move ath5k_tx_status and ath5k_rx_status structures out of the hardware
descriptor since they are not accessed by the hardware at all. they just
contain converted information from the hardware descriptor. since they are only
used in the rx and tx tasklets there is also no use to keep them for each
descriptor.
drivers/net/wireless/ath5k/ath5k.h: Changes-licensed-under: ISC
drivers/net/wireless/ath5k/base.c: Changes-licensed-under: 3-Clause-BSD
drivers/net/wireless/ath5k/debug.c: Changes-licensed-under: GPL
drivers/net/wireless/ath5k/debug.h: Changes-licensed-under: GPL
drivers/net/wireless/ath5k/hw.c: Changes-licensed-under: ISC
Signed-off-by: Bruno Randolf <bruno@thinktube.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* make struct ath5k_desc clearer by directly including unions of structures,
which correspond to the hardware descriptors of different HW versions (5210
and 5212). before they were casted at onto ath5k_desc at different points
(e.g. ds_hw[2]).
* rename some structures and variable names to make their use clearer, e.g.
struct ath5k_hw_4w_tx_desc to ath5k_hw_4w_tx_ctl.
* substitute "old" with "5210" and "new" with "5212" (eg. rename
ath5k_hw_proc_new_rx_status() to ath5k_hw_proc_5212_rx_status()) because old
and new are relative and we might have a newer structure at some point.
* unify structs ath5k_hw_old_rx_status and ath5k_hw_new_rx_status into one
ath5k_hw_rx_status, because they only differ in the flags and masks.
drivers/net/wireless/ath5k/ath5k.h: Changes-licensed-under: ISC
drivers/net/wireless/ath5k/debug.c: Changes-licensed-under: GPL
drivers/net/wireless/ath5k/hw.c: Changes-licensed-under: ISC
drivers/net/wireless/ath5k/hw.h: Changes-licensed-under: ISC
Signed-off-by: Bruno Randolf <bruno@thinktube.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch grabs NIC access inside iwl4965_tx_queue_agg_disable, instead of the
caller doing it.
The caller must still hold priv->lock when calling the function.
Signed-off-by: Max Stepanov <max.stepanov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch
1. removes cmd completion from iwl3945_tx_queue_reclaim
and creates iwl3945_cmd_queue_reclaim.
1. removes 11n relevant elements from this function
2. removes call to ieee80211_tx_status_irqsafe
and uses ieee80211_tx_status only
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fix 3945 rate scaling after cfg80211 rate/band changes
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves
1. iwl_queue_inc_wrap and int iwl_queue_dec_wrap
into iwl-helpers.h these two functions are identical to common
for both iwl3956 and iwl4965
2. renames x2_queue_used to iwl3945_x2_queue_used
3. exports iwl3945_queue_space out of iwl3964-base.c
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch move EEPROM code into iwl core module
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds iwl-core module to iwlwifi driver.
This module will contain common code and infrastracture for iwlwifi
driver
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes locking unbalance after adding rcu locking
for sta
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cancels an ongoing HW scan upon association. Not doing this
resulted in instability in association.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds fw_name to iwl_cfg. This allows run time selection
of needed fw/ucode file
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch introduces struct iwl_cfg. struct iwl_cfg defines static
configuration for each device type and sku. It is passed as driver_data
to the bus probe function.
This patch also introduce new common header file iwl-core.h
which will represent core functionality of iwlwifi driver
3945ABG uses separate iwl-3945-dev.h header file for now
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
HBUS is accessed through CSR registers
moved to iwl-csr.h
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch extract CSR Register definition into separate
header files as most of the definition are commons to both
3945 and 4965.
Definitions specific for 3945 and 4965 are properly prefixed
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes use of the new mac80211_tx_control_flags and tx_rate to
pass Tx data, regular and 11n, from the HW tx response into the rate scaling.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adapts to 802.11 patch and remove AUTO offset for FAT
channel
Signed-off-by: Guy Cohen <guy.cohen@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds a few debugging counters, that are useful for debugging the
"card does not transmit" or "connection is unstable" kind of problems.
It's also useful for tuning an RC algorithm.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rename the DMA ring pointers to have more descriptive and standard
names. Also remove the 6th unused TX ring. We can add it back later,
if we need it. The unused TX-status rx-ring is also removed, as that's
only used by legacy devices not supported by this driver anyway.
This is no functional change, except less memory allocation for
the removed rings.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds QOS support to the b43 driver.
QOS can be disabled on driver level with a module parameter for debugging purposes.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add 2413 to srev_names so that it shows up during module load.
This is based on the new patch 7 which did not introduce a helper
on ath5k_hw_reset().
Changes-licensed-under: 3-clause-BSD
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@winlab.rutgers.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make some changes which mimic what we see in register dumps.
This patch does not add a helper to ath5k_hw_reset(). It
does seem clear we need a re-shuffle around ath5k_hw_reset()
though as code in there is lengthy and already hitting 80-char
limit. This can be dealt with later though.
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@winlab.rutgers.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Fix nic_wakeup for PCI-E chips (don't set AR5K_RESET_CTL_PCI bit)
* Fix dma size setting for PCI-E chips (thanx to Bob Copeland).
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@winlab.rutgers.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Since RF2413 it seems that RF_BUFFER settings are different (notice
that the last part -"bank 7" or whatever- is smaller than in 5111/5112).
So until we know what's going on we assume there is no gain optimization
stuff in post-5112 chips.
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@winlab.rutgers.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Add AR5K_RF2413 to radio check during hw_reset so it doesn't complain
* Write ah_phy_spending value we set during attach instead of checking
each time for radio revision
* Skip txpower setup for RF2413 because it can't transmit with it
(weird thing is that RF5413 has no problem with it).
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@winlab.rutgers.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Attach RF2413.
* Propertly handle different AR5K_PHY_SPENDING settings for each RF
chip by adding a field in ath5k_hw. This way we won't have to check
inside hw_reset (see next patch).
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@winlab.rutgers.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Add initial settings for RF2413
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@winlab.rutgers.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Add RF2413 srev values and a new entry on ath5k_radio enum for it
since it differs from RF5413 (it's not like 5112-2112).
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@winlab.rutgers.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The previously unused CR_CAM_MODE register is set to MODE_AP_WDS. This makes the
driver ack mesh (WDS) frames. It does not affect Infra functionality of the
driver.
Previously missing beaconing support has been added. This might also help
implement a currently missing ah-hoc mode.
Support for interrupts from the device have been added, but we are not handling
most of them.
Mesh interfaces are considered associated as long as the interface is up.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Should be purely cosmetic apart from the removal of the two pointless
MAC addresses.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The struct enc_key probably wants to die too, but that can come later.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes reporting rate in RX packets in 52 band.
The rate was updated from CCK rate index instead of OFDM rate 6M
Most of the patch is collateral clean up
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch refactors init geos function. It also fixes few minor bugs.
IWL_MAX_RATE -> IWL_RATE_COUNT (IWL_MAX_RATE included also MCS setting)
There are 9 and 13 rates for 4965 in 2.4 and 5.2 respectively (rate 60)
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes unused variable in iwlYYYY_priv
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This helps verify that nothing bad is going on in mac80211,
it is unfortunately not possible to implement this generically
in mac80211 easily because there we can't assume that we only
have a single vif which b43 currently can assume.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes access to the STA hash table/list use RCU to protect
against freeing of items. However, it's not a true RCU, the
copy step is missing: whenever somebody changes a STA item it
is simply updated. This is an existing race condition that is
now somewhat understandable.
This patch also fixes the race key freeing vs. STA destruction
by making sure that sta_info_destroy() is always called under
RTNL and frees the key.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
COSA/SRP driver: The semaphore channel_data.rsem is used as a mutex,
convert it to the mutex API
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the needlessly global init_tti() static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: "Ramkrishna Vepa" <Ramkrishna.Vepa@neterion.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes the following build error introduced by commit
a79d8e93d3 and reported by Olaf Hering:
<-- snip -->
...
LD .tmp_vmlinux1
arch/powerpc/sysdev/built-in.o: In function `of_add_fixed_phys':
fsl_soc.c:(.init.text+0xd34): undefined reference to `fixed_phy_add'
make: *** [.tmp_vmlinux1] Error 1
<-- snip -->
Signed-off-by: Adrian Bunk <adrian.bunk@movial.fi>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes the following build error:
<-- snip -->
...
CC [M] drivers/net/atarilance.o
{standard input}: Assembler messages:
{standard input}:406: Error: symbol `Lberr' is already defined
{standard input}:460: Error: symbol `Lberr' is already defined
make[3]: *** [drivers/net/atarilance.o] Error 1
<-- snip -->
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This fixes a "trying to free already free IRQ" message and simplifies
the shutdown/suspend code by re-using already existing code when going
to suspend. The code is now symmetric with e100_resume.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This message is frequently displayed even if normal file-transfer.
Signed-off-by: Komuro <komurojun-mbn@nifty.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The mv643xx_eth driver can be loaded as a platform device, as is done by
various Orion (ARM) based devices. The driver needs to define a module
alias for the platform driver so udev will load it automatically.
Tested with Debian on a QNAP TS-209.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When the chip dies (probably because of a bug somewhere in the driver),
de_stop_rxtx() fails and changing the media type crashes the whole machine.
Replace BUG_ON() in de_set_media() with a warning.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
