The Linux kernel coding style guidelines suggest not using typedefs
for structure types. This patch gets rid of the typedef for board_info_t.
Also, the name of the structs is changed to drop the _t, to make the
name look less typedef-like.
The following Coccinelle semantic patch detects the cases:
@tn@
identifier i;
type td;
@@
-typedef
struct i { ... }
-td
;
@@
type tn.td;
identifier tn.i;
@@
-td
+ struct i
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dm9000_release_board() function is called with NULL ->data_req and
->addr_req pointers if dm9000_probe() fails.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the DM9000B, dm9000_msleep() is called during the dm9000_timeout()
routine. Since dm9000_timeout() holds the main spinlock through the
entire routine, mdelay() needs to be used rather than msleep().
Furthermore, the mutex_lock()/mutex_unlock() should be avoided so as to
not sleep with spinlocks held.
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the DM9000A/DM9000B force the initial check of the link status. The
DM9000A/B has a link status changed event and this interrupt bit isn't
always set out of reset when a cable is plugged in. This results in the
driver not seeing the cable attached link status until the cable is
removed and plugged in again.
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since dm9000_interrupt() is already reading/clearing every set bit in
DM9000_ISR, this additional clear in dm9000_rx() (which is only called
by dm9000_interrupt()) is unnecessary and can be removed.
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DM9000 uses level-triggered interrupts. Some systems (PXA270) only
support edge-triggered interrupts on GPIOs. Some changes are necessary
to ensure that interrupts are not triggered while the GPIO interrupt is
masked or we will miss the interrupt forever.
* Make some helper functions called dm9000_mask_interrupts() and
dm9000_unmask_interrupts() for readability.
* dm9000_init_dm9000(): ensure that this function always leaves interrupts
masked regardless of the state when it entered the function. This is
primarily to support the situation in dm9000_open where the logic used
to go:
dm9000_open()
dm9000_init_dm9000()
unmask interrupts
request_irq()
If an interrupt occurred between unmasking the interrupt and
requesting the irq, it would be missed forever as the edge event would
never be seen by the GPIO hardware in the PXA270. This allows us to
change the logic to:
dm9000_open()
dm9000_init_dm9000()
dm9000_mask_interrupts()
request_irq()
dm9000_unmask_interrupts()
* dm9000_timeout(), dm9000_drv_resume(): Add the missing
dm9000_unmask_interrupts() now required by the change above.
* dm9000_shutdown(): Use mask helper function
* dm9000_interrupt(): Use mask/unmask helper functions
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Change a hard-coded 0x3 to NCR_RST | NCR_MAC_LBK in dm9000_reset
* Every single place where dm9000_init_dm9000 was ran, a dm9000_reset
was called immediately before-hand. Bring dm9000_reset into
dm9000_init_dm9000.
* The following commit updated the dm9000_probe reset routine to use NCR_RST
| NCR_MAC_LBK:
6741f40 DM9000B: driver initialization upgrade
and a later commit added a bug-fix to always reset the chip twice:
09ee9f8 dm9000: Implement full reset of DM9000 network device
Unfortunately, since the changes in 6741f40 were made by replacing the
dm9000_probe dm9000_reset with the adjusted iow(), the changes in
09ee9f8 were not incorporated into the dm9000_probe reset.
Furthermore, it bypassed the requisite reset-delay causing some boards
to get at least one "read wrong id ..." dev_err message during
dm9000_probe.
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DM9000 supports both active high interrupts and active low interrupts.
This is configured via the attached EEPROM. In the device-tree case, make sure
that the DM9000 driver passes the correct flags to request_irq.
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace dev_kfree_skb with dev_consume_skb_any in dm9000_start_xmit
that can be called in hard irq and other contexts, on the path
that successfully transmits the packet.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
recently, dm9000 codes have many checkpatch errors and warnings:
WARNING: please, no space before tabs
3: FILE: dm9000.c:3:
+ * ^ICopyright (C) 1997 Sten Wang$
WARNING: please, no space before tabs
5: FILE: dm9000.c:5:
+ * ^IThis program is free software; you can redistribute it and/or$
WARNING: please, no space before tabs
6: FILE: dm9000.c:6:
+ * ^Imodify it under the terms of the GNU General Public License$
WARNING: please, no space before tabs
7: FILE: dm9000.c:7:
+ * ^Ias published by the Free Software Foundation; either version 2$
WARNING: please, no space before tabs
8: FILE: dm9000.c:8:
+ * ^Iof the License, or (at your option) any later version.$
WARNING: please, no space before tabs
10: FILE: dm9000.c:10:
+ * ^IThis program is distributed in the hope that it will be useful,$
WARNING: please, no space before tabs
11: FILE: dm9000.c:11:
+ * ^Ibut WITHOUT ANY WARRANTY; without even the implied warranty of$
WARNING: please, no space before tabs
12: FILE: dm9000.c:12:
+ * ^IMERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the$
WARNING: please, no space before tabs
13: FILE: dm9000.c:13:
+ * ^IGNU General Public License for more details.$
WARNING: do not add new typedefs
97: FILE: dm9000.c:97:
+typedef struct board_info {
ERROR: spaces prohibited around that ':' (ctx:WxV)
113: FILE: dm9000.c:113:
+ unsigned int in_suspend :1;
^
ERROR: spaces prohibited around that ':' (ctx:WxV)
114: FILE: dm9000.c:114:
+ unsigned int wake_supported :1;
^
This patch fixes important errors in it.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
This covers everything under drivers/net except for wireless, which
has been submitted separately.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/qmi_wwan.c
include/net/dst.h
Trivial merge conflicts, both were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Report the LPA by checking mii_if_info, instead of just saying "no LPA" every
time.
Cc: David S. Miller <davem@davemloft.net>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
A Davicom application note for the DM9000 network device recommends
performing software reset twice to correctly initialise the device.
Without this reset some devices fail to initialise correctly on
system startup.
Cc: David S. Miller <davem@davemloft.net>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Michael Abbott <michael.abbott@diamond.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Take the phy out of reset explicitly during system resume to avoid
losing network connectivity.
Cc: David S. Miller <davem@davemloft.net>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the changes introduced in commit 6741f40 (DM9000B: driver
initialization upgrade) break functionality on DM9000A
(error message during NFS boot: "dm9000 dm9000.0: eth0: link down")
Since the changes were meant to serve only DM9000B, make them
dependent on the chip type.
Cc: David S. Miller <davem@davemloft.net>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the memset/memcpy uses of 6 to ETH_ALEN
where appropriate.
Also convert some struct definitions and u8 array
declarations of [6] to ETH_ALEN.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All drivers that select MII also need to select NET_CORE because MII
depends on it. This is a bit ridiculous because NET_CORE is just a
menu option that doesn't enable any code by itself.
There is also no need for it to be a visible option, since its users
all select it.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Roland Stigge <stigge@antcom.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Tested-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds Device Tree support to dm9000 driver.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Reviewed-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean up the code a bit to initialize the variables directly when
defining them.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/mac80211/sta_info.c
net/wireless/core.h
Two minor conflicts in wireless. Overlapping additions of extern
declarations in net/wireless/core.h and a bug fix overlapping with
the addition of a boolean parameter to __ieee80211_key_free().
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix bug for DM9000 revision B which contain a DSP PHY
DM9000B use DSP PHY instead previouse DM9000 revisions' analog PHY,
So need extra change in initialization, For
explicity PHY Reset and PHY init parameter, and
first DM9000_NCR reset need NCR_MAC_LBK bit by dm9000_probe().
Following DM9000_NCR reset cause by dm9000_open() clear the
NCR_MAC_LBK bit.
Without this fix, Power-up FIFO pointers error happen around 2%
rate among Davicom's customers' boards. With this fix, All above
cases can be solved.
Signed-off-by: Joseph CHANG <josright123@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
module_platform_driver macro removes some boilerplate and makes
the code simpler.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use strlcpy where possible to ensure the string is \0 terminated.
Use always sizeof(string) instead of 32, ETHTOOL_BUSINFO_LEN
and custom defines.
Use snprintf instead of sprint.
Remove unnecessary inits of ->fw_version
Remove unnecessary inits of drvinfo struct.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
The {read,write}s{b,w,l} operations are not defined by all
architectures and are being removed from the asm-generic/io.h
interface.
This patch replaces the usage of these string functions in the default
DM9000 accessors with io{read,write}{8,16,32}_rep calls instead. This
is required as the dm9000 driver is in use by the blackfin
architecture which uses the asm-generic io accessors.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Ben Herrenschmidt <benh@kernel.crashing.org>
Cc: David Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Matthew Leach <matthew@mattleach.net>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some coldfire boards (ie m5253demo) have a dm9000 onboard.
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace usage of random_ether_addr() with eth_hw_addr_random()
to set addr_assign_type correctly to NET_ADDR_RANDOM.
Change the trivial cases.
v2: adapt to renamed eth_hw_addr_random()
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replaced deprecating dev_alloc_skb with netdev_alloc_skb in drivers/net/ethernet
- Removed extra skb->dev = dev after netdev_alloc_skb
Signed-off-by: Pradeep A Dalvi <netdev@pradeepdalvi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_etherdev has a generic OOM/unable to alloc message.
Remove the duplicative messages after alloc_etherdev calls.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're trying to check if any options are defined which isn't wha the
existing code does due to confusing & and &&.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
v2: add couple missing conversions in drivers
split unexporting netdev_fix_features()
implemented %pNF
convert sock::sk_route_(no?)caps
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
MII Kconfig option is apart of the core networking drivers and
by default NET_CORE is enabled so drivers selecting MII will
have MII enabled as well. It was found using the randconfig
option during testing, MII would be selected but NET_CORE
could be disabled. This caused a dependency error.
Resolved the dependency by selecting NET_CORE when MII is
selected.
Reported-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change allows to get driver specific debug messages output
providing a module parameter. As far as the maximum level of verbosity
is too high, it is demoted by default.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the Davicom driver into drivers/net/ethernet/davicom/ and
make the necessary Kconfig and Makefile changes.
CC: Ben Dooks <ben@simtec.co.uk>
CC: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
