Use devm_spi_register_master() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use devm_spi_register_master() to make cleanup paths simpler,
and remove a duplicate put.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use devm_spi_register_master() to make cleanup paths simpler,
and remove a duplicate put.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
If pci_iomap() returns NULL, adding "PCH_ADDRESS_SIZE * plat_dev->id"
can make it non-NULL which breaks the error handling.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Calling kfree() to clean up the memory obtained from spi_alloc_master() is
wrong as this is done in spi_master_release() when spi_master->dev's refcount
reaches zero.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add compatibles for s3c6410, s5pc100 and s5pc110/s5pv210 boards.
Signed-off-by: Mateusz Krawczuk <m.krawczuk@partner.samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Also improve the error reporting on failure and remove a duplicate put.
This provides a small code saving.
Signed-off-by: Mark Brown <broonie@linaro.org>
This call is needed to cleanup the resources requested by
spi_bitbang_start in the probe callback.
Noticed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Many drivers that use bitbang library have a leak on probe error paths.
This is because once a spi_master_get() call succeeds, we need an additional
spi_master_put() call to free the memory.
Fix this issue by moving the code taking a reference to master to
spi_bitbang_start(), so spi_bitbang_start() will take a reference to master on
success. With this change, the caller is responsible for calling
spi_bitbang_stop() to decrement the reference and spi_master_put() as
counterpart of spi_alloc_master() to prevent a memory leak.
So now we have below patten for drivers using bitbang library:
probe:
spi_alloc_master -> Init reference count to 1
spi_bitbang_start -> Increment reference count
remove:
spi_bitbang_stop -> Decrement reference count
spi_master_put -> Decrement reference count (reference count reaches 0)
Fixup all users accordingly.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Suggested-by: Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
Acked-by: Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Help simplify the cleanup code for SPI master drivers by providing a
managed master registration function, ensuring that the master is
automatically unregistered whenever the device is unbound.
Signed-off-by: Mark Brown <broonie@linaro.org>
subsys_init_call() initializes driver too early.
It's preventing to move DMA channel allocation at the begining
(driver probe).
This patch reduces and simplifies initalization code by
using module_platform_driver() macro.
It's also efficiently delaying driver startup.
Signed-off-by: Lukasz Czerwinski <l.czerwinski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
's3c24xx_spi_tryfiq' is used only in this file. Make it static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The R8A7790 has QSPI module which is very similar to RSPI.
This patch adds into RSPI module together to supports QSPI module.
Signed-off-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Mark Brown <broonie@linaro.org>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
'break' immediately after return has no effect.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
- improve dependencies using COMPILE_TEST
- fix a typo
- drop platform_set_drvdata(pdev, NULL) in error path of probe
- make MODULE_LICENSE match the header
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Free_irq is not needed if there has been no request_irq. Free_irq is
removed from both the probe and remove functions. The correct request_irq
and free_irq appear to be in the add_host and remove_host functions in
spi-dw.c.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e;
@@
*e = platform_get_irq(...);
... when != request_irq(e,...)
*free_irq(e,...)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@linaro.org>
'prescale' contains the return value of davinci_spi_get_prescale()
which is a signed integer. Convert 'prescale' to integer to silence
the following warning:
drivers/spi/spi-davinci.c:318 davinci_spi_setup_transfer() warn:
unsigned 'prescale' is never less than zero.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Instead of using legacy suspend/resume methods, using newer
dev_pm_ops structure allows better control over power management.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Instead of using legacy suspend/resume methods, using newer
dev_pm_ops structure allows better control over power management.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fixes the following types of checkpatch errors and warning:
ERROR: space required after that ',' (ctx:VxV)
WARNING: sizeof *as should be sizeof(*as)
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Instead of using legacy suspend/resume methods, using newer
dev_pm_ops structure allows better control over power management.
Also, duplicated 'return' is removed from atmel_spi_resume().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In case of error, the function devm_ioremap_resource() returns
ERR_PTR() and never returns NULL. The NULL test in the return
value check should be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mark Brown <broonie@linaro.org>
Calling kfree() to clean up the memory obtained from spi_alloc_master() is
wrong as this is done in spi_master_release() when spi_master->dev's refcount
reaches zero.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Device tree and bindings updates for 3.12.
General additions of various on-chip and on-board peripherals on various
platforms as support gets added. Some of the bigger changes are:
- Addition of (new) PCI-e support on Tegra.
- More Tegra4 support, including PMC configuration for Dalmore.
- Addition of a new board for Exynos4 (trats2) and more bindings for 4x12 IP.
- Addition of Allwinner A20 and A31 SoC and board files.
- Move of the ST Ericsson device tree files to now use ste-* prefix.
- More move of hardware description of shmobile platforms to DT.
- Two new board dts files for Freescale MXs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=1GuI
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Olof Johansson:
"Device tree and bindings updates for 3.12.
General additions of various on-chip and on-board peripherals on
various platforms as support gets added. Some of the bigger changes
are:
- Addition of (new) PCI-e support on Tegra.
- More Tegra4 support, including PMC configuration for Dalmore.
- Addition of a new board for Exynos4 (trats2) and more bindings for
4x12 IP.
- Addition of Allwinner A20 and A31 SoC and board files.
- Move of the ST Ericsson device tree files to now use ste-* prefix.
- More move of hardware description of shmobile platforms to DT.
- Two new board dts files for Freescale MXs"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (177 commits)
dts: Rename DW APB timer compatible strings
dts: Deprecate ALTR as a vendor prefix
of: add vendor prefix for Altera Corp.
ARM: at91/dt: sam9x5ek: add sound configuration
ARM: at91/dt: sam9x5ek: enable SSC
ARM: at91/dt: sam9x5ek: add WM8731 codec
ARM: at91/dt: sam9x5: add SSC DMA parameters
ARM: at91/dt: add at91rm9200 PQFP package version
ARM: at91: at91rm9200: set default mmc0 pinctrl-names
ARM: at91: at91sam9n12: correct pin number of gpio-key
ARM: at91: at91sam9n12: add qt1070 support
ARM: at91: at91sam9n12: add pinctrl of TWI
ARM: at91: Add PMU support for sama5d3
ARM: at91: at91sam9260: add missing pinctrl-names on mmc
ARM: tegra: configure power off for Dalmore
ARM: DT: binding fixup to align with vendor-prefixes.txt (DT)
ARM: dts: add sdio blocks to bcm28155-ap board
ARM: dts: align sdio numbers to HW definition
ARM: sun7i: Add Olimex A20-Olinuxino-Micro support
ARM: sun7i: Add Allwinner A20 DTSI
...
Pull trivial tree from Jiri Kosina:
"The usual trivial updates all over the tree -- mostly typo fixes and
documentation updates"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (52 commits)
doc: Documentation/cputopology.txt fix typo
treewide: Convert retrun typos to return
Fix comment typo for init_cma_reserved_pageblock
Documentation/trace: Correcting and extending tracepoint documentation
mm/hotplug: fix a typo in Documentation/memory-hotplug.txt
power: Documentation: Update s2ram link
doc: fix a typo in Documentation/00-INDEX
Documentation/printk-formats.txt: No casts needed for u64/s64
doc: Fix typo "is is" in Documentations
treewide: Fix printks with 0x%#
zram: doc fixes
Documentation/kmemcheck: update kmemcheck documentation
doc: documentation/hwspinlock.txt fix typo
PM / Hibernate: add section for resume options
doc: filesystems : Fix typo in Documentations/filesystems
scsi/megaraid fixed several typos in comments
ppc: init_32: Fix error typo "CONFIG_START_KERNEL"
treewide: Add __GFP_NOWARN to k.alloc calls with v.alloc fallbacks
page_isolation: Fix a comment typo in test_pages_isolated()
doc: fix a typo about irq affinity
...
up with PTR_ERR_OR_ZERO(), and replacing or fixing all the usages.
This has been sitting in linux-next for a whole cycle.
Thanks,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJSJo+1AAoJENkgDmzRrbjxIC4QALJK95o8AUXuwUkl+2fmFkUt
hh2/PJ1vDYgk4Xt0J6hyoK7XMa0H1RkbBrROuDdsBnorMFpEsGcgdkUZte9ufoAS
97Bg+7N0KPbTB/S8vOwtW1vbERTJIVPN2uf6h1Wqm9Xc2puCh3HbMMr1AWMGu0WQ
NqY5+Zz8zecy1UOrMhEP6H1CjeQcL1w1DO6YM5ydeqlKNzAz+JMfDXriLPDwiE7+
XFPDF/O3Vtd2ckA7L70Lio7hfHwxV5U4WwFVfiwls98XB4jcZqDKIoh1r8z4SRgR
+0Rae2DN3BaOabGMr//5XdrzQVpwJTh5m2w8BAOHJvCJ9HR7Sq29UIN4u+TowZBy
L2xYo4dvFxkympwu5zEd3c7vHYWKIaqmSq5PIjr4gF/uIo2OeOTrpPIK782ZEYb7
e+qUgOEM05V9AmQZCrSZeP9u474Sj8ow3sCtWxfdRtwNfoEIcUXsNNJd/zDHlVtW
cEtXqc2xXIpcuUJQWlSaGp8fmRQjVZPzrLKYLM2m39ZcOOJbf5rzQAYS7hHPosIa
SK+YVux/+Zzi+Xo/vXq1OlM/SruCr5S7JOgCxLowoQ88vupgXME6uPyC8EO+QQ50
GsrHes5ZNLbk0uVsfcexIyojkUnyvDmmnDpv+1zdC6RgZLJQn8OXp5yNhHhnhrFT
BiHX6YFWtDDqRlVv8Q0F
=LeaW
-----END PGP SIGNATURE-----
Merge tag 'PTR_RET-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull PTR_RET() removal patches from Rusty Russell:
"PTR_RET() is a weird name, and led to some confusing usage. We ended
up with PTR_ERR_OR_ZERO(), and replacing or fixing all the usages.
This has been sitting in linux-next for a whole cycle"
[ There are still some PTR_RET users scattered about, with some of them
possibly being new, but most of them existing in Rusty's tree too. We
have that
#define PTR_RET(p) PTR_ERR_OR_ZERO(p)
thing in <linux/err.h>, so they continue to work for now - Linus ]
* tag 'PTR_RET-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
GFS2: Replace PTR_RET with PTR_ERR_OR_ZERO
Btrfs: volume: Replace PTR_RET with PTR_ERR_OR_ZERO
drm/cma: Replace PTR_RET with PTR_ERR_OR_ZERO
sh_veu: Replace PTR_RET with PTR_ERR_OR_ZERO
dma-buf: Replace PTR_RET with PTR_ERR_OR_ZERO
drivers/rtc: Replace PTR_RET with PTR_ERR_OR_ZERO
mm/oom_kill: remove weird use of ERR_PTR()/PTR_ERR().
staging/zcache: don't use PTR_RET().
remoteproc: don't use PTR_RET().
pinctrl: don't use PTR_RET().
acpi: Replace weird use of PTR_RET.
s390: Replace weird use of PTR_RET.
PTR_RET is now PTR_ERR_OR_ZERO(): Replace most.
PTR_RET is now PTR_ERR_OR_ZERO
The current interrupt handler calls pm_runtime_suspended() to check if the
device is suspended or not. However, runtime PM status of the device is
only set to suspended once all PM runtime suspend hooks have executed.
In case of Intel Lynxpoint we have the device bound to the ACPI power
domain and its runtime suspend hook will put the device to D3hot (or D3cold
if possible). This means that the device is powered off before its state is
set to runtime suspended. While in this state the device might get an
interrupt that is meant for another device (as the interrupt line is
shared), and because the device is powered off accessing its registers will
return 0xffffffff that the driver misinterprets as an invalid state.
When this happens user will see messages like below on the console:
pxa2xx-spi INT33C0:00: bad message state in interrupt handler
Fix this by checking the status register for ~0 and returning IRQ_NONE in
that case.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add the missing unlock before return from function ti_qspi_start_transfer_one()
in the error handling case.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mark Brown <broonie@linaro.org>
spi: quad: fix the name of DT property in patch
The previous property name spi-tx-nbits and spi-rx-nbits looks not
human-readable. To make it consistent with other devices, using property
name spi-tx-bus-width and spi-rx-bus-width instead of the previous one
specify the number of data wires that spi controller will work in.
Add the specification in spi-bus.txt.
Signed-off-by: wangyuhang <wangyuhang2014@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In the case spi_master_initialize_queue() fails, current code calls
device_unregister() before return error from spi_register_master().
However, all the drivers call spi_master_put() in the error path if
spi_register_master() fails. Thus we should call device_del() rather than
device_unregister() before return error from spi_register_master().
This also makes all the spi_register_master() error handling consistent,
because all other error paths of spi_register_master() expect drivers to
call spi_master_put() if spi_register_master() fails.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Obviously the of_device_id table name is wrong.
Fix below build error:
CC [M] drivers/spi/spi-efm32.o
drivers/spi/spi-efm32.c:499:1: error: '__mod_of_device_table' aliased to undefined symbol 'efm32_uart_dt_ids'
make[2]: *** [drivers/spi/spi-efm32.o] Error 1
make[1]: *** [drivers/spi] Error 2
make: *** [drivers] Error 2
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The Altera SPI hardware can be configured to support data width from 1 to 32
since Quartus II 8.1. To avoid truncation by integer division, use DIV_ROUND_UP
to calculate hw->bytes_per_word.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Mark Brown <broonie@linaro.org>
In rspi_remove(), current code dereferences rspi after spi_unregister_master(),
thus add an extra spi_master_get() call is necessary to prevent use after free.
Current code already has an extra spi_master_put() call in rspi_remove(), so
this patch just adds a spi_master_get() call rather than a spi_master_get() with
spi_master_put() calls.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The addition SPI quad support made the DT properties mandatory, breaking
compatibility with existing systems. Fix that by making them optional,
also improving the error messages while we're at it.
Signed-off-by: Mark Brown <broonie@linaro.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
Delete a "return" when commit the patch to a new kernel version
by mistake. So recover it.
Signed-off-by: wangyuhang <wangyuhang2014@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Because most of the vendor prefixes are lower case, deprecate
the vendor prefix "ALTR" in place of "altr" for Altera Corp..
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
Use dev_get_drvdata() instead of platform_get_drvdata(to_platform_device(dev)).
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The code in nuc900_slave_select() supports handling SPI_CS_HIGH.
Thus set SPI_CS_HIGH bit in master->mode_bits to make it work.
Otherwise, spi_setup() will return unsupported mode bits error message if
SPI_CS_HIGH is set in the mode field of struct spi_device.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Convert the composition of devm_request_mem_region and devm_ioremap to a
single call to devm_ioremap_resource. The associated call to
platform_get_resource is also simplified and moved next to the new call to
devm_ioremap_resource.
This was done using a combination of the semantic patches
devm_ioremap_resource.cocci and devm_request_and_ioremap.cocci, found in
the scripts/coccinelle/api directory.
This patch also removes the label exit_busy, to use the error code returned
by the failing operation, rather than always -EBUSY.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch simplifies the code and makes it better in readability.
Now the logic in the while loop is simply
"write to ALTERA_SPI_TXDATA then read from ALTERA_SPI_TXDATA".
There is a slightly logic change because now we avoid a read-write cycle when
hw->len is 0. Since the code in bitbang library will call bitbang->txrx_bufs()
only when t->len is not 0, this is not a problem.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix module device table entry. Without this, there will
be a build failure while trying to build qspi as a module.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
the unit of len of spi_transfer is in bytes, not in spi words. the
old codes misunderstood that and thought the len is the amount of
spi words. but it is actually how many bytes existing in the spi
buffer.
this patch fixes that and also rename left_tx_cnt and left_rx_cnt
to left_tx_word and left_rx_word to highlight they are in words.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Support for multiple lines in SPI framework has been picked[1].
[1]: http://comments.gmane.org/gmane.linux.kernel.spi.devel/14420
Hence, adapting ti qspi driver to support multiple data lines for read.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mark Brown <broonie@linaro.org>
The call to spi_unregister_master results in device memory being freed, it must
no longer be accessed afterwards. Thus call spi_master_get() to get an extra
reference to the device and call spi_master_put() only after the last access to
device data.
Note, current code has an extra spi_master_put() call in bcm2835_spi_remove().
Thus this patch just adds an spi_master_get() to balance the reference count.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
We have tested master->running immediately after grab the master->queue_lock.
The status of master->running won't be changed until we release the lock.
Thus remove a redundant test for master->running.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is a bug in the following patch:
http://comments.gmane.org/gmane.linux.kernel.spi.devel/14420
spi: DUAL and QUAD support
fix the previous patch some mistake below:
1. DT in slave node, use "spi-tx-nbits = <1/2/4>" in place of using
"spi-tx-dual, spi-tx-quad" directly, same to rx. So correct the
previous way to get the property in @of_register_spi_devices().
2. Change the value of transfer bit macro(SPI_NBITS_SINGLE, SPI_NBITS_DUAL
SPI_NBITS_QUAD) to 0x01, 0x02 and 0x04 to match the actual wires.
3. Add the following check
(1)keep the tx_nbits and rx_nbits in spi_transfer is not beyond the
single, dual and quad.
(2)keep tx_nbits and rx_nbits are contained by @spi_device->mode
example: if @spi_device->mode = DUAL, then tx/rx_nbits can not be set
to QUAD(SPI_NBITS_QUAD)
(3)if "@spi_device->mode & SPI_3WIRE", then tx/rx_nbits should be in
single(SPI_NBITS_SINGLE)
Checking of the tx/rx transfer bits and mode bits should be done conditionally
based on type of buffer filled else EINVAL condition will
always get hit either for rx or tx.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
fix the previous patch some mistake below:
1. DT in slave node, use "spi-tx-nbits = <1/2/4>" in place of using
"spi-tx-dual, spi-tx-quad" directly, same to rx. So correct the
previous way to get the property in @of_register_spi_devices().
2. Change the value of transfer bit macro(SPI_NBITS_SINGLE, SPI_NBITS_DUAL
SPI_NBITS_QUAD) to 0x01, 0x02 and 0x04 to match the actual wires.
3. Add the following check
(1)keep the tx_nbits and rx_nbits in spi_transfer is not beyond the
single, dual and quad.
(2)keep tx_nbits and rx_nbits are contained by @spi_device->mode
example: if @spi_device->mode = DUAL, then tx/rx_nbits can not be set
to QUAD(SPI_NBITS_QUAD)
(3)if "@spi_device->mode & SPI_3WIRE", then tx/rx_nbits should be in
single(SPI_NBITS_SINGLE)
Signed-off-by: wangyuhang <wangyuhang2014@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The patch add basic support for the quad spi controller.
QSPI is a kind of spi module that allows single,
dual and quad read access to external spi devices. The module
has a memory mapped interface which provide direct interface
for accessing data form external spi devices.
The patch will configure controller clocks, device control
register and for defining low level transfer apis which
will be used by the spi framework to transfer data to
the slave spi device(flash in this case).
Test details:
-------------
Tested this on dra7 board.
Test1: Ran mtd_stesstest for 40000 iterations.
- All iterations went through without failure.
Test2: Use mtd utilities:
- flash_erase to erase the flash device
- mtd_debug read to read data back.
- mtd_debug write to write to the data flash.
diff between the write and read data shows zero.
Acked-by: Felipe Balbi<balbi@ti.com>
Reviewed-by: Felipe Balbi<balbi@ti.com>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mark Brown <broonie@linaro.org>
The serial peripheral interface (SPI) module implemented on Freescale Vybrid
platform provides a synchronous serial bus for communication between Vybrid
and the external peripheral device.
The SPI supports full-duplex, three-wire synchronous transfer, has TX/RX FIFO
with depth of four entries.
This driver is the SPI master mode driver and has been tested on Vybrid
VF610TWR board.
Signed-off-by: Alison Wang <b18965@freescale.com>
Signed-off-by: Chao Fu <b44548@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
cleanup the MPC512x SoC's SPI master's use of the clock API
- get, prepare, and enable the MCLK during probe; disable, unprepare and
put the MCLK upon remove; hold a reference to the clock over the
period of use
- fetch MCLK rate (reference) once during probe and slightly reword BCLK
(bitrate) determination to reduce redundancy as well as to not exceed
the maximum text line length
- stick with the PPC_CLOCK 'psc%d_mclk' name for clock lookup, only
switch to a fixed string later after device tree based clock lookup
will have become available
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
When CONFIG_ARM_LPAE=y the following build warning is generated:
drivers/spi/spi-pl022.c:2178:9: warning: format '%x' expects argument of type 'unsigned int', but argument 2 has type 'resource_size_t' [-Wformat]
According to Documentation/printk-formats.txt '%pa' can be used to properly
print 'resource_size_t'.
Reported-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Check of 'r' and calls to dev_err are already done in devm_ioremap_resource,
so no need to do them twice.
Signed-off-by: Laurent Navet <laurent.navet@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since commit 543bb25 "spi: add ability to validate xfer->bits_per_word in SPI
core", the driver can set bits_per_word_mask for the master then the SPI core
will reject transfers that attempt to use an unsupported bits_per_word value.
So we can remove octeon_spi_validate_bpw() and let SPI core handle the checking.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Both prepare_transfer_hardware and unprepare_transfer_hardware callbacks are
optional, so we don't need to implement an empty function for them.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since the 'spi: Support transfer speed checking in the core'
change, the SPI core validates the desired speed of a given
transfer against the minimum and maximum speeds supported by
the controller.
If the speed of a transfer is not specified, the core uses
the maximum speed of the actual SPI device. However if the
maximum speed of the actual device is greater than the
maximum speed of the controller, the core will reject the
transfer due to the aforementioned change.
Change the code to use the maximum speed of the controller
by default if that is below the device's maximum speed.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Remove unneeded error handling on the result of a call to
platform_get_resource when the value is passed to devm_ioremap_resource.
Move the call to platform_get_resource adjacent to the call to
devm_ioremap_resource to make the connection between them more clear.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression pdev,res,n,e,e1;
expression ret != 0;
identifier l;
@@
- res = platform_get_resource(pdev, IORESOURCE_MEM, n);
... when != res
- if (res == NULL) { ... \(goto l;\|return ret;\) }
... when != res
+ res = platform_get_resource(pdev, IORESOURCE_MEM, n);
e = devm_ioremap_resource(e1, res);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Remove unneeded error handling on the result of a call to
platform_get_resource when the value is passed to devm_ioremap_resource.
Move the call to platform_get_resource adjacent to the call to
devm_ioremap_resource to make the connection between them more clear.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression pdev,res,n,e,e1;
expression ret != 0;
identifier l;
@@
- res = platform_get_resource(pdev, IORESOURCE_MEM, n);
... when != res
- if (res == NULL) { ... \(goto l;\|return ret;\) }
... when != res
+ res = platform_get_resource(pdev, IORESOURCE_MEM, n);
e = devm_ioremap_resource(e1, res);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@linaro.org>
We always need the device to be runtime PM enabled to use it so just skip
the DMA initialisation not the entire prepare when polling.
Signed-off-by: Mark Brown <broonie@linaro.org>
Since the driver supports only contiguous buffers, there is no need to
manually construct a scatterlist with just a single entry, when there is
a dedicated helper for this purpose.
This patch modifies prepare_dma() function to use available helper instead
of manually creating a scatterlist.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Comments in linux/spi/spi.h and observed behavior show that .setup()
callback can be called multiple times without corresponding calls to
.cleanup(), what was incorrectly assumed by spi-s3c64xx driver, leading
to failures trying to request CS GPIO multiple times.
This patch modifies the behavior of spi-s3c64xx driver to request CS
GPIO only on first call to .setup() after last .cleanup().
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Not all fields of dma_slave_config struct are being initialized by
prepare_dma() function, leaving those which are not in undefined state,
which can confuse DMA drivers using them.
This patch adds call to memset() to zero the struct before initializing
a subset of its fields.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Now that the bitbang core does not require a setup() function we can
drop the check in the altera, nuc900 and xilinx drivers.
Signed-off-by: Mark Brown <broonie@linaro.org>
It's perfectly valid not to have a setup callback when the probe routine
does all the needed things. So don't even check for this case and trust
the caller.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The bits_per_word variable is not used after commit 24778be20f
"spi: convert drivers to use bits_per_word_mask".
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Now that DMA support has been added to the driver it needs the
architecture DMA driver to be built in order to link.
Signed-off-by: Mark Brown <broonie@linaro.org>
this patch enables DMA support for SiRFSoC SPI driver, if both
buffers and length are aligned with DMA controller's hardware
limitation, use generic SiRF generic dmaengine driver.
for PIO, SiRF SPI controller actually is using rx to trigger rx,
that means if we write any word to tx fifo, we will get a word
from rx fifo. for DMA, we use two different channel for tx and
rx, and issue them both for every transfer.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Pass master to platform_set_drvdata() then we can remove my_master pointer.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
We have a SPI_BPW_MASK macro defined in spi.h, use it instead of open-coded.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Don't rely on shdma dhaengine driver getting DMA slave addresses from its
slave configuration. Instead provide those addresses, using a
dmaengine_slave_config() call.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch fixes the following sparse warning by changing the
the format specifier for size_t to %zu.
drivers/spi/spi-ep93xx.c:512:3: warning:
format ‘%d’ expects argument of type ‘int’,
but argument 3 has type ‘size_t’ [-Wformat]
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch fixes the following sparse warnings.
dma_addr_t can be either u32 or u64 so we should cast to the
largest type and use the format specifier %llx.
drivers/spi/spi-atmel.c: In function ‘atmel_spi_next_xfer_dma_submit’:
drivers/spi/spi-atmel.c:631:2: warning:
format ‘%x’ expects argument of type ‘unsigned int’,
but argument 7 has type ‘dma_addr_t’ [-Wformat]
drivers/spi/spi-atmel.c:631:2: warning:
format ‘%x’ expects argument of type ‘unsigned int’,
but argument 9 has type ‘dma_addr_t’ [-Wformat]
drivers/spi/spi-atmel.c: In function ‘atmel_spi_pdc_next_xfer’:
drivers/spi/spi-atmel.c:734:3: warning:
format ‘%x’ expects argument of type ‘unsigned int’,
but argument 7 has type ‘dma_addr_t’ [-Wformat]
drivers/spi/spi-atmel.c:734:3: warning:
format ‘%x’ expects argument of type ‘unsigned int’,
but argument 9 has type ‘dma_addr_t’ [-Wformat]
drivers/spi/spi-atmel.c:773:3: warning:
format ‘%x’ expects argument of type ‘unsigned int’,
but argument 7 has type ‘dma_addr_t’ [-Wformat]
drivers/spi/spi-atmel.c:773:3: warning:
format ‘%x’ expects argument of type ‘unsigned int’,
but argument 9 has type ‘dma_addr_t’ [-Wformat]
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Commit 048177ce3b (spi: spi-davinci:
convert to DMA engine API) introduced a regression: dma_map_single()
is called with direction DMA_FROM_DEVICE for rx and for tx.
Signed-off-by: Christian Eggers <ceggers@gmx.de>
Acked-by: Matt Porter <mporter@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org # v3.7.x+
Most SPI drivers that implement runtime PM support use identical code to
do so: they acquire a runtime PM lock in prepare_transfer_hardware() and
then they release it in unprepare_transfer_hardware(). The variations in
this are mostly missing error checking and the choice to use autosuspend.
Since these runtime PM calls are normally the only thing in the prepare
and unprepare callbacks and the autosuspend API transparently does the
right thing on devices with autosuspend disabled factor all of this out
into the core with a flag to enable the behaviour.
Signed-off-by: Mark Brown <broonie@linaro.org>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Currently the tegra slink driver acquires a runtime PM reference for the
duration of each transfer. This may result in the IP being powered down
between transfers which would be at best wasteful. Instead it is better
to do this in the callbacks that are generated before and after starting
a series of transfers, keeping the IP powered throughout.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Currently the tegra sflash driver acquires a runtime PM reference for the
duration of each transfer. This may result in the IP being powered down
between transfers which would be at best wasteful. Instead it is better
to do this in the callbacks that are generated before and after starting
a series of transfers, keeping the IP powered throughout.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Currently the tegra114 driver acquires a runtime PM reference for the
duration of each transfer. This may result in the IP being powered down
between transfers which would be at best wasteful. Instead it is better
to do this in the callbacks that are generated before and after starting
a series of transfers, keeping the IP powered throughout.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Enable auto loading by udev when spi-imx is compiled as a module.
Signed-off-by: Niels de Vos <ndevos@redhat.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Enable the build of drivers which don't have any real build time
dependency on their architecture or platform with COMPILE_TEST,
providing better build time coverage.
Signed-off-by: Mark Brown <broonie@linaro.org>
Previously the runtime PM API insisted on having callbacks for everything
but this requirement was removed a while ago so the empty callbacks can
also be removed.
Signed-off-by: Mark Brown <broonie@linaro.org>
Keystone2 SOCs share the SPI IP block with DaVinci based SOCs. Update
the config bits so that its usable on Keystone2 based SOCs.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
sdd->ops->request is unsigned int, not unsigned long.
Also, sdd->rx_dma.ch is a 'struct dma_chan *'.
Thus, (void *) is converted to (struct dma_chan *)(unsigned long),
in order to fix possible sparse warnings.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix the following build warnings when LPAE is enabled:
drivers/spi/spi-s3c64xx.c:1466:2: warning: format '%x' expects argument of type 'unsigned int', but argument 4 has type
'resource_size_t' [-Wformat]
drivers/spi/spi-s3c64xx.c:1466:2: warning: format '%x' expects argument of type 'unsigned int', but argument 5 has type
'resource_size_t' [-Wformat]
Use vsprintf extension %pR to format resource.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix the following checkpatch error and warnings:
ERROR: "(foo*)" should be "(foo *)"
WARNING: line over 80 characters
WARNING: quoted string split across lines
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since the driver has been converted to use the core message pump code
the only use of the messsage queue in the driver is a check to see if
it is empty which will always succeed since nothing ever adds to the
queue. Just remove the queue.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
As devm_ioremap_resource() is used on probe, there is no need to explicitly
check the return value from platform_get_resource(), as this is something that
devm_ioremap_resource() takes care by itself.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make spi core calculate the message length while
populating the other transfer parameters.
Usecase, driver can use it to populate framelength filed in their
controller.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since commit 2025172e3 (spi/bitbang: Use core message pump), the following
kernel crash is seen:
Unable to handle kernel NULL pointer dereference at virtual address 0000000d
pgd = 80004000
[0000000d] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
Modules linked in:
CPU: 1 PID: 48 Comm: spi32766 Not tainted 3.11.0-rc1+ #4
task: bfa3e580 ti: bfb90000 task.ti: bfb90000
PC is at spi_bitbang_transfer_one+0x50/0x248
LR is at spi_bitbang_transfer_one+0x20/0x248
...
,and also the following build warning:
drivers/spi/spi-bitbang.c: In function 'spi_bitbang_start':
drivers/spi/spi-bitbang.c:436:31: warning: assignment from incompatible pointer type [enabled by default]
In order to fix it, we need to change the first parameter of
spi_bitbang_transfer_one() to 'struct spi_master *master'.
Tested on a mx6qsabrelite by succesfully probing a SPI NOR flash.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In xilinx_spi_probe() we use xspi->irq to store negative error codes so
it has to be signed. We weren't going to use the upper bit any way so
this is fine.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Convert drivers using bitbang to use the core mesasge pump infrastructure,
saving some code and meaning that these drivers get to take advantage of
work done on improving the core implementation.
Signed-off-by: Mark Brown <broonie@linaro.org>
The SPI core provides infrastructure for standard message queueing. Use
that instead of handling it in the driver.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Mark Brown <broonie@linaro.org>
Replace clk_enable/disable with clk_prepare_enable/disable_unprepare to
avoid common clk framework warnings.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use devm_request_irq() for irq allocation which
simplify driver code.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
devm_ioremap_resource() automatically checks that
struct resource is initialized.
Also group platform_get_resource() and devm_ioremap_resource()
together.
And remove mem resource from struct xilinx_spi.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This is a more traditional name and makes things a bit clearer when
referring to actual struct devices as we do frequently during probe().
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
In the past there used to be a separate platform device type for device
tree systems so the probe and removal functions were split into generic
and bus sections. Since this is no longer the case simplify the code (and
remove some unprototyped exports) by factoring everything into the bus
probe() and remove().
Signed-off-by: Mark Brown <broonie@linaro.org>
We have nice specifier in kernel for that.
It changes separator from ',' (comma) to space, though it's not a big deal
since it's just a debug message.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mark Brown <broonie@linaro.org>
Missing this will cause some user cases fail when they want to change spi
transfer mode.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Due to changes in mainline prior to submission the spi device detection
in polling mode breaks. This revealed the missing check for polling
during dma prepare. This patch adds the missing check.
Signed-off-by: Girish K S <ks.giri@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is an additional bit in the Intel LPSS SPI private registers that
needs to be set in order to be able to use DMA with the SPI controller.
Enable this as well.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
stmp_reset_block() may fail, so let's check its return value and propagate it in
the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
clk_prepare_enable() may fail, so let's check its return value and propagate it
in the case of error.
While at it, rename 'out_free_dma' to 'out_disable_clk' so that it can properly
describe its purpose.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
On mxs_spi_probe() the dma channels are requested prior to enabling the SSP
clock, so in the error path we should disable the SSP clock first and
release the DMA channels later.
Same logic applies in mxs_spi_remove().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
clk_prepare_enable() may fail, so let's check its return value and propagate it
in the case of error.
While at it, fix the order of clk_disable_unprepare calls: clk_ipg should be
disabled first, followed by clk_per.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Using devm functions can make the code smaller and cleaner.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The divider values stored in the per chip data are only used to set the
registers in the hardware to generate the desired SPI clock. Since these
are calculated per transfer based on the t->speed_hz there is no reason
keep them in the per chip data.
Move the ep93xx_spi_calc_divisors() call into ep93xx_spi_chip_setup()
and return the dividers thru pointers. Remove the divider values from
the per chip data structure.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Mark Brown <broonie@linaro.org>
The divisors needed to generate the SPI clock are calculated per
transfer based on the t->speed_hz. There is no reason to calculate
them in ep93xx_spi_setup().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use devm_clk_get() so that the clk_put() happens automatically when
the last reference to this driver is dropped.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Mark Brown <broonie@linaro.org>
