A bug exists if the user executes a COUNTER_ADD_WATCH_IOCTL ioctl call,
and then executes a COUNTER_DISABLE_EVENTS_IOCTL ioctl call. Disabling
the events should disable the 104-QUAD-8 interrupts, but because of this
bug the interrupts are not disabling.
The reason this bug is occurring is because quad8_events_configure() is
called when COUNTER_DISABLE_EVENTS_IOCTL is handled, but the
next_irq_trigger[] array has not been cleared before it is checked in
the loop.
This patch fixes the bug by removing the next_irq_trigger array and
instead utilizing a different algorithm of walking the events_list list
for the current requested events. When a COUNTER_DISABLE_EVENTS_IOCTL is
handled, events_list will be empty and thus all device channels end up
with interrupts disabled.
Fixes: 7aa2ba0df6 ("counter: 104-quad-8: Add IRQ support for the ACCES 104-QUAD-8")
Cc: Syed Nayyar Waris <syednwaris@gmail.com>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Link: https://lore.kernel.org/r/5fd5731cec1c251acee30eefb7c19160d03c9d39.1640072891.git.vilhelm.gray@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using counter->priv is a memory read and so more expensive than
container_of which is only an addition. (In this case even a noop
because the offset is 0.)
So container_of is expected to be a tad faster, it's type-safe, and
produces smaller code (ARCH=arm allmodconfig):
$ source/scripts/bloat-o-meter drivers/counter/ti-eqep.o-pre drivers/counter/ti-eqep.o
add/remove: 0/0 grow/shrink: 0/9 up/down: 0/-108 (-108)
Function old new delta
ti_eqep_position_enable_write 132 120 -12
ti_eqep_position_enable_read 260 248 -12
ti_eqep_position_ceiling_write 132 120 -12
ti_eqep_position_ceiling_read 236 224 -12
ti_eqep_function_write 220 208 -12
ti_eqep_function_read 372 360 -12
ti_eqep_count_write 312 300 -12
ti_eqep_count_read 236 224 -12
ti_eqep_action_read 664 652 -12
Total: Before=4598, After=4490, chg -2.35%
Acked-by: David Lechner <david@lechnology.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Link: https://lore.kernel.org/r/4bde7cbd9e43a5909208102094444219d3154466.1640072891.git.vilhelm.gray@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to support nvmem bits property, should support minimum 1 byte
read stride and minimum 1 byte read granularity at the same time.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20211209174235.14049-4-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Return value from ocxl_context_attach() directly instead
of taking this in another redundant variable.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Acked-by: Andrew Donnellan <ajd@linux.ibm.com>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Link: https://lore.kernel.org/r/20211215060438.441918-1-chi.minghao@zte.com.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of invoking a synchronize_rcu() to free a pointer
after a grace period we can directly make use of new API
that does the same but in more efficient way.
Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com>
Link: https://lore.kernel.org/r/20211215111845.2514-6-urezki@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MIPS include files define "PC" so when building the paride driver the
following build warning shows up:
rivers/block/paride/bpck.c:32: warning: "PC" redefined
Fix this by undefining PC before redefining it as is done for other
defines in this driver.
Cc: Tim Waugh <tim@cyberelk.net>
Acked-by: Jens Axboe <axboe@kernel.dk>
Link: https://lore.kernel.org/r/20211130084626.3215987-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The definition of RIO_VID_FREESCALE, RIO_DID_MPC8560, RIO_DID_TSI500,
RIO_DID_TSI576 and RIO_DID_TSI721 are not used for many years in the
current code, so just remove them.
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Link: https://lore.kernel.org/r/1639625581-22867-2-git-send-email-yangtiezhu@loongson.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Explicitly remove the file entries from sysfs before dropping the final
reference for symmetry reasons and for consistency with the rest of the
driver.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211201132528.30025-5-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to always NUL-terminate file names retrieved from the firmware
to avoid accessing data beyond the entry slab buffer and exposing it
through sysfs in case the firmware data is corrupt.
Fixes: 75f3e8e47f ("firmware: introduce sysfs driver for QEMU's fw_cfg device")
Cc: stable@vger.kernel.org # 4.6
Cc: Gabriel Somlo <somlo@cmu.edu>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211201132528.30025-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An initialised kobject must be freed using kobject_put() to avoid
leaking associated resources (e.g. the object name).
Commit fe3c606843 ("firmware: Fix a reference count leak.") "fixed"
the leak in the first error path of the file registration helper but
left the second one unchanged. This "fix" would however result in a NULL
pointer dereference due to the release function also removing the never
added entry from the fw_cfg_entry_cache list. This has now been
addressed.
Fix the remaining kobject leak by restoring the common error path and
adding the missing kobject_put().
Fixes: 75f3e8e47f ("firmware: introduce sysfs driver for QEMU's fw_cfg device")
Cc: stable@vger.kernel.org # 4.6
Cc: Gabriel Somlo <somlo@cmu.edu>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211201132528.30025-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit fe3c606843 ("firmware: Fix a reference count leak.") "fixed"
a kobject leak in the file registration helper by properly calling
kobject_put() for the entry in case registration of the object fails
(e.g. due to a name collision).
This would however result in a NULL pointer dereference when the
release function tries to remove the never added entry from the
fw_cfg_entry_cache list.
Fix this by moving the list-removal out of the release function.
Note that the offending commit was one of the benign looking umn.edu
fixes which was reviewed but not reverted. [1][2]
[1] https://lore.kernel.org/r/202105051005.49BFABCE@keescook
[2] https://lore.kernel.org/all/YIg7ZOZvS3a8LjSv@kroah.com
Fixes: fe3c606843 ("firmware: Fix a reference count leak.")
Cc: stable@vger.kernel.org # 5.8
Cc: Qiushi Wu <wu000273@umn.edu>
Cc: Kees Cook <keescook@chromium.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211201132528.30025-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Static variables do not need to be initialised to 0, because compilers
will initialise all uninitialised statics to 0. Thus, remove the
unneeded initializations.
Signed-off-by: Jason Wang <wangborong@cdjrlc.com>
Link: https://lore.kernel.org/r/20211212071838.304307-1-wangborong@cdjrlc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the sysfs_emit to replace sprintf. sprintf may cause
output defect in sysfs content, it is better to use new
added sysfs_emit function which knows the size of the
temporary buffer.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Link: https://lore.kernel.org/r/20211206104724.11559-1-yekai13@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The double `for' in the comment in line 81 is repeated. Remove one
of them from the comment.
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jason Wang <wangborong@cdjrlc.com>
Link: https://lore.kernel.org/r/20211212031657.41169-1-wangborong@cdjrlc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The help text for GOOGLE_FIRMWARE states that it should only be
enabled when building a kernel for Google's own servers. However,
many of the drivers dependent on it are also useful on Chromebooks or
on any platform using coreboot.
Update the help text to reflect this double duty.
Fixes: d384d6f43d ("firmware: google memconsole: Add coreboot support")
Reviewed-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Link: https://lore.kernel.org/r/20180618225540.GD14131@decadent.org.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
binder.c uses <asm/cacheflush.h> instead of <linux/cacheflush.h>.
Hence change cacheflush header file to proper one.
This change also avoid warning from checkpatch that shown below:
WARNING: Use #include <linux/cacheflush.h> instead of <asm/cacheflush.h>
Signed-off-by: Ajith P V <ajithpv.linux@gmail.com>
Link: https://lore.kernel.org/r/20211215132018.31522-1-ajithpv.linux@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This pull request includes:
- A patch that uses devm_bitmap_zalloc() instead of the open-coded
equivalent.
- Work to make coresight complex configuration loadable via modules.
- Some coresight documentation updates.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
-----BEGIN PGP SIGNATURE-----
iQFPBAABCgA5FiEEeTrpXvBwUkra1RYWo5FxFnwrV6EFAmHAvPMbHG1hdGhpZXUu
cG9pcmllckBsaW5hcm8ub3JnAAoJEKORcRZ8K1ehlWEH/iwrNuNR398iPScMgSpi
fGV1vFkajwAPu69VSl2bgcU9kHAujjG4iabv1ZVd5vDaw4xf3Qzh1qOVhzodF7On
YDLM10UKj5K1pSiCMjWJvPGnlZ77GivBFa3hnvHAoBd6L/Z4k+bgCXxIzI1q7VEY
RG2CS+A9JvVB3BWYbGOWMP35vrbzSPUWvgarFLDynrAXGIixu4GRIFy/5ERrd8Hv
BOlc/0aHfKRaOVLRGVimegqNZmnVYwkTitqYyM+CUew6qIexRoJv2LcfmC31v8uF
x0dxF6Z0KpSUf6q34FzEkN2gMhDWmwEz/qFOP8zfYi587ckKz8UkemF54P2ybol+
IK4=
=xBUr
-----END PGP SIGNATURE-----
Merge tag 'coresight-next-v5.17' of gitolite.kernel.org:pub/scm/linux/kernel/git/coresight/linux into char-misc-next
Mathieu writes:
Coresight changes for v5.17
This pull request includes:
- A patch that uses devm_bitmap_zalloc() instead of the open-coded
equivalent.
- Work to make coresight complex configuration loadable via modules.
- Some coresight documentation updates.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
* tag 'coresight-next-v5.17' of gitolite.kernel.org:pub/scm/linux/kernel/git/coresight/linux:
coresight: core: Fix typo in a comment
Documentation: coresight: Update coresight configuration docs
coresight: configfs: Allow configfs to activate configuration
coresight: syscfg: Example CoreSight configuration loadable module
coresight: syscfg: Update load API for config loadable modules
coresight: configuration: Update API to permit dynamic load/unload
coresight: configuration: Update API to introduce load owner concept
Documentation: coresight: Fix documentation issue
coresight: Use devm_bitmap_zalloc when applicable
Russ' patches rework the way we register FPGA managers, regions and
bridges by simplifying the functions into a single register call.
Nathan's patch addresses an unused variable warning that was introduced
by Russ' patches.
Yang's patch addresses a kernel doc warning.
All patches have been reviewed on the mailing list, and have been in the
last few linux-next releases (as part of our for-next branch) without issues.
Signed-off-by: Moritz Fischer <mdf@kernel.org>
-----BEGIN PGP SIGNATURE-----
iIUEABYIAC0WIQSdhnt2PwibB65UG0C3mJX/Vsn7uQUCYbz4vQ8cbWRmQGtlcm5l
bC5vcmcACgkQt5iV/1bJ+7mdsAEA1wiVjcmpJZGb+3HoMxdLIJGQ+BV341eXpDp3
AYS9Hx4A/i8jZ4YqrFe+v9IgXe6Arq2ePzIW/FpacwijobMBiHQE
=S1TU
-----END PGP SIGNATURE-----
Merge tag 'fpga-for-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mdf/linux-fpga into char-misc-next
Moritz writes:
FPGA Manager changes for 5.17-rc1
Russ' patches rework the way we register FPGA managers, regions and
bridges by simplifying the functions into a single register call.
Nathan's patch addresses an unused variable warning that was introduced
by Russ' patches.
Yang's patch addresses a kernel doc warning.
All patches have been reviewed on the mailing list, and have been in the
last few linux-next releases (as part of our for-next branch) without issues.
Signed-off-by: Moritz Fischer <mdf@kernel.org>
* tag 'fpga-for-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mdf/linux-fpga:
fpga: region: fix kernel-doc
fpga: stratix10-soc: Do not use ret uninitialized in s10_probe()
fpga: region: Use standard dev_release for class driver
fpga: bridge: Use standard dev_release for class driver
fpga: mgr: Use standard dev_release for class driver
There are two different PCIe PHYs on SM8450, one having one lane (v5)
and another with two lanes (v5.20). This commit adds support for the
first PCIe phy only, support for the second PCIe PHY is coming in next
commits.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211214225846.2043361-4-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There are two different PCIe PHYs on SM8450, one having one lane and
another with two lanes. Add DT bindings for the first one. Support for
second PCIe host and PHY will be submitted separately.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211214225846.2043361-3-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The qpnpint_irq_set_type() callback function configures the type
(edge vs level) and polarity (high, low, or both) of a particular
PMIC interrupt within a given peripheral. To do this, it reads
the three consecutive IRQ configuration registers, modifies the
specified IRQ bit within the register values, and finally writes
the three modified register values back to the PMIC. While a
spinlock is used to provide mutual exclusion on the SPMI bus
during the register read and write calls, there is no locking
around the overall read, modify, write sequence. This opens up
the possibility of a race condition if two tasks set the type of
a PMIC IRQ within the same peripheral simultaneously.
When the race condition is encountered, both tasks will read the
old value of the registers and IRQ bits set by one of the tasks
will be dropped upon the register write of the other task. This
then leads to PMIC IRQs being enabled with an incorrect type and
polarity configured. Such misconfiguration can lead to an IRQ
storm that overwhelms the system and causes it to crash.
This race condition and IRQ storm have been observed when using
a pair of pm8941-pwrkey devices to handle PMK8350 pwrkey and
resin interrupts. The independent devices probe asynchronously
in parallel and can simultaneously request and configure PMIC
IRQs in the same PMIC peripheral.
For a good case, the IRQ configuration calls end up serialized
due to timing deltas and the register read/write sequence looks
like this:
1. pwrkey probe: SPMI read(0x1311): 0x00, 0x00, 0x00
2. pwrkey probe: SPMI write(0x1311): 0x80, 0x80, 0x80
3. resin probe: SPMI read(0x1311): 0x80, 0x80, 0x80
4. resin probe: SPMI write(0x1311): 0xC0, 0xC0, 0xC0
The final register states after both devices have requested and
enabled their respective IRQs is thus:
0x1311: 0xC0
0x1312: 0xC0
0x1313: 0xC0
0x1314: 0x00
0x1315: 0xC0
For a bad case, the IRQ configuration calls end up occurring
simultaneously and the race condition is encountered. The
register read/write sequence then looks like this:
1. pwrkey probe: SPMI read(0x1311): 0x00, 0x00, 0x00
2. resin probe: SPMI read(0x1311): 0x00, 0x00, 0x00
3. pwrkey probe: SPMI write(0x1311): 0x80, 0x80, 0x80
4. resin probe: SPMI write(0x1311): 0x40, 0x40, 0x40
In this case, the final register states after both devices have
requested and enabled their respective IRQs is thus:
0x1311: 0x40
0x1312: 0x40
0x1313: 0x40
0x1314: 0x00
0x1315: 0xC0
This corresponds to the resin IRQ being configured for both
rising and falling edges, as expected. However, the pwrkey IRQ
is misconfigured as level type with both polarity high and low
set to disabled. The PMIC IRQ triggering hardware treats this
particular register configuration as if level low triggering is
enabled.
The raw pwrkey IRQ signal is low when the power key is not being
pressed. Thus, the pwrkey IRQ begins firing continuously in an
IRQ storm.
Fix the race condition by holding the spmi-pmic-arb spinlock for
the duration of the read, modify, write sequence performed in the
qpnpint_irq_set_type() function. Split the pmic_arb_read_cmd()
and pmic_arb_write_cmd() functions each into three parts so that
hardware register IO is decoupled from spinlock locking. This
allows a new function pmic_arb_masked_write() to be added which
locks the spinlock and then calls register IO functions to
perform SPMI read and write commands in a single atomic
operation.
Link: https://lore.kernel.org/r/20211118034719.28971-1-quic_collinsd@quicinc.com
Signed-off-by: David Collins <quic_collinsd@quicinc.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20211216190812.1574801-7-sboyd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add spmi support for MT8195.
Refine indent in spmi-mtk-pmif.c.
Link: https://lore.kernel.org/r/20211119034613.32489-5-james.lo@mediatek.com
Acked-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: James Lo <james.lo@mediatek.com>
Signed-off-by: Henry Chen <henryc.chen@mediatek.com>
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20211216190812.1574801-6-sboyd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's useful to know what particular device/component is having trouble
accessing the bus. Add the sid and address to error messages here so
that debugging is a little simpler.
Link: https://lore.kernel.org/r/20210920234849.3614036-1-swboyd@chromium.org
Cc: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
Cc: satya priya <skakit@codeaurora.org>
Reviewed-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
Reviewed-by: Satya Priya <skakit@codeaurora.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20211216190812.1574801-2-sboyd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The find.h APIs are designed to be used only on unsigned long arguments.
This can technically result in a over-read, but it is harmless in this
case. Regardless, fix it to avoid the warning seen under -Warray-bounds,
which we'd like to enable globally:
In file included from ./include/linux/bitmap.h:9,
from ./include/linux/cpumask.h:12,
from ./arch/x86/include/asm/cpumask.h:5,
from ./arch/x86/include/asm/msr.h:11,
from ./arch/x86/include/asm/processor.h:22,
from ./arch/x86/include/asm/cpufeature.h:5,
from ./arch/x86/include/asm/thread_info.h:53,
from ./include/linux/thread_info.h:60,
from ./arch/x86/include/asm/preempt.h:7,
from ./include/linux/preempt.h:78,
from ./include/linux/spinlock.h:55,
from ./include/linux/wait.h:9,
from ./include/linux/wait_bit.h:8,
from ./include/linux/fs.h:6,
from ./include/linux/debugfs.h:15,
from drivers/bus/mhi/core/init.c:7:
drivers/bus/mhi/core/init.c: In function 'to_mhi_pm_state_str':
./include/linux/find.h:187:37: warning: array subscript 'long unsigned int[0]' is partly outside array bounds of 'enum mhi_pm_state[1]' [-Warray-bounds]
187 | unsigned long val = *addr & GENMASK(size - 1, 0);
| ^~~~~
drivers/bus/mhi/core/init.c:80:51: note: while referencing 'state'
80 | const char *to_mhi_pm_state_str(enum mhi_pm_state state)
| ~~~~~~~~~~~~~~~~~~^~~~~
Link: https://lore.kernel.org/r/20211215232446.2069794-1-keescook@chromium.org
[mani: changed the variable name "bits" to "pm_state"]
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20211216081227.237749-10-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a new API "mhi_prepare_for_transfer_autoqueue" for using with client
drivers like QRTR to request MHI core to autoqueue buffers for the DL
channel along with starting both UL and DL channels.
So far, the "auto_queue" flag specified by the controller drivers in
channel definition served this purpose but this will be removed at some
point in future.
Cc: netdev@vger.kernel.org
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Co-developed-by: Loic Poulain <loic.poulain@linaro.org>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20211216081227.237749-9-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During SYS_ERR condition, as a response to the MHI_RESET from host, some
devices tend to issue BHI interrupt without clearing the SYS_ERR state in
the device. This creates a race condition and causes a failure in booting
up the device.
The issue is seen on the Sierra Wireless EM9191 modem during SYS_ERR
handling in mhi_async_power_up(). Once the host detects that the device
is in SYS_ERR state, it issues MHI_RESET and waits for the device to
process the reset request. During this time, the device triggers the BHI
interrupt to the host without clearing SYS_ERR condition. So the host
starts handling the SYS_ERR condition again.
To fix this issue, let's register the IRQ handler only after handling the
SYS_ERR check to avoid getting spurious IRQs from the device.
Fixes: e18d4e9fa7 ("bus: mhi: core: Handle syserr during power_up")
Cc: stable@vger.kernel.org
Reported-by: Aleksander Morgado <aleksander@aleksander.es>
Tested-by: Aleksander Morgado <aleksander@aleksander.es>
Tested-by: Thomas Perrot <thomas.perrot@bootlin.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20211216081227.237749-8-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no reason for shutting down MHI ungracefully on freeze,
this causes the MHI host stack & device stack to not be aligned
anymore since the proper MHI reset sequence is not performed for
ungraceful shutdown.
Link: https://lore.kernel.org/r/1635268180-13699-1-git-send-email-loic.poulain@linaro.org
Fixes: 5f0c2ee1fe ("bus: mhi: pci-generic: Fix hibernation")
Cc: stable@vger.kernel.org
Suggested-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20211216081227.237749-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add new device ID 0xe0bf for T99W175.
This device ID is created because it is using Qualcomm SDX55 new base line.
Test evidence as below:
root@jbd-ThinkPad-P1-Gen-4:/dev# lspci -nn | grep Foxconn
0000:08:00.0 Wireless controller [0d40]: Foxconn International, Inc. Device [105b:e0bf]
root@jbd-ThinkPad-P1-Gen-4:/dev# cat wwan0at0 & echo -ne "ati\r" > wwan0at0
[2] 2977
root@jbd-ThinkPad-P1-Gen-4:/dev# ati
Manufacturer: Qualcomm
Model: T99W175
Revision: T99W175.F0.6.0.0.6.CC.005 1 [Oct 21 2021 10:00:00]
IMEI:
+GCAP: +CGSM
OK
Link: https://lore.kernel.org/r/20211029104918.3976-1-slark_xiao@163.com
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Slark Xiao <slark_xiao@163.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20211216081227.237749-2-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Fix printk() usage during recursion (Ard Biesheuvel)
- Fix rodata section to actually have contents (Christophe Leroy)
- Add notes about lkdtm_kernel_info usage (Kees Cook)
- Avoid stack-entropy selftest when LKDTM is disabled (Misono Tomohiro)
-----BEGIN PGP SIGNATURE-----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=JLZP
-----END PGP SIGNATURE-----
Merge tag 'lkdtm-v5.17-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/kees/linux into char-misc-next
Kees writes:
lkdtm updates for v5.17-rc1
- Fix printk() usage during recursion (Ard Biesheuvel)
- Fix rodata section to actually have contents (Christophe Leroy)
- Add notes about lkdtm_kernel_info usage (Kees Cook)
- Avoid stack-entropy selftest when LKDTM is disabled (Misono Tomohiro)
* tag 'lkdtm-v5.17-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
selftest/lkdtm: Skip stack-entropy test if lkdtm is not available
lkdtm: Fix content of section containing lkdtm_rodata_do_nothing()
lkdtm: avoid printk() in recursive_loop()
lkdtm: Note that lkdtm_kernel_info should be removed in the future
On a kernel without CONFIG_STRICT_KERNEL_RWX, running EXEC_RODATA
test leads to "Illegal instruction" failure.
Looking at the content of rodata_objcopy.o, we see that the
function content zeroes only:
Disassembly of section .rodata:
0000000000000000 <.lkdtm_rodata_do_nothing>:
0: 00 00 00 00 .long 0x0
Add the contents flag in order to keep the content of the section
while renaming it.
Disassembly of section .rodata:
0000000000000000 <.lkdtm_rodata_do_nothing>:
0: 4e 80 00 20 blr
Fixes: e9e08a0738 ("lkdtm: support llvm-objcopy")
Cc: stable@vger.kernel.org
Cc: Kees Cook <keescook@chromium.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/8900731fbc05fb8b0de18af7133a8fc07c3c53a1.1633712176.git.christophe.leroy@csgroup.eu
