According to the R-Car Gen3 Hardware Manual Errata for Rev 0.80 of Dec
22, 2017, and the Errata for Rev 1.50 of Dec 25, 2018, MOD_SEL0 register
bits 3, 4, 17, and 18 are renamed from SEL_ADG_{A,B,C} to
SEL_ADG{A,B,C}. Update the pin control drivers to reflect this.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.50 of
Feb 12, 2019, the RTS{0,1,3,4}_#/TANS pin names defined in the GPSR and
IPSR registers are renamed to RTS{0,1,3,4}_#.
This patch updates the pin control drivers to reflect this.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Update R-Car H3 ES1.x, V3M, V3H, and D3]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.00 of
Jun 4, 2018, the CC5_OSCOUT pin is removed. Update the pin control
drivers to reflect this.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Update R-Car V3M, V3H]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The HDMI CEC function is not supported by the R-Car Gen3 Hardware Manual
Rev 1.00. Therefore, delete the corresponding pin groups and functions,
and rename the HDMI[01]_CEC definitions to match their GPIO
functionality.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Squashed several commits]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.00 of Aug
24, 2018, there is no need to configure MOD_SEL1 bit30 when the
SSI_SCK2_{A,B} or SSI_WS2_{A,B} pin functions are selected.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Remove now unused definitions, mark MOD_SEL1 bit30 reserved]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.00 of
Aug 24, 2018, there is no need to configure MOD_SEL1 bit31 when the
SIM0_D_{A,B} pin function is selected.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Remove now unused definitions, mark MOD_SEL1 bit31 reserved]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.00 of Aug
24, 2018, the MOD_SEL0 bit16 must be set to 0 when the NFALE_A and
NFRB_N_A pin functions are selected.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
- The IPSR field is meant for documentation only,
- The function name refers to the pin function, not to the IPSR
field.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Add a run-time check to the PINMUX_CFG_REG_VAR() macro, to ensure the
number of provided enum IDs is correct. This cannot be done at build
time, as the number of values depends on the variable-width fields in
the config register.
This helps catching bugs early.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add build-time checks to the PINMUX_CFG_REG() and PINMUX_DATA_REG()
macros, to ensure the number of provided enum IDs is correct.
This helps catching bugs early.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Currently the PINMUX_DATA_REG() macro must be followed by initialization
data, specifying all enum IDs. Hence the macro itself does not know
anything about the enum IDs, preventing the macro from performing any
validation on it.
Make the macro accept the enum IDs as a parameter, and update all users.
Note that array data enclosed by curly braces cannot be passed to a
macro as a parameter, hence the enum IDs are wrapped using the GROUP()
macro.
No functional changes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Currently the PINMUX_CFG_REG_VAR() macro must be followed by
initialization data, specifying all enum IDs. Hence the macro itself
does not know anything about the enum IDs, preventing the macro from
performing any validation on it.
Make the macro accept the enum IDs as a parameter, and update all users.
Note that array data enclosed by curly braces cannot be passed to a
macro as a parameter, hence both the register field widths and the enum
IDs are wrapped using the GROUP() macro.
No functional changes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Currently the PINMUX_CFG_REG() macro must be followed by initialization
data, specifying all enum IDs. Hence the macro itself does not know
anything about the enum IDs, preventing the macro from performing any
validation on it.
Make the macro accept the enum IDs as a parameter, and update all users.
Note that array data enclosed by curly braces cannot be passed to a
macro as a parameter, hence the enum IDs are wrapped using a new macro
GROUPS().
No functional changes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Enable compile-testing of all Renesas SuperH and ARM pin control
drivers, in a similar way as was done before for clock and SoC drivers
in commits 371dd373c6 ("clk: renesas: Allow compile-testing of all
(sub)drivers") and 8be381a131 ("soc: renesas: Rework Kconfig and
Makefile logic").
The SuperH pin control drivers need specific include files, hence make
sure they are always found when compile-testing.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Source files using -Exxx error codes should include <linux/errno.h>.
On ARM, this header file is included indirectly; on SuperH, it is not,
leading to "error: ‘EINVAL’ undeclared" failures when enabling
compile-testing later.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Pinctrl drivers for SuperH platforms use legacy function GPIOs.
Currently this support is compiled in based on the SUPERH platform
dependency, which hinders the introduction of compile-testing support
for the affected pinctrl drivers.
Introduce a new Kconfig symbol PINCTRL_SH_FUNC_GPIO, which is
auto-selected when needed. This symbol in turn selects
PINCTRL_SH_PFC_GPIO, to reduce the number of per-driver selects.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Perform some basic sanity checks on all built-in pinmux tables when
DEBUG is defined, to help catching bugs early.
For now the following checks are included:
- Check register and field widths in descriptors for config registers
with variable-width fields,
- Check relations between pin groups and functions:
- All pin functions must refer to existing pin groups,
- All pin groups must be referred to by a pin function,
- Warn if a pin group is referred to by multiple pin functions
(which is OK for backwards-compatibility aliases),
- Provide suggestions for reducing table sizes: reserved fields of
more than 3 bits can better be split in smaller subfields, as the
storage need is proportional to the square of the width of the
(sub)field,
Note that a dummy non-matching entry is added to the DT match table for
checking r8a7795es1_pinmux_info, as R-Car H3 ES1.0 is matched using
soc_device_match() in r8a7795_pinmux_init(), instead of by the DT match
table.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The TDSELCTRL register is responsible for configuring the SDHI/MMC clock
return path delay and may be adjusted by the bootloader. Retain the value
across suspend/resume to prevent hardware instability after resume.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
CANFD is found also on the R8A774C0, therefore move CANFD pin
groups and functions to "common".
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
CANFD is found also on the R8A774A1, therefore move CANFD pin
groups and functions to "common".
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Adds HSCIF0 and HSCIF1 pins, groups and functions for R8A7779.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The R-Car Gen3 HardWare Manual Errata for Rev. 1.00 (Jul 2, 2018)
renamed the various miscellaneous I/O control registers (IOCTRLx) on
R-Car E3, to reflect better their actual purposes, and matching other
SoCs.
Update the code to match this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
The R-Car Gen3 HardWare Manual Errata for Rev. 1.00 (Jul 2, 2018)
renamed the various miscellaneous I/O control registers (IOCTRLx) on
R-Car V3H, to reflect better their actual purposes, and matching other
SoCs.
Update the code to match this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
The R-Car Gen3 HardWare Manual Errata for Rev. 1.00 (Jul 2, 2018)
renamed the various miscellaneous I/O control registers (IOCTRLx) on
R-Car V3M, to reflect better their actual purposes, and matching other
SoCs.
Update the code to match this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
This patch adds DRIF{0,1,2,3} pins, groups and functions to the R8A77965
SoC.
Based on a similar patch of the R8A7796 PFC driver
by Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds TMU TCLK{1,2} pins, groups and functions to
the R8A77965 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add a build-time check, to ensure the register and field widths in
descriptors for config registers with fixed-width fields are sane.
This helps catching bugs early.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
There are two pin groups for the FSIC SPDIF signal, but the FSIC pin
group array lists only one, and it refers to a nonexistent group.
Fixes: 2ecd4154c9 ("sh-pfc: sh73a0: Add FSI pin groups and functions")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The vin1_data18_b pin group itself is present, but it is not listed in
the VIN1 pin group array, and thus cannot be selected.
Fixes: 7dd74bb1f0 ("pinctrl: sh-pfc: r8a7792: Add VIN pin groups")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The entry for "scifb2_data_c" in the SCIFB2 pin group array contains a
typo, thus the group cannot be selected.
Fixes: 5088451962 ("pinctrl: sh-pfc: r8a7791 PFC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The err_rst_reqb, ext_clki, lowpwr, and ref_clko pin groups are present,
but no pinmux functions refer to them, hence they can not be selected.
Fixes: 1e7d5d849c ("sh-pfc: Add emev2 pinmux support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds DRIF{0,1,2,3} pins, groups and functions to the R8A77990
SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
When declaring the HSPI RX1_B and TX1_B pins, two mistakes were made:
- the rows and columns in the BGA pin matrix, from which the pin
numbers are derived, were exchanged,
- it was not taken into account that pin row labelling skips
characters I, O, Q, and S.
Fix the order, and the corresponding pin names.
Notes:
- The actual values of the pin numbers don't really matter (they just
have to be unique), so the wrong order didn't have any impact,
- Changing the names of the pins is user-visible, but there are no
users in (upstream) DTS files.
Fixes: 4f82e3ee72 ("sh-pfc: Support pins not associated with a GPIO port")
Fixes: 09cc76a958 ("sh-pfc: r8a7778: add HSPI pin groups")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds TMU TCLK{1,2} pins, groups and functions to
the R8A77990 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Unlike R-Car M3-W, R-Car M3-N does not have DU_DOTCLKIN2, but the
corresponding pin carries the DU_DOTCLKIN3 signal. Correct all
references to DU_DOTCLKIN2 to fix this.
This change does not have any runtime effect, as it only changes an
internal enum name, and a comment.
Fixes: 490e687eb8 ("pinctrl: sh-pfc: Initial R-Car M3-N support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The naming of the "b" versions of the VIN1 pin groups is a bit odd, in
that the "_b" appears in the middle of the names, instead of as a
suffix.
Increase consistency with other SoCs by making R-Car M2-W and M2-N, and
RZ/G1M and RZ/G1N, use the recently added optional "version" argument of
the VIN_DATA_PIN_GROUP() macro.
Note that this breaks backwards compatibility with existing DTBs, but
there are no upstream users of the "vin1_b_*" names.
Fixes: 8e32c9671f ("pinctrl: sh-pfc: r8a7791: Add VIN pins")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Use union vin_data12 and VIN_DATA_PIN_GROUP() to reduce redundancies in
pin definitions for the VIN1 channel.
This reduces kernel size by 144 bytes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Use union vin_data12 and VIN_DATA_PIN_GROUP() to reduce redundancies in
pin definitions for the VIN0 and VIN1 channels.
This reduces kernel size by 288 bytes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Use union vin_data16 and VIN_DATA_PIN_GROUP() to reduce redundancies in
pin definitions for the VIN5 channel.
This reduces kernel size by 240 bytes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Use union vin_data16 and VIN_DATA_PIN_GROUP() to reduce redundancies in
pin definitions for the VIN5 channel.
This reduces kernel size by 240 bytes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Documentation for ES1.0 says that some bits in TDSEL must be set (ch
5.3.35 in R-Car E2 v0.5). However, the reset value of the register is 0,
so software has to do it. Add this to the kernel driver to ensure this
is really done independent of firmware versions and use whitelisting for
ES versions known to need this.
This is needed for some SD cards supporting SDR104 transfer mode.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Documentation for ES1.0 says that some bits in TDSEL must be set (ch
5.3.39 in R-Car H2 v0.91). However, the reset value of the register is
0, so software has to do it. Add this to the kernel driver to ensure
this is really done independent of firmware versions and use
whitelisting for ES versions known to need this.
This is needed for some SD cards supporting SDR104 transfer mode. For
me, TDSEL was not initialized by the firmware and I had problems with
the card when re-inserting it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Knowing which pin group is being configured is useful information when
debugging pin configuration.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
This reverts commit f4caa6ee73.
The same can be expressed better by dropping the
SH_PFC_PIN_CFG_PULL_DOWN flag from the GPIO description, as it includes
returning an error to the caller when trying to configure the pin for
pull-down, causing:
sh-pfc e6060000.pin-controller: pin_config_set op failed for pin 201
sh-pfc e6060000.pin-controller: Error applying setting, reverse things back
sh-pfc e6060000.pin-controller: failed to select default state
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
MOD_SEL register bit numbering was different from R-Car D3 SoC and
R-Car H3/M3-[WN] SoCs.
MOD_SEL 1-bit H3/M3-[WN] D3
=============== ========== =====
Set Value = H'0 b'0 b'0
Set Value = H'1 b'1 b'1
MOD_SEL 2-bits H3/M3-[WN] D3
=============== ========== =====
Set Value = H'0 b'00 b'00
Set Value = H'1 b'01 b'10
Set Value = H'2 b'10 b'01
Set Value = H'3 b'11 b'11
MOD_SEL 3-bits H3/M3-[WN] D3
=============== ========== =====
Set Value = H'0 b'000 b'000
Set Value = H'1 b'001 b'100
Set Value = H'2 b'010 b'010
Set Value = H'3 b'011 b'110
Set Value = H'4 b'100 b'001
Set Value = H'5 b'101 b'101
Set Value = H'6 b'110 b'011
Set Value = H'7 b'111 b'111
This patch replaces the #define name and value of MOD_SEL.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Fixes: 794a671176 ("pinctrl: sh-pfc: Initial R8A77995 PFC support")
[shimoda: split a patch per SoC and revise the commit log]
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
[geert: Use a macro to do the actual reordering]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
MOD_SEL register bit numbering was different from R-Car E3 SoC and
R-Car H3/M3-[WN] SoCs.
MOD_SEL 1-bit H3/M3-[WN] E3
=============== ========== =====
Set Value = H'0 b'0 b'0
Set Value = H'1 b'1 b'1
MOD_SEL 2-bits H3/M3-[WN] E3
=============== ========== =====
Set Value = H'0 b'00 b'00
Set Value = H'1 b'01 b'10
Set Value = H'2 b'10 b'01
Set Value = H'3 b'11 b'11
MOD_SEL 3-bits H3/M3-[WN] E3
=============== ========== =====
Set Value = H'0 b'000 b'000
Set Value = H'1 b'001 b'100
Set Value = H'2 b'010 b'010
Set Value = H'3 b'011 b'110
Set Value = H'4 b'100 b'001
Set Value = H'5 b'101 b'101
Set Value = H'6 b'110 b'011
Set Value = H'7 b'111 b'111
This patch replaces the #define name and value of MOD_SEL.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Fixes: 6d4036a1e3 ("pinctrl: sh-pfc: Initial R8A77990 PFC support")
[shimoda: Split a patch per SoC and revise the commit log]
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
[geert: Use macros to do the actual reordering]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.00 of
Aug 24, 2018, the MOD_SEL0 bit2 is set when RX2_{A,B}, TX2_{A,B} and
SCK2_A pin functions are selected.
Fixes: 6d4036a1e3 ("pinctrl: sh-pfc: Initial R8A77990 PFC support")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.00 of
Aug 24, 2018, the MOD_SEL0 bit3 is set to 0 when TX0_A pin function is
selected, and the MOD_SEL0 bit3 is set to 1 when TX0_B pin function is
selected.
Fixes: 6d4036a1e3 ("pinctrl: sh-pfc: Initial R8A77990 PFC support")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
pinmux_cfg_reg.var_field_width[] is actually a variable-length array,
terminated by a zero, and counting at most r_width entries.
Usually the number of entries is much smaller than r_width, so the
ability to catch bugs at compile time through an "excess elements in
array initializer" warning is fairly limited.
Hence make the array variable-length, decreasing kernel size slightly.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The debug code in sh_pfc_write_config_reg() prints the width of the
field being modified.
However, registers with a variable-width field layout are identified by
pinmux_cfg_reg.field_width being zero, hence zeroes are printed instead
of the actual field widths.
Fix this by printing the Hamming weight of the field mask instead, which
is correct for both fixed-width and variable-width fields.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Some values in the Peripheral Function Select Register 10 descriptor are
shifted by one position, which may cause a peripheral function to be
programmed incorrectly.
Fixing this makes all HSCIF0 pins use Function 4 (value 3), like was
already the case for the HSCK0 pin in field IP10[5:3].
Fixes: ac1ebc2190 ("sh-pfc: Add sh7734 pinmux support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The IP10[5:3] field in Peripheral Function Select Register 10 has a
width of 3 bits, i.e. it allows programming one out of 8 different
configurations.
However, 9 values are provided instead of 8, overflowing into the
subsequent field in the register, and thus breaking the configuration of
the latter.
Fix this by dropping a bogus zero value.
Fixes: ac1ebc2190 ("sh-pfc: Add sh7734 pinmux support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The Port C I/O Register 0 contains 7 reserved bits, but the descriptor
contains only dummy configuration values for 6 reserved bits, thus
breaking the configuration of all subsequent fields in the register.
Fix this by adding the two missing configuration values.
Fixes: f5e811f2a4 ("sh-pfc: Add sh7269 pinmux support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The Port F Control Register 3 (PFCR3) contains only a single field.
However, counting from left to right, it is the fourth field, not the
first field.
Insert the missing dummy configuration values (3 fields of 16 values) to
fix this.
The descriptor for the Port F Control Register 0 (PFCR0) lacks the
description for the 4th field (PF0 Mode, PF0MD[2:0]).
Add the missing configuration values to fix this.
Fixes: a8d42fc421 ("sh-pfc: Add sh7264 pinmux support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
While the SEL_PWM[0-3] fields in the Module Select Register 0 support 4
possible configurations per PWM pin, only the first 3 are valid.
Replace the invalid and unused configurations for SEL_PWM[0-3]_3 by
dummies.
Fixes: 794a671176 ("pinctrl: sh-pfc: Initial R8A77995 PFC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The SEL_I2C1 (MOD_SEL0[21:20]) field in Module Select Register 0 has a
width of 2 bits, i.e. it allows programming one out of 4 different
configurations.
However, the MOD_SEL0_21_20 macro contains 8 values instead of 4,
overflowing into the subsequent fields in the register, and thus breaking
the configuration of the latter.
Fix this by dropping the bogus last 4 values, including the non-existent
SEL_I2C1_4 configuration.
Fixes: 6d4036a1e3 ("pinctrl: sh-pfc: Initial R8A77990 PFC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The Peripheral Function Select Register 11 contains 3 reserved bits and
15 variable-width fields, but the variable field descriptor does not
contain the 3-bit field IP11[25:23].
Fixes: 856cb4bb33 ("sh: Add support pinmux for SH7734")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The Module Select Register 0 contains 20 (= 5 x 4) reserved bits, and 12
single-bit fields, but the variable field descriptor lacks a field of 4
reserved bits.
Fixes: f59125248a ("pinctrl: sh-pfc: Add R8A77980 PFC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The Module Select Register 0 contains 20 (= 5 x 4) reserved bits, and 12
single-bit fields, but the variable field descriptor lacks a field of 4
reserved bits.
Fixes: b92ac66a18 ("pinctrl: sh-pfc: Add R8A77970 PFC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The Peripheral Function Select Register 9 contains 12 fields, but the
variable field descriptor contains a 13th bogus field of 3 bits.
Fixes: 43c4436e2f ("pinctrl: sh-pfc: add R8A7794 PFC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Add a build-time check, to ensure the number of pins and pin marks in a
pin group matches. This helps catching bugs early.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The tpu4_to3_mux[] array contains the TPU4TO3 pin mark, but the
tpu4_to3_pins[] array lacks the corresponding pin number.
Add the missing pin number, for non-GPIO pin F26.
Fixes: 5da4eb049d ("sh-pfc: sh73a0: Add TPU pin groups and functions")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The vin1_b_data18_mux[] arrays contains pin marks for the 2 LSB bits of
the color components. The vin1_b_data18_pins[] array rightfully does
not include the corresponding pin numbers, as RGB18 is subset of RGB24,
containing only the 6 MSB bits of each component.
Fixes: 8e32c9671f ("pinctrl: sh-pfc: r8a7791: Add VIN pins")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The qspi_data4_b_mux[] array contains pin marks for the clock and chip
select pins. The qspi_data4_b_pins[] array rightfully does not contain
the corresponding pin numbers, as the control pins are provided by a
separate group (qspi_ctrl_b).
Fixes: 2d0c386f13 ("pinctrl: sh-pfc: r8a7791: Add QSPI pin groups")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The lcd0_data24_1_pins[] array contains the LCD0 D1[2-5] pin numbers,
but the lcd0_data24_1_mux[] array lacks the corresponding pin marks.
Fixes: 06c7dd866d ("sh-pfc: r8a7740: Add LCDC0 and LCDC1 pin groups and functions")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The gether_gmii_mux[] array contains the REF125CK pin mark, but the
gether_gmii_pins[] array lacks the corresponding pin number.
Fixes: bae11d30d0 ("sh-pfc: r8a7740: Add GETHER pin groups and functions")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Due to an interaction with commit 9f2b76a2db ("pinctrl: sh-pfc:
r8a77990: Add R8A774C0 PFC support"), the state of the I/O Control
Registers is saved/restored during s2ram on RZ/G2E, but not on R-Car E3.
Hence on R-Car E3, SDHI voltage state is lost after system resume.
Fix this by registering the I/O Control Registers on R-Car E3, too.
Fixes: 33847a7137 ("pinctrl: sh-pfc: r8a77990: Add voltage switch operations for SDHI")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The R-Car Gen3 HardWare Manual Errata for Rev. 1.00 (Jul 2, 2018) states
that the USB30_OVC pin supports pull-up only. It has a bit assigned in
the pull-enable register (PUEN5), but not in the pull-up/down control
register (PUD5).
Add a check for this, to prevent configuring a prohibited setting.
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Fixes: 83f6941a42 ("pinctrl: sh-pfc: r8a77990: Add bias pinconf support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Add the QSPI{0|1} pins/groups/functions to the R8A77980 PFC driver.
[Sergei: ported to the upstream driver, fixed up the swapped QSPI0 SPCLK/
SSL pins, fixed up the comments, moved the QSPI pins/groups/functions to
be in the alphanumeric order, removed unneeded empty lines, renamed the
patch.]
Signed-off-by: Dmitry Shifrin <dmitry.shifrin@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds CAN FD{0,1} pins, groups and functions to the R8A77990
SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
[geert: Move canfd from common to automotive]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds CAN{0,1} pins, groups and functions to the R8A77990 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds CAN FD{0,1} pins, groups and functions to the R8A77965
SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds CAN{0,1} pins, groups and functions to the R8A77965 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds I2C{0,3,5} pins, groups and functions to the R8A7796 SoC.
These pins are physically muxed with other pins. Therefore, setup of
MOD_SEL is needed for exclusive control with other pins.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds I2C{0,3,5} pins, groups and functions to
the R8A7795 ES1.x SoC.
These pins are physically muxed with other pins. Therefore, setup of
MOD_SEL is needed for exclusive control with other pins.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds I2C{0,3,5} pins, groups and functions to the R8A7795 SoC.
These pins are physically muxed with other pins. Therefore, setup of
MOD_SEL is needed for exclusive control with other pins.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Used by I2C controllers 0, 3 and 5 in R8A7795 and R8A7796 SoCs.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The PINMUX_IPSR_MSEL2() and PINMUX_IPSR_PHYS() macros are unused, and
will conflict with generic macros that are to be added.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds HSCIF{0,1,2,3,4} pins, groups and functions to
the R8A77990 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add pin, mux and functions definitions for VIN4 and VIN5 for R-Car E3.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The VIN4 and VIN5 interfaces support parallel video input.
Add pin, mux and functions definitions for VIN4 and VIN5 for R-Car M3-N.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Versioned VIN groups can appear on different sets of pins. Using the
VIN_DATA_PIN_GROUP macro now supports proper naming of said groups
through an optional 'version' argument.
Use the 'version' argument for said macro to fix naming of versioned
groups for the R-Car M3-W R8A7796 SoC.
Fixes: a5c2949ff7 ("pinctrl: sh-pfc: r8a7796: Deduplicate VIN4 pin definitions")
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Versioned VIN groups can appear on different sets of pins. Using the
VIN_DATA_PIN_GROUP macro now supports proper naming of said groups
through an optional 'version' argument.
Use the 'version' argument for said macro to fix naming of versioned
groups for the R-Car H3 R8A7795 SoC.
Fixes: 9942a5b529 ("pinctrl: sh-pfc: r8a7795: Deduplicate VIN4 pin definitions")
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Versioned VIN groups can appear on different sets of pins. Using the
VIN_DATA_PIN_GROUP macro now supports proper naming of said groups
through an optional 'version' argument.
Use the 'version' argument for said macro to fix naming of versioned
groups for the R-Car V2H R8A7792 SoC.
Fixes: 7dd74bb1f0 ("pinctrl: sh-pfc: r8a7792: Add VIN pin groups")
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
VIN data groups may appear on different sets of pins, usually named
"vinX_data_[a|b]". The existing VIN_DATA_PIN_GROUP() does not support
appending the '_a' or '_b' suffix, leading to the definition of group
names not consistent with the ones defined using the SH_PFC_PIN_GROUP()
macro.
Fix this by making the VIN_DATA_PIN_GROUP macro a variadic one,
which accepts an optional 'version' argument.
Fixes: 423caa5253 ("pinctrl: sh-pfc: r8a779[01]: Move 'union vin_data' to shared header file")
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the QSPI{0|1} pins/groups/functions to the R8A77970 PFC driver.
[Sergei: ported to the upstream driver, fixed up the swapped QSPI0 SPCLK/
SSL pins, fixed up the comments, moved the QSPI pins/groups/functions to
be in the alphanumeric order, removed unneeded empty lines, renamed the
patch.]
Signed-off-by: Dmitry Shifrin <dmitry.shifrin@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch supports the {get,set}_io_voltage operations of SDHI.
This operates the IOCTRL30 register on the R8A77990 SoC and makes
1.8V/3.3V signal voltage switch possible.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds SDHI{0,1,3} pins, groups and functions to the R8A77990
SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add SH_PFC_PIN_CFG_IO_VOLTAGE definition for the SDHI pins
capable of switching voltage, also add pin groups and functions
for SDHI0 and SDHI1. Please note that with the RZ/G1C only 1
bit of the POC Control Register is used to control each interface.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Some VIN channels support less than 24 lanes. As union vin_data always
consumes space for 24 lanes, this wastes memory.
Hence introduce new smaller unions vin_data12 and vin_data16, to
accommodate VIN channels with only 12 or 16 lanes.
This reduces the static pin controller driver size by 320 bytes for
R-Car V2H, and by 96 bytes for R-Car E2.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
This patch adds Audio SSI{0,1,2,3,4,5,6,7,8,9} pins, groups
and functions to the R8A77990 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[simon: rebase]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds AUDIO_CLK{A,B,C}, AUDIO_CLKOUT, AUDIO_CLKOUT{1,2,3}
pins, groups and functions to the R8A77990 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[simon: rebase]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add QSPI1 pin groups and function to the RZ/G1C (a.k.a. R8A77470)
pinctrl driver.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add VIN[01] pin groups and functions to the RZ/G1C (a.k.a.
R8A77470) pinctrl driver.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add DU1 pin groups and function to the RZ/G1C (a.k.a. R8A77470)
pinctrl driver.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds I2C[0123] groups and functions to the RZ/G1C
(a.k.a. R8A77470) pinctrl driver.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add pins, groups, and function for the Interrupt Controller for
External Devices (INTC-EX) on the R-Car E3 SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Renesas RZ/G SoCs are pin compatible with R-Car SoCs, but lack several
automotive-specific peripherals.
Currently pin groups and functions for automotive-specific peripherals
are grouped in arrays named after the automative SoC part numbers.
Rename them to "automotive" for clarity and consistency.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Add USB[01] pin groups and functions to the R8A77470 SoC.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
