As defined in the anx7625 dt-binding, the analogix,lane0-swing and
analogix,lane1-swing properties are uint8 arrays. Yet, the driver was
reading the array as if it were of uint32 and masking to 8-bit before
writing to the registers. This means that a devicetree written in
accordance to the dt-binding would have its values incorrectly parsed.
Fix the issue by reading the array as uint8 and storing them as uint8
internally, so that we can also drop the masking when writing the
registers.
Fixes: fd0310b6fe ("drm/bridge: anx7625: add MIPI DPI input feature")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220408013034.673418-1-nfraprado@collabora.com
If panel_bridge_attach() happens after DRM device registration, the
created connector will not be registered by the DRM core anymore. Fix
this by registering it explicitly in such case.
This fixes the following issue observed on Samsung Exynos4210-based Trats
board with a DSI panel (the panel driver is registered after the Exynos DRM
component device is bound):
$ ./modetest -c -Mexynos
could not get connector 56: No such file or directory
Segmentation fault
While touching this, move the connector reset() call also under the DRM
device registered check, because otherwise it is not really needed.
Fixes: 934aef885f ("drm: bridge: panel: Reset the connector state pointer")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220419091422.4255-1-m.szyprowski@samsung.com
Add driver for Lontium LT9211 Single/Dual-Link DSI/LVDS or Single DPI to
Single-link/Dual-Link DSI/LVDS or Single DPI bridge. This chip is highly
capable at converting formats, but sadly it is also highly undocumented.
This driver is written without any documentation from Lontium and based
only on shreds of information available in various obscure example codes,
hence long runs of unknown register patches and lengthy delays in various
places. Whichever register meaning could be divined from its behavior has
at least a comment around it.
Currently the only mode tested is Single-link DSI to Single-link LVDS.
Dual-link LVDS might work as well, the register programming is in place,
but is untested.
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
To: dri-devel@lists.freedesktop.org
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220419143958.94873-2-marex@denx.de
drm/drm-next has a build fix for the NewVision NV3052C panel
(drivers/gpu/drm/panel/panel-newvision-nv3052c.c), which needs to be
merged back to drm-misc-next, as it was failing to build there.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Let's make sure FBC is always disabled when we start to take
over the hardware state.
I suspect this should never really happen, since the only time
when we really should be taking over with the display already
active is when the previous state was progammed by the BIOS,
which likely shouldn't use FBC. This could be driver init,
or S4 resume when the boot kernel doesn't load i915. But I
suppose no harm in keeping this code around for exra safety
since it's quite trivial.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220315140001.1172-7-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
With some VRR panels, user can turn VRR ON/OFF on the fly from the panel settings.
When VRR is turned OFF ,sends a long HPD to the driver clearing the Ignore MSA bit
in the DPCD. Currently the driver parses that onevery HPD but fails to reset
the corresponding VRR Capable Connector property.
Hence the userspace still sees this as VRR Capable panel which is incorrect.
Fix this by explicitly resetting the connector property.
v2: Reset vrr capable if status == connector_disconnected
v3: Use i915 and use bool vrr_capable (Jani Nikula)
v4: Move vrr_capable to after update modes call (Jani N)
Remove the redundant comment (Jan N)
v5: Fixes the regression on older platforms by resetting the VRR
only if HAS_VRR
v6: Remove the checks from driver, add in drm core before
setting VRR prop (Ville)
v7: Move VRR set/reset to set/unset_edid (Ville)
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Fixes: 9bc34b4d0f ("drm/i915/display/vrr: Reset VRR capable property on a long hpd")
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220303233222.4698-1-manasi.d.navare@intel.com
Add support for the DG2 specific render compression with clear color
framebuffer format.
DG2 onwards discrete gfx has support for new flat CCS mapping,
which brings in display feature in to avoid Aux walk for compressed
surface. This support build on top of Flat CCS support added in XEHPSDV.
FLAT CCS surface base address should be 64k aligned,
Compressed displayable surfaces must use tile4 format.
HAS: 1407880786
B.Spec : 7655
B.Spec : 53902
v2: Merge all bits required for the support of functionality into this
patch from the patch adding the corresponding modifier.
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Juha-Pekka Heikkilä <juha-pekka.heikkila@intel.com>
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Acked-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220411143405.1073845-5-imre.deak@intel.com
drm-misc-next for 5.19:
UAPI Changes:
Cross-subsystem Changes:
Core Changes:
- atomic: Add atomic_print_state to private objects
- edid: Constify the EDID parsing API, rework of the API
- dma-buf: Add dma_resv_replace_fences, dma_resv_get_singleton, make
dma_resv_excl_fence private
- format: Support monochrome formats
- fbdev: fixes for cfb_imageblit and sys_imageblit, pagelist
corruption fix
- selftests: several small fixes
- ttm: Rework bulk move handling
Driver Changes:
- Switch all relevant drivers to drm_mode_copy or drm_mode_duplicate
- bridge: conversions to devm_drm_of_get_bridge and panel_bridge,
autosuspend for analogix_dp, audio support for it66121, DSI to DPI
support for tc358767, PLL fixes and I2C support for icn6211
- bridge_connector: Enable HPD if supported
- etnaviv: fencing improvements
- gma500: GEM and GTT improvements, connector handling fixes
- komeda: switch to plane reset helper
- mediatek: MIPI DSI improvements
- omapdrm: GEM improvements
- panel: DT bindings fixes for st7735r, few fixes for ssd130x, new
panels: ltk035c5444t, B133UAN01, NV3052C
- qxl: Allow to run on arm64
- sysfb: Kconfig rework, support for VESA graphic mode selection
- vc4: Add a tracepoint for CL submissions, HDMI YUV output,
HDMI and clock improvements
- virtio: Remove restriction of non-zero blob_flags,
- vmwgfx: support for CursorMob and CursorBypass 4, various
improvements and small fixes
[airlied: fixup conflict with newvision panel callbacks]
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220407085940.pnflvjojs4qw4b77@houat
struct drm_display_mode embeds a list head, so overwriting
the full struct with another one will corrupt the list
(if the destination mode is on a list). Use drm_mode_copy()
instead which explicitly preserves the list head of
the destination mode.
Even if we know the destination mode is not on any list
using drm_mode_copy() seems decent as it sets a good
example. Bad examples of not using it might eventually
get copied into code where preserving the list head
actually matters.
Obviously one case not covered here is when the mode
itself is embedded in a larger structure and the whole
structure is copied. But if we are careful when copying
into modes embedded in structures I think we can be a
little more reassured that bogus list heads haven't been
propagated in.
@is_mode_copy@
@@
drm_mode_copy(...)
{
...
}
@depends on !is_mode_copy@
struct drm_display_mode *mode;
expression E, S;
@@
(
- *mode = E
+ drm_mode_copy(mode, &E)
|
- memcpy(mode, E, S)
+ drm_mode_copy(mode, E)
)
@depends on !is_mode_copy@
struct drm_display_mode mode;
expression E;
@@
(
- mode = E
+ drm_mode_copy(&mode, &E)
|
- memcpy(&mode, E, S)
+ drm_mode_copy(&mode, E)
)
@@
struct drm_display_mode *mode;
@@
- &*mode
+ mode
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220218100403.7028-23-ville.syrjala@linux.intel.com
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Initialize on-stack modes with drm_mode_init() to guarantee
no stack garbage in the list head, or that we aren't copying
over another mode's list head.
Based on the following cocci script, with manual fixups:
@decl@
identifier M;
expression E;
@@
- struct drm_display_mode M = E;
+ struct drm_display_mode M;
@@
identifier decl.M;
expression decl.E;
statement S, S1;
@@
struct drm_display_mode M;
... when != S
+ drm_mode_init(&M, &E);
+
S1
@@
expression decl.E;
@@
- &*E
+ E
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220218100403.7028-22-ville.syrjala@linux.intel.com
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
In addition to the fp_timing,dvo_timing,panel_pnp_id tables
there also exists a panel_name table. Unlike the others this
is just one offset+table_size even though there are still 16
actual panel_names in the data block.
The panel_name table made its first appearance somewhere
around VBT version 156-163. The exact version is not known.
But we don't need to know that since we can just check whether
the pointers block has enough room for it or not.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220405173410.11436-7-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
