The ti_sn_aux_transfer() function returns ssize_t (signed long). It's
supposed to return negative error codes or the number of bytes
transferred. The "ret" variable is int and the "len" variable is
unsigned int.
The problem is that with a ternary like this, the negative int is first
type promoted to unsigned int to match "len" at this point it is a high
positive value. Then when it is type promoted to ssize_t (s64) it
remains a high positive value instead of sign extending and becoming a
negative again.
Fix this by removing the ternary.
Fixes: b137406d96 ("drm/bridge: ti-sn65dsi86: If refclk, DP AUX can happen w/out pre-enable")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/YKOGogHasIyvF8nj@mwanda
Let's reorganize how we init and turn on the reference clock in the
code to allow us to turn it on early (even before pre_enable()) so
that we can read the EDID early. This is handy for eDP because:
- We always assume that a panel is there.
- Once we report that a panel is there we get asked to read the EDID.
- Pre-enable isn't called until we know what pixel clock we want to
use and we're ready to turn everything on. That's _after_ we get
asked to read the EDID.
NOTE: the above only works out OK if we "refclk" is provided. Though I
don't have access to any hardware that uses ti-sn65dsi86 and _doesn't_
provide a "refclk", I believe that we'll have trouble reading the EDID
at bootup in that case. Specifically I believe that if there's no
"refclk" we need the MIPI source clock to be active before we can
successfully read the EDID. My evidence here is that, in testing, I
couldn't read the EDID until I turned on the DPPLL in the bridge chip
and that the DPPLL needs the input clock to be active.
Since this is hard to support, let's punt trying to handle this case
if there's no "refclk". In that case we'll enable comms in
pre_enable() like we always did.
I don't believe there are any users of the ti-sn65dsi86 bridge chip
that _don't_ use "refclk". The bridge chip is _very_ inflexible in
that mode. The only time I've seen that mode used was for some really
early prototype hardware that was thrown in the e-waste bin years ago
when we realized how inflexible it was.
Even if someone is using the bridge chip without the "refclk" they're
in no worse shape than they were before the (fairly recent) commit
58074b08c0 ("drm/bridge: ti-sn65dsi86: Read EDID blob over DDC").
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210423095743.v5.13.Ie8cf556114953c6e7634564cc0d3ddbd103cb96c@changeid
Let's use the newly minted aux bus to break up the driver into sub
drivers. We're not doing a full breakup here: all the code is still in
the same file and remains largely untouched. The big goal here of
using sub-drivers is to allow part of our code to finish probing even
if some other code needs to defer. This can solve some chicken-and-egg
problems. Specifically:
- In commit 48834e6084 ("drm/panel-simple: Support hpd-gpios for
delaying prepare()") we had to add a bit of a hack to simpel-panel
to support HPD showing up late. We can get rid of that hack now
since the GPIO part of our driver can finish probing early.
- We have a desire to expose our DDC bus to simple-panel (and perhaps
to a backlight driver?). That will end up with the same
chicken-and-egg problem. A future patch to move this to a sub-driver
will fix it.
- If/when we support the PWM functionality present in the bridge chip
for a backlight we'll end up with another chicken-and-egg
problem. If we allow the PWM to be a sub-driver too then it solves
this problem.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210423095743.v5.9.I3e68fa38c4ccbdbdf145cad2b01e83a1e5eac302@changeid
This is something that we've wanted for a while now: the ability to
actually look up the respective drm_device for a given drm_dp_aux struct.
This will also allow us to transition over to using the drm_dbg_*() helpers
for debug message printing, as we'll finally have a drm_device to reference
for doing so.
Note that there is one limitation with this - because some DP AUX adapters
exist as platform devices which are initialized independently of their
respective DRM devices, one cannot rely on drm_dp_aux->drm_dev to always be
non-NULL until drm_dp_aux_register() has been called. We make sure to point
this out in the documentation for struct drm_dp_aux.
v3:
* Add WARN_ON_ONCE() to drm_dp_aux_register() if drm_dev isn't filled out
Signed-off-by: Lyude Paul <lyude@redhat.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210423184309.207645-4-lyude@redhat.com
Reviewed-by: Dave Airlie <airlied@redhat.com>
We should be setting the drm_dp_aux_msg::reply field if a NACK or a
SHORT reply happens. Update the error bit handling logic in
ti_sn_aux_transfer() to handle these cases and notify upper layers that
such errors have happened. This helps the retry logic understand that a
timeout has happened, or to shorten the read length if the panel isn't
able to handle the longest read possible.
Note: I don't have any hardware that exhibits these code paths so this
is written based on reading the datasheet for this bridge and inspecting
the code and how this is called.
Changes in v2:
- Move WRITE_STATUS_UPDATE check from case to assignment
Changes in v2:
- Handle WRITE_STATUS_UPDATE properly
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Cc: Sean Paul <seanpaul@chromium.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20201102181144.3469197-5-swboyd@chromium.org
On some panels hooked up to the ti-sn65dsi86 bridge chip we found that
link training was failing. Specifically, we'd see:
ti_sn65dsi86 2-002d: [drm:ti_sn_bridge_enable] *ERROR* Link training failed, link is off (-5)
The panel was hooked up to a logic analyzer and it was found that, as
part of link training, the bridge chip was writing a 0x1 to DPCD
address 00600h and the panel responded NACK. As can be seen in header
files, the write of 0x1 to DPCD address 0x600h means we were trying to
write the value DP_SET_POWER_D0 to the register DP_SET_POWER. The
panel vendor says that a NACK in this case is not unexpected and means
"not ready, try again".
In testing, we found that this panel would respond with a NACK in
about 1/25 times. Adding the retry logic worked fine and the most
number of tries needed was 3. Just to be safe, we'll add 10 tries
here and we'll add a little blurb to the logs if we ever need more
than 5.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-By: Steev Klimaszewski <steev@kali.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20201002135920.1.I2adbc90b2db127763e2444bd5a4e5bf30e1db8e5@changeid
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200708121604.14292-1-grandmaster@al2klimov.de
ti-sn65dsi86 bridge is enumerated as a runtime device. When
suspend is triggered, PM core adds a refcount on all the
devices and calls device suspend, since usage count is
already incremented, runtime suspend will not be called
and it kept the bridge regulators and gpios ON which resulted
in platform not entering into XO shutdown.
Add changes to force suspend on the runtime device during pm sleep.
Signed-off-by: Harigovindan P <harigovi@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200609120455.20458-1-harigovi@codeaurora.org
The kernel test robot noted that if "OF" is defined (which is needed
to select DRM_TI_SN65DSI86 at all) but not OF_GPIO that we'd get
compile failures because some of the members that we access in "struct
gpio_chip" are only defined "#if defined(CONFIG_OF_GPIO)".
All the GPIO bits in the driver are all nicely separated out. We'll
guard them with the same "#if defined" that the header has and add a
little stub function if OF_GPIO is not defined.
Fixes: 27ed2b3f22 ("drm/bridge: ti-sn65dsi86: Export bridge GPIOs to Linux")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200612123003.v2.1.Ibe95d8f3daef01e5c57d4c8c398f04d6a839492c@changeid
The ti-sn65dsi86 MIPI DSI to eDP bridge chip supports arbitrary
remapping of eDP lanes and also polarity inversion. Both of these
features have been described in the device tree bindings for the
device since the beginning but were never implemented in the driver.
Implement both of them.
Part of this change also allows you to (via the same device tree
bindings) specify to use fewer than the max number of DP lanes that
the panel reports. This could be useful if your display supports more
lanes but only a few are hooked up on your board.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200518114656.REPOST.v2.1.Ibc8eeddcee94984a608d6900b46f9ffde4045da4@changeid
The ti-sn65dsi86 MIPI DSI to eDP bridge chip has 4 pins on it that can
be used as GPIOs in a system. Each pin can be configured as input,
output, or a special function for the bridge chip. These are:
- GPIO1: SUSPEND Input
- GPIO2: DSIA VSYNC
- GPIO3: DSIA HSYNC or VSYNC
- GPIO4: PWM
Let's expose these pins as GPIOs. A few notes:
- Access to ti-sn65dsi86 is via i2c so we set "can_sleep".
- These pins can't be configured for IRQ.
- There are no programmable pulls or other fancy features.
- Keeping the bridge chip powered might be expensive. The driver is
setup such that if all used GPIOs are only inputs we'll power the
bridge chip on just long enough to read the GPIO and then power it
off again. Setting a GPIO as output will keep the bridge powered.
- If someone releases a GPIO we'll implicitly switch it to an input so
we no longer need to keep the bridge powered for it.
Because of all of the above limitations we just need to implement a
bare-bones GPIO driver. The device tree bindings already account for
this device being a GPIO controller so we only need the driver changes
for it.
NOTE: Despite the fact that these pins are nominally muxable I don't
believe it makes sense to expose them through the pinctrl interface as
well as the GPIO interface. The special functions are things that the
bridge chip driver itself would care about and it can just configure
the pins as needed.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
[added pdata->gchip.base = -1;]
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200507143354.v5.1.Ia50267a5549392af8b37e67092ca653a59c95886@changeid
Most bridge drivers create a DRM connector to model the connector at the
output of the bridge. This model is historical and has worked pretty
well so far, but causes several issues:
- It prevents supporting more complex display pipelines where DRM
connector operations are split over multiple components. For instance a
pipeline with a bridge connected to the DDC signals to read EDID data,
and another one connected to the HPD signal to detect connection and
disconnection, will not be possible to support through this model.
- It requires every bridge driver to implement similar connector
handling code, resulting in code duplication.
- It assumes that a bridge will either be wired to a connector or to
another bridge, but doesn't support bridges that can be used in both
positions very well (although there is some ad-hoc support for this in
the analogix_dp bridge driver).
In order to solve these issues, ownership of the connector should be
moved to the display controller driver (where it can be implemented
using helpers provided by the core).
Extend the bridge API to allow disabling connector creation in bridge
drivers as a first step towards the new model. The new flags argument to
the bridge .attach() operation allows instructing the bridge driver to
skip creating a connector. Unconditionally set the new flags argument to
0 for now to keep the existing behaviour, and modify all existing bridge
drivers to return an error when connector creation is not requested as
they don't support this feature yet.
The change is based on the following semantic patch, with manual review
and edits.
@ rule1 @
identifier funcs;
identifier fn;
@@
struct drm_bridge_funcs funcs = {
...,
.attach = fn
};
@ depends on rule1 @
identifier rule1.fn;
identifier bridge;
statement S, S1;
@@
int fn(
struct drm_bridge *bridge
+ , enum drm_bridge_attach_flags flags
)
{
... when != S
+ if (flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR) {
+ DRM_ERROR("Fix bridge driver to make connector optional!");
+ return -EINVAL;
+ }
+
S1
...
}
@ depends on rule1 @
identifier rule1.fn;
identifier bridge, flags;
expression E1, E2, E3;
@@
int fn(
struct drm_bridge *bridge,
enum drm_bridge_attach_flags flags
) {
<...
drm_bridge_attach(E1, E2, E3
+ , flags
)
...>
}
@@
expression E1, E2, E3;
@@
drm_bridge_attach(E1, E2, E3
+ , 0
)
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-10-laurent.pinchart@ideasonboard.com
If we fail training at a lower DP link rate let's now keep trying
until we run out of rates to try. Basically the algorithm here is to
start at the link rate that is the theoretical minimum and then slowly
bump up until we run out of rates or hit the max rate of the sink. We
query the sink using a DPCD read.
This is, in fact, important in practice. Specifically at least one
panel hooked up to the bridge (AUO B116XAK01) had a theoretical min
rate more than 1.62 GHz (if run at 24 bpp) and fails to train at the
next rate (2.16 GHz). It would train at 2.7 GHz, though.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191218143416.v3.8.I251add713bc5c97225200894ab110ea9183434fd@changeid
The current bridge driver always forced us to use 24 bits per pixel
over the DP link. This is a waste if you are hooked up to a panel
that only supports 6 bits per color or fewer, since in that case you
can run at 18 bits per pixel and thus end up at a lower DP clock rate.
Let's support this.
While at it, let's clean up the math in the function to avoid rounding
errors (and round in the correct direction when we have to round).
Numbers are sufficiently small (because mode->clock is in kHz) that we
don't need to worry about integer overflow.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[narmstrong: s/ran/can/]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191218143416.v3.6.Iaf8d698f4e5253d658ae283d2fd07268076a7c27@changeid
The ti-sn65dsi86 is a bridge from MIPI to DP and thus has two links:
the MIPI link and the DP link. The two links do not need to have the
same format or number of lanes. Stop using MIPI variables when
talking about the DP link.
This has zero functional change because:
* currently we are hardcoding the MIPI link as unpacked RGB888 which
requires 24 bits and currently we are not changing the DP link rate
from the bridge's default of 8 bits per pixel.
* currently we are hardcoding both the MIPI and DP as being 4 lanes.
This is all in prep for fixing some of the above.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191218143416.v3.3.Ia6e05f4961adb0d4a0d32ba769dd7781ee8db431@changeid
