The check for xc5000 assumes that the tuner will always
be using the same bus and will have the same address.
As those are configurable via dev->board, it should use,
instead, the values defined there.
Also, a similar type of test will be needed by other
tuners (for example, for TUNER_XC2028)
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This was supposed to be an unlock on the error path.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Cc: Palash Bandyopadhyay < palash.bandyopadhyay@conexant.com>
Cc: Sri Deevi <Srinivasa.Deevi@conexant.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Nobody is ever going to implement an i2c based IR controller on a bridge that
has an onboard universal IR receiver. This stuff was all copied from em28xx,
which has old enough versions of the chip that some didn't have onboard IR.
Remove the stubs related to i2c based IR (keeping the cx231xx-input code).
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is no point in defining I2C adapter IDs when no code is using
them. As this field might go away in the future, stop using it when
we don't need to.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For specific boards, pass initialization data to ir-kbd-i2c instead
of modifying the settings after the device is initialized. This is
more efficient and easier to read.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Let card drivers probe for IR receiver devices and instantiate them if
found. Ultimately it would be better if we could stop probing
completely, but I suspect this won't be possible for all card types.
There's certainly room for cleanups. For example, some drivers are
sharing I2C adapter IDs, so they also had to share the list of I2C
addresses being probed for an IR receiver. Now that each driver
explicitly says which addresses should be probed, maybe some addresses
can be dropped from some drivers.
Also, the special cases in saa7134-i2c should probably be handled on a
per-board basis. This would be more efficient and less risky than always
probing extra addresses on all boards. I'll give it a try later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove some printk's that were needed only during development phase. Also,
cleans the printed messages to produce a nicer result.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch converts cx231xx to the new v4l2 dev/subdev, doing:
- Conversion of i2c calls to subdev calls;
- all subdev calls to call_all();
- Corrected the header file order in cx231xx.h;
- Added tuner frequency setting.
Signed-off-by: Srinivasa Deevi <srinivasa.deevi@conexant.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
changed the pcb-config.c/h to pcb-cfg.c/h for short names.
Signed-off-by: Srinivasa Deevi <srinivasa.deevi@conexant.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
