PAE40 confiuration in hardware extends some of the address registers
for TLB/cache ops to 2 words.
So far kernel was NOT setting the higher word if feature was not enabled
in software which is wrong. Those need to be set to 0 in such case.
Normally this would be done in the cache flush / tlb ops, however since
these registers only exist conditionally, this would have to be
conditional to a flag being set on boot which is expensive/ugly -
specially for the more common case of PAE exists but not in use.
Optimize that by zero'ing them once at boot - nobody will write to
them afterwards
Cc: stable@vger.kernel.org #4.4+
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
It is necessary to explicitly set both SLC_AUX_RGN_START1 and SLC_AUX_RGN_END1
which hold MSB bits of the physical address correspondingly of region start
and end otherwise SLC region operation is executed in unpredictable manner
Without this patch, SLC flushes on HSDK (IOC disabled) were taking
seconds.
Cc: stable@vger.kernel.org #4.4+
Reported-by: Vladimir Kondratiev <vladimir.kondratiev@intel.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
[vgupta: PAR40 regs only written if PAE40 exist]
c70c473396 "ARCv2: SLC: Make sure busy bit is set properly on SLC flushing"
fixes problem for entire SLC operation where the problem was initially
caught. But given a nature of the issue it is perfectly possible for
busy bit to be read incorrectly even when region operation was started.
So extending initial fix for regional operation as well.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: stable@vger.kernel.org #4.10
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Stack guard page is a useful feature to reduce a risk of stack smashing
into a different mapping. We have been using a single page gap which
is sufficient to prevent having stack adjacent to a different mapping.
But this seems to be insufficient in the light of the stack usage in
userspace. E.g. glibc uses as large as 64kB alloca() in many commonly
used functions. Others use constructs liks gid_t buffer[NGROUPS_MAX]
which is 256kB or stack strings with MAX_ARG_STRLEN.
This will become especially dangerous for suid binaries and the default
no limit for the stack size limit because those applications can be
tricked to consume a large portion of the stack and a single glibc call
could jump over the guard page. These attacks are not theoretical,
unfortunatelly.
Make those attacks less probable by increasing the stack guard gap
to 1MB (on systems with 4k pages; but make it depend on the page size
because systems with larger base pages might cap stack allocations in
the PAGE_SIZE units) which should cover larger alloca() and VLA stack
allocations. It is obviously not a full fix because the problem is
somehow inherent, but it should reduce attack space a lot.
One could argue that the gap size should be configurable from userspace,
but that can be done later when somebody finds that the new 1MB is wrong
for some special case applications. For now, add a kernel command line
option (stack_guard_gap) to specify the stack gap size (in page units).
Implementation wise, first delete all the old code for stack guard page:
because although we could get away with accounting one extra page in a
stack vma, accounting a larger gap can break userspace - case in point,
a program run with "ulimit -S -v 20000" failed when the 1MB gap was
counted for RLIMIT_AS; similar problems could come with RLIMIT_MLOCK
and strict non-overcommit mode.
Instead of keeping gap inside the stack vma, maintain the stack guard
gap as a gap between vmas: using vm_start_gap() in place of vm_start
(or vm_end_gap() in place of vm_end if VM_GROWSUP) in just those few
places which need to respect the gap - mainly arch_get_unmapped_area(),
and and the vma tree's subtree_gap support for that.
Original-patch-by: Oleg Nesterov <oleg@redhat.com>
Original-patch-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Tested-by: Helge Deller <deller@gmx.de> # parisc
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- AXS10x platform clk updates for I2S, PGU
- Adding region based cache flush operation for ARCv2 cores
- Enforcing PAE40 dependency on HIGHMEM
- ptrace support for additional regs in ARCv2 cores
- Fix build failure in linux-next dut to a header include ordering change
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=zJ9B
-----END PGP SIGNATURE-----
Merge tag 'arc-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC updates from Vineet Gupta:
- AXS10x platform clk updates for I2S, PGU
- add region based cache flush operation for ARCv2 cores
- enforce PAE40 dependency on HIGHMEM
- ptrace support for additional regs in ARCv2 cores
- fix build failure in linux-next dut to a header include ordering
change
* tag 'arc-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
Revert "ARCv2: Allow enabling PAE40 w/o HIGHMEM"
ARC: mm: fix build failure in linux-next for UP builds
ARCv2: ptrace: provide regset for accumulator/r30 regs
elf: Add ARCv2 specific core note section
ARCv2: mm: micro-optimize region flush generated code
ARCv2: mm: Merge 2 updates to DC_CTRL for region flush
ARCv2: mm: Implement cache region flush operations
ARC: mm: Move full_page computation into cache version agnostic wrapper
arc: axs10x: Fix ARC PGU default clock frequency
arc: axs10x: Add DT bindings for I2S audio playback
Region Flush has a weird programming model.
1. Flush or Invalidate is selected by DC_CTRL.RGN_OP
2 Flush-n-Invalidate is done by DC_CTRL.IM
Given the code structuring before, case #2 above was generating two
seperate updates to DC_CTRL which was pointless.
| 80a342b0 <__dma_cache_wback_inv_l1>:
| 80a342b0: clri r4
| 80a342b4: lr r2,[dc_ctrl]
| 80a342b8: bset_s r2,r2,0x6
| 80a342ba: sr r2,[dc_ctrl] <-- FIRST
|
| 80a342be: bmskn r3,r0,0x5
|
| 80a342c2: lr r2,[dc_ctrl]
| 80a342c6: and r2,r2,0xfffff1ff
| 80a342ce: bset_s r2,r2,0x9
| 80a342d0: sr r2,[dc_ctrl] <-- SECOND
|
| 80a342d4: add_s r1,r1,0x3f
| 80a342d6: bmsk_s r0,r0,0x5
| 80a342d8: add_s r0,r0,r1
| 80a342da: add_s r0,r0,r3
| 80a342dc: sr r0,[78]
| 80a342e0: sr r3,[77]
|...
|...
So move setting of DC_CTRL.RGN_OP into __before_dc_op() and combine with
any other update.
| 80b63324 <__dma_cache_wback_inv_l1>:
| 80b63324: clri r3
| 80b63328: lr r2,[dc_ctrl]
| 80b6332c: and r2,r2,0xfffff1ff
| 80b63334: or r2,r2,576
| 80b63338: sr r2,[dc_ctrl]
|
| 80b6333c: add_s r1,r1,0x3f
| 80b6333e: bmskn r2,r0,0x5
| 80b63342: add_s r0,r0,r1
| 80b63344: sr r0,[78]
| 80b63348: sr r2,[77]
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Pull uaccess unification updates from Al Viro:
"This is the uaccess unification pile. It's _not_ the end of uaccess
work, but the next batch of that will go into the next cycle. This one
mostly takes copy_from_user() and friends out of arch/* and gets the
zero-padding behaviour in sync for all architectures.
Dealing with the nocache/writethrough mess is for the next cycle;
fortunately, that's x86-only. Same for cleanups in iov_iter.c (I am
sold on access_ok() in there, BTW; just not in this pile), same for
reducing __copy_... callsites, strn*... stuff, etc. - there will be a
pile about as large as this one in the next merge window.
This one sat in -next for weeks. -3KLoC"
* 'work.uaccess' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (96 commits)
HAVE_ARCH_HARDENED_USERCOPY is unconditional now
CONFIG_ARCH_HAS_RAW_COPY_USER is unconditional now
m32r: switch to RAW_COPY_USER
hexagon: switch to RAW_COPY_USER
microblaze: switch to RAW_COPY_USER
get rid of padding, switch to RAW_COPY_USER
ia64: get rid of copy_in_user()
ia64: sanitize __access_ok()
ia64: get rid of 'segment' argument of __do_{get,put}_user()
ia64: get rid of 'segment' argument of __{get,put}_user_check()
ia64: add extable.h
powerpc: get rid of zeroing, switch to RAW_COPY_USER
esas2r: don't open-code memdup_user()
alpha: fix stack smashing in old_adjtimex(2)
don't open-code kernel_setsockopt()
mips: switch to RAW_COPY_USER
mips: get rid of tail-zeroing in primitives
mips: make copy_from_user() zero tail explicitly
mips: clean and reorder the forest of macros...
mips: consolidate __invoke_... wrappers
...
As reported in STAR 9001165532, an SLC control reg read (for checking
busy state) right after SLC invalidate command may incorrectly return
NOT busy causing software to NOT spin-wait while operation is underway.
(and for some reason this only happens if L1 cache is also disabled - as
required by IOC programming model)
Suggested workaround is to do an additional Control Reg read, which
ensures the 2nd read gets the right status.
Cc: stable@vger.kernel.org #4.10
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
[vgupta: reworte changelog a bit]
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
... and switch to generic out of line version in lib/usercopy.c
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Update code that relied on sched.h including various MM types for them.
This will allow us to remove the <linux/mm_types.h> include from <linux/sched.h>.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to split more MM APIs out of <linux/sched.h>, which
will have to be picked up from a couple of .c files.
The APIs that we are going to move are:
arch_pick_mmap_layout()
arch_get_unmapped_area()
arch_get_unmapped_area_topdown()
mm_update_next_owner()
Include the header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to split <linux/sched/signal.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/signal.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Bart Van Assche noted that the ib DMA mapping code was significantly
similar enough to the core DMA mapping code that with a few changes
it was possible to remove the IB DMA mapping code entirely and
switch the RDMA stack to use the core DMA mapping code. This resulted
in a nice set of cleanups, but touched the entire tree. This branch
will be submitted separately to Linus at the end of the merge window
as per normal practice for tree wide changes like this.
-----BEGIN PGP SIGNATURE-----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=e0Si
-----END PGP SIGNATURE-----
Merge tag 'for-next-dma_ops' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma DMA mapping updates from Doug Ledford:
"Drop IB DMA mapping code and use core DMA code instead.
Bart Van Assche noted that the ib DMA mapping code was significantly
similar enough to the core DMA mapping code that with a few changes it
was possible to remove the IB DMA mapping code entirely and switch the
RDMA stack to use the core DMA mapping code.
This resulted in a nice set of cleanups, but touched the entire tree
and has been kept separate for that reason."
* tag 'for-next-dma_ops' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (37 commits)
IB/rxe, IB/rdmavt: Use dma_virt_ops instead of duplicating it
IB/core: Remove ib_device.dma_device
nvme-rdma: Switch from dma_device to dev.parent
RDS: net: Switch from dma_device to dev.parent
IB/srpt: Modify a debug statement
IB/srp: Switch from dma_device to dev.parent
IB/iser: Switch from dma_device to dev.parent
IB/IPoIB: Switch from dma_device to dev.parent
IB/rxe: Switch from dma_device to dev.parent
IB/vmw_pvrdma: Switch from dma_device to dev.parent
IB/usnic: Switch from dma_device to dev.parent
IB/qib: Switch from dma_device to dev.parent
IB/qedr: Switch from dma_device to dev.parent
IB/ocrdma: Switch from dma_device to dev.parent
IB/nes: Remove a superfluous assignment statement
IB/mthca: Switch from dma_device to dev.parent
IB/mlx5: Switch from dma_device to dev.parent
IB/mlx4: Switch from dma_device to dev.parent
IB/i40iw: Remove a superfluous assignment statement
IB/hns: Switch from dma_device to dev.parent
...
This file was only including module.h for exception table related
functions. We've now separated that content out into its own file
"extable.h" so now move over to that and avoid all the extra header
content in module.h that we don't really need to compile this file.
Since the file does have some EXPORT_SYMBOL, we add export.h include.
Cc: Vineet Gupta <vgupta@synopsys.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Cc: linux-snps-arc@lists.infradead.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The programming model has been fixed with prev patches so re-enable it
by default
This reverts commit 23cb1f6440.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
arc_cache_init() is called for each core so can't be tagged __init.
However bulk of it is only executed by master core and thus is candidate
for __init reaping.
So split it up to allow that.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
vs. fixed 512M before.
But this still assumes that all of memory is under IOC which may not be
true for the SoC. Improve that later when this becomes a real issue, by
specifying this from DT.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
On AXS103 release bitfiles, DMA data corruptions were seen because IOC
setup was not following the recommended way in documentation.
Flipping IOC on when caches are enabled or coherency transactions are in
flight, might cause some of the memory operations to not observe
coherency as expected.
So strictly follow the programming model recommendations as documented
in comment header above arc_ioc_setup()
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
An ARC700 customer reported linux boot crashes when upgrading to bigger
L1 dcache (64K from 32K). Turns out they had an aliasing VIPT config and
current code only assumed 2 colours, while theirs had 4. So default to 4
colours and complain if there are fewer. Ideally this needs to be a
Kconfig option, but heck that's too much of hassle for a single user.
Cc: stable@vger.kernel.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Historical MMU revisions have been paired with Cache revision updates
which are captured in MMU and Cache Build Configuration Registers respectively.
This was used in boot code to check for configurations mismatches,
speically in simulations (such as running with non existent caches,
non pairing MMU and Cache version etc). This can instead be inferred
from other cache params such as line size. So remove @ver from post
processed @cpuinfo which could be used later to save soem other
interesting info.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Patch series "Add support for DMA writable pages being writable by the
network stack", v3.
The first 19 patches in the set add support for the DMA attribute
DMA_ATTR_SKIP_CPU_SYNC on multiple platforms/architectures. This is
needed so that we can flag the calls to dma_map/unmap_page so that we do
not invalidate cache lines that do not currently belong to the device.
Instead we have to take care of this in the driver via a call to
sync_single_range_for_cpu prior to freeing the Rx page.
Patch 20 adds support for dma_map_page_attrs and dma_unmap_page_attrs so
that we can unmap and map a page using the DMA_ATTR_SKIP_CPU_SYNC
attribute.
Patch 21 adds support for freeing a page that has multiple references
being held by a single caller. This way we can free page fragments that
were allocated by a given driver.
The last 2 patches use these updates in the igb driver, and lay the
groundwork to allow for us to reimplement the use of build_skb.
This patch (of 23):
This change allows us to pass DMA_ATTR_SKIP_CPU_SYNC which allows us to
avoid invoking cache line invalidation if the driver will just handle it
later via a sync_for_cpu or sync_for_device call.
Link: http://lkml.kernel.org/r/20161110113419.76501.38491.stgit@ahduyck-blue-test.jf.intel.com
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We used to use generic implementation of dma_map_ops.mmap which is
dma_common_mmap() but that only worked for simpler cached mappings when
vaddr = paddr.
If a driver requests uncached DMA buffer kernel maps it to virtual
address so that MMU gets involved and page uncached status takes into
account. In that case usage of dma_common_mmap() lead to mapping of
vaddr to vaddr for user-space which is obviously wrong. For more detals
please refer to verbose explanation here [1].
So here we implement our own version of mmap() which always deals
with dma_addr and maps underlying memory to user-space properly
(note that DMA buffer mapped to user-space is always uncached
because there's no way to properly manage cache from user-space).
[1] https://lkml.org/lkml/2016/10/26/973
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: <stable@vger.kernel.org> #4.5+
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Previously we would not print the case when IOC existed but was not
enabled.
And while at it, reduce one line off boot printing by consolidating
the Peripheral address space and IO-Coherency which in a way
applies to them
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
if user disables IOC from debugger at startup (by clearing @ioc_enable),
@ioc_exists is cleared too. This means boot prints don't capture the
fact that IOC was present but disabled which could be misleading.
So invert how we use @ioc_enable and @ioc_exists and make it more
canonical. @ioc_exists represent whether hardware is present or not and
stays same whether enabled or not. @ioc_enable is still user driven,
but will be auto-disabled if IOC hardware is not present, i.e. if
@ioc_exist=0. This is opposite to what we were doing before, but much
clearer.
This means @ioc_enable is now the "exported" toggle in rest of code such
as dma mapping API.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
HS release 3.0 provides for even more flexibility in specifying the
volatile address space for mapping peripherals.
With HS 2.1 @start was made flexible / programmable - with HS 3.0 even
@end can be setup (vs. fixed to 0xFFFF_FFFF before).
So add code to reflect that and while at it remove an unused struct
defintion
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
For resources shared by all cores such as SLC and IOC, only the master
core needs to do any setups / enabling / disabling etc.
Cc: <stable@vger.kernel.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The dma-mapping core and the implementations do not change the DMA
attributes passed by pointer. Thus the pointer can point to const data.
However the attributes do not have to be a bitfield. Instead unsigned
long will do fine:
1. This is just simpler. Both in terms of reading the code and setting
attributes. Instead of initializing local attributes on the stack
and passing pointer to it to dma_set_attr(), just set the bits.
2. It brings safeness and checking for const correctness because the
attributes are passed by value.
Semantic patches for this change (at least most of them):
virtual patch
virtual context
@r@
identifier f, attrs;
@@
f(...,
- struct dma_attrs *attrs
+ unsigned long attrs
, ...)
{
...
}
@@
identifier r.f;
@@
f(...,
- NULL
+ 0
)
and
// Options: --all-includes
virtual patch
virtual context
@r@
identifier f, attrs;
type t;
@@
t f(..., struct dma_attrs *attrs);
@@
identifier r.f;
@@
f(...,
- NULL
+ 0
)
Link: http://lkml.kernel.org/r/1468399300-5399-2-git-send-email-k.kozlowski@samsung.com
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Acked-by: Mark Salter <msalter@redhat.com> [c6x]
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com> [cris]
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> [drm]
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Joerg Roedel <jroedel@suse.de> [iommu]
Acked-by: Fabien Dessenne <fabien.dessenne@st.com> [bdisp]
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com> [vb2-core]
Acked-by: David Vrabel <david.vrabel@citrix.com> [xen]
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> [xen swiotlb]
Acked-by: Joerg Roedel <jroedel@suse.de> [iommu]
Acked-by: Richard Kuo <rkuo@codeaurora.org> [hexagon]
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Acked-by: Gerald Schaefer <gerald.schaefer@de.ibm.com> [s390]
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no> [avr32]
Acked-by: Vineet Gupta <vgupta@synopsys.com> [arc]
Acked-by: Robin Murphy <robin.murphy@arm.com> [arm64 and dma-iommu]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There was only one use of __initdata_refok and __exit_refok
__init_refok was used 46 times against 82 for __ref.
Those definitions are obsolete since commit 312b1485fb ("Introduce new
section reference annotations tags: __ref, __refdata, __refconst")
This patch removes the following compatibility definitions and replaces
them treewide.
/* compatibility defines */
#define __init_refok __ref
#define __initdata_refok __refdata
#define __exit_refok __ref
I can also provide separate patches if necessary.
(One patch per tree and check in 1 month or 2 to remove old definitions)
[akpm@linux-foundation.org: coding-style fixes]
Link: http://lkml.kernel.org/r/1466796271-3043-1-git-send-email-fabf@skynet.be
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Things have been calm here - nothing much except for a few fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=/rhI
-----END PGP SIGNATURE-----
Merge tag 'arc-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC updates from Vineet Gupta:
"Things have been calm here - nothing much except for a few fixes"
* tag 'arc-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: mm: don't loose PTE_SPECIAL in pte_modify()
ARC: dma: fix address translation in arc_dma_free
ARC: typo fix in mm/ioremap.c
ARC: fix linux-next build breakage
page should be calculated using physical address.
If platform uses non-trivial dma-to-phys memory translation,
dma_handle should be converted to physicval address before
calculation of page.
Failing to do so results in struct page * pointing to
wrong or non-existent memory.
Fixes: f2e3d55397 ("ARC: dma: reintroduce platform specific dma<->phys")
Cc: stable@vger.kernel.org #4.6+
Signed-off-by: Vladimir Kondratiev <vladimir.kondratiev@intel.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
NPS use special mapping right below TASK_SIZE.
Hence we need to lower STACK_TOP so that user stack won't
overlap NPS special mapping.
Signed-off-by: Noam Camus <noamc@ezchip.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
On ARC, lower 2G of address space is translated and used for
- user vaddr space (region 0 to 5)
- unused kernel-user gutter (region 6)
- kernel vaddr space (region 7)
where each region simply represents 256MB of address space.
The kernel vaddr space of 256MB is used to implement vmalloc, modules
So far this was enough, but not on EZChip system with 4K CPUs (given
that per cpu mechanism uses vmalloc for allocating chunks)
So allow VMALLOC_SIZE to be configurable by expanding down into the unused
kernel-user gutter region which at default 256M was excessive anyways.
Also use _BITUL() to fix a build error since PGDIR_SIZE cannot use "1UL"
as called from assembly code in mm/tlbex.S
Signed-off-by: Noam Camus <noamc@ezchip.com>
[vgupta: rewrote changelog, debugged bootup crash due to int vs. hex]
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Initial HIGHMEM support on ARC was introduced for PAE40 where the low
memory (0x8000_0000 based) and high memory (0x1_0000_0000) were
physically contiguous. So CONFIG_FLATMEM sufficed (despite a peipheral
hole in the middle, which wasted a bit of struct page memory, but things
worked).
However w/o PAE, highmem was not possible and we could only reach
~1.75GB of DDR. Now there is a use case to access ~4GB of DDR w/o PAE40
The idea is to have low memory at canonical 0x8000_0000 and highmem
at 0 so enire 4GB address space is available for physical addressing
This needs additional platform/interconnect mapping to convert
the non contiguous physical addresses into linear bus adresses.
From Linux point of view, non contiguous divide means FLATMEM no
longer works and DISCONTIGMEM is needed to track the pfns in the 2
regions.
This scheme would also work for PAE40, only better in that we don't
waste struct page memory for the peripheral hole.
The DT description will be something like
memory {
...
reg = <0x80000000 0x200000000 /* 512MB: lowmem */
0x00000000 0x10000000>; /* 256MB: highmem */
}
Signed-off-by: Noam Camus <noamc@ezchip.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} macros were introduced *long* time
ago with promise that one day it will be possible to implement page
cache with bigger chunks than PAGE_SIZE.
This promise never materialized. And unlikely will.
We have many places where PAGE_CACHE_SIZE assumed to be equal to
PAGE_SIZE. And it's constant source of confusion on whether
PAGE_CACHE_* or PAGE_* constant should be used in a particular case,
especially on the border between fs and mm.
Global switching to PAGE_CACHE_SIZE != PAGE_SIZE would cause to much
breakage to be doable.
Let's stop pretending that pages in page cache are special. They are
not.
The changes are pretty straight-forward:
- <foo> << (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- <foo> >> (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} -> PAGE_{SIZE,SHIFT,MASK,ALIGN};
- page_cache_get() -> get_page();
- page_cache_release() -> put_page();
This patch contains automated changes generated with coccinelle using
script below. For some reason, coccinelle doesn't patch header files.
I've called spatch for them manually.
The only adjustment after coccinelle is revert of changes to
PAGE_CAHCE_ALIGN definition: we are going to drop it later.
There are few places in the code where coccinelle didn't reach. I'll
fix them manually in a separate patch. Comments and documentation also
will be addressed with the separate patch.
virtual patch
@@
expression E;
@@
- E << (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
expression E;
@@
- E >> (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
@@
- PAGE_CACHE_SHIFT
+ PAGE_SHIFT
@@
@@
- PAGE_CACHE_SIZE
+ PAGE_SIZE
@@
@@
- PAGE_CACHE_MASK
+ PAGE_MASK
@@
expression E;
@@
- PAGE_CACHE_ALIGN(E)
+ PAGE_ALIGN(E)
@@
expression E;
@@
- page_cache_get(E)
+ get_page(E)
@@
expression E;
@@
- page_cache_release(E)
+ put_page(E)
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The peripheral address space is architectural address window which is
uncached and typically used to wire up peripherals.
For ARC700 cores (ARCompact ISA based) this was fixed to 1GB region
0xC000_0000 - 0xFFFF_FFFF.
For ARCv2 based HS38 cores the start address is flexible and can be
0xC, 0xD, 0xE, 0xF 000_000 by programming AUX_NON_VOLATILE_LIMIT reg
(typically done in bootloader)
Further in cas of PAE, the physical address can extend beyond 4GB so
need to confine this check, otherwise all pages beyond 4GB will be
treated as uncached
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
