Ensure we correctly report the stateid and status in the layoutreturn on
close tracepoint.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Tegra HDA has audio data buffer for upto tens of frames, this buffer
can help to avoid underflow. HW will keep issuing new data fetch
request when buffers are not full and current BDL is not done. When SW
disable DMA RUN bit for a stream, HW can't cancel the already issued data
fetch request and hence it can't stop DMA. HW has to wait for all issued
data fetch request get data returned before it stops DMA.
This HW behavior is not in sync with HDA spec which says DMA RUN bit
should be cleared within 1 audio frame. For Tegra, DMA RUN bit was
active for more than one audio frame, due to this the timeout in
snd_hdac_stream_sync function is not helping. When Stream reset set
and clear happens during DMA RUN bit active state it results in Memory
Decode error.
Unfortunately, there is no way to detect when these data accesses have
completed, but testing has shown that a 100us delay between Stream reset
set and clear operation for Tegra avoids the memory decode error.
Therefore, adding a 100us dma stop delay.
Signed-off-by: Mohan Kumar <mkumard@nvidia.com>
Link: https://lore.kernel.org/r/20200805095221.5476-4-mkumard@nvidia.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A variable dma_stop_delay is added as a new member in hdac_bus
structure to avoid memory decode error incase DMA RUN bit is not
disabled in the given timeout from snd_hdac_stream_sync function and
followed by stream reset which results in memory decode error between
reset set and clear operation.
Signed-off-by: Mohan Kumar <mkumard@nvidia.com>
Link: https://lore.kernel.org/r/20200805095221.5476-3-mkumard@nvidia.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Set chip->align_buffer_size to 1 for Tegra platforms to make the buffer
alignment to be multiple of 128 bytes. This fix is applied as gstreamer
alsasink gets stuck with the default buffer-time and latency-time
parameters with 4 byte buffer alignment.
Signed-off-by: Mohan Kumar <mkumard@nvidia.com>
Link: https://lore.kernel.org/r/20200805095221.5476-2-mkumard@nvidia.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add SMBus PCI ID on Intel Tiger Lake PCH-H.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add support for SMBus controller on Intel Emmitsburg PCH. This is the
same IP as used in Cannon Lake and derivatives.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
[wsa: shortened commit message]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
And it has been for a while (since 2012 at least), only it was not
documented. Add it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Make the Microchip at91 driver the first to use the generic GPIO bus
recovery support from the I2C core and discard the driver implementation.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Even if I2C bus GPIO recovery is optional, devm_gpiod_get() can return
-EPROBE_DEFER, so we should at least treat that. This ends up with
i2c_register_adapter() to be able to return -EPROBE_DEFER.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Multiple I2C bus drivers use similar bindings to obtain information needed
for I2C recovery. For example, for platforms using device-tree, the
properties look something like this:
&i2c {
...
pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c_default>;
pinctrl-1 = <&pinctrl_i2c_gpio>;
sda-gpios = <&pio 0 GPIO_ACTIVE_HIGH>;
scl-gpios = <&pio 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
...
}
For this reason, we can add this common initialization in the core. This
way, other I2C bus drivers will be able to support GPIO recovery just by
providing a pointer to platform's pinctrl and calling i2c_recover_bus()
when SDA is stuck low.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
[wsa: inverted one logic for better readability, minor update to kdoc]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The I2C GPIO bus recovery properties consist of two GPIOS and one extra
pinctrl state ("gpio" or "recovery"). "recovery" pinctrl state is
considered deprecated and "gpio" should be used instead.
Not all are mandatory for recovery.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Reviewed-by: Rob Herring <robh@kernel.org>
[wsa: kept sorting, minor whitespace change]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
If a TAINT_PROPRIETARY_MODULE exports symbol, inherit the taint flag
for all modules importing these symbols, and don't allow loading
symbols from TAINT_PROPRIETARY_MODULE modules if the module previously
imported gplonly symbols. Add a anti-circumvention devices so people
don't accidentally get themselves into trouble this way.
Comment from Greg:
"Ah, the proven-to-be-illegal "GPL Condom" defense :)"
[jeyu: pr_info -> pr_err and pr_warn as per discussion]
Link: http://lore.kernel.org/r/20200730162957.GA22469@lst.de
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
The sparse tool complains as follows:
drivers/mmc/host/mtk-sd.c:2269:6: warning:
symbol 'msdc_cqe_disable' was not declared. Should it be static?
This function is not used outside of mtk-sd.c, so this commit
marks it static.
Fixes: 88bd652b3c ("mmc: mediatek: command queue support")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Chun-Hung Wu <chun-hung.wu@mediatek.com>
Link: https://lore.kernel.org/r/20200727171129.2945-1-weiyongjun1@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some ioctls via OSS sequencer API may race and lead to UAF when the
port create and delete are performed concurrently, as spotted by a
couple of syzkaller cases. This patch is an attempt to address it by
serializing the ioctls with the existing register_mutex.
Basically OSS sequencer API is an obsoleted interface and was designed
without much consideration of the concurrency. There are very few
applications with it, and the concurrent performance isn't asked,
hence this "big hammer" approach should be good enough.
Reported-by: syzbot+1a54a94bd32716796edd@syzkaller.appspotmail.com
Reported-by: syzbot+9d2abfef257f3e2d4713@syzkaller.appspotmail.com
Suggested-by: Hillf Danton <hdanton@sina.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200804185815.2453-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As Eugen handles the software for bootloaders and new products, handover
the maintenance to him.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Eugen Hristev <eugen.hristev@microchip.com>
Link: https://lore.kernel.org/r/20200709085331.8145-1-ludovic.desroches@microchip.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
while to come. Changes include:
- Some new Chinese translations
- Progress on the battle against double words words and non-HTTPS URLs
- Some block-mq documentation
- More RST conversions from Mauro. At this point, that task is
essentially complete, so we shouldn't see this kind of churn again for a
while. Unless we decide to switch to asciidoc or something...:)
- Lots of typo fixes, warning fixes, and more.
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAl8oVkwPHGNvcmJldEBs
d24ubmV0AAoJEBdDWhNsDH5YoW8H/jJ/xnXFn7tkgVPQAlL3k5HCnK7A5nDP9RVR
cg1pTx1cEFdjzxPlJyExU6/v+AImOvtweHXC+JDK7YcJ6XFUNYXJI3LxL5KwUXbY
BL/xRFszDSXH2C7SJF5GECcFYp01e/FWSLN3yWAh+g+XwsKiTJ8q9+CoIDkHfPGO
7oQsHKFu6s36Af0LfSgxk4sVB7EJbo8e4psuPsP5SUrl+oXRO43Put0rXkR4yJoH
9oOaB51Do5fZp8I4JVAqGXvpXoExyLMO4yw0mASm6YSZ3KyjR8Fae+HD9Cq4ZuwY
0uzb9K+9NEhqbfwtyBsi99S64/6Zo/MonwKwevZuhtsDTK4l4iU=
=JQLZ
-----END PGP SIGNATURE-----
Merge tag 'docs-5.9' of git://git.lwn.net/linux
Pull documentation updates from Jonathan Corbet:
"It's been a busy cycle for documentation - hopefully the busiest for a
while to come. Changes include:
- Some new Chinese translations
- Progress on the battle against double words words and non-HTTPS
URLs
- Some block-mq documentation
- More RST conversions from Mauro. At this point, that task is
essentially complete, so we shouldn't see this kind of churn again
for a while. Unless we decide to switch to asciidoc or
something...:)
- Lots of typo fixes, warning fixes, and more"
* tag 'docs-5.9' of git://git.lwn.net/linux: (195 commits)
scripts/kernel-doc: optionally treat warnings as errors
docs: ia64: correct typo
mailmap: add entry for <alobakin@marvell.com>
doc/zh_CN: add cpu-load Chinese version
Documentation/admin-guide: tainted-kernels: fix spelling mistake
MAINTAINERS: adjust kprobes.rst entry to new location
devices.txt: document rfkill allocation
PCI: correct flag name
docs: filesystems: vfs: correct flag name
docs: filesystems: vfs: correct sync_mode flag names
docs: path-lookup: markup fixes for emphasis
docs: path-lookup: more markup fixes
docs: path-lookup: fix HTML entity mojibake
CREDITS: Replace HTTP links with HTTPS ones
docs: process: Add an example for creating a fixes tag
doc/zh_CN: add Chinese translation prefer section
doc/zh_CN: add clearing-warn-once Chinese version
doc/zh_CN: add admin-guide index
doc:it_IT: process: coding-style.rst: Correct __maybe_unused compiler label
futex: MAINTAINERS: Re-add selftests directory
...
-----BEGIN PGP SIGNATURE-----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=ZcMq
-----END PGP SIGNATURE-----
Merge tag 'printk-for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux
Pull printk updates from Petr Mladek:
- Herbert Xu made printk header file self-contained.
- Andy Shevchenko and Sergey Senozhatsky cleaned up console->setup()
error handling.
- Andy Shevchenko did some cleanups (e.g. sparse warning) in vsprintf
code.
- Minor documentation updates.
* tag 'printk-for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux:
lib/vsprintf: Force type of flags value for gfp_t
lib/vsprintf: Replace custom spec to print decimals with generic one
lib/vsprintf: Replace hidden BUILD_BUG_ON() with static_assert()
printk: Make linux/printk.h self-contained
doc:kmsg: explicitly state the return value in case of SEEK_CUR
Replace HTTP links with HTTPS ones: vsprintf
hvc: unify console setup naming
console: Fix trivia typo 'change' -> 'chance'
console: Propagate error code from console ->setup()
tty: hvc: Return proper error code from console ->setup() hook
serial: sunzilog: Return proper error code from console ->setup() hook
serial: sunsab: Return proper error code from console ->setup() hook
mips: Return proper error code from console ->setup() hook
Pull parisc updates from Helge Deller:
"The majority of the patches are reverts of previous commits regarding
the parisc-specific low level spinlocking code and barrier handling,
with which we tried to fix CPU stalls on our build servers. In the end
John David Anglin found the culprit: We missed a define for
atomic64_set_release(). This seems to have fixed our issues, so now
it's good to remove the unnecessary code again.
Other than that it's trivial stuff: Spelling fixes, constifications
and such"
* 'parisc-5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: make the log level string for register dumps const
parisc: Do not use an ordered store in pa_tlb_lock()
Revert "parisc: Revert "Release spinlocks using ordered store""
Revert "parisc: Use ldcw instruction for SMP spinlock release barrier"
Revert "parisc: Drop LDCW barrier in CAS code when running UP"
Revert "parisc: Improve interrupt handling in arch_spin_lock_flags()"
parisc: Replace HTTP links with HTTPS ones
parisc: elf.h: delete a duplicated word
parisc: Report bad pages as HardwareCorrupted
parisc: Convert to BIT_MASK() and BIT_WORD()
this has been brought into a shape which is maintainable and actually
works.
This final version was done by Sasha Levin who took it up after Intel
dropped the ball. Sasha discovered that the SGX (sic!) offerings out there
ship rogue kernel modules enabling FSGSBASE behind the kernels back which
opens an instantanious unpriviledged root hole.
The FSGSBASE instructions provide a considerable speedup of the context
switch path and enable user space to write GSBASE without kernel
interaction. This enablement requires careful handling of the exception
entries which go through the paranoid entry path as they cannot longer rely
on the assumption that user GSBASE is positive (as enforced via prctl() on
non FSGSBASE enabled systemn). All other entries (syscalls, interrupts and
exceptions) can still just utilize SWAPGS unconditionally when the entry
comes from user space. Converting these entries to use FSGSBASE has no
benefit as SWAPGS is only marginally slower than WRGSBASE and locating and
retrieving the kernel GSBASE value is not a free operation either. The real
benefit of RD/WRGSBASE is the avoidance of the MSR reads and writes.
The changes come with appropriate selftests and have held up in field
testing against the (sanitized) Graphene-SGX driver.
-----BEGIN PGP SIGNATURE-----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=QaAN
-----END PGP SIGNATURE-----
Merge tag 'x86-fsgsbase-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fsgsbase from Thomas Gleixner:
"Support for FSGSBASE. Almost 5 years after the first RFC to support
it, this has been brought into a shape which is maintainable and
actually works.
This final version was done by Sasha Levin who took it up after Intel
dropped the ball. Sasha discovered that the SGX (sic!) offerings out
there ship rogue kernel modules enabling FSGSBASE behind the kernels
back which opens an instantanious unpriviledged root hole.
The FSGSBASE instructions provide a considerable speedup of the
context switch path and enable user space to write GSBASE without
kernel interaction. This enablement requires careful handling of the
exception entries which go through the paranoid entry path as they
can no longer rely on the assumption that user GSBASE is positive (as
enforced via prctl() on non FSGSBASE enabled systemn).
All other entries (syscalls, interrupts and exceptions) can still just
utilize SWAPGS unconditionally when the entry comes from user space.
Converting these entries to use FSGSBASE has no benefit as SWAPGS is
only marginally slower than WRGSBASE and locating and retrieving the
kernel GSBASE value is not a free operation either. The real benefit
of RD/WRGSBASE is the avoidance of the MSR reads and writes.
The changes come with appropriate selftests and have held up in field
testing against the (sanitized) Graphene-SGX driver"
* tag 'x86-fsgsbase-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (21 commits)
x86/fsgsbase: Fix Xen PV support
x86/ptrace: Fix 32-bit PTRACE_SETREGS vs fsbase and gsbase
selftests/x86/fsgsbase: Add a missing memory constraint
selftests/x86/fsgsbase: Fix a comment in the ptrace_write_gsbase test
selftests/x86: Add a syscall_arg_fault_64 test for negative GSBASE
selftests/x86/fsgsbase: Test ptracer-induced GS base write with FSGSBASE
selftests/x86/fsgsbase: Test GS selector on ptracer-induced GS base write
Documentation/x86/64: Add documentation for GS/FS addressing mode
x86/elf: Enumerate kernel FSGSBASE capability in AT_HWCAP2
x86/cpu: Enable FSGSBASE on 64bit by default and add a chicken bit
x86/entry/64: Handle FSGSBASE enabled paranoid entry/exit
x86/entry/64: Introduce the FIND_PERCPU_BASE macro
x86/entry/64: Switch CR3 before SWAPGS in paranoid entry
x86/speculation/swapgs: Check FSGSBASE in enabling SWAPGS mitigation
x86/process/64: Use FSGSBASE instructions on thread copy and ptrace
x86/process/64: Use FSBSBASE in switch_to() if available
x86/process/64: Make save_fsgs_for_kvm() ready for FSGSBASE
x86/fsgsbase/64: Enable FSGSBASE instructions in helper functions
x86/fsgsbase/64: Add intrinsics for FSGSBASE instructions
x86/cpu: Add 'unsafe_fsgsbase' to enable CR4.FSGSBASE
...
to the generic code. Pretty much a straight forward 1:1 conversion plus the
consolidation of the KVM handling of pending work before entering guest
mode.
-----BEGIN PGP SIGNATURE-----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=84y7
-----END PGP SIGNATURE-----
Merge tag 'x86-entry-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 conversion to generic entry code from Thomas Gleixner:
"The conversion of X86 syscall, interrupt and exception entry/exit
handling to the generic code.
Pretty much a straight-forward 1:1 conversion plus the consolidation
of the KVM handling of pending work before entering guest mode"
* tag 'x86-entry-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/kvm: Use __xfer_to_guest_mode_work_pending() in kvm_run_vcpu()
x86/kvm: Use generic xfer to guest work function
x86/entry: Cleanup idtentry_enter/exit
x86/entry: Use generic interrupt entry/exit code
x86/entry: Cleanup idtentry_entry/exit_user
x86/entry: Use generic syscall exit functionality
x86/entry: Use generic syscall entry function
x86/ptrace: Provide pt_regs helper for entry/exit
x86/entry: Move user return notifier out of loop
x86/entry: Consolidate 32/64 bit syscall entry
x86/entry: Consolidate check_user_regs()
x86: Correct noinstr qualifiers
x86/idtentry: Remove stale comment
entry/exit functionality based on the recent X86 effort to ensure
correctness of entry/exit vs. RCU and instrumentation.
As this functionality and the required entry/exit sequences are not
architecture specific, sharing them allows other architectures to benefit
instead of copying the same code over and over again.
This branch was kept standalone to allow others to work on it. The
conversion of x86 comes in a seperate pull request which obviously is based
on this branch.
-----BEGIN PGP SIGNATURE-----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=y2Ew
-----END PGP SIGNATURE-----
Merge tag 'core-entry-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull generic kernel entry/exit code from Thomas Gleixner:
"Generic implementation of common syscall, interrupt and exception
entry/exit functionality based on the recent X86 effort to ensure
correctness of entry/exit vs RCU and instrumentation.
As this functionality and the required entry/exit sequences are not
architecture specific, sharing them allows other architectures to
benefit instead of copying the same code over and over again.
This branch was kept standalone to allow others to work on it. The
conversion of x86 comes in a seperate pull request which obviously is
based on this branch"
* tag 'core-entry-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
entry: Correct __secure_computing() stub
entry: Correct 'noinstr' attributes
entry: Provide infrastructure for work before transitioning to guest mode
entry: Provide generic interrupt entry/exit code
entry: Provide generic syscall exit function
entry: Provide generic syscall entry functionality
seccomp: Provide stub for __secure_computing()
Current behaviour: every time a v3 operation is re-sent to the server
we update (double) the timeout. There is no distinction between whether
or not the previous timer had expired before the re-sent happened.
Here's the scenario:
1. Client sends a v3 operation
2. Server RST-s the connection (prior to the timeout) (eg., connection
is immediately reset)
3. Client re-sends a v3 operation but the timeout is now 120sec.
As a result, an application sees 2mins pause before a retry in case
server again does not reply.
Instead, this patch proposes to keep track off when the minor timeout
should happen and if it didn't, then don't update the new timeout.
Value is updated based on the previous value to make timeouts
predictable.
Signed-off-by: Olga Kornievskaia <kolga@netapp.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Add the character device during rproc_add. This would create
a character device node at /dev/remoteproc<index>. Userspace
applications can interact with the remote processor using this
interface.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Signed-off-by: Siddharth Gupta <sidgup@codeaurora.org>
Link: https://lore.kernel.org/r/1596044401-22083-3-git-send-email-sidgup@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add the character device interface into remoteproc framework.
This interface can be used in order to boot/shutdown remote
subsystems and provides a basic ioctl based interface to implement
supplementary functionality. An ioctl call is implemented to enable
the shutdown on release feature which will allow remote processors to
be shutdown when the controlling userspace application crashes or hangs.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Signed-off-by: Siddharth Gupta <sidgup@codeaurora.org>
Link: https://lore.kernel.org/r/1596044401-22083-2-git-send-email-sidgup@codeaurora.org
[bjorn: s/int32_t/s32/ per checkpatch]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The NFS_CONTEXT_ERROR_WRITE flag (as well as the check of said flag) was
removed by commit 6fbda89b25. The absence of an error check allows
writes to be continually queued up for a server that may no longer be
able to handle them. Fix it by adding an error check using the generic
error reporting functions.
Fixes: 6fbda89b25 ("NFS: Replace custom error reporting mechanism with generic one")
Signed-off-by: Scott Mayhew <smayhew@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
- Prevent unnecessary timer softirq invocations by extending the tracking
of the next expiring timer in the timer wheel beyond the existing NOHZ
functionality. The tracking overhead at enqueue time is within the
noise, but on sensitive workloads the avoidance of the soft interrupt
invocation is a measurable improvement.
- The obligatory new clocksource driver for Ingenic X100 OST
- The usual fixes, improvements, cleanups and extensions for newer chip
variants all over the driver space.
-----BEGIN PGP SIGNATURE-----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=uJnp
-----END PGP SIGNATURE-----
Merge tag 'timers-core-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer updates from Thomas Gleixner:
"Time, timers and related driver updates:
- Prevent unnecessary timer softirq invocations by extending the
tracking of the next expiring timer in the timer wheel beyond the
existing NOHZ functionality.
The tracking overhead at enqueue time is within the noise, but on
sensitive workloads the avoidance of the soft interrupt invocation
is a measurable improvement.
- The obligatory new clocksource driver for Ingenic X100 OST
- The usual fixes, improvements, cleanups and extensions for newer
chip variants all over the driver space"
* tag 'timers-core-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (28 commits)
timers: Recalculate next timer interrupt only when necessary
clocksource/drivers/ingenic: Add support for the Ingenic X1000 OST.
dt-bindings: timer: Add Ingenic X1000 OST bindings.
clocksource/drivers: Replace HTTP links with HTTPS ones
clocksource/drivers/nomadik-mtu: Handle 32kHz clock
clocksource/drivers/sh_cmt: Use "kHz" for kilohertz
clocksource/drivers/imx: Add support for i.MX TPM driver with ARM64
clocksource/drivers/ingenic: Add high resolution timer support for SMP/SMT.
timers: Lower base clock forwarding threshold
timers: Remove must_forward_clk
timers: Spare timer softirq until next expiry
timers: Expand clk forward logic beyond nohz
timers: Reuse next expiry cache after nohz exit
timers: Always keep track of next expiry
timers: Optimize _next_timer_interrupt() level iteration
timers: Add comments about calc_index() ceiling work
timers: Move trigger_dyntick_cpu() to enqueue_timer()
timers: Use only bucket expiry for base->next_expiry value
timers: Preserve higher bits of expiration on index calculation
clocksource/drivers/timer-atmel-tcb: Add sama5d2 support
...
- Infrastructure to allow building irqchip drivers as modules
- Consolidation of irqchip ACPI probing
- Removal of the EOI-preflow interrupt handler which was required for
SPARC support and became obsolete after SPARC was converted to
use sparse interrupts.
- Cleanups, fixes and improvements all over the place
-----BEGIN PGP SIGNATURE-----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=KA8b
-----END PGP SIGNATURE-----
Merge tag 'irq-core-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"The usual boring updates from the interrupt subsystem:
- Infrastructure to allow building irqchip drivers as modules
- Consolidation of irqchip ACPI probing
- Removal of the EOI-preflow interrupt handler which was required for
SPARC support and became obsolete after SPARC was converted to use
sparse interrupts.
- Cleanups, fixes and improvements all over the place"
* tag 'irq-core-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (51 commits)
irqchip/loongson-pch-pic: Fix the misused irq flow handler
irqchip/loongson-htvec: Support 8 groups of HT vectors
irqchip/loongson-liointc: Fix misuse of gc->mask_cache
dt-bindings: interrupt-controller: Update Loongson HTVEC description
irqchip/imx-intmux: Fix irqdata regs save in imx_intmux_runtime_suspend()
irqchip/imx-intmux: Implement intmux runtime power management
irqchip/gic-v4.1: Use GFP_ATOMIC flag in allocate_vpe_l1_table()
irqchip: Fix IRQCHIP_PLATFORM_DRIVER_* compilation by including module.h
irqchip/stm32-exti: Map direct event to irq parent
irqchip/mtk-cirq: Convert to a platform driver
irqchip/mtk-sysirq: Convert to a platform driver
irqchip/qcom-pdc: Switch to using IRQCHIP_PLATFORM_DRIVER helper macros
irqchip: Add IRQCHIP_PLATFORM_DRIVER_BEGIN/END and IRQCHIP_MATCH helper macros
irqchip: irq-bcm2836.h: drop a duplicated word
irqchip/gic-v4.1: Ensure accessing the correct RD when writing INVALLR
irqchip/irq-bcm7038-l1: Guard uses of cpu_logical_map
irqchip/gic-v3: Remove unused register definition
irqchip/qcom-pdc: Allow QCOM_PDC to be loadable as a permanent module
genirq: Export irq_chip_retrigger_hierarchy and irq_chip_set_vcpu_affinity_parent
irqdomain: Export irq_domain_update_bus_token
...
Add a simple helper to grab a reference to a file and install it at
the next available fd, and switch the early init code over to it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Update lpfc version to 12.8.0.3
Link: https://lore.kernel.org/r/20200803210229.23063-9-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On devices that support FCP sequence error recovery, which attempts to
preserve the devices login across link bounce, adisc is used for device
validation. Turns out the device fc4 type is cleared as part of the link
bounce, but the ADISC handling doesn't restore the FC4 support as it
normally would with a PRLI. This caused situations where the device wasn't
reregistered with the transport thus scan logic and LUN discovery never
kicked in.
In the ADISC completion handling, reset the fc4 type so that transport port
reregistration occurs with the remote port.
Link: https://lore.kernel.org/r/20200803210229.23063-8-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are a couple of code areas which validate sufficient reply buffer
length, but the checks are using the request elements rather than the reply
elements.
Rework to validate using the reply structures.
Link: https://lore.kernel.org/r/20200803210229.23063-7-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
With port bounce/address swaps and timing between initiator GID queries vs
remote port FC4 support registrations, the driver may be in a situation
where it sends PRLIs for both FCP and NVME even though the target may not
support one of the protocols. In this case, the remote port will reject the
PRLI and usually indicate it does not support the request. However, the
driver currently ignores the status of the failure and immediately retries
the PRLI, which is pointless. In the case of this one remote port, the
reception of the PRLI retry caused it to decide to send a LOGO. The LOGO
restarted the process and the same results happened. It made the remote
port undiscoverable to either protocol.
Add logic to detect the non-support status and not attempt the retry
of the PRLI.
Link: https://lore.kernel.org/r/20200803210229.23063-6-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While mds diagnostic tests are running, if the driver is requested to be
unloaded, oops or hangs are observed. The driver doesn't terminate the
processing of diag frames when the unload is started. As such: oops may be
seen for __lpfc_sli_release_iocbq_s4 because ring memory is referenced that
was already freed; or hangs see in lpfc_nvme_wait_for_io_drain as ios no
longer complete.
If unloading, don't process diag frames. Just clean them up.
Link: https://lore.kernel.org/r/20200803210229.23063-5-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In configs with a large number of initiators in the same zone (>250), RSCN
timeouts are seen when creating or deleting vports:
lpfc 0000:07:00.1: 5:(0):0231 RSCN timeout Data: x0 x3
During RSCN processing driver issues GID_FT command to nameserver. A
counter for number of simultaneous GID_FT commands is maintained (an
unsigned value). The counter is incremented when the GID_FT is issued. If
the GID_FT command fails for some reason the driver retries the GID_FT from
the completion call back. But the counter was decremented before the retry
was issued. When the second GID_FT completes, the callback again tries to
decrement the counter, possibly wrapping to a very large non-zero value,
which causes the RSCN cleanup code to not execute. Thus the RSCN timeout
failure.
Do not decrement the counter on a retry. Also add defensive checks to
ensure the counter is not decremented if already zero.
Link: https://lore.kernel.org/r/20200803210229.23063-4-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If module parameters override the default configuration settings for
hardware queues or irqs, the driver was not notifying the change from
defaults.
Revise such that any changes will result in a kernel log message.
Link: https://lore.kernel.org/r/20200803210229.23063-3-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Current Link speed was shown as "unknown" in sysfs for FCoE ports. In this
scenario, the port was working in 20G speed, which happens to not be a
speed handled by the driver.
Add support for all possible link speeds that could get reported from
port_speed field in link state ACQE.
Additionally, as supported_speeds can't be manipulated via the FCoE driver
on a converged ethernet port (it must be managed by the nic function),
don't fill out the supported_speeds field for the fc host object in sysfs.
Revise debug logging to report Link speed mgmt valuess.
Link: https://lore.kernel.org/r/20200803210229.23063-2-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
lpfc_init() misses a call misc_deregister() in an error path. Add a label
'unregister' to fix it.
Link: https://lore.kernel.org/r/20200731065639.190646-1-jingxiangfeng@huawei.com
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Jing Xiangfeng <jingxiangfeng@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We cannot wait on a completion object in the lpfc_nvme_targetport structure
in the _destroy_targetport() code path because the NVMe/fc transport will
free that structure immediately after the .targetport_delete() callback.
This results in a use-after-free, and a crash if slub_debug=FZPU is
enabled.
An earlier fix put put the completion on the stack, but commit 2a0fb340fc
("scsi: lpfc: Correct localport timeout duration error") subsequently
changed the code to reference the completion through a pointer in the
object rather than the local stack variable. Fix this by using the stack
variable directly.
Link: https://lore.kernel.org/r/20200729231011.13240-1-emilne@redhat.com
Fixes: 2a0fb340fc ("scsi: lpfc: Correct localport timeout duration error")
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, for zoned disks, since blk_revalidate_disk_zones() requires the
disk capacity to be set already to operate correctly, zones revalidation
can only be done on the second revalidate scan once the gendisk capacity is
set at the end of the first scan. As a result, if zone revalidation fails,
there is no second chance to recover from the failure and the disk capacity
is changed to 0, with the disk left unusable.
This can be improved by shuffling around code, specifically, by moving the
call to sd_zbc_revalidate_zones() from sd_zbc_read_zones() to the end of
sd_revalidate_disk(), after set_capacity_revalidate_and_notify() is called
to set the gendisk capacity. With this change, if sd_zbc_revalidate_zones()
fails on the first scan, the second scan will call it again to recover, if
possible.
Using the new struct scsi_disk fields rev_nr_zones and rev_zone_blocks,
sd_zbc_revalidate_zones() does actual work only if it detects a change with
the disk zone configuration. This means that for a successful zones
revalidation on the first scan, the second scan will not cause another
heavy full check.
While at it, remove the unecesary "extern" declaration of
sd_zbc_read_zones().
Link: https://lore.kernel.org/r/20200731054928.668547-1-damien.lemoal@wdc.com
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In fc_disc_gpn_id_resp(), skb is supposed to get freed in all cases except
for PTR_ERR. However, in some cases it didn't.
This fix is to call fc_frame_free(fp) before function returns.
Link: https://lore.kernel.org/r/20200729081824.30996-2-jhasan@marvell.com
Reviewed-by: Girish Basrur <gbasrur@marvell.com>
Reviewed-by: Santosh Vernekar <svernekar@marvell.com>
Reviewed-by: Saurav Kashyap <skashyap@marvell.com>
Reviewed-by: Shyam Sundar <ssundar@marvell.com>
Signed-off-by: Javed Hasan <jhasan@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In fcoe_sysfs_fcf_del(), we first deleted the fcf from the list and then
freed it if ctlr_dev was not NULL. This was causing a memory leak.
Free the fcf even if ctlr_dev is NULL.
Link: https://lore.kernel.org/r/20200729081824.30996-3-jhasan@marvell.com
Reviewed-by: Girish Basrur <gbasrur@marvell.com>
Reviewed-by: Santosh Vernekar <svernekar@marvell.com>
Reviewed-by: Saurav Kashyap <skashyap@marvell.com>
Reviewed-by: Shyam Sundar <ssundar@marvell.com>
Signed-off-by: Javed Hasan <jhasan@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This function always returns 0. We can make it return void to simplify the
code. Also, no caller ever checks the return value of this function.
Link: https://lore.kernel.org/r/20200803150008.83920-1-maxg@mellanox.com
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- make support for dma_ops optional
- move more code out of line
- add generic support for a dma_ops bypass mode
- misc cleanups
-----BEGIN PGP SIGNATURE-----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=90UK
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-5.9' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- make support for dma_ops optional
- move more code out of line
- add generic support for a dma_ops bypass mode
- misc cleanups
* tag 'dma-mapping-5.9' of git://git.infradead.org/users/hch/dma-mapping:
dma-contiguous: cleanup dma_alloc_contiguous
dma-debug: use named initializers for dir2name
powerpc: use the generic dma_ops_bypass mode
dma-mapping: add a dma_ops_bypass flag to struct device
dma-mapping: make support for dma ops optional
dma-mapping: inline the fast path dma-direct calls
dma-mapping: move the remaining DMA API calls out of line
On exit, if a process is preempted after the trace_sched_process_exit()
tracepoint but before the process is done exiting, then when it gets
scheduled in, the function tracers will not filter it properly against the
function tracing pid filters.
That is because the function tracing pid filters hooks to the
sched_process_exit() tracepoint to remove the exiting task's pid from the
filter list. Because the filtering happens at the sched_switch tracepoint,
when the exiting task schedules back in to finish up the exit, it will no
longer be in the function pid filtering tables.
This was noticeable in the notrace self tests on a preemptable kernel, as
the tests would fail as it exits and preempted after being taken off the
notrace filter table and on scheduling back in it would not be in the
notrace list, and then the ending of the exit function would trace. The test
detected this and would fail.
Cc: stable@vger.kernel.org
Cc: Namhyung Kim <namhyung@kernel.org>
Fixes: 1e10486ffe ("ftrace: Add 'function-fork' trace option")
Fixes: c37775d578 ("tracing: Add infrastructure to allow set_event_pid to follow children"
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
On distros using older glibc versions, the pkey tests encounter build
failures due to redefinition of the pkey syscall numbers.
For compatibility, commit 743f3544ff added a wrapper for the
gettid() syscall and included syscall.h if the version of glibc used
is older than 2.30. This leads to different definitions of SYS_pkey_*
as the ones in the pkey test header set numeric constants where as the
ones from syscall.h reuse __NR_pkey_*. The compiler complains about
redefinitions since they are different.
This replaces SYS_pkey_* definitions with __NR_pkey_* such that the
definitions in both syscall.h and pkeys.h are alike. This way, if
syscall.h has to be included for compatibility reasons, builds will
still succeed.
Fixes: 743f3544ff ("selftests/powerpc: Add wrapper for gettid")
Reported-by: Sachin Sant <sachinp@linux.vnet.ibm.com>
Suggested-by: David Laight <david.laight@aculab.com>
Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sandipan Das <sandipan@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/a4956d838bf59b0a71a2553c5ca81131ea8b49b9.1596561758.git.sandipan@linux.ibm.com
