A large part of the arm-soc patches are nowadays DT changes, adding support
for new SoCs, boards and devices without changing kernel source. The plan
is still to move the devicetree files out of the kernel tree and reduce
the amount of churn going on here, but we keep finding reasons to delay
doing that.
Changes are really all over the place, with little sticking out particularly.
We have contributions from a total of 116 people in this branch.
Unfortunately, the size of this branch also causes a significant number
of conflicts at the moment, typically when subsystem maintainers merge
patches that change the driver at the same time as the dts files. In
most cases this could be avoided because the dts changes are supposed
to be compatible in both ways, and we are asking everyone to send ARM
dts changes through our tree only.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=zl/N
-----END PGP SIGNATURE-----
Merge tag 'dt-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree changes from Arnd Bergmann:
"A large part of the arm-soc patches are nowadays DT changes, adding
support for new SoCs, boards and devices without changing kernel
source. The plan is still to move the devicetree files out of the
kernel tree and reduce the amount of churn going on here, but we keep
finding reasons to delay doing that.
Changes are really all over the place, with little sticking out
particularly. We have contributions from a total of 116 people in
this branch.
Unfortunately, the size of this branch also causes a significant
number of conflicts at the moment, typically when subsystem
maintainers merge patches that change the driver at the same time as
the dts files. In most cases this could be avoided because the dts
changes are supposed to be compatible in both ways, and we are asking
everyone to send ARM dts changes through our tree only"
* tag 'dt-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (541 commits)
dts: stmmac: Document the clocks property in the stmmac base document
dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac.
ARM: STi: stih41x: Add support for the FSM Serial Flash Controller
ARM: STi: stih416: Add support for the FSM Serial Flash Controller
ARM: tegra: fix Dalmore pinctrl configuration
ARM: dts: keystone: use common "ti,keystone" compatible instead of -evm
ARM: dts: k2hk-evm: set ubifs partition size for 512M NAND
ARM: dts: Build all keystone dt blobs
ARM: dts: keystone: Fix control register range for clktsip
ARM: dts: keystone: Fix domain register range for clkfftc1
ARM: dts: bcm28155-ap: leave camldo1 on to fix reboot
ARM: dts: add bcm590xx pmu support and enable for bcm28155-ap
ARM: dts: bcm21664: Add device tree files.
ARM: DT: bcm21664: Device tree bindings
ARM: efm32: properly namespace i2c location property
ARM: efm32: fix unit address part in USART2 device nodes' names
ARM: mvebu: Enable NAND controller in Armada 385-DB
ARM: mvebu: Add support for NAND controller in Armada 38x SoC
ARM: mvebu: Add the Core Divider clock to Armada 38x SoCs
ARM: mvebu: Add a 2 GHz fixed-clock on Armada 38x SoCs
...
Pull irq code updates from Thomas Gleixner:
"The irq department proudly presents:
- Another tree wide sweep of irq infrastructure abuse. Clear winner
of the trainwreck engineering contest was:
#include "../../../kernel/irq/settings.h"
- Tree wide update of irq_set_affinity() callbacks which miss a cpu
online check when picking a single cpu out of the affinity mask.
- Tree wide consolidation of interrupt statistics.
- Updates to the threaded interrupt infrastructure to allow explicit
wakeup of the interrupt thread and a variant of synchronize_irq()
which synchronizes only the hard interrupt handler. Both are
needed to replace the homebrewn thread handling in the mmc/sdhci
code.
- New irq chip callbacks to allow proper support for GPIO based irqs.
The GPIO based interrupts need to request/release GPIO resources
from request/free_irq.
- A few new ARM interrupt chips. No revolutionary new hardware, just
differently wreckaged variations of the scheme.
- Small improvments, cleanups and updates all over the place"
I was hoping that that trainwreck engineering contest was a April Fools'
joke. But no.
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (68 commits)
irqchip: sun7i/sun6i: Disable NMI before registering the handler
ARM: sun7i/sun6i: dts: Fix IRQ number for sun6i NMI controller
ARM: sun7i/sun6i: irqchip: Update the documentation
ARM: sun7i/sun6i: dts: Add NMI irqchip support
ARM: sun7i/sun6i: irqchip: Add irqchip driver for NMI controller
genirq: Export symbol no_action()
arm: omap: Fix typo in ams-delta-fiq.c
m68k: atari: Fix the last kernel_stat.h fallout
irqchip: sun4i: Simplify sun4i_irq_ack
irqchip: sun4i: Use handle_fasteoi_irq for all interrupts
genirq: procfs: Make smp_affinity values go+r
softirq: Add linux/irq.h to make it compile again
m68k: amiga: Add linux/irq.h to make it compile again
irqchip: sun4i: Don't ack IRQs > 0, fix acking of IRQ 0
irqchip: sun4i: Fix a comment about mask register initialization
irqchip: sun4i: Fix irq 0 not working
genirq: Add a new IRQCHIP_EOI_THREADED flag
genirq: Document IRQCHIP_ONESHOT_SAFE flag
ARM: sunxi: dt: Convert to the new irq controller compatibles
irqchip: sunxi: Change compatibles
...
Pull timer changes from Thomas Gleixner:
"This assorted collection provides:
- A new timer based timer broadcast feature for systems which do not
provide a global accessible timer device. That allows those
systems to put CPUs into deep idle states where the per cpu timer
device stops.
- A few NOHZ_FULL related improvements to the timer wheel
- The usual updates to timer devices found in ARM SoCs
- Small improvements and updates all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (44 commits)
tick: Remove code duplication in tick_handle_periodic()
tick: Fix spelling mistake in tick_handle_periodic()
x86: hpet: Use proper destructor for delayed work
workqueue: Provide destroy_delayed_work_on_stack()
clocksource: CMT, MTU2, TMU and STI should depend on GENERIC_CLOCKEVENTS
timer: Remove code redundancy while calling get_nohz_timer_target()
hrtimer: Rearrange comments in the order struct members are declared
timer: Use variable head instead of &work_list in __run_timers()
clocksource: exynos_mct: silence a static checker warning
arm: zynq: Add support for cpufreq
arm: zynq: Don't use arm_global_timer with cpufreq
clocksource/cadence_ttc: Overhaul clocksource frequency adjustment
clocksource/cadence_ttc: Call clockevents_update_freq() with IRQs enabled
clocksource: Add Kconfig entries for CMT, MTU2, TMU and STI
sh: Remove Kconfig entries for TMU, CMT and MTU2
ARM: shmobile: Remove CMT, TMU and STI Kconfig entries
clocksource: armada-370-xp: Use atomic access for shared registers
clocksource: orion: Use atomic access for shared registers
clocksource: timer-keystone: Delete unnecessary variable
clocksource: timer-keystone: introduce clocksource driver for Keystone
...
- Two new boards: INet 97F Rev 02 and A10-OLinuXino-LIME
- Addition of the I2C for the A31
- Addition USB Host mode for the A10, A10s, A13 and A20
- Addition of SATA support for the A10 and A20
- Change of compatible for the watchdog
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=8O2D
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-3.15-2' of https://github.com/mripard/linux into next/dt
Pull "Allwinner DT additions for 3.15, take 2" from Maxime Ripard:
- Two new boards: INet 97F Rev 02 and A10-OLinuXino-LIME
- Addition of the I2C for the A31
- Addition USB Host mode for the A10, A10s, A13 and A20
- Addition of SATA support for the A10 and A20
- Change of compatible for the watchdog
* tag 'sunxi-dt-for-3.15-2' of https://github.com/mripard/linux: (23 commits)
ARM: sunxi: dt: Update the watchdog compatibles
ARM: sun6i: colombus: Enable the I2C controllers
ARM: sun6i: Enable the I2C muxing options
ARM: sun6i: Enable the I2C controllers
ARM: sun4i: dt: Add support for the INet-97F_Rev_02 board
ARM: sun4i: dt: Add support for the A10-OLinuXino-LIME board
ARM: sun7i: dt: Add USB host nodes to a20-olinuxino-micro dts
ARM: sun7i: dt: Add USB host nodes to cubieboard2 dts
ARM: sun7i: dt: Add USB host nodes to cubietruck dts
ARM: sun5i: dt: Add USB host nodes to a13-olinuxino-micro
ARM: sun5i: dt: Add USB host nodes to a10s-olinuxino-micro
ARM: sun5i: dt: Add USB host nodes to A13-Olinuxino
ARM: sun4i: dt: Add USB host nodes to pcduino.dts
ARM: sun4i: dt: Add USB host nodes to mini-xplus dts
ARM: sun4i: dt: Add USB host nodes to hackberry dts
ARM: sun4i: dt: Add USB host nodes to cubieboard dts
ARM: sun4i: dt: Add USB host nodes to Mele A1000 dts
ARM: sun7i: dt: Add USB host bindings
ARM: sun5i: dt: Add USB host bindings
ARM: sun4i: dt: Add USB host bindings
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The watchdog compatibles were following a different pattern than the one found
in the other devices. Now that the driver supports the right pattern, switch to
it in the DT.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Switch the device tree to the new compatibles introduced in the timer driver
to have a common pattern accross all Allwinner SoCs.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
interrupt types of some IPs, the other fixes up a compatible that got
introduced during 3.14
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIcBAABAgAGBQJTFFXwAAoJEBx+YmzsjxAgXR4P/3Oa9crjF3IFZq4ugO+cJsbg
F3xjKMfuyCjfAYwtzexivRl7PjuGShdevYvNRbY1sqNTAIQbJRWAQC+ZXolXPp/W
gE6z8mAIlLG0OmE8t1glGLhXVyXiRTlm2s96su2q73MWqYMNXE+yr8K+qt+5gA7r
M34lYAGqKyQEgs8TKSGSvqa7yZLWZlii6FKwtOCU6HlFm3Rz9Glj8MyTixQDMY0H
LCONp9csbEgPfrLh+FfJitK2H5kRAU0xJAmP/k+rZtzSKy0kPuCTsKO/ZeUnKhQy
Rq1Li60Ho3nzmVNljtFVPoDZluxlrZwXA8xLzE88CiwjlYx3TauFFxIIbyGwPamX
hBEWDqL0x9Y7FQD4Ft4s8mnCE1bD+7eKnqCyCDVGD5je+1qu70vFQZa7ZR2eM9kg
FS/GSWuG54nIBRwIn7tcdK6iKxkvOIq9ZyQIYw5Uk0d2ZYeiyWNnHl9KtfjwKkXN
Yh2N6yd4tH6gUhH9niHyczumTuya4+QUbd8DxZrbkD9G3XnmQdLbjTifAjvZTzk/
zRF/nx399aEYd2LHoBpozuhF9k8otrleC8sWqIjkwVRVX9KYsgNC2CuIgUQCgSpX
hFcx1xtdNwFyq3AdZmrSV1ORBumEb3lhNAtXWwtFfioamDWDIb2m39wgxiNhZrN7
hdpJ2Rt48dI8iTRKRxQ9
=uxIH
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-3.14' of https://github.com/mripard/linux into fixes
Allwinner fixes from Maxime Ripard:
Two fixes for device trees additions that got added in 3.14. One fixes the
interrupt types of some IPs, the other fixes up a compatible that got
introduced during 3.14
* tag 'sunxi-fixes-for-3.14' of https://github.com/mripard/linux:
ARM: sunxi: dt: Change the touchscreen compatibles
ARM: sun7i: dt: Fix interrupt trigger types
Signed-off-by: Olof Johansson <olof@lixom.net>
Add nodes for the usb-phy and ehci- and ohci-usb-host controllers.
Signed-off-by: Roman Byshko <rbyshko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch adds sunxi sata support to A20 boards that have such a connector.
Some boards also feature a regulator via a GPIO and support for this is also
added.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A20 has 4 SPI controllers compatible with the one found in the A10. Add
them in the DT.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Switch the device tree to the new compatibles introduced in the clock drivers
to have a common pattern accross all Allwinner SoCs.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Allwinner A20 SoC is built around a pair of Cortex-A7 cores,
which have the usual generic timers. Report this in the DT.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Roman Byshko <rbyshko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
All Allwinner A20 boards we support can only use either EMAC or GMAC,
as they share the same pins. As we have switched all supported to
GMAC, we should alias GMAC (the active controller) as ethernet0,
so u-boot will insert the MAC address for the correct controller.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A20 has EMAC and GMAC muxed on the same pins.
Add pin sets with gmac function for MII and RGMII mode to the DTSI.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The GMAC uses 1 of 2 sources for its transmit clock, depending on the
PHY interface mode. Add both sources as dummy clocks, and as parents
to the GMAC clock node.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Switch the device tree touchscreen compatibles to have a common pattern accross
all Allwinner SoCs. Since the touchscreen driver has not been merged yet, it
has no side effect.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Allwinner A20 uses the ARM GIC as its internal interrupts controller. The
GIC can work on several interrupt triggers, and the A20 was actually setting it
up to use a rising edge as a trigger, while it was actually a level high
trigger, leading to some interrupts that would be completely ignored if the
edge was missed.
Fix this for the remaining DT nodes that slipped through.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: stable@vger.kernel.org
Device tree naming conventions state that node names should match
node function. Change fully functioning clock nodes to match and
add clock-output-names to all sunxi clock nodes.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Switch the device tree to the new compatibles introduced in the ethernet and
mdio drivers to have a common pattern accross all Allwinner SoCs.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
UART2 is used on CubieTruck to connect to the Bluetooth module.
Add the pin set used in this case.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some UART aliases have been defined, but not all of them. Add the remaining
ones to be consistent and to ease the parsing of the DT by the bootloaders.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
DT and DT-conversion-related changes for various ARM platforms. Most
of these are to enable various devices on various boards, etc, and not
necessarily worth enumerating.
New boards and systems continue to come in as new devicetree files that
don't require corresponding C changes any more, which is indicating that
the system is starting to work fairly well.
A few things worth pointing out:
* ST Ericsson ux500 platforms have made the major push to move over to fully
support the platform with DT.
* Renesas platforms continue their conversion over from legacy platform devices
to DT-based for hardware description.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=4o2d
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Olof Johansson:
"DT and DT-conversion-related changes for various ARM platforms. Most
of these are to enable various devices on various boards, etc, and not
necessarily worth enumerating.
New boards and systems continue to come in as new devicetree files
that don't require corresponding C changes any more, which is
indicating that the system is starting to work fairly well.
A few things worth pointing out:
* ST Ericsson ux500 platforms have made the major push to move over
to fully support the platform with DT
* Renesas platforms continue their conversion over from legacy
platform devices to DT-based for hardware description"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (327 commits)
ARM: dts: SiRF: add pin group for USP0 with only RX or TX frame sync
ARM: dts: SiRF: add lost usp1_uart_nostreamctrl pin group for atlas6
ARM: dts: sirf: add lost minigpsrtc device node
ARM: dts: sirf: add clock, frequence-voltage table for CPU0
ARM: dts: sirf: add lost bus_width, clock and status for sdhci
ARM: dts: sirf: add lost clocks for cphifbg
ARM: dts: socfpga: add pl330 clock
ARM: dts: socfpga: update L2 tag and data latency
arm: sun7i: cubietruck: Enable the i2c controllers
ARM: dts: add support for EXYNOS4412 based TINY4412 board
ARM: dts: Add initial support for Arndale Octa board
ARM: bcm2835: add USB controller to device tree
ARM: dts: MSM8974: Add MMIO architected timer node
ARM: dts: MSM8974: Add restart node
ARM: dts: sun7i: external clock outputs
ARM: dts: sun7i: Change 32768 Hz oscillator node name to clk@N style
ARM: dts: sun7i: Add pin muxing options for clock outputs
ARM: dts: sun7i: Add rtp controller node
ARM: dts: sun5i: Add rtp controller node
ARM: dts: sun4i: Add rtp controller node
...
Pull clocksource/clockevent updates from Daniel Lezcano:
* Axel Lin removed an unused structure defining the ids for the
bcm kona driver.
* Ezequiel Garcia enabled the timer divider only when the 25MHz
timer is not used for the armada 370 XP.
* Jingoo Han removed a pointless platform data initialization for
the sh_mtu and sh_mtu2.
* Laurent Pinchart added the clk_prepare/clk_unprepare for sh_cmt.
* Linus Walleij added a useful warning in clk_of when no clocks
are found while the old behavior was to silently hang at boot time.
* Maxime Ripard added the high speed timer drivers for the
Allwinner SoCs (A10, A13, A20). He increased the rating, shared the
irq across all available cpus and fixed the clockevent's irq
initialization for the sun4i.
* Michael Opdenacker removed the usage of the IRQF_DISABLED for the
all the timers driver located in drivers/clocksource.
* Stephen Boyd switched to sched_clock_register for the
arm_global_timer, cadence_ttc, sun4i and orion timers.
Conflicts:
drivers/clocksource/clksrc-of.c
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This commit adds the two external clock outputs available on A20 to
its device tree. A dummy fixed factor clock is also added to serve as
the first input of the clock outputs, which according to AW's A20 user
manual, is the 24MHz oscillator divided by 750.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Device tree naming conventions state that node names should match
the nodes function. Change external low speed oscillator node name
to match.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch adds the clock output pin options on the A20.
The 2 pins can output a configurable clock to be used by
external modules. This is used on the CubieTruck, to supply
a 32768 Hz low power clock to the onboard Wifi+BT module.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Allwinner sunXi SoCs DT changes for clocks
This contains the DT parts of the "[PATCH v3 00/13] clk: sunxi: add PLL5
and PLL6 support" series. It adds DT nodes for PLL4/5/6 and mod0 clocks
on most sunxi platforms.
mbus is the memory bus clock, and it is present on both sun5i and sun7i
machines. Its register layout is compatible with the mod0 one.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This commit adds all the mod0 clocks available on A20 to its device
tree. This list was created by looking at AW's code release.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This commit adds PLL5 and PLL6 nodes to the sun4i, sun5i and sun7i
device trees.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This commit adds the PLL4 definition to the sun4i, sun5i and sun7i
device trees. PLL4 is compatible with PLL1.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Allwinner A20 uses the ARM GIC as its internal interrupts controller. The
GIC can work on several interrupt triggers, and the A20 was actually setting it
up to use a rising edge as a trigger, while it was actually a level high
trigger, leading to some interrupts that would be completely ignored if the
edge was missed.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Cc: stable@vger.kernel.org #3.12+
Signed-off-by: Olof Johansson <olof@lixom.net>
The Allwinner A20 has support for four high speed timers. Apart for the
number of timers (4 vs 2), it's basically the same logic than the high
speed timers found in the sun5i chips.
Now that we have a driver to support it, we can enable them in the
device tree.
[dlezcano] : Fixed conflict with 428abbb8 "Enable the I2C controllers"
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
U-Boot uses the ethernet0 alias to locate the right node to fill in
the MAC address of the first ethernet interface. This patch adds the
alias on all the sunxi SoCs with EMAC. In this way, people using
ethernet in U-Boot (eg, for tftp) can keep a consistent address on both
U-Boot and Linux with no additional effort.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add the RTC node to DTS for Allwinner A10 and Allwinner A20.
Signed-off-by: Carlo Caione <carlo.caione@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A20 boards we currently have share the same pins for the i2c
controllers they share. Add them to the DTSI.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Allwinner A20 shares the same I2C controller than the one that could
be found on earlier SoCs from Allwinner. There is only a few more of
these controllers. Add all of them in the DTSI.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch shall add support for the sunxi-sid driver to the device
tree for A10, A10s, A13 and A20.
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A20 has several muxing options for the EMAC. Yet, the currently
supported boards only use one set of them. Add that pin set to the DTSI.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The Allwinner A20 SoC also have the EMAC found on the A10 and A10s.
Enable the support for it in the DTSI.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Now that the clock driver knows about the available clocks found on the
A20, we can build up the clock tree from the device tree.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The UARTs on the A20 can be muxed to several pins. Add a few options to
the DTSI so that we can start using them in the boards' DT.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The PIO controller is responsible for the GPIO/muxing/external
interrupts handling. Now that we have support for the A20 pin set in the
pinctrl driver, we can start using it in the DTSI.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Allwinner A20 SoC is based on 2 Cortex A7, an ARM Mali GPU, and is
built to be pin-compatible with the older Allwinner A10.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
