If endpoint has an invalid configuration, ignore it instead of happily
proceeding to use it nonetheless. Ignoring such an endpoint is better than
failing since there could be multiple endpoints, only some of which are
bad.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If regulator returns -EPROBE_DEFER, we need to return it too, so that
omap3isp will be re-probed when regulator is ready.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
CSI-2 PHY power management is only needed for major version 15 of the ISP.
Additionally, set the CCP2 PHY for previous ISP versions as well.
These changes are necessary for CCP2 support.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The omap3isp driver extracts the CSI-2 lane configuration from the V4L2
fwnode endpoint but misses the number of lanes itself. Get this information
and use it in PHY configuration.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The CSI-2 phy driver did initialise mutexes in its init function but there
was no corresponding cleanup function destroying them. Fix that. Also
clean up ISP module initialisation a little.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check that we do have a valid port in an endpoint, return an error if not.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Switch users of the v4l2_of_ APIs to the more generic v4l2_fwnode_ APIs.
Async OF matching is replaced by fwnode matching and OF matching support
is removed.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Benoit Parrot <bparrot@ti.com> # i2c/ov2569.c, am437x/am437x-vpfe.c and ti-vpe/cal.c
Tested-by: Hans Verkuil <hans.verkuil@cisco.com> # Atmel sama5d3 board + ov2640 sensor
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The OMAP IOMMU driver has added the support for IOMMU groups internally,
and the ISP device is automatically linked to the appropriate IOMMU group.
So, remove the explicit function calls that creates/deletes an iommu_group
and adds the ISP device to this group.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Both functions initialize the file handle with v4l2_fh_init() and thus
need to call clean up with v4l2_fh_exit() as appropriate. Fix it.
Signed-off-by: Shailendra Verma <shailendra.v@samsung.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The function has a local variable that points to the media device; use
that instead of finding the media device under the entity.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The media_entity_pipeline_start() and media_entity_pipeline_stop()
functions are renamed as media_pipeline_start() and media_pipeline_stop(),
respectively. The reason is two-fold: the pipeline struct is, rightly,
already called media_pipeline (rather than media_entity_pipeline) and what
this really is about is a pipeline. A pipeline consists of entities ---
and, well, other objects embedded in these entities.
As the pipeline object will be in the future moved from entities to pads
in order to support multiple pipelines through a single entity, do the
renaming now.
Similarly, functions operating on struct media_entity_graph as well as the
struct itself are renamed by dropping the "entity_" part from the prefix
of the function family and the data structure. The graph traversal which
is what the functions are about is not specifically about entities only
and will operate on pads for the same reason as the media pipeline.
The patch has been generated using the following command:
git grep -l media_entity |xargs perl -i -pe '
s/media_entity_pipeline/media_pipeline/g;
s/media_entity_graph/media_graph/g'
And a few manual edits related to line start alignment and line wrapping.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When requesting the DMA channel it was mandatory that we do not have DMA
resource nor valid DMA channel via DT. In this case the
dma_request_slave_channel_compat() would fall back and request any channel
with SW trigger.
The same can be achieved with the dma_request_chan_by_mask() without the
misleading use of the DMAengine API - implying that the omap3isp does
need to have DMA resource or valid dma binding in DT.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When parsing the graph the driver loops over all endpoints using
of_graph_get_next_endpoint(). The function handles reference counting of
the passed and returned nodes, so the returned node's reference count
must not be decreased manually in the normal path.
Move the offending of_node_put() call to the error path that requires
manual reference count handling.
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Due to the 80-cols restrictions, and latter due to checkpatch
warnings, several strings were broken into multiple lines. This
is not considered a good practice anymore, as it makes harder
to grep for strings at the source code.
As we're right now fixing other drivers due to KERN_CONT, we need
to be able to identify what printk strings don't end with a "\n".
It is a way easier to detect those if we don't break long lines.
So, join those continuation lines.
The patch was generated via the script below, and manually
adjusted if needed.
</script>
use Text::Tabs;
while (<>) {
if ($next ne "") {
$c=$_;
if ($c =~ /^\s+\"(.*)/) {
$c2=$1;
$next =~ s/\"\n$//;
$n = expand($next);
$funpos = index($n, '(');
$pos = index($c2, '",');
if ($funpos && $pos > 0) {
$s1 = substr $c2, 0, $pos + 2;
$s2 = ' ' x ($funpos + 1) . substr $c2, $pos + 2;
$s2 =~ s/^\s+//;
$s2 = ' ' x ($funpos + 1) . $s2 if ($s2 ne "");
print unexpand("$next$s1\n");
print unexpand("$s2\n") if ($s2 ne "");
} else {
print "$next$c2\n";
}
$next="";
next;
} else {
print $next;
}
$next="";
} else {
if (m/\"$/) {
if (!m/\\n\"$/) {
$next=$_;
next;
}
}
}
print $_;
}
</script>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This will allow adding new operations without increasing the
media_device structure size for drivers that don't implement any media
device operation.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Replace all calls to g/s_crop by calls to the get/set_selection pad ops.
Remove the old g/s_crop video ops since they are now no longer used.
The cropcap video op is now only used to pass pixelaspect information,
and is only needed if the pixelaspect is not 1:1.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make this a proper typed array. Drop the old allocate context code since
that is no longer used.
Note that the memops functions now get a struct device pointer instead of
the struct device ** that was there initially (actually a void pointer to
a struct containing only a struct device pointer).
This code is now a lot cleaner.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Stop using alloc_ctx and just fill in the device pointer.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mikhail Ulyanov <mikhail.ulyanov@cogentembedded.com>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
All users of is_media_entity_v4l2_io() (the exynos4-is, omap3isp,
davince_vpfe and omap4iss drivers and the v4l2-mc power management code)
use the function to check whether entities are video_device instances,
either to ensure they can cast the entity to a struct video_device, or
to count the number of video nodes users.
The purpose of the function is thus to identify whether the media entity
instance is an instance of the video_device object, not to check whether
it can perform I/O. Rename it accordingly, we will introduce a more
specific is_media_entity_v4l2_io() check when needed.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Power on devices represented by entities in the graph through the pipeline
state using V4L2 graph PM operations instead of what was in the omap3isp
driver.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The v4l2_of_parse_endpoint() function can fail so check the return value.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The data-shift DT property speficies the number of bits to be shifted,
but the driver still interprets the value as a multiple of two bits as
used by now removed platform data support. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The sequence number counter is incremented on each output buffer, and that
incremented value is used as the sequence number of that buffer. The input
buffer sequence numbering is based just on reading the same counter. If
the input buffer is marked done first, its sequence number ends up being
that of the output buffer - 1.
This is how the resizer works as well.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The function can return negative value.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/assign_signed_to_unsigned.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2046107
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
use the vb2_buffer_state enum for assigning the state
of the vb2 buffer, along side making isp_pipeline_state
state variable local to the block.
This fixes the following sparse warning as well:
drivers/media/platform/omap3isp/ispvideo.c:497:35: warning: mixing different enum types
drivers/media/platform/omap3isp/ispvideo.c:497:35: int enum isp_pipeline_state versus
drivers/media/platform/omap3isp/ispvideo.c:497:35: int enum vb2_buffer_state
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When the video buffer queue was stopped before the stream source was started
in omap3isp_streamon(), the buffers were not returned back to videobuf2.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Move the starting of the sensor from the VIDIOC_STREAMON handler to the
videobuf2 queue op start_streaming. This avoids failing starting the stream
after vb2_streamon() has already finished.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Platform drivers needs to export the OF id table and this be built
into the module or udev will not have the necessary information to
autoload the driver module when the device is registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of using a bitmap directly in a driver, use the new media entity
enumeration interface to perform the same.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The media graph walk requires initialisation and cleanup soon. Update the
users to perform the soon necessary API calls.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The media device node is registered and so made visible to user-space
before entities are registered and links created which means that the
media graph obtained by user-space could be only partially enumerated
if that happens too early before all the graph has been created.
To avoid this race condition, split the media init and registration
in separate functions and only register the media device node when
all the pending subdevices have been registered, either explicitly
by the driver or asynchronously using v4l2_async_register_subdev().
The media_device_register() had a check for drivers not filling dev
and model fields but all drivers in mainline set them and not doing
it will be a driver bug so change the function return to void and
add a BUG_ON() for dev being NULL instead.
Also, add a media_device_cleanup() function that will destroy the
graph_mutex that is initialized in media_device_init().
[mchehab@osg.samsung.com: Fix compilation if !CONFIG_MEDIA_CONTROLLER
and remove two warnings added by this changeset]
Suggested-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The isp_subdev_notifier_complete() complete callback defines a struct
v4l2_device *v4l2_dev to avoid needing two level of indirections to
access the V4L2 subdevs but the var is not always used when possible
as when calling v4l2_device_register_subdev_nodes().
So change that to consistently use the defined v4l2_dev pointer var.
Suggested-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Commit bc36b30fe06b ("[media] omap3isp: separate links creation from
entities init") moved the link creation logic from the entities init
functions and so removed the error_link labels from the error paths.
But after that, some functions have a single error label so it makes
more sense to rename the label to just "error" in thi case.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The function that creates the links between ISP internal and external
entities is called isp_create_pads_links() but the "pads" prefix is
redundant since the driver doesn't handle any other kind of link so
it can just be removed.
While being there, fix the function's kernel-doc since is not using
a proper format.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The entities to video nodes links were created on separate functions for
each ISP module but since the only thing that these functions do is to
call media_create_pad_link(), there's no need for that indirection level
and all link creation logic can be just inlined in the caller function.
Also, since the only possible failure for the link creation is a memory
allocation, there is no need for error messages since the core already
reports a very verbose message in that case.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The pad index is unsigned. Replace the occurences of it where
pertinent.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
With the MC next gen rework, what's left for media_entity_init()
is to just initialize the PADs. However, certain devices, like
a FLASH led/light doesn't have any input or output PAD.
So, there's no reason why calling media_entity_init() would be
mandatory. Also, despite its name, what this function actually
does is to initialize the PADs data. So, rename it to
media_entity_pads_init() in order to reflect that.
The media entity actual init happens during entity register,
at media_device_register_entity(). We should move init of
num_links and num_backlinks to it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
On omap3/omap4/davinci drivers, MEDIA_ENT_T_V4L2_SUBDEV macro is
abused in order to "simplify" the pad checks.
Basically, it does a logical or of this macro, in order to check
for a local index and if the entity is either a subdev or not.
As we'll get rid of MEDIA_ENT_T_V4L2_SUBDEV macro, replace it by
2 << 16 where it occurs, and add a note saying that the code
there is actually a hack.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of relying on media subtype, use the new macros to detect
if an entity is a subdev or an A/V DMA entity.
Please note that most drivers assume that there's just AV_DMA or
V4L2 subdevs. This is not true anymore, as we've added MC support
for DVB, and there are plans to add support for ALSA and FB/DRM
too.
Ok, on the current pipelines supported by those drivers, just V4L
stuff are there, but, assuming that some day a pipeline that also
works with other subsystems will ever added, it is better to add
explicit checks for the AV_DMA stuff.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The omap3isp driver parses the graph endpoints to know how many subdevices
needs to be registered async and register notifiers callbacks for to know
when these are bound and when the async registrations are completed.
Currently the entities pad are linked with the correct ISP input interface
when the subdevs are bound but it happens before entitities are registered
with the media device so that won't work now that the entity links list is
initialized on device registration.
So instead creating the pad links when the subdevice is bound, create them
on the complete callback once all the subdevices have been bound but only
try to create for the ones that have a bus configuration set during bound.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The omap3isp driver initializes the entities and creates the pads links
before the entities are registered with the media device. This does not
work now that object IDs are used to create links so the media_device
has to be set.
Split out the pads links creation from the entity initialization so the links
are created after the entities have been registered with the media device.
Suggested-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The struct media_entity has a .parent field that stores a pointer
to the parent struct media_device. But recently a media_gobj was
embedded into the entities and since struct media_gojb already has
a pointer to a struct media_device in the .mdev field, the .parent
field becomes redundant and can be removed.
This patch replaces all the usage of .parent by .graph_obj.mdev so
that field will become unused and can be removed on a later patch.
No functional changes.
The transformation was made using the following coccinelle spatch:
@@
struct media_entity *me;
@@
- me->parent
+ me->graph_obj.mdev
@@
struct media_entity *link;
@@
- link->source->entity->parent
+ link->source->entity->graph_obj.mdev
@@
struct exynos_video_entity *ve;
@@
- ve->vdev.entity.parent
+ ve->vdev.entity.graph_obj.mdev
Suggested-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
With the new API, a link can be either between two PADs or between an interface
and an entity. So, we need to use a better name for the function that create
links between two pads.
So, rename the such function to media_create_pad_link().
No functional changes.
This patch was created via this shell script:
for i in $(find drivers/media -name '*.[ch]' -type f) $(find drivers/staging/media -name '*.[ch]' -type f) $(find include/ -name '*.h' -type f) ; do sed s,media_entity_create_link,media_create_pad_link,g <$i >a && mv a $i; done
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Accessing media_entity ID should now use media_entity_id() macro to
obtain the entity ID, as a next patch will remove the .id field from
struct media_entity .
So, get rid of it, otherwise the omap3isp driver will fail to build.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Currently, media_entity_init() creates an array with the links,
allocated at init time. It provides a parameter (extra_links)
that would allocate more links than the current needs, but this
is not used by any driver.
As we want to be able to do dynamic link allocation/removal,
we'll need to change the implementation of the links. So,
before doing that, let's first remove that extra unused
parameter, in order to cleanup the interface first.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Move timestamp from struct vb2_v4l2_buffer to struct vb2_buffer
for common use, and change its type to u64 in order to handling
y2038 problem. This patch also includes all device drivers' changes related to
this restructuring.
Signed-off-by: Junghak Sung <jh1009.sung@samsung.com>
Signed-off-by: Geunyoung Kim <nenggun.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The queue_setup callback has a void pointer that is just for V4L2
and is the pointer to the v4l2_format struct that was passed to
VIDIOC_CREATE_BUFS. The idea was that drivers would use the information
from that struct to buffers suitable for the requested format.
After the vb2 split series this pointer is now a void pointer,
which is ugly, and the reality is that all existing drivers will
effectively just look at the sizeimage field of v4l2_format.
To make this more generic the queue_setup callback is changed:
the void pointer is dropped, instead if the *num_planes argument
is 0, then use the current format size, if it is non-zero, then
it contains the number of requested planes and the sizes array
contains the requested sizes. If either is unsupported, then return
-EINVAL, otherwise use the requested size(s).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Replace struct v4l2_format * with void * to make queue_setup()
for common use.
And then, modify all device drivers related with this change.
Signed-off-by: Junghak Sung <jh1009.sung@samsung.com>
Signed-off-by: Geunyoung Kim <nenggun.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: fix missing const in fimc-lite.c]
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove v4l2 stuff - v4l2_buf, v4l2_plane - from struct vb2_buffer.
Add new member variables - bytesused, length, offset, userptr, fd,
data_offset - to struct vb2_plane in order to cover all information
of v4l2_plane.
struct vb2_plane {
<snip>
unsigned int bytesused;
unsigned int length;
union {
unsigned int offset;
unsigned long userptr;
int fd;
} m;
unsigned int data_offset;
}
Replace v4l2_buf with new member variables - index, type, memory - which
are common fields for buffer management.
struct vb2_buffer {
<snip>
unsigned int index;
unsigned int type;
unsigned int memory;
unsigned int num_planes;
struct vb2_plane planes[VIDEO_MAX_PLANES];
<snip>
};
v4l2 specific fields - flags, field, timestamp, timecode,
sequence - are moved to vb2_v4l2_buffer in videobuf2-v4l2.c
struct vb2_v4l2_buffer {
struct vb2_buffer vb2_buf;
__u32 flags;
__u32 field;
struct timeval timestamp;
struct v4l2_timecode timecode;
__u32 sequence;
};
Signed-off-by: Junghak Sung <jh1009.sung@samsung.com>
Signed-off-by: Geunyoung Kim <nenggun.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make videobuf2-v4l2 as a wrapper of videobuf2-core for v4l2-use.
And replace videobuf2-core.h with videobuf2-v4l2.h.
This renaming change should be accompanied by the modifications
of all device drivers that include videobuf2-core.h.
It can be done with just running this shell script.
replace()
{
str1=$1
str2=$2
dir=$3
for file in $(find $dir -name *.h -o -name *.c -o -name Makefile)
do
echo $file
sed "s/$str1/$str2/g" $file > $file.out
mv $file.out $file
done
}
replace "videobuf2-core" "videobuf2-v4l2" "include/media/"
replace "videobuf2-core" "videobuf2-v4l2" "drivers/media/"
replace "videobuf2-core" "videobuf2-v4l2" "drivers/usb/gadget/"
replace "videobuf2-core" "videobuf2-v4l2" "drivers/staging/media/"
Signed-off-by: Junghak Sung <jh1009.sung@samsung.com>
Signed-off-by: Geunyoung Kim <nenggun.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This is a preparation for a change to the type of v4l2 timestamps.
v4l2_get_timestamp() is a helper function that reads the monotonic
time and stores it into a 'struct timeval'. Multiple drivers implement
the same thing themselves for historic reasons.
Changing them all to use v4l2_get_timestamp() is more consistent
and reduces the amount of code duplication, and most importantly
simplifies the following changes.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
[hans.verkuil@cisco.com: dropped the v4l2-dev.c patch that didn't belong here]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Platforms using the OMAP3 ISP have all switched to DT, drop platform
data support.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Commit 813f5c0ac5 ("media: Change media device link_notify behaviour")
modified the media controller link setup notification API and updated the
OMAP3 ISP driver accordingly. As a side effect it introduced a bug by
turning power on after setting the link instead of before. This results in
sub-devices not being powered down in some cases when they should be. Fix
it.
Fixes: 813f5c0ac5 [media] media: Change media device link_notify behaviour
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Cc: stable@vger.kernel.org # since v3.10
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The async notifier was registered before the v4l2_device was registered and
before the notifier callbacks were set. This could lead to missing the
bound() and complete() callbacks and to attempting to spin_lock() and
uninitialised spin lock.
Also fix unregistering the async notifier in the case of an error --- the
function may not fail anymore after the notifier is registered.
Fixes: da7f3843d2 ("[media] omap3isp: Add support for the Device Tree")
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/platform/omap3isp/isppreview.c:932:6: warning: variable ‘features’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
No merged platform supplies xclks via platform data. As we want to
slightly change the clkdev interface, rather than fixing this unused
code, remove it instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Print a warning when the driver is used with platform data. Existing
platform data users should move to DT now.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add the ISP device to omap3 DT include file and add support to the driver to
use it.
Also obtain information on the external entities and the ISP configuration
related to them through the Device Tree in addition to the platform data.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The omap3isp MMIO register block is contiguous in the MMIO register space
apart from the fact that the ISP IOMMU register block is in the middle of
the area. Ioremap it at two occasions, and keep the rest of the layout of
the register space internal to the omap3isp driver.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The syscon register isn't part of the ISP, use it through the syscom driver
regmap instead. The syscom block is considered to be from 343x on ISP
revision 2.0 whereas 15.0 is assumed to have 3630 syscon.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Only the histogram sub-block driver uses the physical address. Do not store
it for other sub-blocks.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The video port clock is l3_ick divided by vpclk_div. This clock must be high
enough for the external pixel rate. The video port requires two clock cycles
to process a pixel.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make omap3isp configuration data structures more suitable for consumption by
the DT by separating the I2C bus information of all the sub-devices in a
group and the ISP bus information from each other. The ISP bus information
is made a pointer instead of being directly embedded in the struct.
In the case of the DT only the sensor specific information on the ISP bus
configuration is retained. The structs are renamed to reflect that.
After this change the structs needed to describe device configuration can be
allocated and accessed separately without those needed only in the case of
platform data. The platform data related structs can be later removed once
the support for platform data can be removed.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Igor Grinberg <grinberg@compulab.co.il> (for cm-t35)
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Only check for call platform data callback functions if there's platform
data. Also take care of a few other cases where the NULL pdata pointer could
have been accessed, and remove the check for NULL dev->platform_data
pointer.
Removing the check for NULL dev->platform_data isn't strictly needed by the
DT support but there's no harm from that either: the device now can be used
without sensors, for instance.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Move the code which connects the external entity to an ISP entity into a
separate function. This disconnects it from parsing the platform data.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If an uninitialised v4l2_subdev struct was passed to
media_entity_create_link(), one of the BUG_ON()'s in the function will be
hit since media_entity.num_pads will be zero. Avoid this by checking whether
the num_pads field is non-zero for the interface.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The mutex was not destroyed correctly if dma_coerce_mask_and_coherent()
failed for some reason.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Replace the custom OMAP DMA API usage by DMA engine. Feature-wise the
driver has lost the ability to get notified of DMA transfers failure
through the completion handler, as the DMA engine API doesn't expose
that status information.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Replace the open-coded copy by a function call.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There isn't a need to assign the state of vb2_buffer to active
as this is already done by the core.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
videobuf2 has long been subject to AB-BA style deadlocks due to the
queue lock and mmap_sem being taken in different orders for the mmap
operation. The problem has been fixed by making this operation callable
without taking the queue lock, using an mmap_lock internal to videobuf2.
The omap3isp driver still calls the mmap operation with the queue lock
held, resulting in a potential deadlock. As the operation can now be
called without locking the queue, fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Support the new 'which' field in the enum_frame_size ops. Most drivers do not
need to be changed since they always returns the same enumeration regardless
of the 'which' field.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Tested-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Support the new 'which' field in the enum_mbus_code ops. Most drivers do not
need to be changed since they always return the same enumeration regardless
of the 'which' field.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If a subdevice pad op is called from a bridge driver, then there is
no v4l2_subdev_fh struct that can be passed to the subdevice. This
made it hard to use such subdevs from a bridge driver.
This patch replaces the v4l2_subdev_fh pointer by a v4l2_subdev_pad_config
pointer in the pad ops. This allows bridge drivers to use the various
try_ pad ops by creating a v4l2_subdev_pad_config struct and passing it
along to the pad op.
The v4l2_subdev_get_try_* macros had to be changed because of this, so
I also took the opportunity to use the full name of the v4l2_subdev_get_try_*
functions in the __V4L2_SUBDEV_MK_GET_TRY macro arguments: if you now do
'git grep v4l2_subdev_get_try_format' you will actually find the header
where it is defined.
One remark regarding the drivers/staging/media/davinci_vpfe patches: the
*_init_formats() functions assumed that fh could be NULL. However, that's
not true for this driver, it's always set. This is almost certainly a copy
and paste from the omap3isp driver. I've updated the code to reflect the
fact that fh is never NULL.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Tested-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUxbzlAAoJEHm+PkMAQRiGtqYIAJ8YlKX9cXKYmXx8/FncINH+
2erj94KyHG080R1uwSq1+7zXWCZUUlxiJnDnsup5rG0dImcicqgOE48oHax1aN6b
yHfPONkTjNJ1HYepuGC3YWCG9wIjPZQ5S8KHrwRjyVoE+ddhe9gWgvArA3jl/fW/
2fYNWekoRoMcRiNb4/w2weyOOBywdSVpmj0WYiwdztysG2ymw5hUXRHJhvSf1AFm
RQJfUHkhCOYpQGY7XFba/1uGhTJfOgDmYAfspAOLzmrXE/DJcCutsVdBZO+12fAL
nhGpM/PkRYxMvwzDKIUoG35qsymYOMqo54oXhr0S2JjyXTGdGmB6qHxIfqnV5Tk=
=O/Lr
-----END PGP SIGNATURE-----
Merge tag 'v3.19-rc6' into patchwork
This is needed in order to get the media fixes applied on -rc6.
Linux 3.19-rc6
* tag 'v3.19-rc6': (891 commits)
Linux 3.19-rc6
dm: fix handling of multiple internal suspends
hwmon: (i5500_temp) Convert to use ATTRIBUTE_GROUPS macro
hwmon: (i5500_temp) Convert to module_pci_driver
hwmon: (i5500_temp) Don't bind to disabled sensors
hwmon: (i5500_temp) Convert to devm_hwmon_device_register_with_groups
hwmon: (i5500_temp) New driver for the Intel 5500/5520/X58 chipsets
arm64: dts: add baud rate to Juno stdout-path
Revert "platform: x86: dell-laptop: Add support for keyboard backlight"
Revert "Documentation: Add entry for dell-laptop sysfs interface"
dm cache: fix problematic dual use of a single migration count variable
dm cache: share cache-metadata object across inactive and active DM tables
of/unittest: Overlays with sub-devices tests
KVM: x86: SYSENTER emulation is broken
KVM: x86: Fix of previously incomplete fix for CVE-2014-8480
arm64: dump: Fix implicit inclusion of definition for PCI_IOBASE
x86/tsc: Change Fast TSC calibration failed from error to info
x86/apic: Re-enable PCI_MSI support for non-SMP X86_32
x86, mm: Change cachemode exports to non-gpl
x86, tls: Interpret an all-zero struct user_desc as "no segment"
...
Conflicts:
drivers/media/pci/cx23885/cx23885.h
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=yD+L
-----END PGP SIGNATURE-----
Merge tag 'media/v3.19-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- fix some race conditions caused by a regression on videobuf2
- fix a interrupt release bug on cx23885
- fix support for Mygica T230 and HVR4400
- fix compilation breakage when USB is not selected on tlg2300
- fix capabilities report on ompa3isp, soc-camera, rcar_vin and
pvrusb2
* tag 'media/v3.19-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] omap3isp: Correctly set QUERYCAP capabilities
[media] cx23885: fix free interrupt bug
[media] pvrusb2: fix missing device_caps in querycap
[media] vb2: fix vb2_thread_stop race conditions
[media] rcar_vin: Update device_caps and capabilities in querycap
[media] soc-camera: fix device capabilities in multiple camera host drivers
[media] Fix Mygica T230 support
[media] cx23885: Split Hauppauge WinTV Starburst from HVR4400 card entry
[media] tlg2300: Fix media dependencies
device_caps in struct v4l2_capability were inadequately set in
VIDIOC_QUERYCAP. Fix this. Without this a WARN_ON in the v4l2 core
is triggered. This WARN_ON was added for kernel 3.19 exactly to
detect these situations.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If the requested clock rate passed to the XCLK set_rate or round_rate
operation is 0, the driver will try to divide by 0. Fix this.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
In order to have subsytem agnostic media bus format definitions we've
moved media bus definition to include/uapi/linux/media-bus-format.h and
prefixed values with MEDIA_BUS_FMT instead of V4L2_MBUS_FMT.
Reference new definitions in all platform drivers.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When updating the crop rectangle during streaming, the IRQ handler will
reprogram the resizer after the current frame. A race condition
currently exists between the set selection operation and the IRQ
handler: if the set selection operation is called twice in a row and the
IRQ handler runs only during the second call, it could reprogram the
hardware with partially updated values. Use a spinlock to protect
against that.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The resizer_set_input_size() function prints a debugging message with
the input width and height values. As the function is called from
interrupt context, printing that message to the serial console could
slow down the interrupt handler and cause it to miss the start of the
next frame, causing image corruption.
Fix this by reorganizing the resizer debug messages. The driver now
prints the input size, the crop rectangle and the output size in the set
selection handler instead of scattering debug messages in various
places.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There's no need to initialize local variables to zero when they're
explicitly assigned another value right after. Remove the needless
initializations.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As the CCDC doesn't generate interrupts when stopped in BT.656 mode,
restart it immediately when the next buffer after an underrun is queued
instead of relying on the interrupt handler to restart the CCDC.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Enrico Butera <ebutera@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When the CCDC is already stopped due to a buffer underrun, the stop
state machine won't advance in BT.656 mode as no interrupt are generated
by the stopped CCDC in that mode. Handle this case explicitly in the
ccdc_disable() function.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Enrico Butera <ebutera@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In BT.656 mode the synchronization signals are generated by the CCDC
from the embedded sync codes. The VD0 and VD1 interrupts are thus only
triggered when the CCDC is enabled, unlike external sync mode where the
line counter runs even when the CCDC is stopped. We can't disable the
CCDC at VD1 time, as no VD0 interrupt would be generated for a short
frame, which would result in the CCDC being stopped and no VD interrupt
generated anymore. The CCDC is stopped from the VD0 interrupt handler
instead for BT.656.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Enrico Butera <ebutera@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
We will stop using VD1 in BT.656 mode, move frame number increment to
the VD0 interrupt handler.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Enrico Butera <ebutera@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Use a local variable to avoid the duplicate spin_unlock_irqrestore()
call.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Enrico Butera <ebutera@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There's no need for a double underscore in the function name, remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Enrico Butera <ebutera@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Checking that the captured field corresponds to the last required field
depending on the requested field order before completing the buffer
isn't enough. When the first field at stream start corresponds to the
last required field, this would result in returning an interlaced buffer
containing a single field.
Fix this by keeping track of the fields captured in the buffer, and make
sure that both fields are present for alternate field orders.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Enrico Butera <ebutera@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video port doesn't support YUV formats. Disable it when the CCDC
sink pad format is set to YUV instead of leaving it enabled and relying
on downstream modules not to process data they receive from the video
port.
Experiments showed that this fixes some of the CCDC failures to stop,
especially in BT.656 mode.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Enrico Butera <ebutera@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Query the CCDC input media bus type from the subdev connected to the
CCDC sink pad and configure the CCDC accordingly to support BT.656
synchronization.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Enrico Butera <ebutera@users.sourceforge.net>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The CCDC can interleave fields into a single buffer when writing to
memory. Support it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Enrico Butera <ebutera@users.sourceforge.net>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When the CCDC input is interlaced enable the alternate field order on
the CCDC output video node. The field signal polarity is specified
through platform data.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Enrico Butera <ebutera@users.sourceforge.net>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of using goto statements to a single line return, return the
correct value immediately.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Enrico Butera <ebutera@users.sourceforge.net>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Assign the format variable to the sink pad format earlier and use it
instead of accessing the sink pad format directly from the ISP
structure.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Enrico Butera <ebutera@users.sourceforge.net>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
