Add hwmod support to enable access to UART4 of the AM35xx series of
chips. The UART4 device referenced from the TRM will show up as ttyO3.
This was tested on an AM3505.
Signed-off-by: Kyle Manna <kyle.manna@fuel7.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Seems the commit 7e89098 was overly aggressive in adding iva and mailbox
hwmods so now they are registered twice.
------------[ cut here ]------------
WARNING: at arch/arm/mach-omap2/omap_hwmod.c:1959 omap_hwmod_register+0x104/0x12c()
omap_hwmod: iva: _register returned -22
Modules linked in:
[<c0012aa4>] (unwind_backtrace+0x0/0xec) from [<c002f970>] (warn_slowpath_common+0x4c/0x64)
[<c002f970>] (warn_slowpath_common+0x4c/0x64) from [<c002fa08>] (warn_slowpath_fmt+0x2c/0x3c)
[<c002fa08>] (warn_slowpath_fmt+0x2c/0x3c) from [<c02fdb4c>] (omap_hwmod_register+0x104/0x12c)
[<c02fdb4c>] (omap_hwmod_register+0x104/0x12c) from [<c02fbb44>] (omap3_init_early+0x1c/0x28)
[<c02fbb44>] (omap3_init_early+0x1c/0x28) from [<c02f9580>] (setup_arch+0x6b8/0x7a4)
[<c02f9580>] (setup_arch+0x6b8/0x7a4) from [<c02f754c>] (start_kernel+0x6c/0x264)
[<c02f754c>] (start_kernel+0x6c/0x264) from [<80008040>] (0x80008040)
---[ end trace 1b75b31a2719ed1c ]---
------------[ cut here ]------------
WARNING: at arch/arm/mach-omap2/omap_hwmod.c:1959 omap_hwmod_register+0x104/0x12c()
omap_hwmod: mailbox: _register returned -22
Modules linked in:
[<c0012aa4>] (unwind_backtrace+0x0/0xec) from [<c002f970>] (warn_slowpath_common+0x4c/0x64)
[<c002f970>] (warn_slowpath_common+0x4c/0x64) from [<c002fa08>] (warn_slowpath_fmt+0x2c/0x3c)
[<c002fa08>] (warn_slowpath_fmt+0x2c/0x3c) from [<c02fdb4c>] (omap_hwmod_register+0x104/0x12c)
[<c02fdb4c>] (omap_hwmod_register+0x104/0x12c) from [<c02fbb44>] (omap3_init_early+0x1c/0x28)
[<c02fbb44>] (omap3_init_early+0x1c/0x28) from [<c02f9580>] (setup_arch+0x6b8/0x7a4)
[<c02f9580>] (setup_arch+0x6b8/0x7a4) from [<c02f754c>] (start_kernel+0x6c/0x264)
[<c02f754c>] (start_kernel+0x6c/0x264) from [<80008040>] (0x80008040)
---[ end trace 1b75b31a2719ed1d ]---
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Omap_uart_can_sleep function blocks system wide low power state until
uart is active remove this func and add qos requests to prevent
MPU from transitioning.
Keep qos request to default value which will allow MPU to transition
and while uart baud rate is available calculate the latency value
from the baudrate and use the same to hold constraint while uart clocks
are enabled, and if uart is auto-idled the constraint is updated with
default constraint value allowing MPU to transition.
Qos requests are blocking notifier calls so put these requests to
work queue, also the driver uses irq_safe version of runtime API's
and callbacks can be called in interrupt disabled context.
So to avoid warn on slow path warning while using qos update
API's from runtime callbacks use the qos_work_queue.
During bootup the runtime_resume call backs might not be called and runtime
callback gets called only after uart is idled by setting the autosuspend
timeout. So qos_request from runtime resume callback might not activated during
boot if uart baudrate is calculated during bootup for console uart, so schedule
the qos_work queue once we calc_latency while configuring the uart port.
Flush and complete any pending qos jobs in work queue while suspending.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: Kevin Hilman <khilman@ti.com>
If OMAP UART is used as console uart and debug is enabled,
avoid gating of uart clocks to print all debug prints.
If uart clocks are gated then the debug prints from omap_device
framework or hwmod framework can cause uart to enter recursive
pm_runtime calls, which can cause a deadlock over power lock usage.
For example: Say, uart clocks are cut and we get a print from
omap_device_disable stating disabling uart clocks. This print
calls omap_uart driver console_write which will call runtime API
get_sync which means we enter from runtime API put context to
runtime API get context.
--> runtime put (take power lock)
--> print disabling uart clocks
--> call uart console write
--> call get_sync (try to take power lock)
Also any clock enable API call from uart driver should not call any uart
operation until clocks are enabled back. Like get_sync having debug print
calling uart console write even before clocks are enabled.
So to avoid these scenarios, identify from bootargs if OMAP_UART(ttyO) is used
in debug mode. If so, do not set device_may_wakeup. This will prevent
pm_runtime_enable in uart driver and will avoid uart clock gating.
Debug is enabled either by adding debug word in bootarg or by setting
loglevel=10
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
If no_console_suspend is used we have prevent uart idling during suspend
to provide debug prints.
Power domain hooks can idle uarts if left enabled during system wide suspend
so re-use the omap_device_disable_idle_on_suspend API's to ensure console_uart
is not idled during suspend.
omap_device_disable_idle_on_suspend API was used on all uarts since the uart
driver was not runtime adapted, now with runtime adaptation we can re-use this
API only for no_console_suspend use cases.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Omap-uart can be used as console uart to print early boot messages using
earlyprintk so for console uart prevent hwmod reset or idling during bootup.
Identify omap-uart used as console and avoid idling rather than preventing
all omap-uarts from idling during bootup. Update the comments for the same.
Remove the uart idling and enabling back using hwmod_idle/omap_device_enable
for all uarts that where left enabled from boot to set the hwmod framework
state machine right. This need not be taken care any more serial.c rather
can be handled within the hwmod framework.
Reference: http://www.spinics.net/lists/linux-omap/msg60300.html
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Reuse the num_uarts variable itself to count number of uarts.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
When using DMA there are two timeouts defined. The first timeout,
rx_timeout, is really a polling rate in which software polls the
DMA status to see if the DMA has finished. This is necessary for
the RX side because we do not know how much data we will receive.
The secound timeout, RX_TIMEOUT, is a timeout after which the
DMA will be stopped if no more data is received. To make this
clearer, rename rx_timeout as rx_poll_rate and rename the
function serial_omap_rx_timeout() to serial_omap_rxdma_poll().
The OMAP-Serial driver defines an RX_TIMEOUT of 3 seconds that is
used to indicate when the DMA for UART can be stopped if no more
data is received. The value is a global definition that is applied
to all instances of the UART.
Each UART may be used for a different purpose and so the timeout
required may differ. Make this value configurable for each UART so
that this value can be optimised for power savings.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: Kevin Hilman <khilman@ti.com>
The following UART parameters are defined within the UART driver:
1). Whether the UART uses DMA (dma_enabled), by default set to 0
2). The size of dma buffer (set to 4096 bytes)
3). The time after which the dma should stop if no more data is received.
4). The auto suspend delay that will be passed for pm_runtime_autosuspend
where uart will be disabled after timeout
Different UARTs may be used for different purpose such as the console,
for interfacing bluetooth chip, for interfacing to a modem chip, etc.
Therefore, it is necessary to be able to customize the above settings
for a given board on a per UART basis.
This change allows these parameters to be configured from the board file
and allows the parameters to be configured for each UART independently.
If a board does not define its own custom parameters for the UARTs, then
use the default parameters in the structure "omap_serial_default_info".
The default parameters are defined to be the same as the current settings
in the UART driver to avoid breaking the UART for any cuurnelty supported
boards. By default, make all boards use the default UART parameters.
Signed-off-by: Deepak K <deepak.k@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: Kevin Hilman <khilman@ti.com>
From the runtime callbacks enable hwmod wakeups for uart which will
internally enable io-pad wakeups for uarts if they have rx-pad pins
set as wakeup capabale.
Use the io-ring wakeup mechanism after uart clock gating and leave
the PM_WKST set for uart to default reset values cleanup the
code in serial.c which was handling PM_WKST reg.
Irq_chaing(PRM_DRIVER) is used to wakeup uart after uart clocks are gated
using pad wakeup mechanism.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: Kevin Hilman <khilman@ti.com>
Move the errata handling mechanism from serial.c to omap-serial file
and utilise the same func in driver file.
Errata i202, i291 are moved to be handled with omap-serial
Moving the errata macro from serial.c file to driver header file
as from on errata will be handled in driver file itself.
Corrected errata id from chapter reference 2.15 to errata id i291.
Removed errata and dma_enabled fields from omap_uart_state struct
as they are no more needed with errata handling done within omap-serial.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Avoid unconditional context restore every time we gate uart
clocks. Check whether context loss happened based on which
we can context restore uart regs from uart_port structure.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: Kevin Hilman <khilman@ti.com>
Remove the uart reset function which is configuring the
TX empty irq which can now be handled within omap-serial driver.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: Kevin Hilman <khilman@ti.com>
Remove context save function from serial.c and move context restore
function to omap-serial. Remove all regs stored in omap_uart_state
for contex_save/restore, reg read write funcs used in context_save/restore,
io_addresses populated for read/write funcs.
Clock gating mechanism was done in serial.c and had no info on uart state
thus we needed context save and restore in serial.c
With runtime conversion and clock gating done within uart driver
context restore can be done from regs value available from uart_omap_port
structure.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: Kevin Hilman <khilman@ti.com>
The mapbase (start_address), membase(io_remap cookie) part of
pdata struct omap_uart_port_info are removed as this should be
derived within driver.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: Kevin Hilman <khilman@ti.com>
Padconf wakeup is used to wakeup uart after uart fclks/iclks are gated.
Rx-Pad wakeup was done by writing to rx-pad offset value populated in
serial.c idle_init. Remove the direct reading and writing into rx pad.
Remove the padconf field part of omap_uart_state struct and pad offsets
populated.
Now with mux framework support we can use mux_utilities
along with hmwod framework to handle io-pad configuration and enable rx-pad
wake-up mechanism.
To avoid breaking any board support add default mux data for all uart's
if mux info is not passed from board file.
With the default pads populated in serial.c wakeup capability for
rx pads is set, this can be used to enable uart_rx io-pad wakeup from
hwmod framework. The pad values in 3430sdp/4430sdp/omap4panda board file
are same as the default pad values populated in serial.c. Remove pad values
from 3430sdp/4430sdp/omap4panda board file and use the default pads
from serial.c file.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Currently we use a shared irq handler to identify uart activity and then
trigger a timer. By default the timeout value is zero and can be set or
modified from sysfs. If there was no uart activity for the period set
through sysfs, the timer will expire and call timer handler this will
set a flag can_sleep using which decision to gate uart clocks can be taken.
Since the clock gating mechanism is outside the uart driver, we currently
use this mechanism. In preparation to runtime implementation for omap-serial
driver we can cleanup this mechanism and use runtime API's to gate uart clocks.
Removes the following:
* timer related info from local uart_state struct
* the code used to set timeout value from sysfs.
* irqflags used to set shared irq handler.
* un-used function omap_uart_check_wakeup.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: Kevin Hilman <khilman@ti.com>
We had been using traditional 8250 driver as uart console driver
prior to omap-serial driver. Since we have omap-serial driver
in mainline kernel for some time now it has been used as default
uart console driver on omap2+ platforms. Remove 8250 support for
omap-uarts.
Serial_in and serial_out override for 8250 serial driver is also
removed. Empty fifo read fix is already taken care with omap-serial
driver with data ready bit check from LSR reg before reading RX fifo.
Also waiting for THRE(transmit hold reg empty) is done with wait_for_xmitr
in omap-serial driver.
Serial_in/out overrides are not neceesary for omap-serial driver
and things that are taken with omap-serial driver are removed here.
Remove headers that were necessary to support 8250 support
and remove all config bindings done to keep 8250 backward compatibility
while adding omap-serial driver. Remove omap_uart_reset needed for
8250 autoconf.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
In preparation to UART runtime conversion remove uart specific calls
from pm24xx/34xx files and their definition from serial.c
These func calls will no more be used with upcoming uart runtime design.
1.) omap_uart_prepare_suspend :- can be taken care with driver suspend hooks.
2.) omap_uart_enable_irqs :- Used to enable/disable uart irq's in suspend
path from PM code, this is removed as same is handled by
uart_suspend_port/uart_resume_port in omap-serial driver which will
do an port_shutdown on suspend freeing irq and port_startup on resume
enabling back irq.
3.) Remove prepare_idle/resume_idle calls used to gate uart clocks.
UART clocks can be gated within driver using runtime funcs
and be woken up using irq_chaining from omap_prm driver.
4.) Remove console_locking from idle path as clock gating is done withing
driver itself with runtime API. Remove is_suspending check used to acquire
console_lock.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Commit 10299e2e4e (ARM: RX-51:
Enable isp1704 power on/off) added power management for isp1704.
However, the transceiver should be powered on by default,
otherwise USB doesn't work at all for networking during
boot.
All kernels after v3.0 are affected.
Cc: stable@kernel.org
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Reviewed-by: Sebastian Reichel <sre@debian.org>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adding musb support in ti816 EVM board file.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adding ti81xx_musb_phy_power() which will be used by musb driver through
its function pointer in board_data.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Added musb support for ti81xx platform which has two instances of musb
interface and uses CPPI4.1 DMA. The current patch set adds support for
single instance and in PIO mode only.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds minimal support and build configuration for TI8148 EVM. Also
adds support for low level debugging on UART1 console on the EVM.
Note that existing TI8168 EVM file (board-ti8168evm.c) is updated with machine
info for TI8148 EVM.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP4 SDP/Blaze boards have onboard digital microphones.
Register the platform device for the dmic-codec to be
able to use the microphones.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add memory timing info regarding the 200 MHz memory in sdram-nokia.
Note that 100 MHz mode uses these same timings too.
Signed-off-by: Igor Dmitriev <ext-dmitriev.igor@nokia.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
[tony@atomide.com: updated comments for 100 MHz timings]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable TSC2005 touchscreen driver on the RX-51 board by providing the
needed platform data.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Reviewed-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP pin mux configuration API has been used incorrectly resulting
in wrong mux mode set for several DSS pins.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
USB hub is not functional until is reset.
Reset the USB hub on SB-T35.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
[tony@atomide.com: updated subject]
Signed-off-by: Tony Lindgren <tony@atomide.com>
TWL4030 audio codec is not being registered if no platform data is
supplied. Provide platform data for the TWL4030 audio codec.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
[tony@atomide.com: updated subject]
Signed-off-by: Tony Lindgren <tony@atomide.com>
cm-t35 DSS suplies are connected to VIO.
In fact, TPS65930 does not have VPLL2.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
[tony@atomide.com: updated subject]
Signed-off-by: Tony Lindgren <tony@atomide.com>
ads7846 driver fails to find the regulator supply and
as a result the touchscreen is not working.
Fix this by adding a regulator supply for the ads7846 driver.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
[tony@atomide.com: updated subject]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds cpu type, macros for identification of TI814X device.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
[tony@atomide.com: left out CK_TI814X for now]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch updates existing macros, functions used for TI816X, to enable
addition of other SoCs belonging to TI81XX family (e.g., TI814X).
The approach taken is to use TI81XX/ti81xx for code/data going to be common
across all TI81XX devices.
cpu_is_ti81xx() is introduced to handle code common across TI81XX devices.
In addition, ti8168_evm_map_io() is now replaced with ti81xx_map_io() and moved
in mach-omap2/common.c as same will be used for TI814X and is not board
specific.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
allow for the omap4430 es2.3 revision to be recognized in the
omap4_check_revision() function.
most aspects of all omap4430 es2.x versions are identical, however
a number of small variations such as default pullup or pulldown
resistor configurations vary between revisions.
detailed information on silicon errata for omap4430 revisions can
be found at http://focus.ti.com/pdfs/wtbu/swpz009D.pdf
Signed-off-by: David Anders <x0132446@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch updates the common machine specific source files for
support for AM33XX/AM335x with cpu type, macros for identification of
AM33XX/AM335X device.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
[tony@atomide.com: updated for map_io and common.h changes, dropped CK_AM33XX]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch updates the common platform files with AM335X device
support (AM33XX family).
The approach taken in this patch is,
AM33XX device will be considered as OMAP3 variant, and a separate
SoC class created for AM33XX family of devices with a subclass type
for AM335X device, which is newly added device in the family.
This means, cpu_is_omap34xx(), cpu_is_am33xx() and cpu_is_am335x()
checks will return success on AM335X device.
A kernel config option CONFIG_SOC_OMAPAM33XX is added under OMAP3
to include support for AM33XX build.
Also, cpu_mask and RATE_IN_XXX flags have crossed 8 bit hence
struct clksel_rate.flags, struct prcm_config.flags and cpu_mask
are changed to u16 from u8.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Hemant Pedanekar <hemantp@ti.com>
[tony@atomide.com: left out CK_AM33XX for now]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commits 09d28d ("ARM: OMAP: mcbsp: Start generalize omap2_mcbsp_set_clks_src")
and 7bc0c4 ("ARM: OMAP: mcbsp: Start generalize signal muxing functions")
incorrectly set two struct omap_mcbsp_platform_data fields after
omap_device_build_ss and kfree calls.
Fix this by moving these pdata assignments before those calls.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Reported-by: NeilBrown <neilb@suse.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 1376d92f9 "usb: musb: allow musb and glue layers to be modules"
made the USB_MUSB_TUSB6010 option modular, but actually building
the driver as a module does not work, so various randconfig builds
actually fail. This changes all code that depends on the
option to also check for modular builds, and exports the necessary
symbols.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add support for base-board MMC slot
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Abhilash K V <abhilash.kv@ti.com>
[tony@atomide.com: updated subject]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following error message which appears
while intializing MMC1 on the AM3517 EVM base-board:
mmc0: host doesn't support card's voltages
mmc0: error -22 whilst initialising SD card
The ocr_mask, which enumerates the volatges supported by the
MMC card was not being indicated before, assuming that a separate
Vcc regulator maybe another controllable regulator driver would be
doing this. This patch statically specifies a subset of the voltages
supported by the MMC driver, which are provided by the current fixed
voltage regulator on AM3517 EVM.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Abhilash K V <abhilash.kv@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Devkit8000 uses a TWL4030 pin for card detection.
Thats why the error:
_omap_mux_init_gpio: Could not set gpio192
occurs.
This patch checks that the pin is on OMAP before
calling omap_mux_init_gpio.
Signed-off-by: Thomas Weber <weber@corscience.de>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM35x MMC 2 controller has internal clock loopback setting which cannot
be utilized without this patch and thus SDIO devices connected to this
controller and depend on this setting will fail to initialize.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Declare support for keeping the power of the wlan chip
while suspended. this is needed for Wakeup-On-Wireless.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add pm_caps field to omap2_hsmmc_info and omap_mmc_slot_data
structs, so we will be able to indicate mmc pm capabilities
in the board file.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Save VFP CPU context using CPU PM notifier chain. VFP context
is lost when CPU hits OFF state.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
CPU local timer(TWD) stops when the CPU is transitioning into
deeper C-States. Since these timers are not wakeup capable, we
need the wakeup capable global timer to program the wakeup time
depending on the next timer expiry.
It can be handled by registering a global wakeup capable timer along
with local timers marked with (mis)feature flag CLOCK_EVT_FEAT_C3STOP.
Then notify the clock events layer from idle code using
CLOCK_EVT_NOTIFY_BROADCAST_ENTER/EXIT).
ARM local timers are already marked with C3STOP feature. Add the
notifiers to OMAP4 CPU idle code for the broadcast entry and exit.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Add OMAP4 CPUIDLE support. CPU1 is left with defualt idle and
the low power state for it is managed via cpu-hotplug.
This patch adds MPUSS low power states in cpuidle.
C1 - CPU0 ON + CPU1 ON + MPU ON
C2 - CPU0 OFF + CPU1 OFF + MPU CSWR
C3 - CPU0 OFF + CPU1 OFF + MPU OSWR
OMAP4460 onwards, MPUSS power domain doesn't support OFF state any more
anymore just like CORE power domain. The deepest state supported is OSWr.
Ofcourse when MPUSS and CORE PD transitions to OSWR along with device
off mode, even the memory contemts are lost which is as good as
the PD off state.
On OMAP4 because of hardware constraints, no low power states are
targeted when both CPUs are online and in SMP mode. The low power
states are attempted only when secondary CPU gets offline to OFF
through hotplug infrastructure.
Thanks to Nicole Chalhoub <n-chalhoub@ti.com> for doing exhaustive
C-state latency profiling.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
On OMAP4 SOC, intecronnects has many write buffers in the async bridges
and they need to be drained before CPU enters into standby state.
Patch 'OMAP4: PM: Add CPUX OFF mode support' added CPU PM support
but OMAP errata i688 (Async Bridge Corruption) needs to be taken
care to avoid issues like system freeze, CPU deadlocks, random
crashes with register accesses, synchronisation loss on initiators
operating on both interconnect port simultaneously.
As per the errata, if a data is stalled inside asynchronous bridge
because of back pressure, it may be accepted multiple times, creating
pointer misalignment that will corrupt next transfers on that data
path until next reset of the system (No recovery procedure once
the issue is hit, the path remains consistently broken).
Async bridge can be found on path between MPU to EMIF and
MPU to L3 interconnect. This situation can happen only when the
idle is initiated by a Master Request Disconnection (which is
trigged by software when executing WFI on CPU).
The work-around for this errata needs all the initiators
connected through async bridge must ensure that data path
is properly drained before issuing WFI. This condition will be
met if one Strongly ordered access is performed to the
target right before executing the WFI. In MPU case, L3 T2ASYNC
FIFO and DDR T2ASYNC FIFO needs to be drained. IO barrier ensure
that there is no synchronisation loss on initiators operating
on both interconnect port simultaneously.
Thanks to Russell for a tip to conver assembly function to
C fuction there by reducing 40 odd lines of code from the patch.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Richard Woodruff <r-woodruff2@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds the MPUSS OSWR (Open Switch Retention) support. The MPUSS
OSWR configuration is as below.
- CPUx L1 and logic lost, MPUSS logic lost, L2 memory is retained
OMAP4460 onwards, MPUSS power domain doesn't support OFF state any more
anymore just like CORE power domain. The deepest state supported is OSWR.
On OMAP4430 secure devices too, MPUSS off mode can't be used because of
a bug which alters Ducati and Tesla states. Hence MPUSS off mode as an
independent state isn't supported on OMAP44XX devices.
Ofcourse when MPUSS power domain transitions to OSWR along
with device off mode, it eventually hits off state since memory
contents are lost.
Hence the MPUSS off mode independent state is not attempted without
device off mode. All the necessary infrastructure code for MPUSS
off mode is in place as part of this series.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
When MPUSS hits off-mode, L2 cache is lost. This patch adds L2X0
necessary maintenance operations and context restoration in the
low power code.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Add WakeupGen and secure GIC low power support to save and restore
it's registers. WakeupGen Registers are saved to pre-defined SAR RAM layout
and the restore is automatically done by hardware(ROM code) while coming
out of MPUSS OSWR or Device off state. Secure GIC is saved using secure
API and restored by hardware like WakeupGen.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
With OMAP4 suspend, idle and hotplug series, we no longer need
do_wfi() macro.
Remove the same.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds MPUSS(MPU Sub System) power domain
CSWR(Close Switch Retention) support to system wide suspend.
For MPUSS power domain to hit retention(CSWR or OSWR), both
CPU0 and CPU1 power domains need to be in OFF or DORMANT state,
since CPU power domain CSWR is not supported by hardware
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Default arch_idle() isn't good enough for OMAP4 because of aync bridge errata
and necessity of NOPs post WFI to avoid speculative prefetch aborts.
Hence Use OMAP4 custom omap_do_wfi() hook for default idle.
Later in the series, async bridge errata work-around patch updates the
omap_do_wfi() with necessary interconnects barriers.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The SGI(Software Generated Interrupts) are not wakeup capable from
low power states. This is known limitation on OMAP4 and needs to be
worked around by using software forced clockdomain wake-up. CPU0 forces
the CPU1 clockdomain to software force wakeup.
More details can be found in OMAP4430 TRM - Version J
Section :
4.3.4.2 Power States of CPU0 and CPU1
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Program non-boot CPUs to hit lowest supported power state
when it is off-lined using cpu hotplug framework.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Remove the __INIT from omap_secondary_startup() so that it can
be re-used for CPU hotplug.
While at this, remove the un-used AUXBOOT register reference.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds the CPU0 and CPU1 off mode support. CPUX close switch
retention (CSWR) is not supported by hardware design.
The CPUx OFF mode isn't supported on OMAP4430 ES1.0
CPUx sleep code is common for hotplug, suspend and CPUilde.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
OMAP WakeupGen is the interrupt controller extension used along
with ARM GIC to wake the CPU out from low power states on
external interrupts.
The WakeupGen unit is responsible for generating the wakeup event
from the incoming interrupts and enable bits. It is implemented
in the MPU always ON power domain. During normal operation,
WakeupGen delivers the external interrupts directly to the GIC.
WakeupGen specification has one restriction as per Veyron version 1.6.
It is SW responsibility to program interrupt enabling/disabling
coherently in the GIC and in the WakeupGen enable registers. That is, a
given interrupt for a given CPU is either enable at both GIC and WakeupGen,
or disable at both, but no mix. That's the reason the WakeupGen is
implemented as an extension of GIC.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Allocate the memory to save secure ram context which needs
to be done when MPU is hitting OFF mode.
The ROM code expects a physical address to this memory
and hence use memblock APIs to reserve this memory as part
of .reserve() callback. Maximum size as per secure RAM requirements
is allocated.
To keep omap1 build working, omap-secure.h file is created
under plat-omap directory.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
On OMAP secure/emulation devices, certain APIs are exported by secure
code. Add an infrastructure so that relevant operations on secure
devices can be implemented using it.
While at this, rename omap44xx-smc.S to omap-smc.S since the common APIs
can be used on other OMAP's too.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Initialise hardware supervised mode for all clockdomains if it's
supported. Initiate sleep transition for other clockdomains,
if they are not being used.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
On OMAP4430 ES1.0, Power Management features are not supported.
Avoid omap4_pm_init() on ES1.0 silicon so that we can continue
to use same kernel binary to boot on all OMAP4 silicons.
The ES1.0 boot failure with OMAP4 PM series was because of
the clockdomain initialisation code. Hardware supervised
clockdomain mode isn't functional for all clockdomains
on OMAP4430 ES1.0 silicon so avoid the same.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reported-by: Kevin Hilman <khilman@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
As per OMAP4430 TRM, the dynamic dependency between MPUSS -> EMIF
and MPUSS -> L4PER/L3_* and DUCATI -> L3_* clockdomains is enable
by default. Refer register CM_MPU_DYNAMICDEP description for details.
But these dynamic dependencies doesn't work as expected. The hardware
recommendation is to enable static dependencies for above clockdomains.
Without this, system locks up or randomly crashes.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds SAR RAM support on OMAP4430. SAR RAM used to save
and restore the HW context in low power modes.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch exports APIs to get base address for GIC
distributor, CPU interface, SCU and PL310 L2 Cache which
are used in OMAP4 PM code.
This was suggested by Kevin Hilman <khilman@ti.com> during
OMAP4 PM code review.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
OMAP4 L2X0 initialisation code uses BUG_ON() for the ioremap()
failure scenarios.
Use WARN_ON() instead and allow graceful function exits.
This was suggsted by Kevin Hilman <khilman@ti.com> during
OMAP4 PM code review.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
ARM restart changes needed changes to common.h to make it local.
This conflicted with v3.2-rc4 DSS related hwmod changes that
git mergetool was not able to handle.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix the below build break by including common.h
arch/arm/mach-omap2/cpuidle34xx.c: In function 'omap3_enter_idle':
arch/arm/mach-omap2/cpuidle34xx.c:117: error: implicit declaration of function 'omap_irq_pending'
make[1]: *** [arch/arm/mach-omap2/cpuidle34xx.o] Error 1
make: *** [arch/arm/mach-omap2] Error 2
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix the build break by adding the necessary irq functions to
common header.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix below compilation failure on mainline kernel 3.2-rc1
when omap_l3_noc.c is built as module.
arch/arm/mach-omap2/omap_l3_noc.c:240: error: expected ',' or ';' before 'MODULE_DEVICE_TABLE'
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The file arch/arm/mach-omap2/io.h is empty, so we can remove it.
Signed-off-by: Thomas Weber <weber@corscience.de>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch selects ARM_AMBA if OMAP3_EMU is defined because
OC_ETM depends on ARM_AMBA, so fix the link failure[1].
[1],
arch/arm/kernel/built-in.o: In function `etm_remove':
/home/tom/git/omap/linux-2.6-omap/arch/arm/kernel/etm.c:609: undefined
reference to `amba_release_regions'
arch/arm/kernel/built-in.o: In function `etb_remove':
/home/tom/git/omap/linux-2.6-omap/arch/arm/kernel/etm.c:409: undefined
reference to `amba_release_regions'
arch/arm/kernel/built-in.o: In function `etm_init':
/home/tom/git/omap/linux-2.6-omap/arch/arm/kernel/etm.c:640: undefined
reference to `amba_driver_register'
/home/tom/git/omap/linux-2.6-omap/arch/arm/kernel/etm.c:646: undefined
reference to `amba_driver_register'
/home/tom/git/omap/linux-2.6-omap/arch/arm/kernel/etm.c:648: undefined
reference to `amba_driver_unregister'
arch/arm/kernel/built-in.o: In function `etm_probe':
/home/tom/git/omap/linux-2.6-omap/arch/arm/kernel/etm.c:545: undefined
reference to `amba_request_regions'
/home/tom/git/omap/linux-2.6-omap/arch/arm/kernel/etm.c:595: undefined
reference to `amba_release_regions'
arch/arm/kernel/built-in.o: In function `etb_probe':
/home/tom/git/omap/linux-2.6-omap/arch/arm/kernel/etm.c:347: undefined
reference to `amba_request_regions'
/home/tom/git/omap/linux-2.6-omap/arch/arm/kernel/etm.c:392: undefined
reference to `amba_release_regions'
arch/arm/mach-omap2/built-in.o: In function `emu_init':
/home/tom/git/omap/linux-2.6-omap/arch/arm/mach-omap2/emu.c:62:
undefined reference to `amba_device_register'
/home/tom/git/omap/linux-2.6-omap/arch/arm/mach-omap2/emu.c:63:
undefined reference to `amba_device_register'
make: *** [.tmp_vmlinux1] Error 1
making modules
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix a bug which has been on this driver since
it was added by the original commit 984aa6db
which would never clear IRQSTATUS bits.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Current code registers voltage layer details for TWL PMIC even when a TWL
has not been registered. Fix this to only register the TWL with voltage
layer when the TWL PMIC is initialized by board-level code.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
The address spaces, irqs and dma reqs count APIs return the
number of corresponding entries in a hwmod including a additional
null value or a -1 terminator in the structure introduced recently.
More information here:
- 212738a4: omap_hwmod: use a terminator record with omap_hwmod_mpu_irqs
arrays
- 78183f3f: omap_hwmod: use a null structure record to terminate
omap_hwmod_addr_space arrays
- bc614958: omap_hwmod: use a terminator record with omap_hwmod_dma_info
arrays
The issue with irqs and dma info was originally reported by Benoit Cousson.
The devices which have multiple hwmods and use device_build_ss are
broken with this, as their resources are populated with a extra null
value, subsequently the probe fails. So fix the API not to include
the array terminator in the count.
Reported-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimar@ti.com>
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Conflicts:
arch/arm/mach-omap2/board-4430sdp.c
arch/arm/mach-omap2/board-omap4panda.c
arch/arm/mach-omap2/include/mach/omap4-common.h
arch/arm/plat-omap/include/plat/irqs.h
The changes to omap4-common.h were moved to arch/arm/mach-omap2/common.h
and the other trivial conflicts resolved. The now empty ifdef in irqs.h
was also eliminated.
A generic version should replace this later.
As io.c has become nearly empty, omap_init_consistent_dma_size() is moved
into common.c so that io.c can be removed entirely.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Tested-by: Kevin Hilman <khilman@ti.com>
As suggested by Russell King - ARM Linux <linux@arm.linux.org.uk>,
there's no need to keep local prototypes in non-local headers.
Add mach-omap1/common.h and mach-omap2/common.h and move the
local prototypes there from plat/common.h and mach/omap4-common.h.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now that MULTI_IRQ_HANDLER is selected by all the in-tree
GIC users, make it mandatory and remove the unused macros.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Convert the omap2plus platforms to be using CONFIG_MULTI_IRQ_HANDLER.
Each machine is modified to provide either omap2_intc_handle_irq(),
omap3_intc_handle_irq() or gic_handle_irq().
This allows for a major cleanup, removing the MULTI_OMAP setup
from the interrupt path.
Tested on both Panda and IGEPv2 (single kernel image)
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Provide the OMAP2/3 IRQ code with low level handlers that can be used
by platforms using CONFIG_MULTI_IRQ_HANDLER. Though the handlers are
written in C, the compiled code looks very similar to its assembly
counterpart (at least with my gcc 4.4.1).
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Resetting DISPC when a DISPC output is enabled causes the DSS to go into an
inconsistent state. Thus if the bootloader has enabled a display, the hwmod code
cannot reset the DISPC module just like that, but the outputs need to be
disabled first.
Add function dispc_disable_outputs() which disables all active overlay manager
and ensure all frame transfers are completed.
Modify omap_dss_reset() to call this function and clear DSS_CONTROL,
DSS_SDI_CONTROL and DSS_PLL_CONTROL so that DSS is in a clean state when the
DSS2 driver starts.
This resolves the hang issue(caused by a L3 error during boot) seen on the
beagle board C3, which has a factory bootloader that enables display. The issue
is resolved with this patch.
Thanks to Tomi and Sricharan for some additional testing.
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: R, Sricharan <r.sricharan@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
[paul@pwsan.com: restructured code, removed omap_{read,write}l(), removed
cpu_is_omap*() calls and converted to dev_attr]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch adds a custom DSS reset function used on OMAPs from OMAP2
forward.
The function doesn't actually do a reset, it only waits for the reset to
complete. The reason for this is that on OMAP4 there is no possibility
to do a SW reset, and on OMAP2/3 doing a SW reset for dss_core resets
all the other DSS modules also, thus breaking the HWMOD model where
every DSS module is handled independently.
This fixes the problem with DSS reset on OMAP4, caused by the fact that
because there's no SW reset for dss_core on OMAP4, the HWMOD framework
doesn't try to reset dss_core and thus the DSS clocks were never enabled
at the same time. This causes causes the HWMOD reset to fail for
dss_dispc and dss_rfbi.
The common reset function will also allow us to fix another problem in
the future: before doing a reset we need to disable DSS outputs, which
are in some cases enabled by the bootloader, as otherwise DSS HW seems
to get more or less stuck, requiring a power reset to recover.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[paul@pwsan.com: modified to build arch/arm/mach-omap2/display.o
unconditionally to avoid an error when !CONFIG_OMAP2_DSS]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
OMAP2/3 dss_core has a reset status flag in sysstatus register. Add
SYSS_HAS_RESET_STATUS flag to HWMOD data so it can be used.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The OMAP4 HWMOD data currently contains errors with DSS clocks:
dss_hdmi and dss_venc have their main_clks wrong. The clocks should be
dss_48mhz_clk and dss_tv_clk, respectively.
These problems were temporarily fixed with the DSS patches
9ede365aa6 ("HACK: OMAP: DSS2: clk hack
for OMAP2/3"), and df5d3ed23c ("OMAP:
DSS2: HDMI: fix hdmi clock name"), which can be reverted after this
patch.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
DSS needs all DSS clocks to be enabled to be able to finish reset
properly. Before v3.1-rc1 the omapdss driver was managing clocks and
resets correctly. However, when omapdss started using runtime PM at
v3.1-rc1, the responsibility for the reset moved to HWMOD framework.
HWMOD framework does not currently enable all the DSS clocks when
resetting the DSS hardware. This causes the HWMOD frameworks boot-time
reset to fail, possibly leaving the DSS hardware in undefined state.
This patch sets HWMOD_CONTROL_OPT_CLKS_IN_RESET for dss_core. The flag
is actually not used on OMAP4, because dss_core hardware does not have
soft-reset functionality and thus the HWMOD framework never resets nor
waits for the reset to finish.
However, while the flag is not strictly needed currently, I think it
represents the HW correctly: all the DSS clocks should be enabled after
power-on to allow DSS hardware to finish its reset.
A custom reset function will be added in the following patches which
manages this correctly for OMAP4.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Remove the dss_dss_clk from dss_core's opt-clocks. dss_dss_clk already
defined as the dss main_clk, and thus is not needed as an opt-clock.
Remove opt-clocks for dss_dispc, as dispc only uses the main_clk.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
