upstream of this node...
* ...is dropped if there is no according multicast listener in the
translation table,
* ...is forwarded via unicast if there is a single node with interested
multicast listeners
* ...and otherwise still gets flooded.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
If the soft interface of a node is not part of a bridge then a node
announces a new multicast TVLV: The existence of this TVLV
signalizes that this node is announcing all of its multicast listeners
via the translation table infrastructure.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
The new bitfield allows us to keep track whether capability subsets of
an originator have gone through their initialization phase yet.
The translation table is the only user right now, but a new one will be
added soon.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
With this patch a node which has no bridge interface on top of its soft
interface announces its local multicast listeners via the translation
table.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Reported-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Reported-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Show tables for the multi interface operation. Originator tables
are added per hard interface.
This patch also changes the API by adding the interface to the
bat_orig_print() parameters.
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
To show information per interface, add a debugfs hardif structure
similar to the system in sysfs. Hard interface folders will be created
in "$debugfs/batman-adv/". Files are not yet added.
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
With the new interface alternating, the first hop may send packets
in a round robin fashion to it's neighbors because it has multiple
valid routes built by the multi interface optimization. This patch
enables the feature if bonding is selected. Note that unlike the
bonding implemented before, this version is much simpler and may
even enable multi path routing to a certain degree.
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
The current OGM sending an aggregation functionality decides on
which interfaces a packet should be sent when it parses the forward
packet struct. However, with the network wide multi interface
optimization the outgoing interface is decided by the OGM processing
function.
This is reflected by moving the decision in the OGM processing function
and add the outgoing interface in the forwarding packet struct. This
practically implies that an OGM may be added multiple times (once per
outgoing interface), and this also affects aggregation which needs to
consider the outgoing interface as well.
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
For the network wide multi interface optimization there are different
routers for each outgoing interface (outgoing from the OGM perspective,
incoming for payload traffic). To reflect this, change the router and
associated data to a list of routers.
While at it, rename batadv_orig_node_get_router() to
batadv_orig_router_get() to follow the new naming scheme.
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
For the network wide multi interface optimization it is required to save
metrics per outgoing interface in one neighbor. Therefore a new type is
introduced to keep interface-specific information. This also requires
some changes in access and list management.
The compare and equiv_or_better API calls are changed to take the
outgoing interface into consideration.
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Remove bonding and interface alternating code - it will be replaced
by a new, network-wide multi interface optimization which enables
both bonding and interface alternating in a better way.
Keep the sysfs and find router function though, this will be needed
later.
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
This attribute can be used to set and read the value and the
mask of the skb mark which will be used to classify the
source non-mesh client as ISOLATED. In this way a client can
be advertised as such and the mark can potentially be
restored at the receiving node before delivering the skb.
This can be helpful for creating network wide netfilter
policies.
This sysfs file expects a string of the shape "$mark/$mask".
Where $mark has to be a 32-bit number in any base, while
$mask must be a 32bit mask expressed in hex base. Only bits
in $mark covered by the bitmask are really stored.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
In different situations it is possible that the DHCP server
or client uses broadcast Ethernet frames to send messages
to each other. The GW component in batman-adv takes care of
using bat-unicast packets to bring broadcast DHCP
Discover/Requests to the "best" server.
On the way back the DHCP server usually sends unicasts,
but upon client request it may decide to use broadcasts as
well.
This patch improves the GW component so that it now snoops
and sends as unicast all the DHCP packets, no matter if they
were generated by a DHCP server or client.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
As suggested by checkpatch, remove all the references to the
FSF address since the kernel already has one reference in
its documentation.
In this way it is easier to update it in case of future
changes.
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Instead of handling icmp packets only up to length of icmp_packet_rr,
the code should handle any icmp length size. Therefore the length
truncating is moved to when the packet is actually sent to userspace
(this does not support lengths longer than icmp_packet_rr yet). Longer
packets are forwarded without truncating.
This patch also cleans up some parts where the icmp header struct could
be used instead of other icmp_packet(_rr) structs to make the code more
readable.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Flags covered by TT_SYNC_MASK are kept in sync among the
nodes in the network and therefore they have to be
considered while computing the global/local table CRC.
In this way a generic originator is able to understand if
its table contains the correct flags or not.
Bits from 4 to 7 in the TT flags fields are now reserved for
"synchronized" flags only.
This allows future developers to add more flags of this type
without breaking compatibility.
It's important to note that not all the remote TT flags are
synchronised. This comes from the fact that some flags are
used to inject an information once only.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Some flags (i.e. the WIFI flag) may change after that the
related client has already been announced. However it is
useful to informa the rest of the network about this change.
Add a runtime-flag-switch detection mechanism and
re-announce the related TT entry to advertise the new flag
value.
This mechanism can be easily exploited by future flags that
may need the same treatment.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
The local translation table size is limited by what can be
transferred from one node to another via a full table request.
The number of entries fitting into a full table request depend
on whether the fragmentation is enabled or not. Therefore this
patch introduces a max table size check and refuses to add
more local clients when that size is reached. Moreover, if the
max full table packet size changes (MTU change or fragmentation
is disabled) the local table is downsized instantaneously.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Acked-by: Antonio Quartulli <ordex@autistici.org>
