ENDPTFLUSH and ENDPTPRIME registers are set by software and clear
by hardware. There is a bit for each endpoint. When we are setting
a bit for an endpoint we should make sure we do not touch other
endpoint bit. There is a race condition if the hardware clear the
bit between the read and the write in hw_write.
Cc: stable <stable@vger.kernel.org> # 3.11+
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Matthieu CASTET <matthieu.castet@parrot.com>
Tested-by: Michael Grzeschik <mgrzeschik@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have met a bug that the high bandwidth ISO-TX transfer has failed
at the last packet if it is less than 1024, the TD status shows it
is "Transaction Error".
The root cause of this problem is: the mult value at qh is not correct
for current TD's transfer length. We use TD list to queue un-transfer
TDs, and change mult for new adding TDs. If new adding TDs transfer length
less than 1024, but the queued un-transfer TDs transfer length is larger
than 1024, the transfer error will occur, and vice versa.
Usually, this problem occurs at the last packet, and the first packet for
new frame.
We fixed this problem by setting Mult at QH as the largest value (3), and
set MultO (Multiplier Override) at TD according to every transfer length.
It can cover both hardware version less than 2.3 (the real mult is MultO
if it is not 0) and 2.3+ (the real mult is min(qh.mult, td.multo)).
Since the MultO bits are only existed at TX TD, we keep the ISO-RX behavior
unchanged.
For stable tree: 3.11+.
Cc: stable <stable@vger.kernel.org>
Cc: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reported-by: Matthieu Vanin <b47495@freescale.com>
Tested-by: Matthieu Vanin <b47495@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For otgsc, both enable bits and status bits are in it. So we need
to make sure the status bits are not be cleared when write enable
bits. It can fix one bug that we plug in/out Micro AB cable fast,
and sometimes, the IDIS will be cleared wrongly when handle last
ID interrupt (ID 0->1), so the current interrupt will not occur.
For stable tree: 3.12+
Cc: stable@vger.kernel.org
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hw_phymode_configure configures the PORTSC registers and allow the
following phy_inits to operate on the right parameters. This fix a problem
where the UPLI (ISP1504) could not be detected, because the Viewport was not
available and read the viewport return 0's only.
Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* init the sts flag to 0 (missed)
* fix write the real bit not sts value
* Set PORTCS_STS and DEVLC_STS only if sts = 1
[Peter Chen: This one and the next patch fix the problem occurred imx27
and imx31, and imx27 and imx31 usb support are enabled until 3.14, so
these two patches isn't needed for -stable]
Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to imx28 needs ARM swp instruction for writing, we set
CI_HDRC_IMX28_WRITE_FIX for imx28.
This patch is needed for stable tree 3.11+
Cc: stable@vger.kernel.org
Cc: robert.hodaszi@digi.com
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to Freescale imx28 Errata, "ENGR119653 USB: ARM to USB
register error issue", All USB register write operations must
use the ARM SWP instruction. So, we implement special hw_write
and hw_test_and_clear for imx28.
Discussion for it at below:
http://marc.info/?l=linux-usb&m=137996395529294&w=2
This patch is needed for stable tree 3.11+.
Cc: stable@vger.kernel.org
Cc: robert.hodaszi@digi.com
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 30666249ea, as it
depended on a previous patch that I rejected, causing a build error
here. Sorry about that.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Peter Chen <peter.chen@freescale.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to imx28 needs ARM swp instruction for writing, we set
CI_HDRC_IMX28_WRITE_FIX for imx28.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch makes the controller register map ci_regs_nolpm and ci_regs_lpm as
"const". Further, as all offset fit into a single byte, the type is changed
from uintptr_t to u8.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without this patch a seperate chunk of memory is allocated for the regmap
array. As the regmap is always used it makes no sense to allocate a seperate
memory block for it, this patch moves the regmap array directly into the struct
hw_bank.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This pull request is quite extensive, containing
105 non-merge commits. Because of that, we describe
the changes in sections below:
New drivers:
- Keystone PHY driver and DWC3 Glue Layer
- Aeroflex Gaisler GRUSBDC
- Tahvo PHY driver for N770
- JZ4740 MUSB gluer Layer
- Broadcom PHY Driver
Important new features:
- MUSB DSPS learned about suspend/resume
- New quirk_ep_out_aligned_size flag added to struct usb_gadget
- DWC3 initializes the new quirk flag so gadget drivers can use it.
- AM335x PHY Driver learns about remote wakeup
- Renesas USBHS now requests DMA Engine only once
- s3c-hsotg is now re-used on Broadcom devices
- USB PHY layer now makes sure to initialize the notifier for all
drivers
- omap-control learned about TI's new AM437x devices
- few other usb gadget/function drivers learned about the new
configfs-based binding.
Misc Fixes and Clean Ups:
- Several sparse fixes all over the place
- Removal of redundant of_match_ptr()
- r-car gen2 phy now uses usb_add_phy_dev()
- removal of DEFINE_PCI_DEVICE_TABLE() from a few drivers
- conversion to clk_prepare/clk_unprepare on r8a66597-udc
- some randconfig errors and build warnings were fixed
- removal of unnecessary lock on dwc3-omap.c
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=N4//
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: changes for v3.14 merge window
This pull request is quite extensive, containing
105 non-merge commits. Because of that, we describe
the changes in sections below:
New drivers:
- Keystone PHY driver and DWC3 Glue Layer
- Aeroflex Gaisler GRUSBDC
- Tahvo PHY driver for N770
- JZ4740 MUSB gluer Layer
- Broadcom PHY Driver
Important new features:
- MUSB DSPS learned about suspend/resume
- New quirk_ep_out_aligned_size flag added to struct usb_gadget
- DWC3 initializes the new quirk flag so gadget drivers can use it.
- AM335x PHY Driver learns about remote wakeup
- Renesas USBHS now requests DMA Engine only once
- s3c-hsotg is now re-used on Broadcom devices
- USB PHY layer now makes sure to initialize the notifier for all
drivers
- omap-control learned about TI's new AM437x devices
- few other usb gadget/function drivers learned about the new
configfs-based binding.
Misc Fixes and Clean Ups:
- Several sparse fixes all over the place
- Removal of redundant of_match_ptr()
- r-car gen2 phy now uses usb_add_phy_dev()
- removal of DEFINE_PCI_DEVICE_TABLE() from a few drivers
- conversion to clk_prepare/clk_unprepare on r8a66597-udc
- some randconfig errors and build warnings were fixed
- removal of unnecessary lock on dwc3-omap.c
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQEcBAABAgAGBQJSt1TYAAoJEHm+PkMAQRiGvWgH/iWg8TmEWz4KUKuHthuUi0uh
9+2YDN+4k577Xa0obaG24giQeqkCdxMr3oJrS3FO9jeAmaNRHEGhxUPneisb7RtN
9jIVsz5bPa9/DcK9nqtaUQdvA0O5AWTE6AAPmwleTVy+8CygBo987T2uGELnQCSR
FrKCrMePc7Pj0uthMVXrpJ17Ffm/j7jkfRtPhrxHJyngh3jEux+tPbpynH/aKuO2
47unsSQimoFk7n2SPFvNu3E/vZE2xVbu5SH9MCl5yyiCifFjpi3B71LV/FW51lvm
cK8Jzn2BmYDygRFjnZfq4zJHqYJCBHzpjCLWmR37Dm/JS91aGq3+Cg0stDP8UTs=
=+Hcn
-----END PGP SIGNATURE-----
Merge tag 'v3.13-rc5' into next
Linux 3.13-rc5
* tag 'v3.13-rc5': (231 commits)
Linux 3.13-rc5
aio: clean up and fix aio_setup_ring page mapping
aio/migratepages: make aio migrate pages sane
aio: fix kioctx leak introduced by "aio: Fix a trinity splat"
Don't set the INITRD_COMPRESS environment variable automatically
mm: fix build of split ptlock code
pstore: Don't allow high traffic options on fragile devices
mm: do not allocate page->ptl dynamically, if spinlock_t fits to long
mm: page_alloc: revert NUMA aspect of fair allocation policy
Revert "mm: page_alloc: exclude unreclaimable allocations from zone fairness policy"
mm: Fix NULL pointer dereference in madvise(MADV_WILLNEED) support
qla2xxx: Fix scsi_host leak on qlt_lport_register callback failure
target: Remove extra percpu_ref_init
arm64: ptrace: avoid using HW_BREAKPOINT_EMPTY for disabled events
ARC: Allow conditional multiple inclusion of uapi/asm/unistd.h
target/file: Update hw_max_sectors based on current block_size
iser-target: Move INIT_WORK setup into isert_create_device_ib_res
iscsi-target: Fix incorrect np->np_thread NULL assignment
mm/hugetlb: check for pte NULL pointer in __page_check_address()
fix build with make 3.80
...
Conflicts:
drivers/usb/phy/Kconfig
This patch adds "maxpacket_limit" to struct usb_ep. This field contains
maximum value of maxpacket supported by driver, and is set in driver probe.
This value should be used by autoconfig() function, because value of field
"maxpacket" is set to value from endpoint descriptor when endpoint becomes
enabled. So when autoconfig() function will be called again for this endpoint,
"maxpacket" value will contain wMaxPacketSize from descriptior instead of
maximum packet size for this endpoint.
For this reason this patch adds new field "maxpacket_limit" which contains
value of maximum packet size (which defines maximum endpoint capabilities).
This value is used in ep_matches() function used by autoconfig().
Value of "maxpacket_limit" should be set in UDC driver probe function, using
usb_ep_set_maxpacket_limit() function, defined in gadget.h. This function
set choosen value to both "maxpacket_limit" and "maxpacket" fields.
This patch modifies UDC drivers by adding support for maxpacket_limit.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If we connect Male-A-To-Male-A cable between otg-host and host pc,
the ci->vbus_active is set wrongly, and cause the controller run
at peripheral mode when we load gadget module (ci_udc_start will be run),
but the software runs at host mode due to id = 0. The ehci_irq
can't handle suspend (USBi_SLI) interrupt which is enabled for
peripheral mode, it causes no one will handle irq error.
This patch is needed for 3.12 stable
Cc: stable <stable@vger.kernel.org>
Acked-by: Michael Grzeschik <mgr@pengutronix.de>
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 40ed51a4b (usb: chipidea: host: add vbus regulator
control) introduced a smatch complaint because regulator_disable() is called
without checking whether ci->platdata->reg_vbus is not NULL.
Fix this by adding the check.
This patch is needed for 3.12 stable
Cc: stable <stable@vger.kernel.org>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds i.MX51 as the next user of the usbmisc driver.
Functionality is similar to i.MX53, so at this stage simply
reuse existing i.MX53 calls.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds i.MX27 and i.MX31 as the next user of the usbmisc driver.
Tested-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ci_hdrc_imx's probe needs usbmisc_imx to be loadded beforehand,
so it is better we load usbmisc_imx first.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The regmap only needs to reallocate if the hw_read on the CAP register shows
lpm is used. Therefore the if() statement check the change.
Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't use DEFINE_PCI_DEVICE_TABLE macro, because this macro
is not preferred.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 40ed51a4b (usb: chipidea: host: add vbus regulator
control) introduced a smatch complaint because regulator_disable() is called
without checking whether ci->platdata->reg_vbus is not NULL.
Fix this by adding the check.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull DMA mask updates from Russell King:
"This series cleans up the handling of DMA masks in a lot of drivers,
fixing some bugs as we go.
Some of the more serious errors include:
- drivers which only set their coherent DMA mask if the attempt to
set the streaming mask fails.
- drivers which test for a NULL dma mask pointer, and then set the
dma mask pointer to a location in their module .data section -
which will cause problems if the module is reloaded.
To counter these, I have introduced two helper functions:
- dma_set_mask_and_coherent() takes care of setting both the
streaming and coherent masks at the same time, with the correct
error handling as specified by the API.
- dma_coerce_mask_and_coherent() which resolves the problem of
drivers forcefully setting DMA masks. This is more a marker for
future work to further clean these locations up - the code which
creates the devices really should be initialising these, but to fix
that in one go along with this change could potentially be very
disruptive.
The last thing this series does is prise away some of Linux's addition
to "DMA addresses are physical addresses and RAM always starts at
zero". We have ARM LPAE systems where all system memory is above 4GB
physical, hence having DMA masks interpreted by (eg) the block layers
as describing physical addresses in the range 0..DMAMASK fails on
these platforms. Santosh Shilimkar addresses this in this series; the
patches were copied to the appropriate people multiple times but were
ignored.
Fixing this also gets rid of some ARM weirdness in the setup of the
max*pfn variables, and brings ARM into line with every other Linux
architecture as far as those go"
* 'for-linus-dma-masks' of git://git.linaro.org/people/rmk/linux-arm: (52 commits)
ARM: 7805/1: mm: change max*pfn to include the physical offset of memory
ARM: 7797/1: mmc: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7796/1: scsi: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7795/1: mm: dma-mapping: Add dma_max_pfn(dev) helper function
ARM: 7794/1: block: Rename parameter dma_mask to max_addr for blk_queue_bounce_limit()
ARM: DMA-API: better handing of DMA masks for coherent allocations
ARM: 7857/1: dma: imx-sdma: setup dma mask
DMA-API: firmware/google/gsmi.c: avoid direct access to DMA masks
DMA-API: dcdbas: update DMA mask handing
DMA-API: dma: edma.c: no need to explicitly initialize DMA masks
DMA-API: usb: musb: use platform_device_register_full() to avoid directly messing with dma masks
DMA-API: crypto: remove last references to 'static struct device *dev'
DMA-API: crypto: fix ixp4xx crypto platform device support
DMA-API: others: use dma_set_coherent_mask()
DMA-API: staging: use dma_set_coherent_mask()
DMA-API: usb: use new dma_coerce_mask_and_coherent()
DMA-API: usb: use dma_set_coherent_mask()
DMA-API: parport: parport_pc.c: use dma_coerce_mask_and_coherent()
DMA-API: net: octeon: use dma_coerce_mask_and_coherent()
DMA-API: net: nxp/lpc_eth: use dma_coerce_mask_and_coherent()
...
The correct way for a driver to specify the coherent DMA mask is
not to directly access the field in the struct device, but to use
dma_set_coherent_mask(). Only arch and bus code should access this
member directly.
Convert all direct write accesses to using the correct API.
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If the user chooses peripheral mode for this controller, the vbus
regulator doesn't need to get, since the host will supply the vbus,
it can save one vbus pin for other usage.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Tested-by: Frank Li <frank.li@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Like http://marc.info/?l=linux-usb&m=138200449428874&w=2 said:
two more things are needed to be done:
- If host_start fails, the host_stop should not be called, so we
add check that ci->hcd is not NULL.
- if the host_start fails at the beginning, we need to consider
regulator mismatch issue.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When CMA fails to initialize in v3.12-rc4, the chipidea driver oopses
the kernel while trying to remove and put the HCD which doesn't exist:
WARNING: CPU: 0 PID: 6 at /home/rmk/git/linux-rmk/arch/arm/mm/dma-mapping.c:511
__dma_alloc+0x200/0x240()
coherent pool not initialised!
Modules linked in:
CPU: 0 PID: 6 Comm: kworker/u2:0 Tainted: G W 3.12.0-rc4+ #56
Workqueue: deferwq deferred_probe_work_func
Backtrace:
[<c001218c>] (dump_backtrace+0x0/0x10c) from [<c0012328>] (show_stack+0x18/0x1c)
r6:c05fd9cc r5:000001ff r4:00000000 r3:df86ad00
[<c0012310>] (show_stack+0x0/0x1c) from [<c05f3a4c>] (dump_stack+0x70/0x8c)
[<c05f39dc>] (dump_stack+0x0/0x8c) from [<c00230a8>] (warn_slowpath_common+0x6c/0x8c)
r4:df883a60 r3:df86ad00
[<c002303c>] (warn_slowpath_common+0x0/0x8c) from [<c002316c>] (warn_slowpath_fmt+0x38/0x40)
r8:ffffffff r7:00001000 r6:c083b808 r5:00000000 r4:df2efe80
[<c0023134>] (warn_slowpath_fmt+0x0/0x40) from [<c00196bc>] (__dma_alloc+0x200/0x240)
r3:00000000 r2:c05fda00
[<c00194bc>] (__dma_alloc+0x0/0x240) from [<c001982c>] (arm_dma_alloc+0x88/0xa0)
[<c00197a4>] (arm_dma_alloc+0x0/0xa0) from [<c03e2904>] (ehci_setup+0x1f4/0x438)
[<c03e2710>] (ehci_setup+0x0/0x438) from [<c03cbd60>] (usb_add_hcd+0x18c/0x664)
[<c03cbbd4>] (usb_add_hcd+0x0/0x664) from [<c03e89f4>] (host_start+0xf0/0x180)
[<c03e8904>] (host_start+0x0/0x180) from [<c03e7c34>] (ci_hdrc_probe+0x360/0x670
)
r6:df2ef410 r5:00000000 r4:df2c3010 r3:c03e8904
[<c03e78d4>] (ci_hdrc_probe+0x0/0x670) from [<c0311044>] (platform_drv_probe+0x20/0x24)
[<c0311024>] (platform_drv_probe+0x0/0x24) from [<c030fcac>] (driver_probe_device+0x9c/0x234)
...
---[ end trace c88ccaf3969e8422 ]---
Unable to handle kernel NULL pointer dereference at virtual address 00000028
pgd = c0004000
[00000028] *pgd=00000000
Internal error: Oops: 17 [#1] SMP ARM
Modules linked in:
CPU: 0 PID: 6 Comm: kworker/u2:0 Tainted: G W 3.12.0-rc4+ #56
Workqueue: deferwq deferred_probe_work_func
task: df86ad00 ti: df882000 task.ti: df882000
PC is at usb_remove_hcd+0x10/0x150
LR is at host_stop+0x1c/0x3c
pc : [<c03cacec>] lr : [<c03e88e4>] psr: 60000013
sp : df883b50 ip : df883b78 fp : df883b74
r10: c11f4c54 r9 : c0836450 r8 : df30c400
r7 : fffffff4 r6 : df2ef410 r5 : 00000000 r4 : df2c3010
r3 : 00000000 r2 : 00000000 r1 : df86b0a0 r0 : 00000000
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 10c53c7d Table: 2f29404a DAC: 00000015
Process kworker/u2:0 (pid: 6, stack limit = 0xdf882240)
Stack: (0xdf883b50 to 0xdf884000)
...
Backtrace:
[<c03cacdc>] (usb_remove_hcd+0x0/0x150) from [<c03e88e4>] (host_stop+0x1c/0x3c)
r6:df2ef410 r5:00000000 r4:df2c3010
[<c03e88c8>] (host_stop+0x0/0x3c) from [<c03e8aa0>] (ci_hdrc_host_destroy+0x1c/0x20)
r5:00000000 r4:df2c3010
[<c03e8a84>] (ci_hdrc_host_destroy+0x0/0x20) from [<c03e7c80>] (ci_hdrc_probe+0x3ac/0x670)
[<c03e78d4>] (ci_hdrc_probe+0x0/0x670) from [<c0311044>] (platform_drv_probe+0x20/0x24)
[<c0311024>] (platform_drv_probe+0x0/0x24) from [<c030fcac>] (driver_probe_device+0x9c/0x234)
[<c030fc10>] (driver_probe_device+0x0/0x234) from [<c030ff28>] (__device_attach+0x44/0x48)
...
---[ end trace c88ccaf3969e8423 ]---
Fix this so at least we can continue booting and get to a shell prompt.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Also clean up the last item of the pci id list to be "cleaner".
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This API is used to let the PHY enter/leave low power mode.
Before the controller going to work(at probe/resume), it needs to let
the PHY leave low power mode.
After the controller stopping working(at remove/suspend), it needs to
let the PHY enter low power mode to save power consumption.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the PHY operations are moved to core, delete the related
code at glue layer.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PHY operations are common, so move them to core.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If NO_DMA=y:
drivers/built-in.o: In function `dma_set_coherent_mask':
include/linux/dma-mapping.h:93: undefined reference to `dma_supported'
Reviewed-and-tested-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a pending TD which is not freed after request finishes,
we do this due to a controller bug. This TD needs to be freed when
the driver is removed. It prints below error message when unload
chipidea driver at current code:
"ci_hdrc ci_hdrc.0: dma_pool_destroy ci_hw_td, b0001000 busy"
It indicates the buffer at dma pool are still in use.
This commit will free the pending TD at driver's removal procedure,
it can fix the problem described above.
Acked-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If not, the PHY will be active even the controller is not in use.
We find this issue due to the PHY's clock refcount is not correct
due to -EPROBE_DEFER return after phy's init.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It needs to free ci->hw_bank.regmap explicitly since it is not managed
resource.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Like vbus, the dr_mode and phy_mode are also got from glue layer's
platform data or device node.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The udc-core will call gadget's driver->disconnect, so we should avoid
calling gadget's disconnect again at ci_udc_stop in case the gadget's
unbind free some structs which is still used at gadget's disconnect.
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a pending TD which is not freed after request finishes,
we do this due to a controller bug. This TD needs to be freed when
the driver is removed. It prints below error message when unload
chipidea driver at current code:
"ci_hdrc ci_hdrc.0: dma_pool_destroy ci_hw_td, b0001000 busy"
It indicates the buffer at dma pool are still in use.
This commit will free the pending TD at driver's removal procedure,
it can fix the problem described above.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The chipidea i.MX driver is split into two drivers. The ci_hdrc_imx driver
handles the chipidea cores and the usbmisc_imx driver handles the noncore
registers common to all chipidea cores (but SoC specific). Current flow is:
- usbmisc sets an ops pointer in the ci_hdrc_imx driver during probe
- ci_hdrc_imx checks if the pointer is valid during probe, if yes calls
the functions in the ops pointer.
- usbmisc_imx calls back into the ci_hdrc_imx driver to get additional
data
This is overly complicated and has problems if the drivers are compiled
as modules. In this case the usbmisc_imx driver can be unloaded even if
the ci_hdrc_imx driver still needs usbmisc functionality.
This patch changes this by letting the ci_hdrc_imx driver calling functions
from the usbmisc_imx driver. This way the symbol resolving during module
load makes sure the ci_hdrc_imx driver depends on the usbmisc_imx driver.
Also instead of letting the usbmisc_imx driver call back into the ci_hdrc_imx
driver, pass the needed data in the first place.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For chipidea, the IP must know vbus before the controller
begins to run. So the .pullup should only be called when
the vbus is there.
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the controller only runs when the ci->vbus_active is true.
So the flag CI_HDRC_PULLUP_ON_VBUS is useless no longer.
If the user doesn't have otgsc, he/she needs to change ci_handle_vbus_change
to update ci->vbus_active.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
