Loongson 3 used the IORESOURCE_ROM_COPY flag for its ROM resource. There
are two problems with this:
- When IORESOURCE_ROM_COPY is set, pci_map_rom() assumes the resource
contains virtual addresses, so it doesn't ioremap the resource. This
implies loongson_sysconf.vgabios_addr is a virtual address. That's a
problem because resources should contain CPU *physical* addresses not
virtual addresses.
- When IORESOURCE_ROM_COPY is set, pci_cleanup_rom() calls kfree() on the
resource. We did not kmalloc() the loongson_sysconf.vgabios_addr area,
so it is incorrect to kfree() it.
If we're using a shadow copy in RAM for the Loongson 3 VGA BIOS area,
disable the ROM BAR and release the address space it was consuming.
Use IORESOURCE_ROM_SHADOW instead of IORESOURCE_ROM_COPY. This means the
struct resource contains CPU physical addresses, and pci_map_rom() will
ioremap() it as needed.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use a temporary struct resource pointer to avoid needless repetition of
"pdev->resource[PCI_ROM_RESOURCE]". No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
In case of error, the function devm_ioremap_resource() returns
ERR_PTR() and never returns NULL. The NULL test in the return
value check should be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: John Crispin <blogic@openwrt.org>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12451/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The "a" version of the MT7620 has single port PCIE bus. The driver is
straightforward without any special magic required. The driver works on
MT7620 and MT7628. There are a few magic values that get written to the
pcie phy and a register of which we only know the name. I marked these
places as vodoo in the comments above the code.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11996/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
c861519fcf ("MIPS: Fix delay loops which may
be removed by GCC.") which made it upstream was an outdated version of the
patch and is lacking some the removal of two variables that became unused
thus resulting in further warnings and build breakage. The commit
from ae878615d7cee5d7346946cf1ae1b60e427013c2 was correct however.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
GCC 4.1 and newer remove empty loops. This becomes a problem when delay
loops get removed. Fixed by rewriting to user the proper Linux interface
for such delays.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Reported-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: John Crispin <blogic@openwrt.org>
for_each_child_of_node performs an of_node_get on each iteration, so no
of_node_get is needed on breaking out of the loop when the device_node
structure is saved in another variable.
A simplified semantic match that finds this problem is as follows
(http://coccinelle.lip6.fr):
// <smpl>
@@
expression root;
local idexpression child;
@@
for_each_child_of_node(root, child) {
...
* of_node_get(child)
...
break;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: kernel-janitors@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Patchwork: https://patchwork.linux-mips.org/patch/11357/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Resource management
- Revert pci_read_bridge_bases() unification (Bjorn Helgaas)
- Clear IORESOURCE_UNSET when clipping a bridge window (Bjorn Helgaas)
MSI
- Fix MSI IRQ domains for VFs on virtual buses (Alex Williamson)
Renesas R-Car host bridge driver
- Add R8A7794 support (Sergei Shtylyov)
Miscellaneous
- Fix devfn for VPD access through function 0 (Alex Williamson)
- Use function 0 VPD only for identical functions (Alex Williamson)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=f4c3
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.3-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"These are fixes for things we merged for v4.3 (VPD, MSI, and bridge
window management), and a new Renesas R8A7794 SoC device ID.
Details:
Resource management:
- Revert pci_read_bridge_bases() unification (Bjorn Helgaas)
- Clear IORESOURCE_UNSET when clipping a bridge window (Bjorn
Helgaas)
MSI:
- Fix MSI IRQ domains for VFs on virtual buses (Alex Williamson)
Renesas R-Car host bridge driver:
- Add R8A7794 support (Sergei Shtylyov)
Miscellaneous:
- Fix devfn for VPD access through function 0 (Alex Williamson)
- Use function 0 VPD only for identical functions (Alex Williamson)"
* tag 'pci-v4.3-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: rcar: Add R8A7794 support
PCI: Use function 0 VPD for identical functions, regular VPD for others
PCI: Fix devfn for VPD access through function 0
PCI/MSI: Fix MSI IRQ domains for VFs on virtual buses
PCI: Clear IORESOURCE_UNSET when clipping a bridge window
PCI: Revert "PCI: Call pci_read_bridge_bases() from core instead of arch code"
Most interrupt flow handlers do not use the irq argument. Those few
which use it can retrieve the irq number from the irq descriptor.
Remove the argument.
Search and replace was done with coccinelle and some extra helper
scripts around it. Thanks to Julia for her help!
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Revert dff22d2054 ("PCI: Call pci_read_bridge_bases() from core instead
of arch code").
Reading PCI bridge windows is not arch-specific in itself, but there is PCI
core code that doesn't work correctly if we read them too early. For
example, Hannes found this case on an ARM Freescale i.mx6 board:
pci_bus 0000:00: root bus resource [mem 0x01000000-0x01efffff]
pci 0000:00:00.0: PCI bridge to [bus 01-ff]
pci 0000:00:00.0: BAR 8: no space for [mem size 0x01000000] (mem window)
pci 0000:01:00.0: BAR 2: failed to assign [mem size 0x00200000]
pci 0000:01:00.0: BAR 1: failed to assign [mem size 0x00004000]
pci 0000:01:00.0: BAR 0: failed to assign [mem size 0x00000100]
The 00:00.0 mem window needs to be at least 3MB: the 01:00.0 device needs
0x204100 of space, and mem windows are megabyte-aligned.
Bus sizing can increase a bridge window size, but never *decrease* it (see
d65245c329 ("PCI: don't shrink bridge resources")). Prior to
dff22d2054, ARM didn't read bridge windows at all, so the "original size"
was zero, and we assigned a 3MB window.
After dff22d2054, we read the bridge windows before sizing the bus. The
firmware programmed a 16MB window (size 0x01000000) in 00:00.0, and since
we never decrease the size, we kept 16MB even though we only needed 3MB.
But 16MB doesn't fit in the host bridge aperture, so we failed to assign
space for the window and the downstream devices.
I think this is a defect in the PCI core: we shouldn't rely on the firmware
to assign sensible windows.
Ray reported a similar problem, also on ARM, with Broadcom iProc.
Issues like this are too hard to fix right now, so revert dff22d2054.
Reported-by: Hannes <oe5hpm@gmail.com>
Reported-by: Ray Jui <rjui@broadcom.com>
Link: http://lkml.kernel.org/r/CAAa04yFQEUJm7Jj1qMT57-LG7ZGtnhNDBe=PpSRa70Mj+XhW-A@mail.gmail.com
Link: http://lkml.kernel.org/r/55F75BB8.4070405@broadcom.com
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for 4.3 for MIPS. Here's the summary:
Three fixes that didn't make 4.2-stable:
- a -Os build might compile the kernel using the MIPS16 instruction
set but the R2 optimized inline functions in <uapi/asm/swab.h> are
implemented using 32-bit wide instructions which is invalid.
- a build error in pgtable-bits.h for a particular kernel
configuration.
- accessing registers of the CM GCR might have been compiled to use
64 bit accesses but these registers are onl 32 bit wide.
And also a few new bits:
- move the ATH79 GPIO driver to drivers/gpio
- the definition of IRQCHIP_DECLARE has moved to linux/irqchip.h,
change ATH79 accordingly.
- fix definition of pgprot_writecombine
- add an implementation of dma_map_ops.mmap
- fix alignment of quiet build output for vmlinuz link
- BCM47xx: Use kmemdup rather than duplicating its implementation
- Netlogic: Fix 0x0x prefixes of constants.
- merge Bjorn Helgaas' series to remove most of the weak keywords
from function declarations.
- CP0 and CP1 registers are best considered treated as unsigned
values to avoid large values from becoming negative values.
- improve support for the MIPS GIC timer.
- enable common clock framework for Malta and SEAD3.
- a number of improvments and fixes to dump_tlb().
- document the MIPS TLB dump functionality in Magic SysRq.
- Cavium Octeon CN68XX improvments.
- NetLogic improvments.
- irq: Use access helper irq_data_get_affinity_mask.
- handle MSA unaligned accesses.
- a number of R6-related math-emu fixes.
- support for I6400.
- improvments to MSA support.
- add uprobes support.
- move from deprecated __initcall to arch_initcall.
- remove finish_arch_switch().
- IRQ cleanups by Thomas Gleixner.
- migrate to new 'set-state' interface.
- random small cleanups"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (148 commits)
MIPS: UAPI: Fix unrecognized opcode WSBH/DSBH/DSHD when using MIPS16.
MIPS: Fix alignment of quiet build output for vmlinuz link
MIPS: math-emu: Remove unused handle_dsemul function declaration
MIPS: math-emu: Add support for the MIPS R6 MAX{, A} FPU instruction
MIPS: math-emu: Add support for the MIPS R6 MIN{, A} FPU instruction
MIPS: math-emu: Add support for the MIPS R6 CLASS FPU instruction
MIPS: math-emu: Add support for the MIPS R6 RINT FPU instruction
MIPS: math-emu: Add support for the MIPS R6 MSUBF FPU instruction
MIPS: math-emu: Add support for the MIPS R6 MADDF FPU instruction
MIPS: math-emu: Add support for the MIPS R6 SELNEZ FPU instruction
MIPS: math-emu: Add support for the MIPS R6 SELEQZ FPU instruction
MIPS: math-emu: Add support for the CMP.condn.fmt R6 instruction
MIPS: inst.h: Add new MIPS R6 FPU opcodes
MIPS: Octeon: Fix management port MII address on Kontron S1901
MIPS: BCM47xx: Use kmemdup rather than duplicating its implementation
STAGING: Octeon: Use common helpers for determining interface and port
MIPS: Octeon: Support interfaces 4 and 5
MIPS: Octeon: Set up 1:1 mapping between CN68XX PKO queues and ports
MIPS: Octeon: Initialize CN68XX PKO
STAGING: Octeon: Support CN68XX style WQE
...
Update mips/netlogic/common/irq.c and mips/pci/msi-xlp.c to use chip_data
to store interrupt controller data pointer. It uses handler_data now,
and that causes errors when an API (like the GPIO subsystem) tries to
use the handler data.
Signed-off-by: Kamlakant Patel <kamlakant.patel@broadcom.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10817/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Currently CONFIG_ARCH_HAVE_CUSTOM_GPIO_H is defined for all MIPS
machines, and each machine type provides its own gpio.h. However
only a handful really implement the GPIO API, most just forward
everythings to gpiolib.
The Alchemy machine is notable as it provides a system to allow
implementing the GPIO API at the board level. But it is not used by
any board currently supported, so it can also be removed.
For most machine types we can just remove the custom gpio.h, as well
as the custom wrappers if some exists. Some of the code found in
the wrappers must be moved to the respective GPIO driver.
A few more fixes are need in some drivers as they rely on linux/gpio.h
to provides some machine specific definitions, or used asm/gpio.h
instead of linux/gpio.h for the gpio API.
Signed-off-by: Alban Bedel <albeu@free.fr>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Joe Perches <joe@perches.com>
Cc: Daniel Walter <dwalter@google.com>
Cc: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: James Hartley <james.hartley@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Varka Bhadram <varkabhadram@gmail.com>
Cc: Masanari Iida <standby24x7@gmail.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Michael Buesch <m@bues.ch>
Cc: abdoulaye berthe <berthe.ab@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-ide@vger.kernel.org
Cc: linux-gpio@vger.kernel.org
Cc: linux-input@vger.kernel.org
Cc: netdev@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10828/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull irq updates from Thomas Gleixner:
"This updated pull request does not contain the last few GIC related
patches which were reported to cause a regression. There is a fix
available, but I let it breed for a couple of days first.
The irq departement provides:
- new infrastructure to support non PCI based MSI interrupts
- a couple of new irq chip drivers
- the usual pile of fixlets and updates to irq chip drivers
- preparatory changes for removal of the irq argument from interrupt
flow handlers
- preparatory changes to remove IRQF_VALID"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (129 commits)
irqchip/imx-gpcv2: IMX GPCv2 driver for wakeup sources
irqchip: Add bcm2836 interrupt controller for Raspberry Pi 2
irqchip: Add documentation for the bcm2836 interrupt controller
irqchip/bcm2835: Add support for being used as a second level controller
irqchip/bcm2835: Refactor handle_IRQ() calls out of MAKE_HWIRQ
PCI: xilinx: Fix typo in function name
irqchip/gic: Ensure gic_cpu_if_up/down() programs correct GIC instance
irqchip/gic: Only allow the primary GIC to set the CPU map
PCI/MSI: pci-xgene-msi: Consolidate chained IRQ handler install/remove
unicore32/irq: Prepare puv3_gpio_handler for irq argument removal
tile/pci_gx: Prepare trio_handle_level_irq for irq argument removal
m68k/irq: Prepare irq handlers for irq argument removal
C6X/megamode-pic: Prepare megamod_irq_cascade for irq argument removal
blackfin: Prepare irq handlers for irq argument removal
arc/irq: Prepare idu_cascade_isr for irq argument removal
sparc/irq: Use access helper irq_data_get_affinity_mask()
sparc/irq: Use helper irq_data_get_irq_handler_data()
parisc/irq: Use access helper irq_data_get_affinity_mask()
mn10300/irq: Use access helper irq_data_get_affinity_mask()
irqchip/i8259: Prepare i8259_irq_dispatch for irq argument removal
...
The db_assert call checks whether the bus_num pointer is non-NULL, but
does so after said pointer has been dereferenced by the assignment on
the previous line. Thus the check is pointless & likely to have been
optimised out by the compiler anyway. The check_args function is static
& only ever called from the local file with bus_num being a pointer to
an on-stack variable, so the check seems somewhat overzealous anyway.
Simply remove it.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10692/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The irq argument of most interrupt flow handlers is unused or merily
used instead of a local variable. The handlers which need the irq
argument can retrieve the irq number from the irq descriptor.
Search and update was done with coccinelle and the invaluable help of
Julia Lawall.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: linux-mips@linux-mips.org
Cc: LKML <linux-kernel@vger.kernel.org>
Patchwork: https://patchwork.linux-mips.org/patch/10706/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Chained irq handlers usually set up handler data as well. We now have
a function to set both under irq_desc->lock. Replace the two calls
with one.
Search and conversion was done with coccinelle.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: LKML <linux-kernel@vger.kernel.org>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Patchwork: https://patchwork.linux-mips.org/patch/10698/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Chained irq handlers usually set up handler data as well. We now have
a function to set both under irq_desc->lock. Replace the two calls
with one.
Search and conversion was done with coccinelle.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: linux-mips@linux-mips.org
Cc: LKML <linux-kernel@vger.kernel.org>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Patchwork: https://patchwork.linux-mips.org/patch/10697/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Chained irq handlers usually set up handler data as well. We now have
a function to set both under irq_desc->lock. Replace the two calls
with one.
Search and conversion was done with coccinelle.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: linux-mips@linux-mips.org
Cc: LKML <linux-kernel@vger.kernel.org>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Patchwork: https://patchwork.linux-mips.org/patch/10696/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When we scan a PCI bus, we read PCI-PCI bridge window registers with
pci_read_bridge_bases() so we can validate the resource hierarchy. Most
architectures call pci_read_bridge_bases() from pcibios_fixup_bus(), but
PCI-PCI bridges are not arch-specific, so this doesn't need to be in
arch-specific code.
Call pci_read_bridge_bases() directly from the PCI core instead of from
arch code.
For alpha and mips, we now call pci_read_bridge_bases() always; previously
we only called it if PCI_PROBE_ONLY was set.
[bhelgaas: changelog]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Ralf Baechle <ralf@linux-mips.org>
CC: James E.J. Bottomley <jejb@parisc-linux.org>
CC: Michael Ellerman <mpe@ellerman.id.au>
CC: Bjorn Helgaas <bhelgaas@google.com>
CC: Richard Henderson <rth@twiddle.net>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: David Howells <dhowells@redhat.com>
CC: Russell King <linux@arm.linux.org.uk>
CC: Tony Luck <tony.luck@intel.com>
CC: David S. Miller <davem@davemloft.net>
CC: Ingo Molnar <mingo@redhat.com>
CC: Guenter Roeck <linux@roeck-us.net>
CC: Michal Simek <monstr@monstr.eu>
CC: Chris Zankel <chris@zankel.net>
Use accessor for_each_pci_msi_entry() to access MSI device list, so we
could easily move msi_list from struct pci_dev into struct device
later.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mips@linux-mips.org
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Stuart Yoder <stuart.yoder@freescale.com>
Cc: Yijing Wang <wangyijing@huawei.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Link: http://lkml.kernel.org/r/1436428847-8886-3-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull irq fixes from Thomas Gleixner:
"This contains:
- a series of fixes for interrupt drivers to prevent a potential race
when installing a chained interrupt handler
- a fix for cpumask pointer misuse
- a fix for using the wrong interrupt number from struct irq_data
- removal of unused code and outdated comments
- a few new helper functions which allow us to cleanup the interrupt
handling code further in 4.3
I decided against doing the cleanup at the end of this merge window
and rather do the preparatory steps for 4.3, so we can run the final
ABI change at the end of the 4.3 merge window with less risk"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (26 commits)
ARM/LPC32xx: Use irq not hwirq for __irq_set_handler_locked()
genirq: Implement irq_set_handler_locked()/irq_set_chip_handler_name_locked()
genirq: Introduce helper irq_desc_get_irq()
genirq: Remove irq_node()
genirq: Clean up outdated comments related to include/linux/irqdesc.h
mn10300: Fix incorrect use of irq_data->affinity
MIPS/ralink: Fix race in installing chained IRQ handler
MIPS/pci: Fix race in installing chained IRQ handler
MIPS/ath25: Fix race in installing chained IRQ handler
MIPS/ath25: Fix race in installing chained IRQ handler
m68k/psc: Fix race in installing chained IRQ handler
avr32/at32ap: Fix race in installing chained IRQ handler
sh/intc: Fix race in installing chained IRQ handler
sh/intc: Fix potential race in installing chained IRQ handler
pinctrl/sun4i: Fix race in installing chained IRQ handler
pinctrl/samsung: Fix race in installing chained IRQ handler
pinctrl/samsung: Fix race in installing chained IRQ handler
pinctrl/exynos: Fix race in installing chained IRQ handler
pinctrl/st: Fix race in installing chained IRQ handler
pinctrl/adi2: Fix race in installing chained IRQ handler
...
Pull MIPS updates from Ralf Baechle:
- Improvements to the tlb_dump code
- KVM fixes
- Add support for appended DTB
- Minor improvements to the R12000 support
- Minor improvements to the R12000 support
- Various platform improvments for BCM47xx
- The usual pile of minor cleanups
- A number of BPF fixes and improvments
- Some improvments to the support for R3000 and DECstations
- Some improvments to the ATH79 platform support
- A major patchset for the JZ4740 SOC adding support for the CI20 platform
- Add support for the Pistachio SOC
- Minor BMIPS/BCM63xx platform support improvments.
- Avoid "SYNC 0" as memory barrier when unlocking spinlocks
- Add support for the XWR-1750 board.
- Paul's __cpuinit/__cpuinitdata cleanups.
- New Malta CPU board support large memory so enable ZONE_DMA32.
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (131 commits)
MIPS: spinlock: Adjust arch_spin_lock back-off time
MIPS: asmmacro: Ensure 64-bit FP registers are used with MSA
MIPS: BCM47xx: Simplify handling SPROM revisions
MIPS: Cobalt Don't use module_init in non-modular MTD registration.
MIPS: BCM47xx: Move NVRAM driver to the drivers/firmware/
MIPS: use for_each_sg()
MIPS: BCM47xx: Don't select BCMA_HOST_PCI
MIPS: BCM47xx: Add helper variable for storing NVRAM length
MIPS: IRQ/IP27: Move IRQ allocation API to platform code.
MIPS: Replace smp_mb with release barrier function in unlocks.
MIPS: i8259: DT support
MIPS: Malta: Basic DT plumbing
MIPS: include errno.h for ENODEV in mips-cm.h
MIPS: Define GCR_GIC_STATUS register fields
MIPS: BPF: Introduce BPF ASM helpers
MIPS: BPF: Use BPF register names to describe the ABI
MIPS: BPF: Move register definition to the BPF header
MIPS: net: BPF: Replace RSIZE with SZREG
MIPS: BPF: Free up some callee-saved registers
MIPS: Xtalk: Update xwidget.h with known Xtalk device numbers
...
Fix a race where a pending interrupt could be received and the handler
called before the handler's data has been setup, by converting to
irq_set_chained_handler_and_data().
Search and conversion was done with coccinelle:
@@
expression E1, E2, E3;
@@
(
-if (irq_set_chained_handler(E1, E3) != 0)
- BUG();
|
-irq_set_chained_handler(E1, E3);
)
-irq_set_handler_data(E1, E2);
+irq_set_chained_handler_and_data(E1, E3, E2);
@@
expression E1, E2, E3;
@@
(
-if (irq_set_chained_handler(E1, E3) != 0)
- BUG();
...
|
-irq_set_chained_handler(E1, E3);
...
)
-irq_set_handler_data(E1, E2);
+irq_set_chained_handler_and_data(E1, E3, E2);
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Cc: linux-mips@linux-mips.org
The DDR controller need to be used by the IRQ controller to flush
the write buffer of some devices before running the IRQ handler.
It is also used by the PCI controller to setup the PCI memory windows.
The current interface used to access the DDR controller doesn't
provides any useful abstraction and simply rely on a shared global
pointer.
Replace this by a simple API to setup the PCI memory windows and use
the write buffer flush independently of the SoC type. That remove the
need for the shared global pointer, simplify the IRQ handler code.
[ralf@linux-mips.org: Folded in Alban Bedel's follup fix.]
Signed-off-by: Alban Bedel <albeu@free.fr>
Cc: linux-mips@linux-mips.org
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9773/
Patchwork: http://patchwork.linux-mips.org/patch/10543/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use irq_desc_get_xxx() to avoid redundant lookup of irq_desc while we
already have a pointer to corresponding irq_desc.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Acked-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Aleksey Makarov <aleksey.makarov@auriga.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: x86@kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Cc: linux-acpi@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10086/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In include/linux/pci.h, we already #include <asm/pci.h>, so we don't need
to include <asm/pci.h> directly.
Remove the unnecessary includes. All the files here already include
<linux/pci.h>.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au> # sh
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS for Linux 4.1. Most
noteworthy:
- Add more Octeon-optimized crypto functions
- Octeon crypto preemption and locking fixes
- Little endian support for Octeon
- Use correct CSR to soft reset Octeons
- Support LEDs on the Octeon-based DSR-1000N
- Fix PCI interrupt mapping for the Octeon-based DSR-1000N
- Mark prom_free_prom_memory() as __init for a number of systems
- Support for Imagination's Pistachio SOC. This includes arch and
CLK bits. I'd like to merge pinctrl bits later
- Improve parallelism of csum_partial for certain pipelines
- Organize DTB files in subdirs like other architectures
- Implement read_sched_clock for all MIPS platforms other than
Octeon
- Massive series of 38 fixes and cleanups for the FPU emulator /
kernel
- Further FPU remulator work to support new features. This sits on a
separate branch which also has been pulled into the 4.1 KVM branch
- Clean up and fixes for the SEAD3 eval board; remove unused file
- Various updates for Netlogic platforms
- A number of small updates for Loongson 3 platforms
- Increase the memory limit for ATH79 platforms to 256MB
- A fair number of fixes and updates for BCM47xx platforms
- Finish the implementation of XPA support
- MIPS FDC support. No, not floppy controller but Fast Debug Channel :)
- Detect the R16000 used in SGI legacy platforms
- Fix Kconfig dependencies for the SSB bus support"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (265 commits)
MIPS: Makefile: Fix MIPS ASE detection code
MIPS: asm: elf: Set O32 default FPU flags
MIPS: BCM47XX: Fix detecting Microsoft MN-700 & Asus WL500G
MIPS: Kconfig: Disable SMP/CPS for 64-bit
MIPS: Hibernate: flush TLB entries earlier
MIPS: smp-cps: cpu_set FPU mask if FPU present
MIPS: lose_fpu(): Disable FPU when MSA enabled
MIPS: ralink: add missing symbol for RALINK_ILL_ACC
MIPS: ralink: Fix bad config symbol in PCI makefile.
SSB: fix Kconfig dependencies
MIPS: Malta: Detect and fix bad memsize values
Revert "MIPS: Avoid pipeline stalls on some MIPS32R2 cores."
MIPS: Octeon: Delete override of cpu_has_mips_r2_exec_hazard.
MIPS: Fix cpu_has_mips_r2_exec_hazard.
MIPS: kernel: entry.S: Set correct ISA level for mips_ihb
MIPS: asm: spinlock: Fix addiu instruction for R10000_LLSC_WAR case
MIPS: r4kcache: Use correct base register for MIPS R6 cache flushes
MIPS: Kconfig: Fix typo for the r2-to-r6 emulator kernel parameter
MIPS: unaligned: Fix regular load/store instruction emulation for EVA
MIPS: unaligned: Surround load/store macros in do {} while statements
...
A wrong symbol is referenced by commit 187c26ddf0 ("MIPS: ralink: add rt2880
pci driver"). Fix this by changing it to the correct symbol.
Signed-off-by: John Crispin <blogic@openwrt.org>
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9298/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix PCI interrupt mapping for DSR1000N. This will get the PCI slot
interrupts working. The mapping is based on D-Link GPL tarball.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9593/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
udelay() in PCI/PCIe read/write callbacks cause 30ms IRQ latency on Octeon
platforms because these operations are called from PCI_OP_READ() and
PCI_OP_WRITE() under raw_spin_lock_irqsave().
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Cc: linux-mips@linux-mips.org
Cc: David Daney <ddaney@cavium.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Masanari Iida <standby24x7@gmail.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Mathias <mathias.rulf@nokia.com>
Patchwork: https://patchwork.linux-mips.org/patch/9576/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On SGI Origin 2k/Onyx2 and SGI Octane systems, there can exist multiple PCI
buses attached to the Xtalk bus. The current code will stop counting PCI buses
after it finds the first one. If one installs the optional PCI cardcage
("shoebox") into these systems, because of the order of the Xtalk widgets, the
current PCI code will find the cardcage first, and fail to detect the BaseIO
PCI devices, which are on a higher Xtalk widget ID.
This patch adds the hooks needed for resolving this issue in the IP27 PCI code
(in a later patch).
Verified on both an SGI Onyx2 and an SGI Octane.
Signed-off-by: Joshua Kinard <kumba@gentoo.org>
Cc: Linux MIPS List <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/9074/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The per-cpu interrupt ACK using EIRR has to be done just once after
all the bits in the status register are processed.
PIC ack has to be done once in case of MSI, and for every interrupt
in case of MSI-X
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8887/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Return errors immediately so the straightline path is the normal,
no-error path. No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously, pci_scan_root_bus() created a root PCI bus, enumerated the
devices on it, and called pci_bus_add_devices(), which made the devices
available for drivers to claim them.
Most callers assigned resources to devices after pci_scan_root_bus()
returns, which may be after drivers have claimed the devices. This is
incorrect; the PCI core should not change device resources while a driver
is managing the device.
Remove pci_bus_add_devices() from pci_scan_root_bus() and do it after any
resource assignment in the callers.
Note that ARM's pci_common_init_dev() already called pci_bus_add_devices()
after pci_scan_root_bus(), so we only need to remove the first call:
pci_common_init_dev
pcibios_init_hw
pci_scan_root_bus
pci_bus_add_devices # first call
pci_bus_assign_resources
pci_bus_add_devices # second call
[bhelgaas: changelog, drop "root_bus" var in alpha common_init_pci(),
return failure earlier in mn10300, add "return" in x86 pcibios_scan_root(),
return early if xtensa platform_pcibios_fixup() fails]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Richard Henderson <rth@twiddle.net>
CC: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
CC: Matt Turner <mattst88@gmail.com>
CC: David Howells <dhowells@redhat.com>
CC: Tony Luck <tony.luck@intel.com>
CC: Michal Simek <monstr@monstr.eu>
CC: Ralf Baechle <ralf@linux-mips.org>
CC: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
CC: Sebastian Ott <sebott@linux.vnet.ibm.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Chris Metcalf <cmetcalf@ezchip.com>
CC: Chris Zankel <chris@zankel.net>
CC: Max Filippov <jcmvbkbc@gmail.com>
CC: Thomas Gleixner <tglx@linutronix.de>
Some instances of pci_ops initialization rely on the read/write members'
location in the struct. This is fragile and may break when adding new
members to the beginning of the struct.
[ralf@linux-mips.org: indent = with tabs for consistency.]
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-pci@vger.kernel.org
Cc: Bjorn Helgaas <bhelgaas@google.com>
Patchwork: https://patchwork.linux-mips.org/patch/8915/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
Pull MIPS updates from Ralf Baechle:
"This is an unusually large pull request for MIPS - in parts because
lots of patches missed the 3.18 deadline but primarily because some
folks opened the flood gates.
- Retire the MIPS-specific phys_t with the generic phys_addr_t.
- Improvments for the backtrace code used by oprofile.
- Better backtraces on SMP systems.
- Cleanups for the Octeon platform code.
- Cleanups and fixes for the Loongson platform code.
- Cleanups and fixes to the firmware library.
- Switch ATH79 platform to use the firmware library.
- Grand overhault to the SEAD3 and Malta interrupt code.
- Move the GIC interrupt code to drivers/irqchip
- Lots of GIC cleanups and updates to the GIC code to use modern IRQ
infrastructures and features of the kernel.
- OF documentation updates for the GIC bindings
- Move GIC clocksource driver to drivers/clocksource
- Merge GIC clocksource driver with clockevent driver.
- Further updates to bring the GIC clocksource driver up to date.
- R3000 TLB code cleanups
- Improvments to the Loongson 3 platform code.
- Convert pr_warning to pr_warn.
- Merge a bunch of small lantiq and ralink fixes that have been
staged/lingering inside the openwrt tree for a while.
- Update archhelp for IP22/IP32
- Fix a number of issues for Loongson 1B.
- New clocksource and clockevent driver for Loongson 1B.
- Further work on clk handling for Loongson 1B.
- Platform work for Broadcom BMIPS.
- Error handling cleanups for TurboChannel.
- Fixes and optimization to the microMIPS support.
- Option to disable the FTLB.
- Dump more relevant information on machine check exception
- Change binfmt to allow arch to examine PT_*PROC headers
- Support for new style FPU register model in O32
- VDSO randomization.
- BCM47xx cleanups
- BCM47xx reimplement the way the kernel accesses NVRAM information.
- Random cleanups
- Add support for ATH25 platforms
- Remove pointless locking code in some PCI platforms.
- Some improvments to EVA support
- Minor Alchemy cleanup"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (185 commits)
MIPS: Add MFHC0 and MTHC0 instructions to uasm.
MIPS: Cosmetic cleanups of page table headers.
MIPS: Add CP0 macros for extended EntryLo registers
MIPS: Remove now unused definition of phys_t.
MIPS: Replace use of phys_t with phys_addr_t.
MIPS: Replace MIPS-specific 64BIT_PHYS_ADDR with generic PHYS_ADDR_T_64BIT
PCMCIA: Alchemy Don't select 64BIT_PHYS_ADDR in Kconfig.
MIPS: lib: memset: Clean up some MIPS{EL,EB} ifdefery
MIPS: iomap: Use __mem_{read,write}{b,w,l} for MMIO
MIPS: <asm/types.h> fix indentation.
MAINTAINERS: Add entry for BMIPS multiplatform kernel
MIPS: Enable VDSO randomization
MIPS: Remove a temporary hack for debugging cache flushes in SMTC configuration
MIPS: Remove declaration of obsolete arch_init_clk_ops()
MIPS: atomic.h: Reformat to fit in 79 columns
MIPS: Apply `.insn' to fixup labels throughout
MIPS: Fix microMIPS LL/SC immediate offsets
MIPS: Kconfig: Only allow 32-bit microMIPS builds
MIPS: signal.c: Fix an invalid cast in ISA mode bit handling
MIPS: mm: Only build one microassembler that is suitable
...
Pull irq domain updates from Thomas Gleixner:
"The real interesting irq updates:
- Support for hierarchical irq domains:
For complex interrupt routing scenarios where more than one
interrupt related chip is involved we had no proper representation
in the generic interrupt infrastructure so far. That made people
implement rather ugly constructs in their nested irq chip
implementations. The main offenders are x86 and arm/gic.
To distangle that mess we have now hierarchical irqdomains which
seperate the various interrupt chips and connect them via the
hierarchical domains. That keeps the domain specific details
internal to the particular hierarchy level and removes the
criss/cross referencing of chip internals. The resulting hierarchy
for a complex x86 system will look like this:
vector mapped: 74
msi-0 mapped: 2
dmar-ir-1 mapped: 69
ioapic-1 mapped: 4
ioapic-0 mapped: 20
pci-msi-2 mapped: 45
dmar-ir-0 mapped: 3
ioapic-2 mapped: 1
pci-msi-1 mapped: 2
htirq mapped: 0
Neither ioapic nor pci-msi know about the dmar interrupt remapping
between themself and the vector domain. If interrupt remapping is
disabled ioapic and pci-msi become direct childs of the vector
domain.
In hindsight we should have done that years ago, but in hindsight
we always know better :)
- Support for generic MSI interrupt domain handling
We have more and more non PCI related MSI interrupts, so providing
a generic infrastructure for this is better than having all
affected architectures implementing their own private hacks.
- Support for PCI-MSI interrupt domain handling, based on the generic
MSI support.
This part carries the pci/msi branch from Bjorn Helgaas pci tree to
avoid a massive conflict. The PCI/MSI parts are acked by Bjorn.
I have two more branches on top of this. The full conversion of x86
to hierarchical domains and a partial conversion of arm/gic"
* 'irq-irqdomain-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (41 commits)
genirq: Move irq_chip_write_msi_msg() helper to core
PCI/MSI: Allow an msi_controller to be associated to an irq domain
PCI/MSI: Provide mechanism to alloc/free MSI/MSIX interrupt from irqdomain
PCI/MSI: Enhance core to support hierarchy irqdomain
PCI/MSI: Move cached entry functions to irq core
genirq: Provide default callbacks for msi_domain_ops
genirq: Introduce msi_domain_alloc/free_irqs()
asm-generic: Add msi.h
genirq: Add generic msi irq domain support
genirq: Introduce callback irq_chip.irq_write_msi_msg
genirq: Work around __irq_set_handler vs stacked domains ordering issues
irqdomain: Introduce helper function irq_domain_add_hierarchy()
irqdomain: Implement a method to automatically call parent domains alloc/free
genirq: Introduce helper irq_domain_set_info() to reduce duplicated code
genirq: Split out flow handler typedefs into seperate header file
genirq: Add IRQ_SET_MASK_OK_DONE to support stacked irqchip
genirq: Introduce irq_chip.irq_compose_msi_msg() to support stacked irqchip
genirq: Add more helper functions to support stacked irq_chip
genirq: Introduce helper functions to support stacked irq_chip
irqdomain: Do irq_find_mapping and set_type for hierarchy irqdomain in case OF
...
Use the much more common pr_warn instead of pr_warning
with the goal of removing pr_warning eventually.
Other miscellanea:
o Coalesce formats
o Realign arguments
Signed-off-by: Joe Perches <joe@perches.com>
Cc: linux-mips <linux-mips@linux-mips.org>
Cc: LKML <linux-kernel@vger.kernel.org>
Patchwork: https://patchwork.linux-mips.org/patch/7935/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Caller (generic PCI code) already do proper locking so no need to add
another one here. Local PCI read/write functions are never called
simultaneously, also they do not require synchronization with the PCI
controller ops, since they are used before the controller registration.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Cc: Linux MIPS <linux-mips@linux-mips.org>
Cc: Gabor Juhos <juhosg@openwrt.org>
Patchwork: https://patchwork.linux-mips.org/patch/7603/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Caller (generic PCI code) already do proper locking so no need to add
another one here.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Cc: Linux MIPS <linux-mips@linux-mips.org>
Cc: Gabor Juhos <juhosg@openwrt.org>
Patchwork: https://patchwork.linux-mips.org/patch/7602/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Caller (generic PCI code) already do proper locking so no need to add
another one here.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Cc: Linux MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7601/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Caller (generic PCI code) already do proper locking so no need to add
another one here.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Cc: Linux MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7600/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
