ENETC implement time specific departure capability, which enables
the user to specify when a frame can be transmitted. When this
capability is enabled, the device will delay the transmission of
the frame so that it can be transmitted at the precisely specified time.
The delay departure time up to 0.5 seconds in the future. If the
departure time in the transmit BD has not yet been reached, based
on the current time, the packet will not be transmitted.
This driver was loaded by Qos driver ETF. User could load it by tc
commands. Here are the example commands:
tc qdisc add dev eth0 root handle 1: mqprio \
num_tc 8 map 0 1 2 3 4 5 6 7 hw 1
tc qdisc replace dev eth0 parent 1:8 etf \
clockid CLOCK_TAI delta 30000 offload
These example try to set queue mapping first and then set queue 7
with 30us ahead dequeue time.
Then user send test frame should set SO_TXTIME feature for socket.
There are also some limitations for this feature in hardware:
- Transmit checksum offloads and time specific departure operation
are mutually exclusive.
- Time Aware Shaper feature (Qbv) offload and time specific departure
operation are mutually exclusive.
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use resource_size rather than a verbose computation on
the end and start fields.
The semantic patch that makes these changes is as follows:
(http://coccinelle.lip6.fr/)
<smpl>
@@ struct resource ptr; @@
- (ptr.end + 1 - ptr.start)
+ resource_size(&ptr)
@@ struct resource *ptr; @@
- (ptr->end + 1 - ptr->start)
+ resource_size(ptr)
</smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver wrongly assumes that it is the only entity that can set the
SKBTX_IN_PROGRESS bit of the current skb. Therefore, in the
gfar_clean_tx_ring function, where the TX timestamp is collected if
necessary, the aforementioned bit is used to discriminate whether or not
the TX timestamp should be delivered to the socket's error queue.
But a stacked driver such as a DSA switch can also set the
SKBTX_IN_PROGRESS bit, which is actually exactly what it should do in
order to denote that the hardware timestamping process is undergoing.
Therefore, gianfar would misinterpret the "in progress" bit as being its
own, and deliver a second skb clone in the socket's error queue,
completely throwing off a PTP process which is not expecting to receive
it, _even though_ TX timestamping is not enabled for gianfar.
There have been discussions [0] as to whether non-MAC drivers need or
not to set SKBTX_IN_PROGRESS at all (whose purpose is to avoid sending 2
timestamps, a sw and a hw one, to applications which only expect one).
But as of this patch, there are at least 2 PTP drivers that would break
in conjunction with gianfar: the sja1105 DSA switch and the felix
switch, by way of its ocelot core driver.
So regardless of that conclusion, fix the gianfar driver to not do stuff
based on flags set by others and not intended for it.
[0]: https://www.spinics.net/lists/netdev/msg619699.html
Fixes: f0ee7acfcd ("gianfar: Add hardware TX timestamping support")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the error path some fragments remain DMA mapped. Adding a fix
that unmaps all the fragments. Rework cleanup path to be simpler.
Fixes: 8151ee88ba ("dpaa_eth: use page backed rx buffers")
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon reusing the ptp_qoriq driver, the ptp_qoriq_free() function was
used on the remove path to free any allocated resources.
The ptp_qoriq IRQ is among these resources that are freed in
ptp_qoriq_free() even though it is also a managed one (allocated using
devm_request_threaded_irq).
Drop the resource managed version of requesting the IRQ in order to not
trigger a double free of the interrupt as below:
[ 226.731005] Trying to free already-free IRQ 126
[ 226.735533] WARNING: CPU: 6 PID: 749 at kernel/irq/manage.c:1707
__free_irq+0x9c/0x2b8
[ 226.743435] Modules linked in:
[ 226.746480] CPU: 6 PID: 749 Comm: bash Tainted: G W
5.4.0-03629-gfd7102c32b2c-dirty #912
[ 226.755857] Hardware name: NXP Layerscape LX2160ARDB (DT)
[ 226.761244] pstate: 40000085 (nZcv daIf -PAN -UAO)
[ 226.766022] pc : __free_irq+0x9c/0x2b8
[ 226.769758] lr : __free_irq+0x9c/0x2b8
[ 226.773493] sp : ffff8000125039f0
(...)
[ 226.856275] Call trace:
[ 226.858710] __free_irq+0x9c/0x2b8
[ 226.862098] free_irq+0x30/0x70
[ 226.865229] devm_irq_release+0x14/0x20
[ 226.869054] release_nodes+0x1b0/0x220
[ 226.872790] devres_release_all+0x34/0x50
[ 226.876790] device_release_driver_internal+0x100/0x1c0
Fixes: d346c9e86d ("dpaa2-ptp: reuse ptp_qoriq driver")
Cc: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add external trigger event support
for dpaa2-ptp driver with v2 dprtc_set_irq_mask() API.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/freescale/enetc/enetc_qos.c: In function enetc_setup_tc_cbs:
drivers/net/ethernet/freescale/enetc/enetc_qos.c:195:6: warning: variable tc_max_sized_frame set but not used [-Wunused-but-set-variable]
Fixes: c431047c4e ("enetc: add support Credit Based Shaper(CBS) for hardware offload")
Signed-off-by: Chen Wandun <chenwandun@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide a software TX timestamp and add it to the ethtool query
interface.
skb_tx_timestamp() is also needed if one would like to use PHY
timestamping.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, QUICC_ENGINE depends on PPC32, so this in itself does not
change anything. In order to allow removing the PPC32 dependency from
QUICC_ENGINE and avoid allmodconfig build failures, add this explicit
dependency.
Also, the QE Ethernet has never been integrated on any non-PowerPC SoC
and most likely will not be in the future.
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
The EEE support has not been enabled on ENETC, but it may connect
to a PHY which supports EEE and advertises EEE by default, while
its link partner also advertises EEE. If this happens, the PHY enters
low power mode when the traffic rate is low and causes packet loss.
This patch disables EEE advertisement by default for any PHY that
ENETC connects to, to prevent the above unwanted outcome.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ENETC hardware support the Credit Based Shaper(CBS) which part
of the IEEE-802.1Qav. The CBS driver was loaded by the sch_cbs
interface when set in the QOS in the kernel.
Here is an example command to set 20Mbits bandwidth in 1Gbits port
for taffic class 7:
tc qdisc add dev eth0 root handle 1: mqprio \
num_tc 8 map 0 1 2 3 4 5 6 7 hw 1
tc qdisc replace dev eth0 parent 1:8 cbs \
locredit -1470 hicredit 30 \
sendslope -980000 idleslope 20000 offload 1
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor conflict in drivers/s390/net/qeth_l2_main.c, kept the lock
from commit c8183f5489 ("s390/qeth: fix potential deadlock on
workqueue flush"), removed the code which was removed by commit
9897d583b0 ("s390/qeth: consolidate some duplicated HW cmd code").
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
While using ARCH=mips CROSS_COMPILE=mips-linux-gnu- command to compile,
make C=2 drivers/net/ethernet/freescale/enetc/enetc.o
one warning can be found:
drivers/net/ethernet/freescale/enetc/enetc.c:1439:5:
warning: symbol 'enetc_setup_tc_mqprio' was not declared.
Should it be static?
This patch make symbol enetc_setup_tc_mqprio static.
Fixes: 34c6adf197 ("enetc: Configure the Time-Aware Scheduler via tc-taprio offload")
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style. This fixes various indentation mixups (seven spaces,
tab+one space, etc).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2019-11-20
The following pull-request contains BPF updates for your *net-next* tree.
We've added 81 non-merge commits during the last 17 day(s) which contain
a total of 120 files changed, 4958 insertions(+), 1081 deletions(-).
There are 3 trivial conflicts, resolve it by always taking the chunk from
196e8ca748:
<<<<<<< HEAD
=======
void *bpf_map_area_mmapable_alloc(u64 size, int numa_node);
>>>>>>> 196e8ca748
<<<<<<< HEAD
void *bpf_map_area_alloc(u64 size, int numa_node)
=======
static void *__bpf_map_area_alloc(u64 size, int numa_node, bool mmapable)
>>>>>>> 196e8ca748
<<<<<<< HEAD
if (size <= (PAGE_SIZE << PAGE_ALLOC_COSTLY_ORDER)) {
=======
/* kmalloc()'ed memory can't be mmap()'ed */
if (!mmapable && size <= (PAGE_SIZE << PAGE_ALLOC_COSTLY_ORDER)) {
>>>>>>> 196e8ca748
The main changes are:
1) Addition of BPF trampoline which works as a bridge between kernel functions,
BPF programs and other BPF programs along with two new use cases: i) fentry/fexit
BPF programs for tracing with practically zero overhead to call into BPF (as
opposed to k[ret]probes) and ii) attachment of the former to networking related
programs to see input/output of networking programs (covering xdpdump use case),
from Alexei Starovoitov.
2) BPF array map mmap support and use in libbpf for global data maps; also a big
batch of libbpf improvements, among others, support for reading bitfields in a
relocatable manner (via libbpf's CO-RE helper API), from Andrii Nakryiko.
3) Extend s390x JIT with usage of relative long jumps and loads in order to lift
the current 64/512k size limits on JITed BPF programs there, from Ilya Leoshkevich.
4) Add BPF audit support and emit messages upon successful prog load and unload in
order to have a timeline of events, from Daniel Borkmann and Jiri Olsa.
5) Extension to libbpf and xdpsock sample programs to demo the shared umem mode
(XDP_SHARED_UMEM) as well as RX-only and TX-only sockets, from Magnus Karlsson.
6) Several follow-up bug fixes for libbpf's auto-pinning code and a new API
call named bpf_get_link_xdp_info() for retrieving the full set of prog
IDs attached to XDP, from Toke Høiland-Jørgensen.
7) Add BTF support for array of int, array of struct and multidimensional arrays
and enable it for skb->cb[] access in kfree_skb test, from Martin KaFai Lau.
8) Fix AF_XDP by using the correct number of channels from ethtool, from Luigi Rizzo.
9) Two fixes for BPF selftest to get rid of a hang in test_tc_tunnel and to avoid
xdping to be run as standalone, from Jiri Benc.
10) Various BPF selftest fixes when run with latest LLVM trunk, from Yonghong Song.
11) Fix a memory leak in BPF fentry test run data, from Colin Ian King.
12) Various smaller misc cleanups and improvements mostly all over BPF selftests and
samples, from Daniel T. Lee, Andre Guedes, Anders Roxell, Mao Wenan, Yue Haibing.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
pm_runtime_put_autosuspend in probe will call runtime suspend to
disable clks automatically if CONFIG_PM is defined. (If CONFIG_PM
is not defined, its implementation will be empty, then runtime
suspend will not be called.)
Therefore, we can call pm_runtime_get_sync to runtime resume it
first to enable clks, which matches the runtime suspend. (Only when
CONFIG_PM is defined, otherwise pm_runtime_get_sync will also be
empty, then runtime resume will not be called.)
Then it is fine to disable clks without causing clock count mis-match.
Fixes: c43eab3edd ("net: fec: add missed clk_disable_unprepare in remove")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly to bpf_map's refcnt/usercnt, convert bpf_prog's refcnt to atomic64
and remove artificial 32k limit. This allows to make bpf_prog's refcounting
non-failing, simplifying logic of users of bpf_prog_add/bpf_prog_inc.
Validated compilation by running allyesconfig kernel build.
Suggested-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20191117172806.2195367-3-andriin@fb.com
ENETC has a register PSPEED to indicate the link speed of hardware.
It is need to update accordingly. PSPEED field needs to be updated
with the port speed for QBV scheduling purposes. Or else there is
chance for gate slot not free by frame taking the MAC if PSPEED and
phy speed not match. So update PSPEED when link adjust. This is
implement by the adjust_link.
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ENETC supports in hardware for time-based egress shaping according
to IEEE 802.1Qbv. This patch implement the Qbv enablement by the
hardware offload method qdisc tc-taprio method.
Also update cbdr writeback to up level since control bd ring may
writeback data to control bd ring.
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The setup_dpio() function tries to allocate a number of channels equal
to the number of CPUs online. When there are not enough DPCON objects
already probed, the function will return EPROBE_DEFER. When this
happens, the already allocated channels are not freed. This results in
the incapacity of properly probing the next time around.
Fix this by freeing the channels on the error path.
Fixes: d7f5a9d89a ("dpaa2-eth: defer probe on object allocate")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One conflict in the BPF samples Makefile, some fixes in 'net' whilst
we were converting over to Makefile.target rules in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Return -EOPNOTSUPP instead of -EINVAL if the requested ioctl is not
implemented.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a DPNI is connected to a MAC, export its associated counters.
Ethtool related functions are added in dpaa2_mac for returning the
number of counters, their strings and also their values.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there is an external PHY, pass the wake-on-lan request to the PHY.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there is an attached PHY try to handle the requested ioctl with its
handler, which allows the userspace to access PHY registers, for
example. This will make mii-diag and similar tools work.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
phylink_set_port_modes will be compiled if CONFIG_PHYLINK enabled,
dpaa2_mac_validate will be compiled if CONFIG_FSL_DPAA2_ETH enabled,
it should select CONFIG_PHYLINK when dpaa2_mac_validate call
phylink_set_port_modes
drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.o: In function `dpaa2_mac_validate':
dpaa2-mac.c:(.text+0x3a1): undefined reference to `phylink_set_port_modes'
drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.o: In function `dpaa2_mac_connect':
dpaa2-mac.c:(.text+0x91a): undefined reference to `phylink_create'
dpaa2-mac.c:(.text+0x94e): undefined reference to `phylink_of_phy_connect'
dpaa2-mac.c:(.text+0x97f): undefined reference to `phylink_destroy'
drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.o: In function `dpaa2_mac_disconnect':
dpaa2-mac.c:(.text+0xa9f): undefined reference to `phylink_disconnect_phy'
dpaa2-mac.c:(.text+0xab0): undefined reference to `phylink_destroy'
make: *** [vmlinux] Error 1
Fixes: 7194792308 ("dpaa2-eth: add MAC/PHY support through phylink")
Signed-off-by: Chenwandun <chenwandun@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the phy_mode() function to return the if_mode through an
argument, similar to the new form of of_get_phy_mode().
This will help with handling errors in a common manner and also will fix
an always true condition.
Fixes: 0c65b2b90d ("net: of_get_phy_mode: Change API to solve int/unit warnings")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now the size of a Rx buffer was artificially limited
to 1536B (which happens to be the default, after reset, hardware
value for a Rx buffer). This approach however leaves unused
memory space for Rx packets, since the driver uses a paged
allocation scheme that reserves half a page for each Rx skb.
There's also the inconvenience that frames around 1536 bytes
can get scattered if the limit is slightly exceeded. This limit
can be exceeded even for standard MTU of 1500B traffic, for common
cases like stacked VLANs, or DSA tags.
To address these issues, let's just compute the buffer size
starting from the upper limit of 2KB (half a page) and
subtract the skb overhead and alignment restrictions.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver forgets to disable and unprepare clks when remove.
Add calls to clk_disable_unprepare to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this change of_get_phy_mode() returned an enum,
phy_interface_t. On error, -ENODEV etc, is returned. If the result of
the function is stored in a variable of type phy_interface_t, and the
compiler has decided to represent this as an unsigned int, comparision
with -ENODEV etc, is a signed vs unsigned comparision.
Fix this problem by changing the API. Make the function return an
error, or 0 on success, and pass a pointer, of type phy_interface_t,
where the phy mode should be stored.
v2:
Return with *interface set to PHY_INTERFACE_MODE_NA on error.
Add error checks to all users of of_get_phy_mode()
Fixup a few reverse christmas tree errors
Fixup a few slightly malformed reverse christmas trees
v3:
Fix 0-day reported errors.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only slightly tricky merge conflict was the netdevsim because the
mutex locking fix overlapped a lot of driver reload reorganization.
The rest were (relatively) trivial in nature.
Signed-off-by: David S. Miller <davem@davemloft.net>
The dpaa2-eth driver now has support for connecting to its associated
PHY device found through standard OF bindings.
This happens when the DPNI object (that the driver probes on) gets
connected to a DPMAC. When that happens, the device tree is looked up by
the DPMAC ID, and the associated PHY bindings are found.
The old logic of handling the net device's link state by hand still
needs to be kept, as the DPNI can be connected to other devices on the
bus than a DPMAC: other DPNI, DPSW ports, etc. This logic is only
engaged when there is no DPMAC (and therefore no phylink instance)
attached.
The MC firmware support multiple type of DPMAC links: TYPE_FIXED,
TYPE_PHY. The TYPE_FIXED mode does not require any DPMAC management from
Linux side, and as such, the driver will not handle such a DPMAC.
Although PHYLINK typically handles SFP cages and in-band AN modes, for
the moment the driver only supports the RGMII interfaces found on the
LX2160A. Support for other modes will come later.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the function is called at every link up event, although the
FQID values will only change when the DPNI is disconnected from the
current object and reconnected to a different one.
The patch also avoids the forward declaration of update_tx_fqids.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this change, unbinding the QMan portals did not trigger a
corresponding unbinding of the dpaa_eth making use of it; the first
QMan portal related operation issued afterwards crashed the kernel.
The device link ensures the dpaa_eth dependency upon the qman portal
used is honoured at the QMan portal removal.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure all the frames that are in flight have time to be processed
before the interface is completely brought down. Add a missing delay
for the Rx path.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
User reports that an application making an (incorrect) call to
restart AN on a fixed link DPAA interface triggers an error in
the kernel log while the returned EINVAL should be enough.
Reported-by: Joakim Tjernlund <Joakim.Tjernlund@infinera.com>
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to this change, the frames dropped on receive or transmit
were not displayed in the ethtool statistics, leaving the dropped
frames unaccounted for.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a page to store the scatter gather table on the transmit path.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of reading skb fields, use information from the DPAA frame
descriptor.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dpaa_cleanup_tx_fd() function is called by the frame transmit
confirmation callback but also on several error paths. This function
is reading the transmit timestamp value. Avoid reading an invalid
timestamp value on the error paths.
Fixes: 4664856e9c ("dpaa_eth: add support for hardware timestamping")
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DMA unmapping is required before accessing the HW provided timestamping
information.
Fixes: 4664856e9c ("dpaa_eth: add support for hardware timestamping")
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the buffers used for reception from netdev_frags to pages.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the DPAA Ethernet driver is using three buffer pools
for each interface, with three different sizes for the buffers
provided for the FMan reception path. This patch reduces the
number of buffer pools to one per interface. This change is in
preparation of another, that will be switching from netdev_frags
to page backed buffers for the receive path.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use platform_get_irq_byname_optional() and platform_get_irq_optional()
instead of platform_get_irq_byname() and platform_get_irq() for optional
IRQs to avoid below error message during probe:
[ 0.795803] fec 30be0000.ethernet: IRQ pps not found
[ 0.800787] fec 30be0000.ethernet: IRQ index 3 not found
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Failed to get irq using name is NOT fatal as driver will use index
to get irq instead, use platform_get_irq_byname_optional() instead
of platform_get_irq_byname() to avoid below error message during
probe:
[ 0.819312] fec 30be0000.ethernet: IRQ int0 not found
[ 0.824433] fec 30be0000.ethernet: IRQ int1 not found
[ 0.829539] fec 30be0000.ethernet: IRQ int2 not found
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pointer bdp is being assigned with a value that is never
read, so the assignment is redundant and hence can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch corrects the SPDX License Identifier style in
header files related to DPAA2 Ethernet driver supporting
Freescale SoCs with DPAA2. For C header files
Documentation/process/license-rules.rst mandates C-like comments
(opposed to C source files where C++ style should be used)
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newline was missing at the end of the error message.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unused struct member second_largest_buf_size. Also, an out of
bounds access would have occurred in the removed code if there was only
one buffer pool in use.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DPAA Ethernet driver is using the FMan MAC as the device for DMA
mapping. This is not actually correct, as the real DMA device is the
FMan port (the FMan Rx port for reception and the FMan Tx port for
transmission). Changing the device used for DMA mapping to the Fman
Rx and Tx port devices.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an API that retrieves the 'struct device' that the specified FMan
port probed against. The new API will be used in a subsequent patch
that corrects the DMA devices used by the dpaa_eth driver.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Condition was previously checked, removing duplicate code.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the DPAA 1 Ethernet driver gets probed before the QBMan driver it will
cause a boot crash. Add predictability in the probing order by deferring
the Ethernet driver probe after QBMan and portals by using the recently
introduced QBMan APIs.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The liodn base registers are specific to PAMU based NXP systems and are
reserved on SMMU based ones. Don't access them unless PAMU is compiled in.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Depending on when MC connects the DPNI to a MAC, Tx FQIDs may
not be available during probe time.
Read the FQIDs each time the link goes up to avoid using invalid
values. In case an error occurs or an invalid value is retrieved,
fall back to QDID-based enqueueing.
Fixes: 1fa0f68c92 ("dpaa2-eth: Use FQ-based DPIO enqueue API")
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IRQ for the DPNI endpoint change event, resolving the issue
when a dynamically created DPNI gets a randomly generated hw address
when the endpoint is a DPMAC object.
Signed-off-by: Florin Chiculita <florinlaurentiu.chiculita@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Throughout the driver there are several places where we wait
indefinitely for DPIO portal commands to be executed, while
the portal returns a busy response code.
Even though in theory we are guaranteed the portals become
available eventually, in practice the QBMan hardware module
may become unresponsive in various corner cases.
Make sure we can never get stuck in an infinite while loop
by adding a retry counter for all portal commands.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't print error message for a successful return value.
Fixes: d84c3a4ded ("dpaa2-eth: Add new DPNI statistics counters")
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove one function call whose result was not used anywhere.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "priv->if_mode" is type phy_interface_t which is an enum. In this
context GCC will treat the enum as an unsigned int so this error
handling is never triggered.
Fixes: d4fd0404c1 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warning:
drivers/net/ethernet/freescale/gianfar.c:2070:6:
warning: symbol 'reset_gfar' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Historically, gianfar only used phy-connection-type DT property when
connected to PHY in the rgmii-id mode. It ignored the property otherwise,
relying on the connection type auto-detection carried out by MAC and
providing that reconstructed mode to of_phy_connect(). It also did not
consider alternative phy-mode property at all.
Make the driver properly query DT node for PHY connection type first and
use an obtained value if it was specified there. Otherwise, if a particular
DT relies on connection type auto-detection, fall back to reconstructing
the value from MAC registers, as before.
Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove now unused macro and structure definitions from gianfar.h that have
accumulated there over time.
Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make functions that do not have callers outside the translation unit they
are defined in static.
Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove forward declarations of various static functions located in two
driver implementation files and rearrange the corresponding definitions
accordingly.
This patch only introduces mechanical changes, namely it removes forward
declarations and moves function definitions around; it does not change any
functionality.
Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting with firmware version MC10.18.0, a new counter for in flight
Tx frames is offered. Use it when bringing down the interface to
determine when all pending Tx frames have been processed by hardware
instead of sleeping a fixed amount of time.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent firmware versions expose more DPNI counters.
Export relevant ones via ethtool -S.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we prepare to read more pages from the DPNI stat counters,
reorganize the code a bit to make it easier to extend.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call to 'pci_free_irq_vectors()' are missing both in the error handling
path of the probe function, and in the remove function.
Add them.
Fixes: 19971f5ea0 ("enetc: add PTP clock driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting with firmware version MC10.18.0, we have support for
L2 flow control. Asymmetrical configuration (Rx or Tx only) is
supported, but not pause frame autonegotioation.
Pause frame configuration is done via ethtool. By default, we start
with flow control enabled on both Rx and Tx. Changes are propagated
to hardware through firmware commands, using two flags (PAUSE,
ASYM_PAUSE) to specify Rx and Tx pause configuration, as follows:
PAUSE | ASYM_PAUSE | Rx pause | Tx pause
----------------------------------------
0 | 0 | disabled | disabled
0 | 1 | disabled | enabled
1 | 0 | enabled | enabled
1 | 1 | enabled | disabled
The hardware can automatically send pause frames when the number
of buffers in the pool goes below a predefined threshold. Due to
this, flow control is incompatible with Rx frame queue taildrop
(both mechanisms target the case when processing of ingress
frames can't keep up with the Rx rate; for large frames, the number
of buffers in the pool may never get low enough to trigger pause
frames as long as taildrop is enabled). So we set pause frame
generation and Rx FQ taildrop as mutually exclusive.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Whenever a link state change occurs, we get notified and save
the new link settings in the device's private data. In ethtool
get_link_ksettings, use the stored state instead of interrogating
the firmware each time.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We only support fixed-link for now, so there is no point in
offering users the option to change link settings via ethtool.
Functionally there is no change, since firmware prevents us from
changing link parameters anyway.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dev_kfree_skb() function performs also input parameter validation.
Thus the test around the shown calls is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
IEEE 802.3ae clause 45 defines a modified MDIO protocol that uses a two
staged access model in order to increase the address space.
This patch adds support for C45 MDIO read and write accesses, which are
used whenever the MII_ADDR_C45 flag in the regnum argument is set.
In case it is not set, C22 accesses are used as before.
Signed-off-by: Marco Hartmann <marco.hartmann@nxp.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Because we don't care about the individual files, we can remove the
stored dentry for the files, as they are not needed to be kept track of
at all.
Cc: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
refcount_t is better for reference counters since its
implementation can prevent overflows.
So convert atomic_t ref counters to refcount_t.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ENETC ports can manage the MDIO bus via local register
interface. However there's also a centralized way
to manage the MDIO bus, via the MDIO PCIe endpoint
device integrated by the same root complex that also
integrates the ENETC ports (eth controllers).
Depending on board design and use case, centralized
access to MDIO may be better than using local ENETC
port registers. For instance, on the LS1028A QDS board
where MDIO muxing is required. Also, the LS1028A on-chip
switch doesn't have a local MDIO register interface.
The current patch registers the above PCIe endpoint as a
separate MDIO bus and provides a driver for it by re-using
the code used for local MDIO access. It also allows the
ENETC port PHYs to be managed by this driver if the local
"mdio" node is missing from the ENETC port node.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean up overcomplicated makefile to make it more maintainable.
Basically, there's a set of common objects shared between
the PF and VF driver modules. This can be implemented in a
simpler way, without conditionals, less repetition, allowing
also for easier updates in the future.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
What's needed is basically a pointer to the mdio registers.
This is one way to store it inside bus->priv allocated space,
without upsetting sparse.
Reworked accessors to avoid __iomem casting.
Used devm_* variant to further clean up the init error /
remove paths.
Fixes following sparse warning:
warning: incorrect type in assignment (different address spaces)
expected void *priv
got struct enetc_mdio_regs [noderef] <asn:2>*[assigned] regs
Fixes: ebfcb23d62 ("enetc: Add ENETC PF level external MDIO support")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like FSL_ENETC, when CONFIG_FSL_ENETC_VF is set,
we should select PHYLIB, otherwise building still fails:
drivers/net/ethernet/freescale/enetc/enetc.o: In function `enetc_open':
enetc.c:(.text+0x2744): undefined reference to `phy_start'
enetc.c:(.text+0x282c): undefined reference to `phy_disconnect'
drivers/net/ethernet/freescale/enetc/enetc.o: In function `enetc_close':
enetc.c:(.text+0x28f8): undefined reference to `phy_stop'
enetc.c:(.text+0x2904): undefined reference to `phy_disconnect'
drivers/net/ethernet/freescale/enetc/enetc_ethtool.o:(.rodata+0x3f8): undefined reference to `phy_ethtool_get_link_ksettings'
drivers/net/ethernet/freescale/enetc/enetc_ethtool.o:(.rodata+0x400): undefined reference to `phy_ethtool_set_link_ksettings'
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: d4fd0404c1 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use accessor functions for skb fragment's page_offset instead
of direct references, in preparation for bvec conversion.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If PHYLIB is not set, build enetc will fails:
drivers/net/ethernet/freescale/enetc/enetc.o: In function `enetc_open':
enetc.c: undefined reference to `phy_disconnect'
enetc.c: undefined reference to `phy_start'
drivers/net/ethernet/freescale/enetc/enetc.o: In function `enetc_close':
enetc.c: undefined reference to `phy_stop'
enetc.c: undefined reference to `phy_disconnect'
drivers/net/ethernet/freescale/enetc/enetc_ethtool.o: undefined reference to `phy_ethtool_get_link_ksettings'
drivers/net/ethernet/freescale/enetc/enetc_ethtool.o: undefined reference to `phy_ethtool_set_link_ksettings'
drivers/net/ethernet/freescale/enetc/enetc_mdio.o: In function `enetc_mdio_probe':
enetc_mdio.c: undefined reference to `mdiobus_alloc_size'
enetc_mdio.c: undefined reference to `mdiobus_free'
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: d4fd0404c1 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fm_set_max_frm() existed in the Freescale SDK as a callback for an
early_param. When this code was ported to the upstream kernel the
early_param was converted to a module_param making the reference to the
function incorrect. The rest of the comment already does a good job of
explaining the parameter so removing the reference to the non-existent
function seems like the best thing to do.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
I missed a few places. One is in some ifdeffed code which will probably
never be re-enabled; the others are in drivers which can't currently be
compiled on x86.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unifying the skb_frag and bio_vec, use the fine
accessors which already exist and use skb_frag_t instead of
struct skb_frag_struct.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
kvzalloc already zeroes the memory during the allocation.
pci_alloc_consistent calls dma_alloc_coherent directly.
In commit 518a2f1925
("dma-mapping: zero memory returned from dma_alloc_*"),
dma_alloc_coherent has already zeroed the memory.
So the memset after these function is not needed.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add interrupt support for dpaa2 ptp clock,
including MC APIs and PPS interrupt support. Other events
haven't been supported in MC by now.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although dpaa2-ptp.c driver is a fsl_mc_driver which
is using MC APIs for register accessing, it's same IP
block with eTSEC/DPAA/ENETC 1588 timer.
This patch is to convert to reuse ptp_qoriq driver by
using register ioremap and dropping related MC APIs.
However the interrupts could only be handled by MC which
fires MSIs to ARM cores. So the interrupt enabling and
handling still rely on MC APIs.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement mqprio qdisc support by mapping traffic classes to
different hardware enqueue priorities. The maximum number of
supported traffic classes is an attribute of each DPNI object.
The traffic classes map to hardware priorities from highest (0)
to lowest (highest prio number). The skb priority information
received from the stack is used to select the hardware Tx queue
on which to enqueue the frame.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Bogdan Purcareata <bogdan.purcareata@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
