My patch resized the pool size, but neglected to resize
the global table, which is obviously wrong since the global
table maps the pool's rxb to vid one to one. This results
in a panic in 9000 devices.
Add a build bug to avoid such a case in the future.
Fixes: 7b5424361e ("iwlwifi: pcie: fine tune number of rxbs")
Reported-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When trying to reach high Rx throughput of more than 500Mbps on
a device with a relatively weak CPU (Atom x5-Z8500), CPU utilization
may become a bottleneck. Analysis showed that we are looping in
iwl_pcie_rx_handle for very long periods which led to starvation
of other threads (iwl_pcie_rx_handle runs with _bh disabled).
We were handling Rx and allocating new buffers and the new buffers
were ready quickly enough to be available before we had finished
handling all the buffers available in the hardware. As a
consequence, we called iwl_pcie_rxq_restock to refill the hardware
with the new buffers, and start again handling new buffers without
exiting the function. Since we read the hardware pointer again when
we goto restart, new buffers were handled immediately instead of
exiting the function.
This patch avoids refilling RBs inside rx handling loop, unless an
emergency situation is reached. It also doesn't read the hardware
pointer again unless we are in an emergency (unlikely) case.
This significantly reduce the maximal time we spend in
iwl_pcie_rx_handle with _bh disabled.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We kick the allocator when we have 2 RBDs that don't have
attached RBs, and the allocator allocates 8 RBs meaning
that it needs another 6 RBDs to attach the RBs to.
The design is that allocator should always have enough RBDs
to fulfill requests, so we give in advance 6 RBDs to the
allocator so that when it is kicked, it gets additional 2 RBDs
and has enough RBDs.
These RBDs were taken from the Rx queue itself, meaning
that each Rx queue didn't have the maximal number of
RBDs, but MAX - 6.
Change initial number of RBDs in the system to include both
queue size and allocator reserves.
Note the multi-queue is always 511 instead of 512 to avoid a
full queue since we cannot detect this state easily enough in
the 9000 arch.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
128 byte chunk size is supported only on PCIe and not
on IOSF. For now, change it back to 64 byte.
Reported-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Change the code to move rxbs directly from the allocator's
list to the queue's free list. This makes the code more
readable, saves the interim array and the double loop over
the free RBs.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In 9000 series A0 step the closed_rb_num is not wrapping around
properly. The queue is wrapping around as it should, so we can
W/A it by wrapping the closed_rb_num in the driver.
While at it, extend RX logging and add error handling of other
cases HW values may cause us to access invalid memory locations.
Add also a proper masking of vid value read from HW - this should
not have actual affect, but better to be on the safe side.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fine tune RFH registers further:
* Set default queue explicitly
* Set RFH to drop frames exceeding RB size
* Set the maximum rx transfer size to DRAM to 128 instead of 64
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Working with MSIX requires prior configuration.
This includes requesting interrupt vectors from the OS,
registering the vectors and mapping the optional causes to the
relevant interrupt. In addition add new interrupt handler
to handle MSIX interrupt.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
These are a few fixes for the current cycle.
3 out of the 5 patches fix a bugzilla.
* fix a race that users reported when we try to load the firmware
and the hardware rfkill interrupt triggers at the same time.
* Luca fixes a very visible bug in scheduled scan: our firmware
doesn't support scheduled scan with no profile configured and
the supplicant sometimes requests such scheduled scans.
* build system fix
* firmware name update for 8265
* typo fix in return value
When we load the firmware, we hold trans_pcie->mutex to
avoid nested flows. We also rely on the ISR to wake up the
thread when the DMA has finished copying a chunk. During
this flow, we enable the RF-Kill interrupt.
The problem is that the RF-Kill interrupt handler can take
the mutex and bring the device down. This means that if
we load the firmware while the RF-Kill switch is enabled
(which will happen when we load the INIT firmware to read
the device's capabilities and register to mac80211), we
may get an RF-Kill interrupt immediately and the ISR will
be waiting for the mutex held by the thread that is
currently loading the firmware. At this stage, the ISR
won't be able to service the DMA's interrupt needed to
wake up the thread that load the firmware. We are in a
deadlock situation which ends when the thread that loads
the firmware fails on timeout and releases the mutex.
To fix this, take the mutex later in the flow, disable
the interrupts and synchronize_irq() to give a chance to
the RF-Kill interrupt to run and complete.
After that, mask all the interrupts besides the DMA
interrupt and proceed with firmware load. Make sure to
check that there was no RF-Kill interrupt when the
interrupts were disabled.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=111361
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Previous patches enabled new 9000 hardware DMA for one queue
only.
Enable the actual multi-queue path and configuration now.
This requires also per-queue NAPI struct.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The 9000 series introduces several changes in the device
DMA operation.
As the device now supports multi-queue rx, several DMA channels
should be configured.
The flows of providing the device with the allocated RBDs now
changes as well - the device maintains a separate table of used
and free table.
The hardware may use the free table to feed RBDs to any queue.
This requires maintaing a shared table to map returned RBDs to
the original RXB - for that purpose the VID is introduced - an
internal identifier of the RB placed in the lower 12 bits and
returned by HW in the used data.
Another change is the support of 64 bit DMA address.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The 9000 series devices will support multi rx queues.
Current code has one static rx queue - change it to allocate
a number of queues per the device capability (pre-9000 devices
have the number of rx queues set to one).
Subsequent generalizations are:
Change the code to access an explicit numbered rx queue only
when the queue number is known - when handling interrupt, when
accessing the default queue and when iterating the queues.
The rest of the functions will receive the rx queue as a pointer.
Generalize the warning in allocation failure to consider the
allocator status instead of a single rx queue status.
Move the rx initial pool of memory buffers to be shared among
all the queues and allocated to the default queue on init.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Host commands now have a group id, express this in printed messages.
Signed-off-by: Sharon Dvir <sharon.dvir@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
ilw@linux.intel.com is not available anymore.
linuxwifi@intel.com should be used instead.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Since this pointer is not shown anywhere else, it's useless.
Remove it, just keeping the indexes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This message isn't very useful and presents a security risk
due to the use of %p - remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
802.11ac allows A-MSDU that can be up to 12KB long. Since
an entire A-MSDU needs to fit into one single Receive
Buffer (RB), add support for big RBs.
Since this adds lots of pressure to the memory manager and
significantly increase the true_size of the RX buffers,
don't enable this by default.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
