Armada-3700's uart is a simple serial port, which doesn't
support. Configuring the modem control lines. The uart port has a 32
bytes Tx FIFO and a 64 bytes Rx FIFO
The uart driver implements the uart core operations. It also support the
system (early) console based on Armada-3700's serial port.
Known Issue:
The uart driver currently doesn't support clock programming, which means
the baud-rate stays with the default value configured by the bootloader
at boot time
[gregory.clement@free-electrons.com: Rewrite many part which are too long
to enumerate]
Signed-off-by: Wilson Ding <dingwei@marvell.com>
Signed-off-by: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable support for registering this device using the device tree.
Device tree node example for registering Goldfish TTY device :
goldfish_tty@1f004000 {
interrupts = <0xc>;
reg = <0x1f004000 0x1000>;
compatible = "google,goldfish-tty";
};
Signed-off-by: Miodrag Dinic <miodrag.dinic@imgtec.com>
Signed-off-by: Jin Qian <jinqian@android.com>
Signed-off-by: Alan <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce a dt property, ti,no-idle, that prevents an IP to idle at any
point. This is to handle Errata i877, which tells that GMAC clocks
cannot be disabled.
Acked-by: Roger Quadros <rogerq@ti.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Update devicetree documention for lpc1850-scu with the new
nxp,gpio-pin-interrupt property.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
is actually "active high". Thanks for Troy Kisky for pointing
that out.
Since the patch is in linux-next, this patch is incremental and doesn't
replace the original patch.
Signed-off-by: Bernhard Walle <bernhard@bwalle.de>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ath.git patches for 4.6. Major changes:
ath10k
* dt: add bindings for ipq4019 wifi block
* start adding support for qca4019 chip
ath9k
* add device ID for Toshiba WLM-20U2/GN-1080
* allow more than one interface on DFS channels
Although most of USB devices are hot-plug's, there are still some devices
are hard wired on the board, eg, for HSIC and SSIC interface USB devices.
If these kinds of USB devices are multiple functions, and they can supply
other interfaces like i2c, gpios for other devices, we may need to
describe these at device tree.
In this commit, it uses "reg" in dts as physical port number to match
the phyiscal port number decided by USB core, if they are the same,
then the device node is for the device we are creating for USB core.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for the Murata NCP15XH103 thermistor series.
Signed-off-by: Joseph McNally <jmcna06@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Change iio_hwmon nodes to use hypen in node names instead of
underscore.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The FMan contains internal PHY devices used for SGMII connections
to external PHYs. When these PHYs are in use a reference is needed
for both the external PHY and the internal one. For the external
PHY phy-handle provides the reference. For the internal PHY a new
handle is required.
In dTSEC, the internal PHY is a TBI (Ten Bit Interface) PHY,
the handle used will be tbi-handle.
In mEMAC, the internal PHY is a PCS (Physical Coding Sublayer) PHY,
the handle used will be pcsphy-handle.
Signed-off-by: Igal Liberman <igal.liberman@freescale.com>
Signed-off-by: Scott Wood <oss@buserror.net>
RCPM is the Run Control and Power Management module performs all
device-level tasks associated with device run control and power
management.
Add this for freescale powerpc platform and layerscape platform.
Signed-off-by: Chenhui Zhao <chenhui.zhao@freescale.com>
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
[scottwood: s/pointer/phandle and "disabled" status from example]
Signed-off-by: Scott Wood <oss@buserror.net>
Currently the binding is only made of the compatible string.
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas sound device has CTU (= Channel Transfer Unit), and
sound card needs its support.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
this patch add compatible for rk3366/rk3368/rk3399 spdif,
these three spdifs share the same type.
Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is almost all under drivers/usb/dwc2/. Many
changes to the host side implementation of dwc2 have
been done by Douglas Anderson.
We also have USB 3.1 support added to the Gadget
Framework and, because of that work, dwc3 got
support to Synopsys new DWC_usb31 IP core.
Other than these 2 important series, we also have
the usual collection of non-critical fixes,
Documentation updates, and minor changes all over
the place.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=vivP
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.6' of http://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb changes for v4.6 merge window
This is almost all under drivers/usb/dwc2/. Many
changes to the host side implementation of dwc2 have
been done by Douglas Anderson.
We also have USB 3.1 support added to the Gadget
Framework and, because of that work, dwc3 got
support to Synopsys new DWC_usb31 IP core.
Other than these 2 important series, we also have
the usual collection of non-critical fixes,
Documentation updates, and minor changes all over
the place.
Bring in updates to roraty encoder driver switching it away from legacy
platform data and over to generic device properties and adding support
for encoders using more than 2 GPIOs.
Add support for Lantiq ARX and XRX SoC families to the dwc2 driver.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Add fallback compatibility strings for R-Car Gen2 and Gen3.
This is in keeping with the fallback scheme being adopted wherever
appropriate for drivers for Renesas SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By simply setting vref-mv to 0 the internal reference will be used.
Document that!
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Rob Herring <robh@kernel.org>
There are two distinct RealView EB system controller that we need
to detect and handle because their register layout differ
slightly.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rob Herring <robh@kernel.org>
The binding documentation uses both "uVolt" and "uV" for micro-volt.
Improve consistency by settling on "uV".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rob Herring <robh@kernel.org>
This reverts commit 82c2ffeb21 ("[media] tvp5150: document input
connectors DT bindings") since the DT binding is too device driver
specific and should instead be more generic and use the bindings
in Documentation/devicetree/bindings/display/connector/ and linked
to the tvp5150 using the OF graph port and endpoints.
There are still ongoing discussions about how the input connectors
will be supported by the Media Controller framework so until that
is settled, it is better to revert the connectors portion of the
bindings to avoid known to be broken bindings docs to hit mainline.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add device tree bindings to the Goldfish virtual platform battery drivers.
Signed-off-by: Greg Hackmann <ghackmann@google.com>
Signed-off-by: Jin Qian <jinqian@android.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This changes how the used gpios are stored (i.e. a struct gpio_descs
instead of two struct gpio_desc) and as with >2 gpios the states are
numbered differently the function rotary_encoder_get_state returns
unencoded numbers instead of grey encoded numbers before. The latter has
some implications on how the returned value is used and so the change is
bigger than one might expect at first.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch restructures the DMA bus settings and this is done
by introducing a new platform structure used for programming
the AXI Bus Mode Register inside the DMA module.
This structure can be populated from device-tree as documented in the
binding txt file.
After initializing the DMA, the AXI register can be optionally tuned
for platform drivers based.
This patch also reworks some parameters to make coherent the DMA
configuration now that AXI register is introduced.
For example, the burst_len is managed by using the mentioned axi
support above; so the snps,burst-len parameter has been removed.
It makes sense to provide the AAL parameter from DT to Address-Aligned
Beats inside the Register0 and review the PBL settings when initialize
the engine.
For PCI glue, rebuilding the story of this setting, it
was added to align a configuration so not for fixing some
known problem. No issue raised after this patch.
It is safe to use the default burst length instead of
tuning it to the maximum value
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add common DT property for regulator node to support of
active discharge enable/disable configuration of regulator.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is the DPCM based machine driver with rt5650 and rt5514.
Signed-off-by: Koro Chen <koro.chen@mediatek.com>
Signed-off-by: PC Liao <pc.liao@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We want the fixes in here, and others are sending us pull requests based
on this kernel tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Good to see several new contributors in this set - and more generally a
number of new 'faces' over this whole cycle.
Staging movements
* hmc5843
- out of staging.
* periodic RTC trigger
- driver dropped. This is an ancient driver (brings back some memories ;)
that was always somewhat of a bodge. Originally there was a driver that
never went into mainline that supported large numbers of periodict timers
on the PXA270 via this route. Discussions to have a generic periodic
timer subsystem never went anywhere. At the time RTC periodic
interrupts were real - now they are emulated using high resolution
timers so with the HRT driver this has become pointless.
New device support
* mpu6050 driver
- Add support for the mpu6500.
* TI tpl0102 potentiometer
- new driver.
* Vybrid SoC DAC
- new driver. The ADC on this SoC has been supported for a while, this
adds a separate driver for the DAC.
New Features
* hmc5844
- Attributes to configure the bias current (typically part of a self test)
This could be done before via a somewhat obscure custom interface.
This at least makes it easy to tell what is going on.
- Document all custom attributes.
* mpu6050
- Add support for calibration offset control and readback.
* ms5611
- power regulator support. This is always one that gets added the
first time someone has a board that needs it. Here it was needed,
hence it was added.
Cleanups / minor fixes
* tree wide
- clean up all the myriad different return values in response to a
failure of i2c_check_functionality. After discussions everyone seemed
happy wiht -EOPNOTSUPP which seems to describe the situation well.
I encouraged a tree wide cleanup to set a good example in future for
this.
* core
- Typos in the iio_event_spec documentation in iio.h
* afe4403
- select REGMAP_SPI to avoid dependency issues
- mark suspend/resume as __maybe_unused to avoid warnings
* afe4404
- mark suspend/resume as __maybe_unused to avoid warnings
* atlas-ph-sensor
- switch the regmap cache type from linear to rbtree to gain reading of
registers on initial startup. It's not immediately obvious, but
regmap flat is meant for high performances cases so doesn't read these
registers.
- use regmap_bulk_read in one case where it was using
i2c_smbus_read_i2c_block_data directly (unlike everything else that was
through regmap).
* ina2xx
- stype cleanups (lots of them!)
* isl29018
- Get the struct device back from regmap rather than storing another
copy of it in the private data. This cleanup makes sense in a number
of other drivers so patches may well follow.
* mpu6050
- style cleanups (lots of them!)
- improved return value handling
- use usleep_range to avoid the usual issues with very short msleeps.
- add some missing documentation.
* ms5611
- use the probed device name for the device rather than the driver name.
- select IIO_BUFFER to avoid dependency issues
* palmas
- drop IRQF_EARLY_RESUME as no longer needed after genirq changes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=rDIQ
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.6c' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Third set of IIO new device support, features and cleanups for the 4.6 cycle.
Good to see several new contributors in this set - and more generally a
number of new 'faces' over this whole cycle.
Staging movements
* hmc5843
- out of staging.
* periodic RTC trigger
- driver dropped. This is an ancient driver (brings back some memories ;)
that was always somewhat of a bodge. Originally there was a driver that
never went into mainline that supported large numbers of periodict timers
on the PXA270 via this route. Discussions to have a generic periodic
timer subsystem never went anywhere. At the time RTC periodic
interrupts were real - now they are emulated using high resolution
timers so with the HRT driver this has become pointless.
New device support
* mpu6050 driver
- Add support for the mpu6500.
* TI tpl0102 potentiometer
- new driver.
* Vybrid SoC DAC
- new driver. The ADC on this SoC has been supported for a while, this
adds a separate driver for the DAC.
New Features
* hmc5844
- Attributes to configure the bias current (typically part of a self test)
This could be done before via a somewhat obscure custom interface.
This at least makes it easy to tell what is going on.
- Document all custom attributes.
* mpu6050
- Add support for calibration offset control and readback.
* ms5611
- power regulator support. This is always one that gets added the
first time someone has a board that needs it. Here it was needed,
hence it was added.
Cleanups / minor fixes
* tree wide
- clean up all the myriad different return values in response to a
failure of i2c_check_functionality. After discussions everyone seemed
happy wiht -EOPNOTSUPP which seems to describe the situation well.
I encouraged a tree wide cleanup to set a good example in future for
this.
* core
- Typos in the iio_event_spec documentation in iio.h
* afe4403
- select REGMAP_SPI to avoid dependency issues
- mark suspend/resume as __maybe_unused to avoid warnings
* afe4404
- mark suspend/resume as __maybe_unused to avoid warnings
* atlas-ph-sensor
- switch the regmap cache type from linear to rbtree to gain reading of
registers on initial startup. It's not immediately obvious, but
regmap flat is meant for high performances cases so doesn't read these
registers.
- use regmap_bulk_read in one case where it was using
i2c_smbus_read_i2c_block_data directly (unlike everything else that was
through regmap).
* ina2xx
- stype cleanups (lots of them!)
* isl29018
- Get the struct device back from regmap rather than storing another
copy of it in the private data. This cleanup makes sense in a number
of other drivers so patches may well follow.
* mpu6050
- style cleanups (lots of them!)
- improved return value handling
- use usleep_range to avoid the usual issues with very short msleeps.
- add some missing documentation.
* ms5611
- use the probed device name for the device rather than the driver name.
- select IIO_BUFFER to avoid dependency issues
* palmas
- drop IRQF_EARLY_RESUME as no longer needed after genirq changes.
Since the related driver (CPG/MSSR driver) only manages the first module
clock, this driver should not handle the HSUSB registers. So, this patch
removes the HSUSB registers handling.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add dt binding documentation for rockchip display port PHY.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch adds a binding that describes the Rockchip eMMC PHYs
found on Rockchip SoCs eMMC interface.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The settings in GPR8 are dependent upon the particular layout of the
hardware platform. As such, they should be configurable via the device
tree.
Look up PHY Tx driver settings from the device tree. Fall back to the
original hard-coded values if they are not specified in the device tree.
Signed-off-by: Justin Waters <justin.waters@timesys.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
If this property is not set, the max packet size is 1023 bytes, and if
the total of packet size for pervious transactions are more than 256 bytes,
it can't accept any transactions within this frame. The use case is single
transaction, but higher frame rate.
If this property is set, the max packet size is 188 bytes, it can handle
more transactions than above case, it can accept transactions until it
considers the left room size within frame is less than 188 bytes, software
needs to make sure it does not send more than 90%
maximum_periodic_data_per_frame. The use case is multiple transactions, but
less frame rate.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
This patch adds the missing compatible strings from ci_hdrc_imx.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
We didn't have a batch last week, so this one is slightly larger.
None of them are scary though, a handful of fixes for small DT pieces,
replacing properties with newer conventions.
Highlights:
- N900 fix for setting system revision
- onenand init fix to avoid filesystem corruption
- Clock fix for audio on Beaglebone-x15
- Fixes on shmobile to deal with CONFIG_DEBUG_RODATA (default y in 4.6)
+ misc smaller stuff.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=xeuW
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"We didn't have a batch last week, so this one is slightly larger.
None of them are scary though, a handful of fixes for small DT pieces,
replacing properties with newer conventions.
Highlights:
- N900 fix for setting system revision
- onenand init fix to avoid filesystem corruption
- Clock fix for audio on Beaglebone-x15
- Fixes on shmobile to deal with CONFIG_DEBUG_RODATA (default y in 4.6)
+ misc smaller stuff"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: Extend info, add wiki and ml for meson arch
MAINTAINERS: alpine: add a new maintainer and update the entry
ARM: at91/dt: fix typo in sama5d2 pinmux descriptions
ARM: OMAP2+: Fix onenand initialization to avoid filesystem corruption
Revert "regulator: tps65217: remove tps65217.dtsi file"
ARM: shmobile: Remove shmobile_boot_arg
ARM: shmobile: Move shmobile_smp_{mpidr, fn, arg}[] from .text to .bss
ARM: shmobile: r8a7779: Remove remainings of removed SCU boot setup code
ARM: shmobile: Move shmobile_scu_base from .text to .bss
ARM: OMAP2+: Fix omap_device for module reload on PM runtime forbid
ARM: OMAP2+: Improve omap_device error for driver writers
ARM: DTS: am57xx-beagle-x15: Select SYS_CLK2 for audio clocks
ARM: dts: am335x/am57xx: replace gpio-key,wakeup with wakeup-source property
ARM: OMAP2+: Set system_rev from ATAGS for n900
ARM: dts: orion5x: fix the missing mtd flash on linkstation lswtgl
ARM: dts: kirkwood: use unique machine name for ds112
ARM: dts: imx6: remove bogus interrupt-parent from CAAM node
Simply document new compatibility string.
As a previous patch adds a generic R-Car Gen2 compatibility string
there appears to be no need for a driver updates.
By documenting these compat stings they may be used in DTSs shipped, for
example as part of ROMs. They must be used in conjunction with the Gen2
fallback compat string. At this time there are no known differences between
the r8a779[234] IP blocks and that implemented by the driver for the Gen2
fallback compat string. Thus there is no need to update the driver as the
use of the Gen2 fallback compat string will activate the correct code in
the current driver while leaving the option for r8a779[234]-specific driver
code to be activated in an updated driver should the need arise.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add fallback compatibility string for R-Car Gen 1 and Gen2.
In the case of Renesas R-Car hardware we know that there are generations of
SoCs, e.g. Gen 1 and Gen 2. But beyond that its not clear what the
relationship between IP blocks might be. For example, I believe that
r8a7779 is older than r8a7778 but that doesn't imply that the latter is a
descendant of the former or vice versa.
We can, however, by examining the documentation and behaviour of the
hardware at run-time observe that the current driver implementation appears
to be compatible with the IP blocks on SoCs within a given generation.
For the above reasons and convenience when enabling new SoCs a
per-generation fallback compatibility string scheme being adopted for
drivers for Renesas SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The cs4271 has three power domains: vd, vl and va.
Enable them all, as long as the codec is in use.
While at it, factored out the reset code into its own function.
Signed-off-by: Pascal Huerst <pascal.huerst@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The new property will allow to specify the range of GIC hwirqs to use for IPIs.
This is an optinal property. We preserve the previous behaviour of allocating
the last 2 * gic_vpes if it's not specified or DT is not supported.
Signed-off-by: Qais Yousef <qais.yousef@imgtec.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: <jason@lakedaemon.net>
Cc: <marc.zyngier@arm.com>
Cc: <jiang.liu@linux.intel.com>
Cc: <linux-mips@linux-mips.org>
Cc: <lisa.parratt@imgtec.com>
Cc: Qais Yousef <qsyousef@gmail.com>
Link: http://lkml.kernel.org/r/1449580830-23652-20-git-send-email-qais.yousef@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
allwinner,sun8i-h3-r-pinctrl was added by
commit ba83a11104 ("pinctrl: sunxi: Add H3 R_PIO controller support")
but the patch was missing proper binding documentation. This patch fixes
this issue.
Signed-off-by: Krzysztof Adamski <k@japko.eu>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add driver support for DAC peripheral on Vybrid SoC.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
- Yet another fix for n900 onenand to avoid corruption. This time to
fix the issue of mounting onenand back and forth between the original
maemo kernel and mainline Linux kernel. And it also seems there will
be two more fixes coming via the MTD tree as issues were discovered
also in the onenand driver during testing.
- Revert tps65217 regulator clean up as it breaks MMC for am335x
variants. The proper way to clean this up is just to rename the
tps65217.dtsi file into tps65217-am335x.dtsi as a similar setup
is used on many am335x boards.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tAiy
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.5/fixes-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Two omap fixes for omaps against v4.5-rc5:
- Yet another fix for n900 onenand to avoid corruption. This time to
fix the issue of mounting onenand back and forth between the original
maemo kernel and mainline Linux kernel. And it also seems there will
be two more fixes coming via the MTD tree as issues were discovered
also in the onenand driver during testing.
- Revert tps65217 regulator clean up as it breaks MMC for am335x
variants. The proper way to clean this up is just to rename the
tps65217.dtsi file into tps65217-am335x.dtsi as a similar setup
is used on many am335x boards.
* tag 'omap-for-v4.5/fixes-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix onenand initialization to avoid filesystem corruption
Revert "regulator: tps65217: remove tps65217.dtsi file"
Signed-off-by: Olof Johansson <olof@lixom.net>
ICP DAS LP-8841 contains a DS-1302 RTC. This driver provides an SPI
master which makes the RTC usable. The driver is not supposed to work
with anything else.
The driver uses the standard MicroWire half-duplex transfer timing.
Master output is set on low clock and sensed by the RTC on the rising
edge. Master input is set by the RTC on the trailing edge and is sensed
by the master on low clock.
Signed-off-by: Sergei Ianovich <ynvich@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the dt bindings for HiSi SAS controller v2 HW.
The main difference in the controller from dt perspective is
interrupts. The v2 controller does not have dedicated fatal and
broadcast interrupts - they are multiplexed on the channel interrupt.
Each SAS v2 controller can issue upto 64 commands (or connection
requests) on the system bus without waiting for a response - this is
know as am-max-transmissions. In hip06, sas controller #1 has a
limitation that it has to limit am-max-transmissions to 32 - this
limitation is due to chip system bus design. It is not anticipated that
any future chip incorporating v2 controller will have such a limitation.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Conflicts:
drivers/net/phy/bcm7xxx.c
drivers/net/phy/marvell.c
drivers/net/vxlan.c
All three conflicts were cases of simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds documentation for the DT bindings of the charger
subdevice of ACT8945A MFD.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This resolves the merge issues and confusions people were having with
the goldfish drivers due to changes for them showing up in two different
trees.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull networking fixes from David Miller:
"Looks like a lot, but mostly driver fixes scattered all over as usual.
Of note:
1) Add conditional sched in nf conntrack in cleanup to avoid NMI
watchdogs. From Florian Westphal.
2) Fix deadlock in nfnetlink cttimeout, also from Floarian.
3) Fix handling of slaves in bonding ARP monitor validation, from Jay
Vosburgh.
4) Callers of ip_cmsg_send() are responsible for freeing IP options,
some were not doing so. Fix from Eric Dumazet.
5) Fix per-cpu bugs in mvneta driver, from Gregory CLEMENT.
6) Fix vlan handling in mv88e6xxx DSA driver, from Vivien Didelot.
7) bcm7xxx PHY driver bug fixes from Florian Fainelli.
8) Avoid unaligned accesses to protocol headers wrt. GRE, from
Alexander Duyck.
9) SKB leaks and other problems in arc_emac driver, from Alexander
Kochetkov.
10) tcp_v4_inbound_md5_hash() releases listener socket instead of
request socket on error path, oops. Fix from Eric Dumazet.
11) Missing socket release in pppoe_rcv_core() that seems to have
existed basically forever. From Guillaume Nault.
12) Missing slave_dev unregister in dsa_slave_create() error path,
from Florian Fainelli.
13) crypto_alloc_hash() never returns NULL, fix return value check in
__tcp_alloc_md5sig_pool. From Insu Yun.
14) Properly expire exception route entries in ipv4, from Xin Long.
15) Fix races in tcp/dccp listener socket dismantle, from Eric
Dumazet.
16) Don't set IFF_TX_SKB_SHARING in vxlan, geneve, or GRE, it's not
legal. These drivers modify the SKB on transmit. From Jiri Benc.
17) Fix regression in the initialziation of netdev->tx_queue_len.
From Phil Sutter.
18) Missing unlock in tipc_nl_add_bc_link() error path, from Insu Yun.
19) SCTP port hash sizing does not properly ensure that table is a
power of two in size. From Neil Horman.
20) Fix initializing of software copy of MAC address in fmvj18x_cs
driver, from Ken Kawasaki"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (129 commits)
bnx2x: Fix 84833 phy command handler
bnx2x: Fix led setting for 84858 phy.
bnx2x: Correct 84858 PHY fw version
bnx2x: Fix 84833 RX CRC
bnx2x: Fix link-forcing for KR2
net: ethernet: davicom: fix devicetree irq resource
fmvj18x_cs: fix incorrect indexing of dev->dev_addr[] when copying the MAC address
Driver: Vmxnet3: Update Rx ring 2 max size
net: netcp: rework the code for get/set sw_data in dma desc
soc: ti: knav_dma: rename pad in struct knav_dma_desc to sw_data
net: ti: netcp: restore get/set_pad_info() functionality
MAINTAINERS: Drop myself as xen netback maintainer
sctp: Fix port hash table size computation
can: ems_usb: Fix possible tx overflow
Bluetooth: hci_core: Avoid mixing up req_complete and req_complete_skb
net: bcmgenet: Fix internal PHY link state
af_unix: Don't use continue to re-execute unix_stream_read_generic loop
unix_diag: fix incorrect sign extension in unix_lookup_by_ino
bnxt_en: Failure to update PHY is not fatal condition.
bnxt_en: Remove unnecessary call to update PHY settings.
...
This is the DPCM based machine driver with rt5650
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Koro Chen <koro.chen@mediatek.com>
Signed-off-by: PC Liao <pc.liao@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
enable/disable master clock when codec is active or not.
Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add devicetree bindings for i2s controller found on rk3399
processors from rockchip.
It's helpful to add full set of compatible strings for serials
of Rockchip SoCs (rk3066, rk3188, rk3288, rk3399).
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
- mvebu:
- Add odmi driver for Marvell 7K/8K SoCs
- Replace driver-specific set_affinity with generic version
- mips:
- Move ath79 MISC and CPU drivers from arch/ code to irqchip/
- tango:
- Add support for Sigma Designs SMP8[67]xx ctrl
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=4dMI
-----END PGP SIGNATURE-----
Merge tag 'irqchip-core-4.6-2' of git://git.infradead.org/users/jcooper/linux into irq/core
Pull the second round of irqchip core changes for v4.6 from Jason Cooper:
- mvebu:
- Add odmi driver for Marvell 7K/8K SoCs
- Replace driver-specific set_affinity with generic version
- mips:
- Move ath79 MISC and CPU drivers from arch/ code to irqchip/
- tango:
- Add support for Sigma Designs SMP8[67]xx ctrl
fallout from adding Tegra210 and rockchip rk3036/rk3368 drivers
this cycle. There's also the random smattering of sparse/checker
fixes, a build "fix" to get the Tango clk driver to compile
because the Kconfig symbol was renamed after the fact, and a clk
gpio fix for a patch mismerge.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=I6OK
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk driver fixes from Stephen Boyd:
"An assortment of vendor specific clk drivers fixes, most notably
fallout from adding Tegra210 and rockchip rk3036/rk3368 drivers this
cycle.
There's also the random smattering of sparse/checker fixes, a build
"fix" to get the Tango clk driver to compile because the Kconfig
symbol was renamed after the fact, and a clk gpio fix for a patch
mismerge"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (28 commits)
clk: gpio: Really allow an optional clock= DT property
Revert "clk: qcom: Specify LE device endianness"
clk: versatile: mask VCO bits before writing
clk: tegra: super: Fix sparse warnings for functions not declared as static
clk: tegra: Fix sparse warnings for functions not declared as static
clk: tegra: Fix sparse warning for pll_m
clk: tegra: Use definition for pll_u override bit
clk: tegra: Fix warning caused by pll_u failing to lock
clk: tegra: Fix clock sources for Tegra210 EMC
clk: tegra: Add the APB2APE audio clock on Tegra210
clk: tegra: Add missing of_node_put()
clk: tegra: Fix PLLE SS coefficients
clk: tegra: Fix typos around clearing PLLE bits during enable
clk: tegra: Do not disable PLLE when under hardware control
clk: tegra: Fix pllx dyn step calculation
clk: tegra: pll: Fix potential sleeping-while-atomic
clk: tegra: Fix the misnaming of nvenc from msenc
clk: tegra: Fix naming of MISC registers
clk: tango4: rename ARCH_TANGOX to ARCH_TANGO
clk: scpi: Fix checking return value of platform_device_register_simple()
...
Add device tree bindings for the I/F/I CANFD controller IP core.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add vendor prefix for I/F/I, Ingenieurbüro Für IC-Technologie
http://www.ifi-pld.de/
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This commit adds documentation for the Technologic Systems version of
SJA1000. The difference with the NXP version is in the way the registers
are accessed.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
As requested by Rob Herring on patch
https://patchwork.ozlabs.org/patch/580862/.
This is a new property that it's still in net-next and has never been
used in production, so we are not breaking anything with the
incompatible binding change.
Signed-off-by: Sergio Prado <sergio.prado@e-labworks.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 8e6ebfaa9b.
Without the patch reverted regulators will not work. This prevents
MMC to be working for example so the boards can not boot to
MMC rootfs.
Tested it on beaglebone white and bisect also points to the
reverted commit.
The issue can be also fixed by adding "regulator-compatible =" to all board
dts file for the regulators.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add devicetree bindings for the SPDIF transceiver found on
found on Allwinners A10 and A20 SoCs.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Maxim Semiconductor's PMIC MAX77620/MAX20024 has multiple
DCDCs and LDOs.
Add DT binding document to support these regulators via
regulator framework.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This commits adds a new irqchip driver that handles the ODMI
controller found on Marvell 7K/8K processors. The ODMI controller
provide MSI interrupt functionality to on-board peripherals, much like
the GIC-v2m.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1455888883-5127-1-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Update description for X-Gene standby GPIO controller DTS binding to
support GPIO line configuration as input, output or external IRQ pin.
Signed-off-by: Y Vo <yvo@apm.com>
Signed-off-by: Quan Nguyen <qnguyen@apm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The IP version number carries enough information to identify the exact
device instance features. Drop the related DT properties and use the IP
version instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add DT compatible strings for the VSP2 instances found in the R-Car Gen3
SoCs and support them in the vsp1 driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Not all VSP1 instances include a UDS. Make the renesas,#uds DT property
optional and accept a number of UDS equal to 0 as valid.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add devicetree bindings for Rockchip rk3399 spi which found on
Rockchip rk3399 SoCs.
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds a binding for the secondary interrupt controller in
Sigma Designs SMP86xx and SMP87xx chips.
Signed-off-by: Mans Rullgard <mans@mansr.com>
[ jac: use 'interrupt-controller@XXX' notation in binding doc ]
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lkml.kernel.org/r/1453313237-18570-1-git-send-email-mans@mansr.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The example in the DT binding documentation uses the preliminary DT
bindings for the r8a7795 MSTP clocks, which never went upstream.
Update the example to use the DT bindings for the upstream Clock Pulse
Generator / Module Standby and Software Reset hardware block.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
wl12xx
* add device tree support for SPI
mwifiex
* add debugfs file to read chip information
* add MSIx support for newer pcie chipsets (8997 onwards)
* add schedule scan support
* add WoWLAN net-detect support
* firmware dump support for w8997 chipset
iwlwifi
* continue the work on multiple Rx queues
* add support for beacon storing used in low power states
* use the regular firmware image of WoWLAN
* fix 8000 devices for Big Endian machines
* more firmware debug hooks
* add support for P2P Client snoozing
* make the beacon filtering for AP mode configurable
* fix transmit queues overflow with LSO
libertas
* add support for setting power save via cfg80211
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJWvbW+AAoJEG4XJFUm622b1lIH/RmFoJNbJka9/CrDse5ndb3A
TBRDGvinOjubHn9Hn8Baz7u0huXvBpWoN/YI4hqjKTW4YsXfN8cB1IJakzohLFCF
I9kUhITYGrK7hKDwkBsop2qxwJsrkAzv/XNzi+yGqxlj/IqZp+pYBmZTb9H6G963
lb8hJPhx+t2aCBPvDdkAd5n67kdq0C35At+a1KB1CYFYKdYO5y5QeDLYtb+5zrWT
/Pwel7gRdgcf4TpaUZs++mDf+agcFo+JjG+olLrZNw1BDthA8VC46agMyfffrt4l
dRZIS07fUDd0zf4HJMWV05l8kKdEwqrRAuoBOnxGI611GNN94M3NWJDxU/MgBos=
=zE9m
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2016-02-12' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
Major changes:
wl12xx
* add device tree support for SPI
mwifiex
* add debugfs file to read chip information
* add MSIx support for newer pcie chipsets (8997 onwards)
* add schedule scan support
* add WoWLAN net-detect support
* firmware dump support for w8997 chipset
iwlwifi
* continue the work on multiple Rx queues
* add support for beacon storing used in low power states
* use the regular firmware image of WoWLAN
* fix 8000 devices for Big Endian machines
* more firmware debug hooks
* add support for P2P Client snoozing
* make the beacon filtering for AP mode configurable
* fix transmit queues overflow with LSO
libertas
* add support for setting power save via cfg80211
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We need that for a custom hardware that needs the reverse reset
sequence.
Signed-off-by: Bernhard Walle <bernhard@bwalle.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Document the devicetree bindings for the random number generator found
on Microchip PIC32 class devices.
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds the device tree binding documentation for
hi655x PMIC regulator.
Signed-off-by: Chen Feng <puck.chen@hisilicon.com>
Signed-off-by: Fei Wang <w.f@huawei.com>
Signed-off-by: Xinwei Kong <kong.kongxinwei@hisilicon.com>
Reviewed-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Implement an 'external-control' option for when the charger
shouldn't be configured by the kernel.
Signed-off-by: Jonathan Tinkham <sctincman@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
New Device Support
* Apex stx104 DAC
- new driver for this PC104 board. Right now DAC support only.
* ADI ad5064
- Add support for ad5625, ad5627, ad5645, ad5665, ad5667 DACs.
- Add support for Linear Technology ltc2606, ltc2607, ltc2609, ltc2616,
ltc2617, ltc2619, ltc2626, ltc2627 and ltc2629.
* ADI ad7192
- add support for the ad7193
* Invensense mpu6050
- substantial rework of driver to use regmap allowing SPI support extending
the now split driver to cover the MPU6000.
* TI adc0832
- new driver supporting ADC0831, ADC0832, ADC0834 and ADC0838 ADCs.
* TI ads1015
- new driver, note that there is an existing hwmon driver. The long term
intention is to probably remove the hwmon driver but for now we just have
guards in place to ensure this driver is not built if that one is enabled.
* TI afe4403
- new driver for this heart rate monitor / pulse oximeter front end chip.
* TI afe4404
- new driver for this heart rate monitor / pulse oximeter front end chip.
Staging Graduations
* mxs-lradc
- A combined general purpose and touch screen (input) device driver.
Originally held in staging to allow reworking into and MFD but as
that wasn't happening and isn't an absolute requirement we are moving
it out of staging.
Driver new features
* ms5611
- triggered buffer support
- IIO_CHAN_INFO_SCALE to aid the triggered buffer support.
Driver cleanups / reworks / fixes
* ad5064
- Use an enum for the register map layout to allow support of additional
chips (precursor to the new support listed above).
- Structural driver changes to allow support of the slightly different
handling for the ltc parts above.
* ad5933
- drop an exceptional & unnecessary for a function pointer.
* ad7606
- Cleanup the repeated copies of pm ops.
- consolidate the various channels specs via a sport of rearranging so only
one version is needed.
* atlas ph sensor
- add select IRQ_WORK
* hmc8543 (soon to move out of staging)
- Comment style fixes
- functionality of suspend and resume was swapped.
* spear-adc
- use devm_clk_dev instead of managing the clk lifetime by hand.
Core
* Use new dmaengine_terminate_sync call to avoid a theoretical race.
* Fix docs for mlock in struct iio_dev as it is correctly taken in some
drivers (docs used to say for core only).
* Add a helper function for calculating the scan index storage size within
the core cutting out some cut and paste versions of the same code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=LIQe
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.6b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
2nd round of new IIO device support, features and cleanups for the 4.6 cycle.
New Device Support
* Apex stx104 DAC
- new driver for this PC104 board. Right now DAC support only.
* ADI ad5064
- Add support for ad5625, ad5627, ad5645, ad5665, ad5667 DACs.
- Add support for Linear Technology ltc2606, ltc2607, ltc2609, ltc2616,
ltc2617, ltc2619, ltc2626, ltc2627 and ltc2629.
* ADI ad7192
- add support for the ad7193
* Invensense mpu6050
- substantial rework of driver to use regmap allowing SPI support extending
the now split driver to cover the MPU6000.
* TI adc0832
- new driver supporting ADC0831, ADC0832, ADC0834 and ADC0838 ADCs.
* TI ads1015
- new driver, note that there is an existing hwmon driver. The long term
intention is to probably remove the hwmon driver but for now we just have
guards in place to ensure this driver is not built if that one is enabled.
* TI afe4403
- new driver for this heart rate monitor / pulse oximeter front end chip.
* TI afe4404
- new driver for this heart rate monitor / pulse oximeter front end chip.
Staging Graduations
* mxs-lradc
- A combined general purpose and touch screen (input) device driver.
Originally held in staging to allow reworking into and MFD but as
that wasn't happening and isn't an absolute requirement we are moving
it out of staging.
Driver new features
* ms5611
- triggered buffer support
- IIO_CHAN_INFO_SCALE to aid the triggered buffer support.
Driver cleanups / reworks / fixes
* ad5064
- Use an enum for the register map layout to allow support of additional
chips (precursor to the new support listed above).
- Structural driver changes to allow support of the slightly different
handling for the ltc parts above.
* ad5933
- drop an exceptional & unnecessary for a function pointer.
* ad7606
- Cleanup the repeated copies of pm ops.
- consolidate the various channels specs via a sport of rearranging so only
one version is needed.
* atlas ph sensor
- add select IRQ_WORK
* hmc8543 (soon to move out of staging)
- Comment style fixes
- functionality of suspend and resume was swapped.
* spear-adc
- use devm_clk_dev instead of managing the clk lifetime by hand.
Core
* Use new dmaengine_terminate_sync call to avoid a theoretical race.
* Fix docs for mlock in struct iio_dev as it is correctly taken in some
drivers (docs used to say for core only).
* Add a helper function for calculating the scan index storage size within
the core cutting out some cut and paste versions of the same code.
Pull thermal management fixes from Eduardo Valentin:
"Specifics in this pull request:
- Compilation fixes on SPEAR, and U8500 thermal drivers.
- RCAR thermal driver now recognizes OF-thermal based thermal zones.
- Small code rework on OF-thermal.
- These change have been CI tested using KernelCI bot [1,2]. \o/
I am taking over on Rui's behalf while he is out. Happy New Chinese
Year!
[1] - https://kernelci.org/build/evalenti/kernel/v4.5-rc3-16-ga53b8394ec3c/
[2] - https://kernelci.org/boot/all/job/evalenti/kernel/v4.5-rc3-16-ga53b8394ec3c/"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
thermal: cpu_cooling: fix out of bounds access in time_in_idle
thermal: allow u8500-thermal driver to be a module
thermal: allow spear-thermal driver to be a module
thermal: spear: use __maybe_unused for PM functions
thermal: rcar: enable to use thermal-zone on DT
thermal: of: use for_each_available_child_of_node for child iterator
AER
Flush workqueue on device remove to avoid use-after-free (Sebastian Andrzej Siewior)
Broadcom iProc host bridge driver
Allow multiple devices except on PAXC (Ray Jui)
Renesas R-Car host bridge driver
Add gen2 device tree support for r8a7793 (Simon Horman)
Add device tree support for r8a7793 (Simon Horman)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=6Txq
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.5-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"These are some Renesas binding updates for PCI host controllers, a
Broadcom fix for a regression we added in v4.5-rc1, and a fix for an
AER use-after-free problem that can cause memory corruption.
Summary:
AER:
Flush workqueue on device remove to avoid use-after-free (Sebastian Andrzej Siewior)
Broadcom iProc host bridge driver:
Allow multiple devices except on PAXC (Ray Jui)
Renesas R-Car host bridge driver:
Add gen2 device tree support for r8a7793 (Simon Horman)
Add device tree support for r8a7793 (Simon Horman)"
* tag 'pci-v4.5-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: rcar: Add device tree support for r8a7793
PCI: rcar: Add gen2 device tree support for r8a7793
PCI: iproc: Allow multiple devices except on PAXC
PCI/AER: Flush workqueue on device remove to avoid use-after-free
The S3C Real Time Clock driver requires the clock and source clock to
be defined in the device node but that requirement is not documented.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The arm,gic-v3 binding was written with good intentions and doesn't
enforce interrupt-cells to be 3, therefore making it easy to extend
the irq description in future if necessary:
> Cells 4 and beyond are reserved for future use.
Unfortunately, this sentence is immediately followed up with:
> When the 1st cell has a value of 0 or 1, cells 4 and beyond act as
> padding, and may be ignored. It is recommended that padding cells
> have a value of 0.
Consequently, any extensions to the PPI or SPI interrupt specifiers must
be able to work with random crap from legacy DTs, effectively
necessitating a new interrupt type in the first cell. Sigh.
This patch fixes the text so that additional, reserved cells are
required to be zero. This looks like a reasonable thing to require and
is already satisifed by the .dts files in-tree.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Add vendor prefix for United Radiant Technology Corporation,
a provider of liquid crystal display technologies.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Rob Herring <robh@kernel.org>
A common review comment is to add units to DT property names. The naming
convention is inconsistent unfortunately although there are clear
majorities in use already. This makes it hard to remember the exact name
preferred, so I'm documenting this to provide an easy point of
reference.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
The AXP223 is a new PMIC commonly paired with Allwinner A23/A33 SoCs.
It is functionally identical to AXP221; only the regulator default
voltage/status and the external host interface are different.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The TPS65912 PMIC contains several regulators and a GPIO controller.
Add bindings for the TPS65912 PMIC.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This is the touchscreen conversion queue binding documentation. It uses
the shared imx25 ADC.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The documentation describes the bindings for the imx25 GCQ unit which is
essentially a generic conversion queue using the imx25 ADC.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This documentation describes the devicetree bindings for the
ADC/Touchscreen unit of the i.MX25 SoC.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The OCTEON SATA controller is currently found on cn71XX devices.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Vinita Gupta <vgupta@caviumnetworks.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@auriga.com>
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Tested on Acqua A5 SoM (http://www.acmesystems.it/acqua).
Signed-off-by: Sergio Prado <sergio.prado@e-labworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tvp5150 decoder has different input connectors so extend the device
tree binding to allow device tree source files to define the connectors
that are available on a given board.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The pinctrl of rk3399 is much different from other's,
especially the 3bits of drive strength.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove fw_cfg hardware interface details from
Documentation/devicetree/bindings/arm/fw-cfg.txt,
and replace them with a pointer to the authoritative
documentation in the QEMU source tree.
Signed-off-by: Gabriel Somlo <somlo@cmu.edu>
Cc: Laszlo Ersek <lersek@redhat.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit documents bindings to be added to the eeprom_93xx46 driver
which will allow:
- Device word size and read-only attributes to be specified.
- A device-specific compatible string for use with Atmel AT93C46D
EEPROMs.
- Specifying a GPIO line to function as a 'select' or 'enable' signal
prior to accessing the EEPROM.
Signed-off-by: Cory Tusar <cory.tusar@pid1solutions.com>
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Chris Healy <chris.healy@zii.aero>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds ADC0831/ADC0832/ADC0834/ADC0838 8-bit ADC driver.
I have tested with ADC0831 and ADC0832. The remaining ADC0834 and
ADC0838 are very similar to ADC0832.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch enables to use thermal-zone on DT if it was calles as
"renesas,rcar-thermal-gen2".
Previous style (= non thermal-zone) is still supported by
"renesas,rcar-thermal" to keep compatibility for "git bisect".
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWt9V+AAoJEHm+PkMAQRiGvqUH/iKVFxRB+MpfwRteRv22gfxJ
8Y5jDuCt2qkePHieN5JoY4FqWIA+hR+UnctHBvOCLC7DNbY79yaYuWeuShfnRVw2
91Kspk2tgnWkjlZDZ273VNKAEveFYUdhHvHFUlItWubVIlzrKRGKdAcUpecQ33YD
IERr4VFxdQDgksGPzH2FLJwcAKilWWygQ9ATTsY0xJepTC6PwxAFxrNx5qPiqOoI
aHJBzczk50y9hHEPkYeeWloyzIZUmf81BCi/VwOsbB30q4ENwkS2MMnebhOmBjLp
g9Bml8m/Fk4N+h2vbcLj6Bu+rE+bYDZDZ2Fmbupy4NbEkng3x3iaTPkG+R2hErQ=
=IdcS
-----END PGP SIGNATURE-----
Merge tag 'v4.5-rc3' into patchwork
Linux 4.5-rc3
* tag 'v4.5-rc3': (644 commits)
Linux 4.5-rc3
epoll: restrict EPOLLEXCLUSIVE to POLLIN and POLLOUT
radix-tree: fix oops after radix_tree_iter_retry
MAINTAINERS: trim the file triggers for ABI/API
dax: dirty inode only if required
thp: make deferred_split_scan() work again
mm: replace vma_lock_anon_vma with anon_vma_lock_read/write
ocfs2/dlm: clear refmap bit of recovery lock while doing local recovery cleanup
um: asm/page.h: remove the pte_high member from struct pte_t
mm, hugetlb: don't require CMA for runtime gigantic pages
mm/hugetlb: fix gigantic page initialization/allocation
mm: downgrade VM_BUG in isolate_lru_page() to warning
mempolicy: do not try to queue pages from !vma_migratable()
mm, vmstat: fix wrong WQ sleep when memory reclaim doesn't make any progress
vmstat: make vmstat_update deferrable
mm, vmstat: make quiet_vmstat lighter
mm/Kconfig: correct description of DEFERRED_STRUCT_PAGE_INIT
memblock: don't mark memblock_phys_mem_size() as __init
dump_stack: avoid potential deadlocks
mm: validate_mm browse_rb SMP race condition
...
This patch adds the "arm, pl330-broken-no-flushp" for arm-pl330.
Reviewed-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Sonny Rao <sonnyrao@chromium.org>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add binding documentation for the bcm2835-aux-uart driver.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simply document new compat strings.
There appears to be no need for a driver updates.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the TI AFE4403 heart monitor DT bindings documentation.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add the TI afe4404 heart monitor DT bindings documentation.
Create health directory created under iio.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Document the devicetree bindings for PINCTRL and GPIO found on Microchip
PIC32 class devices.
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Rob Herring <robh@kernel.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add "renesas,pcie-r8a7793" as a compatibility string for
"renesas,pcie-rcar-gen2".
This doesn't change the driver, so it does nothing by itself. But it
does mean that checkpatch won't complain about a future patch that adds
"renesas,pci-r8a7793" to a DT, which helps ensure that shipped DTs use
documented compatibility strings.
[bhelgaas: changelog]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rob Herring <robh@kernel.org>
Add "renesas,pci-r8a7793" as a compatibility string for
"renesas,pci-rcar-gen2".
This doesn't change the driver, so it does nothing by itself. But it
does mean that checkpatch won't complain about a future patch that adds
"renesas,pci-r8a7793" to a DT, which helps ensure that shipped DTs use
documented compatibility strings.
[bhelgaas: changelog]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rob Herring <robh@kernel.org>
LP872x regulators are made active via the EN pin, which might be hooked to a
GPIO. This adds support for driving the GPIO high when the driver is in use.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds documentation for the DT bindings of the regulator
subdevice of ACT8945A MFD.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the devicetree bindings documentation for the Analog Devices
axi-spi-engine SPI master peripheral. This is a soft-peripheral used in
FPGAs.
The external interfaces of the peripheral are:
* A memory mapped register map which is used to configure the
peripheral.
* One interrupt.
* Two clocks, one for the memory mapped register interface and one
for the SPI bus.
* A SPI master interface to which the slave devices are connected.
These interfaces are described by the devicetree bindings accordingly.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
add cs4271 and cs42727 support for fsl-asoc-card
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DT binding doc references the max77802 clocks header file which makes
no sense since of course it doesn't contain data related to the regulators.
It's a copy and paste error, so add a reference to the correct header file.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is the initial codec driver for rt5514. The codec includes a low power
DSP for voice wake up. The register address is incremental by 4 in the DSP
memory map. In order to recover the codec settings in the codec mode and
manipulate the DSP mode for voice wake up, we use the multi-level register
map. One is for ALSA API in codec mode that can be recovered by cache
before recording. Another is for DSP related settings that can be accessed
with 32bit address of the DSP in the application of voice wake up.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull networking fixes from David Miller:
"This looks like a lot but it's a mixture of regression fixes as well
as fixes for longer standing issues.
1) Fix on-channel cancellation in mac80211, from Johannes Berg.
2) Handle CHECKSUM_COMPLETE properly in xt_TCPMSS netfilter xtables
module, from Eric Dumazet.
3) Avoid infinite loop in UDP SO_REUSEPORT logic, also from Eric
Dumazet.
4) Avoid a NULL deref if we try to set SO_REUSEPORT after a socket is
bound, from Craig Gallek.
5) GRO key comparisons don't take lightweight tunnels into account,
from Jesse Gross.
6) Fix struct pid leak via SCM credentials in AF_UNIX, from Eric
Dumazet.
7) We need to set the rtnl_link_ops of ipv6 SIT tunnels before we
register them, otherwise the NEWLINK netlink message is missing
the proper attributes. From Thadeu Lima de Souza Cascardo.
8) Several Spectrum chip bug fixes for mlxsw switch driver, from Ido
Schimmel
9) Handle fragments properly in ipv4 easly socket demux, from Eric
Dumazet.
10) Don't ignore the ifindex key specifier on ipv6 output route
lookups, from Paolo Abeni"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (128 commits)
tcp: avoid cwnd undo after receiving ECN
irda: fix a potential use-after-free in ircomm_param_request
net: tg3: avoid uninitialized variable warning
net: nb8800: avoid uninitialized variable warning
net: vxge: avoid unused function warnings
net: bgmac: clarify CONFIG_BCMA dependency
net: hp100: remove unnecessary #ifdefs
net: davinci_cpdma: use dma_addr_t for DMA address
ipv6/udp: use sticky pktinfo egress ifindex on connect()
ipv6: enforce flowi6_oif usage in ip6_dst_lookup_tail()
netlink: not trim skb for mmaped socket when dump
vxlan: fix a out of bounds access in __vxlan_find_mac
net: dsa: mv88e6xxx: fix port VLAN maps
fib_trie: Fix shift by 32 in fib_table_lookup
net: moxart: use correct accessors for DMA memory
ipv4: ipconfig: avoid unused ic_proto_used symbol
bnxt_en: Fix crash in bnxt_free_tx_skbs() during tx timeout.
bnxt_en: Exclude rx_drop_pkts hw counter from the stack's rx_dropped counter.
bnxt_en: Ring free response from close path should use completion ring
net_sched: drr: check for NULL pointer in drr_dequeue
...
Device Support
* ad5761
- new driver
* at91_sama5d2 ADC.
- new driver and MAINTAINERS entry.
- minor cleanups followed.
* atlas pH-SM
- new driver (this has possibly the prettiest data sheet I've ever seen)
* mcp3422
- mcp3425 ADC added.
* mcp4725
- mcp4726 DAC added.
* mma8452
- mma8451q accelerometer added.
* mpl115
- mpl115a1 added (a lot bigger than it seems as this is an SPI part whereas
previous parts were i2c).
* si7005
- Hoperf th02 (seems to be a repackaged part)
* si7020
- Hoperf th06 (seems to be a repackaged part)
New features
* Core
- IIO_PH type. Does what it says on the tin.
* max30100
- LED current configuration support.
* mcp320x
- more differential measurement combinations.
* mma8452
- free fall deteciton
- opt3001
- enable operation without a IRQ line.
- device tree docs. Somehow the original docs have disappeared down
a rabbit hole, so here is a new set.
* st-sensors
- Support active-low interrupts.
Cleanups and minor / not so minor reworks
* Documentation
- drop some defunct ABI from the docs in staging.
* presure / Kconfig
- white space cleanup.
* ad7150
- BIT macro usage
- Alignment fixes
* ad7192
- false indent fixed.
* ak8975
- constify the ak_def structures
* axp288
- drop a redundant double const.
* dht11
- substantial reliability improvements by being more tolerant
of missing start bits.
- simplify the decoding algorithm
* mma8452
- whitespace cleanup
* mpl115
- don't bother setting i2c_client_data as nothing uses it.
* mpu6050
- drop unused function parameter.
* opt3001
- extract integration time as constants.
- trivial refactoring.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=fgTH
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.6a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First round of new IIO device support, features and cleanups for the 4.6 cycle.
Device Support
* ad5761
- new driver
* at91_sama5d2 ADC.
- new driver and MAINTAINERS entry.
- minor cleanups followed.
* atlas pH-SM
- new driver (this has possibly the prettiest data sheet I've ever seen)
* mcp3422
- mcp3425 ADC added.
* mcp4725
- mcp4726 DAC added.
* mma8452
- mma8451q accelerometer added.
* mpl115
- mpl115a1 added (a lot bigger than it seems as this is an SPI part whereas
previous parts were i2c).
* si7005
- Hoperf th02 (seems to be a repackaged part)
* si7020
- Hoperf th06 (seems to be a repackaged part)
New features
* Core
- IIO_PH type. Does what it says on the tin.
* max30100
- LED current configuration support.
* mcp320x
- more differential measurement combinations.
* mma8452
- free fall deteciton
- opt3001
- enable operation without a IRQ line.
- device tree docs. Somehow the original docs have disappeared down
a rabbit hole, so here is a new set.
* st-sensors
- Support active-low interrupts.
Cleanups and minor / not so minor reworks
* Documentation
- drop some defunct ABI from the docs in staging.
* presure / Kconfig
- white space cleanup.
* ad7150
- BIT macro usage
- Alignment fixes
* ad7192
- false indent fixed.
* ak8975
- constify the ak_def structures
* axp288
- drop a redundant double const.
* dht11
- substantial reliability improvements by being more tolerant
of missing start bits.
- simplify the decoding algorithm
* mma8452
- whitespace cleanup
* mpl115
- don't bother setting i2c_client_data as nothing uses it.
* mpu6050
- drop unused function parameter.
* opt3001
- extract integration time as constants.
- trivial refactoring.
The original documentation as submitted with the driver appears to have
dropped down a rabbit hole.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add fallback compatibility string.
This is in keeping with the fallback scheme being adopted wherever
appropriate for drivers for Renesas SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Device Tree bindings for the Camera Adaptation Layer (CAL) driver
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for the Atlas Scientific pH-SM chemical sensor that can
detect pH levels of solutions in the range of 0-14.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add the "atlas" vendor prefix for Atlas Scientific LLC
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Also rename the external input for the emac on rk3036, which
should still be ok to do, as that binding was only introduced
during this merge-window.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJWm9wLAAoJEPOmecmc0R2BfbUIAI7VaIzwhl4NkAO3x0P6emZT
B/2C4RuPLW9oBf/YGxG+HsxD2iLpDjAlZADlGBXsrdkfjFuN0iULc8COrFJEGv0F
HuFmxJz7IZCNS4BgXt+vk0yb43c1lLSMRSmTyWaY7izYUlQtcmDp/t7zTvwun9NM
N2U44zXFsEnTtsb3gV65PivrMBT/sNK9MyOIylh3Xjs/v+fTCtsHwPVckFwiIiPx
ER9ETDmeo/DEMtsutHTlCcujyvZXE3jsho0Ow7J/vuRJSbXkCW+Ki9CQZEvHGWXL
7ZaST8A8LEBjvslCh9IkirZ7qi20wwk/md3zAeoE0+eimEOEIqWYF8qwsWHiJjU=
=oT+p
-----END PGP SIGNATURE-----
Merge tag 'v4.5-rockchip-clkfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into clk-fixes
Pull rockchip fixes from Heiko Stuebner:
Fixes for wrong register offsets in both rk3036 and rk3368.
Also rename the external input for the emac on rk3036, which
should still be ok to do, as that binding was only introduced
during this merge-window.
* tag 'v4.5-rockchip-clkfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
clk: rockchip: rk3368: fix some clock gates
clk: rockchip: rk3036: rename emac ext source clock
clk: rockchip: rk3036: fix the div offset for emac clock
clk: rockchip: rk3036: fix uarts clock error
clk: rockchip: rk3036: fix the FLAGs for clock mux
The DT binding doc references the max77802 clocks header file which makes
no sense since of course it doesn't contain data related to the regulators.
It's a copy and paste error, so add a reference to the correct header file.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add DT support for the wl1271 SPI WiFi.
Add documentation file for the wl1271 SPI WiFi.
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Rob Herring <robh@kernel.org>
Tested-By: Sebastian Reichel <sre@kernel.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add bindings so we don't need to rely on goldfish virtual bus for
probing any more, which means we don't need ARM and MIPS goldfish
board code for instantiating the bus.
In the long term we would like to move towards replacing the Android
pipe with virtio-vsock that is currently under development.
Signed-off-by: Greg Hackmann <ghackmann@google.com>
Signed-off-by: Jin Qian <jinqian@android.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PHY devices may only list compatibility with clause 22, 45, and if
they need to be more specific, their PHY identifier values. No other
compatible strings are allowed. Make this clear in the documentation,
and remove examples where make/model compatible strings are listed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
